Graco PD44, 313876M Maintenance Manual

Operation - Maintenance

PD44

Metering Valves and Feed Systems

Meter, mix, and dispense system for precise two-component micro-dispensing of sealants and adhesives. Not approved for use in European explosive atmosphere locations.

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

See page 3 for model information, including maximum working pressure and approvals. See page 7 for product configuration information.

313876M

Linear Resistive Transducer PD44 Meter-

ing Valve shown, Feed Systems not shown

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Isocyanate Conditions . . . . . . . . . . . . . . . . . . . . . . 6

Material Self-ignition . . . . . . . . . . . . . . . . . . . . . . . 6

Moisture Sensitivity of Isocyanates . . . . . . . . . . . . 6

Keep Components A and B Separate . . . . . . . . . . 6

Foam Resins with 245 fa Blowing Agents . . . . . . . 6

Changing Materials . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Configurator . . . . . . . . . . . . . . . . . . . . . . . 7

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Component Identification . . . . . . . . . . . . . . . . . . . 13

Typical System Configurations . . . . . . . . . . . . . 13

Typical Feed System Components . . . . . . . . . 14

Micrometer PD44 Metering Valve . . . . . . . . . . . 15

LRT PD44 Metering Valve . . . . . . . . . . . . . . . . 16

Motor Driven PD44 Metering Valve . . . . . . . . . . 17

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Typical Installation . . . . . . . . . . . . . . . . . . . . . . 18

Tank Level Sensor Wiring Schematic . . . . . . . . 19

Valve Mounting Diagram . . . . . . . . . . . . . . . . . . 19

Motor Mounting Diagram . . . . . . . . . . . . . . . . . 20

Custom Drive Mounting Diagram . . . . . . . . . . . 20

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjusting the Shot Size . . . . . . . . . . . . . . . . . . . . . 22

Micrometer PD44 Only . . . . . . . . . . . . . . . . . . . 22

LRT and Motor Driven PD44 . . . . . . . . . . . . . . . 22

Ratio Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Sequence of Operation . . . . . . . . . . . . . . . . . . . 24

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 25

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Rebuild . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Wetted Section Disassembly . . . . . . . . . . . . . . . 27

Wetted Section Reassembly . . . . . . . . . . . . . . . 29

Spool Valve Rebuild . . . . . . . . . . . . . . . . . . . . . 30

Wetted Section Rebuild . . . . . . . . . . . . . . . . . . . 31

Micrometer Drive Rebuild

(Micrometer PD44 Only) . . . . . . . . . . . . . . . 34

Electrical Requirements . . . . . . . . . . . . . . . . . . . . 36

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

California Proposition 65 . . . . . . . . . . . . . . . . . . 40

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 42

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 42

2 313876M

Related Manuals

Manuals are available at www.graco.com

Component manuals in U.S. English.

PD44 Manuals

Part Description

313877 PD44 Control Box Setup - Operation

3A0987 PD44 Parts

Feed System Manuals

306565 Air-Driven, Stainless Steel Agitators

307043

308116 Severe-Duty, UHMWPE/PTFE or PTFE

308167 Low Volume Air Regulators

308168 High Volume Air Regulators

308169 Air Filters, Lubricators and Kits

309306

312376 Stainless Steel Agitator Kit

313526

3A1452 20 oz Cartridge

Monark

Packed Stainless Steel Pumps

Air-Operated Husky™ Diaphragm Pumps

Check-Mate® Pump Packages

Air Motor

Related Manuals

Models

Max Outlet

Fluid Working

Metering Valve

Model

Linear Resistive

Transducer (LRT)

Micrometer

Motor Driven

* If a custom PD44 is ordered, it will not be CE

approved unless otherwise noted.

Pressure

psi (MPa, bar)

2000 (14, 138) 100 (0.7, 7) 1200 (8, 83) 400 (2.8, 28)

psi (MPa, bar)

Max Air

Working

Pressure

Max Inlet Working Pressure

psi (MPa, bar)

Approved*Metal Sleeves Plastic Sleeves



313876M 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the dispense outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning, checking, or servicing equipment.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

• Always wear impervious gloves when spraying or cleaning equipment.

