Page 1
INSTRUCTIONS-PARTS LIST
309042
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
24-Gallon (90-Liter)
Oil Acet
Pressurized Oil Drain
Model 115599, Series A
Rev. A
First choice when
quality counts.t
Table of Contents
Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly and Operation 4. . . . . . . . . . . . . . . . . . . . . . . .
Parts List and Drawing 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Phone Number 8. . . . . . . . . . . . . . . . . . . . . . . . . . .
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
ECOPYRIGHT 1999, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
9426A
Page 2
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals before you operate this equipment.
D Use the equipment only for its intended purpose. If you are not sure, contact your Graco
distributor.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
D Do not alter or modify this equipment.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D This equipment is intended for collection of petroleum lubricants or antifreeze only. Any other use
or collection of any other fluids could result in damage to the equipment or serious bodily injury.
D Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and
solvent manufacturer.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Dispose of waste fluids according to all local, state, and national guidelines.
FIRE AND EXPLOSION HAZARD
Poor ventilation, open flames, or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.
D Do not exceed 8 psi (0.5 bar, 50 kPa) air supply pressure.
D Do not tamper with air relief valve setting.
D If you are using this unit with an evacuation system, make sure the pumping system is installed
and grounded according to the manufacturer’s recommendation.
D Provide fresh air ventilation to avoid the buildup of flammable fumes.
D Extinguish all open flames in the work area.
D Do not smoke in the work area.
2 309042
Page 3
WARNING
X – Do not drain caustic or flammable products.
Y – Do not expose the tank to any source of heat.
Z – Do not do any welding on the tank.
W – While draining high temperature oils, keep hands and face protected.
United States Government safety standards have been adopted under the Occupational Safety and Health Act.
You should consult these standards–particularly the General Standards, Part 1910.
309042 3
Page 4
Assembly and Operation
B
A
C
H
F
E
L
D
M
G
8 psi (0.5 bar,
50 kPa)
H
G
4 309042
Page 5
Assembly and Operation
ASSEMBLY
1. Fig. 1. Insert handle into holding fixtures provided
on tank and secure it with screws. Place tool tray
A on bracket provided. Attach hose retainer B.
2. Fig. 2. Attach drain column C to drain basin and
tighten it with suitable wrench.
3. Fig. 3. Connect drain assembly to tank by tightening ring nut E with suitable wrench.
4. Fig. 4. Attach hose F with hose clamp provided.
5. Fig. 5. Close red handled ball valve G by turning it
clockwise.
OPERATING DRAIN
CAUTION
S Fig. 6. When draining fluids into the catch
basin, avoid automatic closing of the bleeder
vent on the funnel by leaving 1.5 to 2 in.
(4–5 cm.) clearance from upper limit funnel
extension.
S Fig. 7. The oil level gauge H located on the
side of the tank indicates the quantity of oil
drained. Never fill the tank over the maximum
level indicated by the gauge
1. Fig. 6. To raise and lower funnel, loosen ring nut M
and hand tighten after reaching desired height.
EMPTYING DRAIN
CAUTION
Before emptying the tank, lift the funnel to its upper
limit so that the safety air bleeder vent is automatically closed.
1. Fig. 7. Close red handled ball valve L.
2. Attach end of drain hose to suitable waste oil
container.
3. Connect 8 psi (0.5 bar, 50 kPa) shop air to valve D
and open ball valve G.
4. After fluids have been transferred from unit’s tank
close ball valve G.
Note: Unit is equipped with pneumatic safety relief
valve that has been factory calibrated at 14 psi (1 bar,
100 kPa).
309042 5
Page 6
Parts List and Drawing
Oil Ace Pressurized Oil Drain, Model 115599, Series A
part numbers in illustration locate repair kits listed on page 7.
Note:
2
242039
242032
(242033)
6
3
7 (242034)
242037
242035
242042
242036
5 (242033)
4
1
242041
242038
242031
Ref.
No. Part No. Description Qty.
1 242029 TANK, oil receiver 24 gal. (90 liter) 1
2 242064 FUNNEL, oil receiver 1
3 115572 HANDLE 1
4 115573 TRAY 1
6 309042
242030
9426A
Ref.
No. Part No. Description Qty.
5 115574 NUT, ring 1
6 115576 VALVE, ball 1
7 115577 VALVE, relief 1
Page 7
Repair Kits
Oil Ace Pressurized Oil Drain Repair Kits
Part No. Description
242030 REPAIR KIT, swivel wheel
242031 REPAIR KIT, fixed wheel
242032 REPAIR KIT, bowl
242033 REPAIR KIT, upper valve
242034 REPAIR KIT, air valve
242035 REPAIR KIT, discharge hose
242036 REPAIR KIT, dispense valve
Technical Data
Length 21 in. (533 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Width 16 in. (406 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Height
with bowl at lowest adjustment 55 in. (1397 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
with bowl at highest adjustment 75 in. (1905 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Funnel Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 in. (584 mm)
Dry Weight 74 lb (33.6 kg). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wetted parts linear low-density polyethylene (LLDPE), zinc-plated steel,. . . . . . . . . . . . . . . .
Recommended operating temperature 30_ to 105_ F (–1_ to 41_ C). . . . . . . . . . . . . . . . . . . .
Part No. Description
242037 REPAIR KIT, screw
242038 REPAIR KIT, gauge tube
242039 REPAIR KIT, funnel
242040 REPAIR KIT, o–ring (not shown)
242041 REPAIR KIT, union fitting
242042 REPAIR KIT, intake valve
brass, nylon, polypropylene, PVC
309042 7
Page 8
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warrant y does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property , o r a ny
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty , and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1–800–533–9655 Toll Free
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Foreign Offices: Belgium, England, Korea, France, Germany, Hong Kong, Japan
Sales Offices: Minneapolis, Detroit
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
www.graco.com
PRINTED IN USA 309042 October 1999
8 309042
Loading...