Instructions on this manual describe the controls of the DVD Recorder. You can also use the remote
controller controls with the same name as those on the unit.
Dear Customers
We would like to thank you for purchasing this DVD+R/RW and DVD-R/RW Recorder with built-in FreeView
Digital Terrestrial Receiver.
We strongly recommend that you carefully study the operating instructions before attempting to operate the
unit and that you note the listed safety precautions.
3
IMPORTANT SAFEGUARDS
4
SAFETY INFORMATION
WARNING
LASER PRODUCT
CAUTION
LASER CLASS 1
CLASS 1
Wave Length: 650 nm ±15nm (DVD)
Maximum output of accessible laser radiation: < 0,39 mW (continuous wave)
Classified according to IEC 60825-1: 1993 + A1 : 1997
790 nm ±15nm (CD)
This unit is a class 1 laser product. However this product uses a visible laser beam which could cause
hazardous radiation exposure.
Be sure to operate the recorder correctly as instructed.
While this recorder is plugged to the wall outlet, do not place your eyes close to the opening of the disc tray
or other openings to look inside the recorder for your own safety.
Use of performance control or adjustment procedures other than those specified may result in hazardous
radiation exposure. Do not open the covers and do not attempt to repair any damaged parts. Please refer to
a service technician or qualified personnel for any necessary repairs.
WARNING
To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
To reduce the risk of fire or electric shock, and any interference, use the recommended accessories only.
Do not move your device for 20 seconds after removing AC power to ensure that the actuator is completely
locked. This helps prevent the media and the heads from accidental damage due to vibration, moving or
shipping.
This recorder must not be exposed to dripping or splashing with liquids, such as vases, shall be
placed on the recorder.
CAUTION
Danger of explosion if the remote control battery is incorrectly replaced. Replace only with the same
or equivalent type.
“This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.”
Manufactured under license from Dolby Laboratories,
"Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
5
GENERAL PROPERTIES
1. DVD+R/RW, DVD Video, DVD-R/RW, Audio CD, (S)VCD, CD-R/RW, , JPEG playback, DVD+R/RW and
DVD-R/RW Dual Media recording
2. Integrated FreeView Digital Terrestrial Receiver
3. Low power standby mode support
4. User-friendly OSD menu control
5. Vacuum Fluorescent Display (VFD)
6. NTSC/PAL playback (according to disc content) and recording
7. Recording in different qualities (HQ, SP, LP, EP, SLP)
8. One Touch Recording
9. Auto title menu with thumbnail index pictures
10. Finalize for DVD+R and DVD-R/ DVD-RW disc
11. 7 Day Electronic Program Guide (EPG)
12. Adding chapter markers
13. Appending, overwriting, deleting titles
14. Recording with timer
15. Dolby Digital, LPCM audio via coaxial digital audio output
16. Multiple Aspect Ratio support (16:9 Widescreen, 4:3 Letterbox, 4:3 PAN&SCAN)
17. Multi-Audio (up to 8) support (According to disc content) (For DVD)
18. Multi-Subtitle (up to 32) support (According to disc content) (For DVD)
19. Multi-Angle (up to 9) support (According to disc content) (For DVD)
20. 8 level parental control
21. Fast forward and rewind in 5 different speeds (2x, 4x, 8x, 16x, 32x Fast Forward/Backward)
22. For DVD / (S)VCD; frame by frame forward playback
23. For DVD / (S)VCD; slow forward playback (1/2x, 1/4 x, 1/8x Slow Forward)
24. Maximum 5K*5K resolution for baseline, 1280*1024 resolution for progressive JPEG playback
28. Different play modes for Audio CD and (Normal/Random/Intro)
29. Program function for Audio CD, , JPEG and MPEG
30. Simultaneous playback of audio and pictures
31. 10 timer recording events
32. Pause recording
33. A → B repeat
34. Aerial Antenna input / output (loop through)
35. 2 SCART socket
36. Composite Video input/output
37. S-Video input
38. Coaxial Digital Audio output
CONTENTS
1 X REMOTE CONTROL WITH 2X AAA BATTERIES
1X SCART TO SCART CABLE
1 X DVD RECORDER
1X INSTRUCTION MANUAL (You are reading it).
1x Detachable mains cable with fitted mains plug.
1x Aerial Loop Through cable.
6
NOTES ON CD-R/RW, DVD-R/RW AND DVD+R/RW DISCS
• CD-R, DVD-R, DVD+R (Recordable) and CD-RW, DVD-RW, DVD+RW (Rewritable) discs, recorded
by the users, may only be used after finalization process.
• CD-R/RW, DVD-R/RW and DVD+R/RW discs may not be usable, depending on the disc features,
recording conditions and damage or dirt on disc. The disc configuration and features are determined
by the tool and device used for recording. Therefore, users may face with the following undesired
consequences:
§ Some discs may not be read at all
§ Some discs may cause system crash after laying for a while
§ Some parts of the disc may be skipped or worked abnormally
• Compare with the original discs, the time passed for reading a CD-R/RW, DVD-R/RW and
DVD+R/RW discs may be longer.