• If this equipment is used with isocyanate material, see additional information on isocyanates in Isocyanate Conditions Section of this manual.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eyewear

• Clothing and respirator as recommended by the fluid and solvent manufacturer

• Gloves

• Hearing protection

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

• Ground all equipment in the work area. See Grounding instructions.

• Use only grounded hoses.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

4 313876M

Warnings

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure in this manual when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Use only compatible water-based solvents to clean plastic structural or pressure-containing parts. Many solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property damage. See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent manufacturer’s warnings.

313876M 5

Isocyanate Conditions

Spraying or dispensing materials containing isocyanates creates potentially harmful mists, vapors, and atomized particulates.

Read material manufacturer’s warnings and material MSDS to know specific hazards and precautions related to isocyanates.

Prevent inhalation of isocyanate mists, vapors, and atomized particulates by providing sufficient ventilation in the work area. If sufficient ventilation is not available, a supplied-air respirator is required for everyone in the work area.

To prevent contact with isocyanates, appropriate personal protective equipment, including chemically impermeable gloves, boots, aprons, and goggles, is also required for everyone in the work area.

Material Self-ignition

To prevent exposing ISO to moisture:

• Always use a sealed container with a desiccant dryer in the vent, or a nitrogen atmosphere. Never store ISO in an open container.

• Keep the ISO lube pump reservoir (if installed) filled with Graco Throat Seal Liquid (TSL™), Part 206994.

The lubricant creates a barrier between the ISO and the atmosphere.

• Use moisture-proof hoses specifically designed for ISO, such as those supplied with your system.

• Never use reclaimed solvents, which may contain moisture. Always keep solvent containers closed when not in use.

• Never use solvent on one side if it has been contaminated from the other side.

• Always lubricate threaded parts with ISO pump oil or grease when reassembling.

Keep Components A and B Separate

Some materials may become self-igniting if applied too thickly. Read material manufacturer’s warnings and material MSDS.

Moisture Sensitivity of Isocyanates

Isocyanates (ISO) are catalysts used in two component foam and polyurea coatings. ISO will react with moisture (such as humidity) to form small, hard, abrasive crystals, which become suspended in the fluid. Eventually a film will form on the surface and the ISO will begin to gel, increasing in viscosity. If used, this partially cured ISO will reduce performance and the life of all wetted parts.

NOTE: The amount of film formation and rate of crystallization varies depending on the blend of ISO, the humidity, and the temperature.

NOTICE

To prevent cross-contamination of the equipment’s wetted parts, never interchange component A (isocyanate) and component B (resin) parts.

Foam Resins with 245 fa Blowing Agents

Some foam blowing agents will froth at temperatures above 90°F (33°C) when not under pressure, especially if agitated. To reduce frothing, minimize preheating in a circulation system.

Changing Materials

• When changing materials, flush the equipment multiple times to ensure it is thoroughly clean.

• Always clean the fluid inlet strainers after flushing.

• Check with your material manufacturer for chemical compatibility.

• Most materials use ISO on the A side, but some use ISO on the B side.

• Epoxies often have amines on the B (hardener) side. Polyureas often have amines on the B (resin) side.

6 313876M

Product Configurator

This system can be ordered with many different options as shown in the configurator below.

Product Configurator

PD44 C - A - BCD -EFG- H - I - J - K - L - M - NO - P - Q - RS - T - U - V - W - X

Configurator Series Level

Base Unit

High Volume Rod Material, Size

Low Volume Rod Material, Size

High Volume Spool

Low Volume Spool

Outlet Nose

Mixer

Controls

Power Cord

High Volume Feed

High Volume Feed Hose

High Volume Feed Options

Low Volume Feed

Low Volume Feed Hose

Low Volume Feed Options

Vacuum Pump(s)

Bench Stand

Seal Lubricant

The following table applies to the PD44 configurations and indicates all of the options available for each letter shown above.

