Good Will GPI-826, GPI-825, GPT-815, GPT-805 User Manual
ELECTRICAL SAFETY TESTER
Y
Y
–
USER MANUAL
WARNING
MANUFACTURER ASSUMES NO L IABILIT
IF UNIT OPERATED IN AN UNSAFE
MANNER.
WARNING
THIS INSTRUMENT GENERATES AND
DELIVERS A HAZARDOUSLY HIGH
VOLTAGE (5kV). BE EXTREMEL
CAREFUL WHEN USING THIS
INSTRUMENT. BE SURE TO READ
MANUAL SECTION 3 PRECAUTIONS
ELECTRICAL SAFETY TESTER
USER MANUAL
EC Declaration of Conformity
We
GOOD WILL INSTRUMENT CO., LTD.
No.7-1, Jhongsing Road, Tucheng City, Taipei County 236, Taiwan
GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.
No. 69 Lushan Road, Suzhou New District Jiangsu, China.
declares that the below mentioned product
are herewith confirmed to comply with the requirements set out in the Council
Directive on the Approximation of the Law of Member States relating to
Electromagnetic Compatibility (89/336/EEC,92/31/EEC) and Low Voltage
Equipment Directive (73/23/EEC, 93/68/EEC).
For the evaluation regarding the Electromagnetic Compatibility and Low Voltage
Equipment Directive, the following standards were applied:
EN 61326-1: Electrical equipment for measurement, control and laboratory use –
EMC requirements (1997+A1: 1998+A2:2001)
Conducted and Radiated Emissions
EN 55011 Group I class A: 1998
Current Harmonic
EN 61000-3-2: 2000
Voltage Fluctuation
EN 61000-3-3: 1995
----------------------------------------------
----------------------------------------------
----------------------------------------------
----------------------------------------------
GPT-805/815, GPI-825/826
Electrostatic Discharge
EN 61000-4-2: 1995+A1 :1998
Radiated Immunity
EN 61000-4-3: 1996+A1 :1998
Electrical Fast Transients
EN 61000-4-4: 1995
Surge Immunity
EN 61000-4-5: 1995
Conducted Susceptibility
EN 61000-4-6: 1996
Power Frequency Magnetic Field
IEC 61000-4-8: 1993
Voltage Dips/ Interrupts
EN 61000-4-11: 1994
Low Voltage Equipment Directive 73/23/EEC & amended by93/68/EEC
Safety Requirements IEC/EN 61010-1: 2001
Remark: Also complied with Continuity of Protective Bonding Tester, Insulation
Resistance T est, Voltage Test, and Residual Voltage Test in accordance with
the Sub-Clauses 19.2, 19.3, 19.4 and 19.5 of EN 60204-1: 1997
i
ii
ELECTRICAL SAFETY TESTER
USER MANUAL
ELECTRICAL SAFETY TESTER
USER MANUAL
CONTENTS PAGE
1. PRODUCT INTRODUCTION............................................
1-1.Description…………………………..………………….
1-2.Feature……………………………..……………………
2. SPECIFICATION………………………………………….. 3
3. PRECAUTIONS BEFORE OPERATION……...………...
3-1.Unpacking the instrument……..…………….………...
3-2.Checking the Line Voltage..…………………..………..
3-3.Environment……………………………………..……..
4. PANEL INTRODUCTION……………………..………….
4-1.Front Panel……………………………………………...
4-2.Rear Panel……………………………………….……...
5. OPERA T IO N METHO D…… ..……………………………
5-1.AC Withstanding Test………………………………….
5-2.DC Withstanding Test…….……………………………
5-3.Insulation Test…………...…..………………………….
6. MAINTENANCE………..………………………………….
6-1.Fuse rating and type.…………………………………...
6-2.Cleaning………………..………………………………..
11
12
13
13
14
16
17
17
17
1
1
2
6
6
6
8
9
SAFETY TERMS AND SYMBOLS
These terms may appear in this manual or on the product:
WARNING. Warning statements identify condition or
practices that could result in injury or loss of life.
CAUTION. Caution statements identify conditions
or practices that could result in damage to this
product or other property.
The equipment shall not be used for measurements
within category II, III and IV.
The following symbols may appear in this manual or on
the product:
iii
DANGER ATTENTION Protective Earth (ground) Frame or
High Voltage refer to Manual Conductor Terminal Chassis
Terminal Terminal
iv
ELECTRICAL SAFETY TESTER
USER MANUAL
ELECTRICAL SAFETY TESTER
USER MANUAL
FOR UNITED KINGDOM ONLY
NOTE: This lead/appliance must only be wired by competent
persons
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in accordance
with the following code:
Green/ Yellow: Earth
Blue: Neutral
Brown: Live (Phase)
As the colours of the wires in main leads may not correspond
with the colours marking identified in your plug/appliance,
proceed as follows:
The wire which is coloured Green & Yellow must be connected
to the Earth terminal marked with the letter E or by the earth
symbol
or coloured Green or Green & Yellow.
The wire which is coloured Brown must be connected to the
terminal marked with the letter L or P or coloured Brown or
Red.
If in doubt, consult the instructions provided with the equipment
or contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on
the equipment and/or user instructions for details. As a guide,
cable of 0.75mm
2
should be protected by a 3A or 5A fuse. Larger
conductors would normally require 13A types, depending on the
connection method used.
Any moulded mains connector that requires removal
/replacement must be destroyed by removal of any fuse & fuse
carrier and disposed of immediately, as a plug with bared wires
is hazardous if a engaged in live socket. Any re-wiring must be
carried out in accordance with the information detailed on this
label.
The wire which is coloured Blue must be connected to the
terminal which is marked with the letter N or coloured Blue or
Black.
v
vi
ELECTRICAL SAFETY TESTER
USER MANUAL
ELECTRICAL SAFETY TESTER
USER MANUAL
1. PRODUCT INTRODUCTION
1-1. Description
The GPT/GPI-800 Electrical Safety Testers (EST) are designed for
AD/DC Withstanding Voltage test and Insulation Resistance test (IR) in
order to provide a safe and accurate test environment for the operator.
With thoughtful design described in 1-2. Feature insures a safe operation
environment of high voltage test to protect user from hazardous impact.
The Electrical Safety Testers comply with the requirement of the
electrical equipment & appliance control ordinances and JIS, CSA, UL,
BS and other overseas standards as well. The testers can be used for
withstanding voltage test of the various types of electrical and equipment
and components.
The GPT/GPI-800 series are based on the family of GW
withstanding voltage tester including AC Withstanding Voltage test, DC
Withstanding Voltage test and Insu lation Resistance test. Please refer to
the table as follows:
Function
Model
GPT-805 (500VA)
GPT-815 (500VA)
GPI-825 (500VA)
GPI-826 (100VA)
AC DC IR
ˇ
ˇˇ
ˇˇ
ˇˇ
1-2. Features
The GPT/GPI-800 series offer several other features :
1) Current and output voltage setting
A safe way to set the current and output voltage without high
voltage activated.
2) Easily and quickly setting with front panel control
A user-friendly interface provides user an easy and quick way to
set all parameters.
3) Testing time
Use micro processor to control testing time.
4) Adjustable ARC detect level
The ARC detect level can be adjusted with front panel control.
5) Adjustable output voltage during test
The output voltage can be adjusted during testing that add an
operation flexibility.
6) An alert indicator for high voltage
A flashing red LED indicates dangerous situation during high
voltage output is activated.
7) Remote I/O controller
In addition to the 9 pin remote I/O controller to control
START/RESET, it also provides PASS/FAIL/TEST signal for
professional use.
1
2
Loading...