Code A Part Base Unit

A 964000 Micrometer PD44 B 964001 Linear Resistive Transducer PD44 C 964002 Motor Driven PD44

Code B Part High Volume Rod Material

NOTE: See code CD for last two digits of part number

A 9641__ Hardened Steel B 9642__ Stainless Steel, UHMW C 9643__ Tungsten Carbide, UHMW

Code

NOTE: See code B for first four digits of part number

Part High Volume Rod Size

19 ____19 3.75 mm rod diameter 20 ____20 4.00 mm rod diameter 21 ____21 4.25 mm rod diameter 22 ____22 4.50 mm rod diameter 23 ____23 4.63 mm rod diameter 24 ____24 4.75 mm rod diameter 25 ____25 4.88 mm rod diameter 26 ____26 5.00 mm rod diameter 27 ____27 5.13 mm rod diameter 28 ____28 5.25 mm rod diameter 29 ____29 5.50 mm rod diameter 30 ____30 5.75 mm rod diameter 31 ____31 6.00 mm rod diameter 32 ____32 6.13 mm rod diameter 33 ____33 6.25 mm rod diameter 34 ____34 6.38 mm rod diameter 35 ____35 6.50 mm rod diameter 36 ____36 6.63 mm rod diameter 37 ____37 6.75 mm rod diameter 38 ____38 7.00 mm rod diameter 39 ____39 7.25 mm rod diameter 40 ____40 7.50 mm rod diameter 41 ____41 7.63 mm rod diameter 42 ____42 7.75 mm rod diameter 43 ____43 7.88 mm rod diameter 44 ____44 8.00 mm rod diameter

313876M 7

Product Configurator

Code E Part Low Volume Rod Material

NOTE: See code FG for last two digits of part number

A 9641__ Hardened Steel B 9642__ Stainless Steel, UHMW

C 9643__ Tungsten Carbide, UHMW

Code FG Part Low Volume Rod Size

NOTE: See code E for first four digits of part number

01 ____01 1.25 mm rod diameter 02 ____02 1.38 mm rod diameter 03 ____03 1.50 mm rod diameter 04 ____04 1.63 mm rod diameter 05 ____05 1.75 mm rod diameter 06 ____06 2.00 mm rod diameter 07 ____07 2.13 mm rod diameter 08 ____08 2.25 mm rod diameter 09 ____09 2.38 mm rod diameter 10 ____10 2.50 mm rod diameter 11 ____11 2.63 mm rod diameter 12 ____12 2.75 mm rod diameter 13 ____13 3.00 mm rod diameter 14 ____14 3.13 mm rod diameter 15 ____15 3.25 mm rod diameter 16 ____16 3.38 mm rod diameter 17 ____17 3.50 mm rod diameter 18 ____18 3.63 mm rod diameter 19 ____19 3.75 mm rod diameter 20 ____20 4.00 mm rod diameter 21 ____21 4.25 mm rod diameter 22 ____22 4.50 mm rod diameter 23 ____23 4.63 mm rod diameter 24 ____24 4.75 mm rod diameter 25 ____25 4.88 mm rod diameter 26 ____26 5.00 mm rod diameter 27 ____27 5.13 mm rod diameter 28 ____28 5.25 mm rod diameter 29 ____29 5.50 mm rod diameter 30 ____30 5.75 mm rod diameter 31 ____31 6.00 mm rod diameter 32 ____32 6.13 mm rod diameter 33 ____33 6.25 mm rod diameter 34 ____34 6.38 mm rod diameter 35 ____35 6.50 mm rod diameter 36 ____36 6.63 mm rod diameter 37 ____37 6.75 mm rod diameter 38 ____38 7.00 mm rod diameter 39 ____39 7.25 mm rod diameter 40 ____40 7.50 mm rod diameter 41 ____41 7.63 mm rod diameter 42 ____42 7.75 mm rod diameter 43 ____43 7.88 mm rod diameter 44 ____44 8.00 mm rod diameter

Code H Part High Volume Spool

1 964003 High viscosity, HS 2 964004 High viscosity, Stainless Steel/UHMWPE 3 964005 High viscosity, TC/UHMWPE 4 964006 Low viscosity, Stainless Steel

Code I Part Low Volume Spool

1 964011 High viscosity, HS 2 964012 High viscosity, Stainless Steel/UHMWPE 3 964013 High viscosity, TC/UHMWPE 4 964014 Low viscosity, Stainless Steel

Code J Part Outlet Nose

1 964020 Luer lock, equal ports, no check valves 2 964021 Luer lock, equal ports, dual check valves 3 964022 Equal ports, 7/8-9, no check valves 4 964023 Large and small ports, 7/8-9, no check

valves

5 964024 Large and small ports, 7/8-9, single

check valve 6 964025 Dual small ports, 7/8-9, no check valves 7 964026 Dual small ports, 7/8-9 dual check valves

Code K Part Mixer

1 964027 1/8-24 Luer Lock inlet and outlet, 0.5 cc 2 964028 3/16-32 bell mouth inlet, luer lock outlet,

2.0 cc

3 964029 1/4-24 bell mouth inlet, luer lock outlet,

4.0 cc

4 964030 1/4-32 bell mouth inlet, luer lock outlet,

5.5 cc

5 964031 1/4-48 bell mouth inlet, luer lock outlet,

8.0 cc

6 964032 3/16-32 bell mouth inlet, tapered outlet,

1.5 cc

7 964033 1/4-24 bell mouth inlet, tapered outlet,

3.5 cc

8 964034 3/16-24 bell mouth inlet, tapered outlet,

1.0 cc

Code L Part Controls

1 964035 Pneumatic, micrometer, wire harness

only 6 964040 Pneumatic, linear resistive transducer,

wire harness only B 964045 Motor driven, I/O, wire harness only

D -- No Controls - use only with UniXact

motion table

E 25C687 No Controls with pressure transducer

block. Use only with UniXact motion table

8 313876M

Product Configurator

Code M Part Power Cord

1 121055 120 VAC, North American cord set 2 121054 250 VAC, 1 phase, no plug 3 121056 10 amp, 250 volt, continental Europe 4 121057 10 amp, 250 volt, United Kingdom and

Ireland 5 121058 10 amp, 250 volt, Israel 6 124864 10 amp, 250 volt, Australia 7 124861 10 amp, 250 volt, Italy 8 124863 10 amp, 250 volt, Switzerland 9 124862 10 amp, 250 volt, Denmark A 121060 10 amp, 250 volt, India N -- None

Code

01 964050 02 964051 03 964052 04 964053

05 964054 06 964055

07 964056

08 964057

NN --

Code P Part High Volume Feed Hose

1 964082 1/2 in. x 8 ft PTFE and stainless steel

3 964084 1/2 in. x 10 ft PTFE and stainless steel

5 964086 1/2 in. x 15 ft PTFE and stainless steel

N -- None

Code Q Part High Volume Feed

C 964090 Low level sensor 11:1 Ram only N -- None

Part High Volume Feed

20 oz cartridge feed with mounting post

1 gallon pail Ram and transfer pump

5 gallon pail cover with diaphragm pump

5 gallon pail cover diaphragm pump and

agitator

5 gallon pail cover and 5:1 transfer pump

5 gallon pail cover, 1:1 pump with dip

tube for moisture sensitive materials

5 gallon single post Ram with 11:1 pump,

mild steel

5 gallon single post Ram with 11:1 pump,

stainless steel

None

hose, stainless steel fittings

Code RS Part Low Volume Feed

01 964050 02 964051 03 964052 04 964053

05 964054 06 964055

07 964056

08 964057

NN --

Code T Part Low Volume Feed Hose

1 964082 1/2 in. x 8 ft PTFE and stainless steel

3 964084 1/2 in. x 10 ft PTFE and stainless steel

5 964086 1/2 in. x 15 ft PTFE and stainless steel

7 -- None

Code U Part Low Volume Feed

C 964090 Low level sensor 11:1 Ram only N -- None

Code V Part Vacuum Pump(s)

N -- None

Code W Part Bench Stand

A 964095 Adjustable height bench stand N -- None

Code X Part Seal Lubricant

T 206994 Fluid, TSL, 8 ounce bottle

20 oz cartridge feed with mounting post 1 gallon pail Ram and transfer pump 5 gallon pail cover with diaphragm pump 5 gallon pail cover diaphragm pump and

agitator 5 gallon pail cover and 5:1 transfer pump 5 gallon pail cover, 1:1 pump with dip

tube for moisture sensitive materials 5 gallon single post Ram with 11:1 pump,

mild steel 5 gallon single post Ram with 11:1 pump,

stainless steel None

hose, stainless steel fittings

313876M 9

Accessories

Mixer Kits with Shroud

Part Description

964034 Mixer, Kit, 3/16 in. (4.8mm) x 24, 10

taper tip mixers with shroud

964032 Mixer, Kit, 3/16 in. (4.8mm) x 32, 10

taper tip mixers with shroud

964028 Mixer, Kit, 3/16 in. (4.8mm) x 32, 10

Luer Lock tip mixers with shroud/sleeve

964033 Mixer, Kit, 1/4 in. (6.5mm) x 24, 10

taper tip mixers with shroud

964029 Mixer, Kit, 1/4 in. (6.5mm) x 24, 10 Luer

Lock tip mixers with shroud/sleeve

964030 Mixer, Kit, 1/4 in. (6.5mm) x 32, 10 Luer

Lock tip mixers with shroud/sleeve

964031 Mixer, Kit, 1/4 in. (6.5mm) x 48, 10 Luer

Lock tip mixers with shroud/sleeve

Mixer Packs

Part Description

964027 Mixer, 1/8 in. (3.2mm) x 24 Luer Lock

inlet/tip, 10 Pack

16D962 Mixer, 1/8 in. (3.2mm) x 24 Luer Lock

inlet/tip, 50 Pack

16D963 Mixer, 1/8 in. (3.2mm) x 24 Luer Lock

inlet/tip, 250 Pack

16D978 Mixer, 3/16 in. (4.8mm) x 24 taper tip,

50 Pack

16D979 Mixer, 3/16 in. (4.8mm) x 24 taper tip,

250 Pack

LC0077 Mixer, 3/16 in. (4.8mm) x 32 taper tip,

50 Pack

LC0084 Mixer, 3/16 in. (4.8mm) x 32 taper tip,

250 Pack

LC0082 Mixer, 3/16 in. (4.8mm) x 32 Luer Lock

tip, 50 Pack

LC0089 Mixer, 3/16 in. (4.8mm) x 32 Luer Lock

tip, 250 Pack

LC0078 Mixer, 1/4 in. (6.5mm) x 24 taper tip

mixer, 50 Pack

LC0085 Mixer, 1/4 in. (6.5mm) x 24 taper tip

mixer, 250 Pack

LC0083 Mixer, 1/4 in. (6.5mm) x 24 Luer Lock

tip, 50 Pack

Part Description

LC0090 Mixer, 1/4 in. (6.5mm) x 24 Luer Lock

tip, 250 Pack

16D968 Mixer, 1/4 in. (6.5mm) x 32 Luer Lock

tip, 50 Pack

16D969 Mixer, 1/4 in. (6.5mm) x 32 Luer Lock

tip, 250 Pack

16D970 Mixer, 1/4 in. (6.5mm) x 48 Luer Lock

tip, 50 Pack

16D973 Mixer, 1/4 in. (6.5mm) x 48 Luer Lock

tip, 250 Pack

10 313876M

O-Rings and Seals

Accessories

Part Description

24E247 Kit, O-ring, chemical resistant, PD44

24E248 Kit, Seal, Spool, H.V., PD44

24E249 Kit, Seal, Spool, L.V., PD44

16B265 Seal, Posipack, 1.25, ZAP

16B266 Seal, Posipack, 1.38, ZAP

16B267 Seal, Posipack, 1.50, ZAP

16B268 Seal, Posipack, 1.63, ZAP

16B269 Seal, Posipack, 1.75, ZAP

16B270 Seal, Posipack, 2.00, ZAP

16B271 Seal, Posipack, 2.13, ZAP

16B272 Seal, Posipack, 2.25, ZAP

16B273 Seal, Posipack, 2.38, ZAP

16B274 Seal, Posipack, 2.50, ZAP

16B275 Seal, Posipack, 2.63, ZAP

16B276 Seal, Posipack, 2.75, ZAP

16B277 Seal, Posipack, 3.00, ZAP

16B278 Seal, Posipack, 3.13, ZAP

16B279 Seal, Posipack, 3.25, ZAP

16B280 Seal, Posipack, 3.38, ZAP

16B281 Seal, Posipack, 3.50, ZAP

16B282 Seal, Posipack, 3.63, ZAP

16B283 Seal, Posipack, 3.75, ZAP

16B284 Seal, Posipack, 4.00, ZAP

16B285 Seal, Posipack, 4.25, ZAP

Part Description

16B286 Seal, Posipack, 4.50, ZAP

16B287 Seal, Posipack, 4.63, ZAP

16B288 Seal, Posipack, 4.75, ZAP

16B289 Seal, Posipack, 4.88, ZAP

16B290 Seal, Posipack, 5.00, ZAP

16B291 Seal, Posipack, 5.13, ZAP

16B292 Seal, Posipack, 5.25, ZAP

16B293 Seal, Posipack, 5.50, ZAP

16B294 Seal, Posipack, 5.75, ZAP

16B295 Seal, Posipack, 6.00, ZAP

16B296 Seal, Posipack, 6.13, ZAP

16B297 Seal, Posipack, 6.25, ZAP

16B298 Seal, Posipack, 6.38, ZAP

16B299 Seal, Posipack, 6.50, ZAP

16B300 Seal, Posipack, 6.63, ZAP

16B301 Seal, Posipack, 6.75, ZAP

16B302 Seal, Posipack, 7.00, ZAP

16B303 Seal, Posipack, 7.25, ZAP

16B304 Seal, Posipack, 7.50, ZAP

16B305 Seal, Posipack, 7.63, ZAP

16B306 Seal, Posipack, 7.75, ZAP

16B307 Seal, Posipack, 7.88, ZAP

16B450 Seal, Posipack, 8.00, ZAP

Needles

Part Description

E4000025-50 Needle, Luer Lock, Sampler Package

(10 each 14 ga x 1/2 in., 16 ga x 1/2 in., 18 ga x 1/2 in., 20 ga x 1/2 in., 22 ga x 1/2 in.)

E4000001-50 Needle, Luer Lock, 14 Gauge x 1/2 in.,

50 Pack

E4000004-50 Needle, Luer Lock, 15 Gauge x 1/2 in.,

50 Pack

E4000005-50 Needle, Luer Lock, 16 Gauge x 1 in.,

50 Pack

313876M 11

Part Description

E4000006-50 Needle, Luer Lock, 18 Gauge x 1 in.,

50 Pack

E4000011-50 Needle, Luer Lock, 22 Gauge x 1/2 in.,

50 Pack

E4000014-50 Needle, Luer Lock, 14 Gauge x 1 in.,

50 Pack

E4000024-50 Needle, Luer Lock, 23 Gauge x 1/2 in.,

50 Pack

E4000088-50 Needle, Luer Lock, 16 Gauge x 1/2 in.,

50 Pack

Grounding

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

Metering valve: attach ground wire from grounding lug to true earth ground. See Component Identification starting on page 13.

Fluid hoses: use only electrically conductive hoses.

Feed system components: attach ground wire from

grounding lug to true earth ground. See feed system manual for grounding points. See Related Manuals on page 3.

Fluid supply container: follow local code.

Solvent pails used when flushing: follow local code.

Use only conductive metal pails, placed on a grounded surface. Do not place the pail on a nonconductive surface, such as paper or cardboard, which interrupts grounding continuity.

Overview

This plural component meter, mix, and dispense device accurately meters liquid and semi-paste materials.

The machine is ideal for a two-component application requiring very small and precisely mixed shots.

The ratio of the pneumatic cylinder area to pump shaft area provides the adjustable pressure intensification needed to move the separate liquids through the mixer with a flow rate suitable for production requirements.

The complete system is enclosed. Mixing of the two materials takes place only in the mixer at the final stage of metering valve operation. See Sequence of Opera- tion on page 24.

12 313876M

Component Identification

Typical System Configurations

Base Unit

Component Identification

A Side Feed

Liquid Control Corp.

8400 PORT JACKSON AVE. N.W. NORTH CANTON, OH 44720 USA

SERIAL NUMBER

10 56 9078234

MODEL NUMBER

B Side Feed

WARNING

Do Not service without removing air pressure and waring saftey glasses.

Controls

PUSH TO

LOCK PULL TO RELEASE

B Side Feed

Base Unit

Controls

CONTROL POWER

Liquid Control Corp.

8400 PORT JACKSON AVE. N.W. NORTH CANTON, OH 44720 USA

MODEL

SERIAL

NUMBER

FIG. 1

313876M 13

+ 29 hidden pages