• This DVD player may not support some recordings due to differences in recording formats or disc
type.
• Please read the user’s manual playback.
• CD-R/CD-RW discs recorded by CD-DA method can be played. Some CD-R/CD-RW disc may be
incompatible due to laser pick-up and disc design.
• DVD-R discs recorded by DVD-Video method can be played. Some DVD-R discs may be
incompatible due to laser pick-up and disc design.
•Some discs may be incompatible with JPEG Viewer function due to different recording format or
condition of the disc.
7
SAFETY PRECAUTIONS
Power Source
The unit should be operated only from a 220-240V~ 50 Hz outlet. Please do not open the cover. There is
high voltage in the set, which will endanger your life. Please contact local service agent for help and advice.
Repairs to be carried out by a qualified technician only.
• The apparatus is not disconnected from the AC power source (mains) as long as it is connected to the
wall outlet, even if the apparatus itself has been turned off.
• If you are not going to use the apparatus for a long time, be sure to disconnect the apparatus from the wall
outlet.
IMPORTANT NOTE: The voltage markings and other safety markings are found on the underside of the
appliance.
Power Cord
Do not place the unit, a piece of furniture, etc., on the power cord (mains lead), or pinch the cord. Handle
the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord
when your hands are wet as this could cause a short circuit or electric shock. Never make a knot in the cord
or tie it with other cords. The power cords should be routed in such a way that they are not likely to be
stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord
once in a while. When you find it damaged, ask closest service agent for help. When the AC power cord
needs to be changed, it should be done at a qualified service shop only.
Choice of Location
• Please do not place the set in a place subject to direct sun light, excessive dust or mechanical shock or in
a location near heat sources.
• The set should be placed on a solid and safe base. Do not place the apparatus on a soft surface such as
a rug that might block the ventilation holes on the bottom.
• A location should not be selected such as a room with high humidity, as the condensation, arising in the
kitchen for example, may cause malfunction or damage the set.
• Heating or other thermal radiation under the set also may cause malfunction or damage the set.
• The hot air, which arises during the operation, should be ventilated with sufficient air circulation. Please do
not put the set into closed areas and do not cover it.
• Please avoid the contact of the set with water or humidity. Do not put into operation near bath, swimming
pools.
• Take care to provide a good air circulation. Place the apparatus in a location with adequate ventilation to
prevent heat build-up in the apparatus.
• Should any solid object or liquid fall into the cabinet, unplug the apparatus and have it checked by
qualified personnel before operating it any further.
8
NOTES ON DISCS
BENZENE
Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in
direct sunlight as the temperature can rise quickly and damage the disc.
On handling discs:
• To keep the disc clean, handle the disc by its edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
• If the disc is contaminated with any substance, like glue remove before using it.
On cleaning:
• Before playing, clean the disc with a cleaning cloth. Wipe the disc from the inside to the outside.
• Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended
for vinyl LPs.
Discs that should not be used:
Only the discs including the marks (see 1.7) can be played.
Note, however, that discs with special shapes (heart-shaped discs, hexagonal discs, etc.) cannot be played.
Do not attempt to play such discs, as they may damage the unit.
NOTE:Do not use record spray or antistatic. Also do not use volatile chemicals such as benzene or thinner.
RECORD
SPREY
THINNER
9
CONNECTION
ANTENNA CONNECTION
VIDEO & AUDIO OUTPUT SOCKETS
(C)able not
supplied
(C)able not
supplied
10
ANALOG AUDIO CONNECTION
DIGITAL AUDIO CONNECTION
(C)able not
supplied
(C)able not supplied
11
SCART CONNECTION
(Scart Cable
supplied)
(C)able not supplied
Connect Camcorder to the Front Sockets of DVD Recorder
12
1. INTRODUCTION
1.1 THE REMOTE CONTROL
STANDBYOPEN/CLOSE
ABC
DEF
GHI
123
JKL
MNO
PQR
PROGRAM
456
VWX
STU
YZ
789
SEARCH
MODE
ADD/CLEAR
VOLUME
0
RETURN /EXITHDD/DVD
SELECT
SETUPTV/DVD
VIDEO SOURCEWATCH TVFUNCTION
+
-
+
-
NOTE: HDD/DVD button
not used on this model.is
RECORD/DUBPLAY/PAUSESTOP
SKIPSEARCH
TIMERINSER T
PLAY
MODE
TITLE
GUIDE
SUBTITLEAUDIOANGLE
REC MODEFAV
CHP.
REPEATZOOMA - B
DISPLAY
INFO
TEXTMENU
WIDE
MUTE
13
STANDBY : To switch the set ON or OFF.
OPEN/CLOSE : To Open/close the disc tray.
PLAY MODE / RED : For , CD-DA, JPEG and MPEG tracks switches between play modes. In FreeView
mode move up a page through channel list. It is used to select RED option in digital
Teletext.
ZOOM /BLUE : Enlarge the image. In FreeView mode move down a page through channel list. Move to
bottom in EPG program details. It is used to select BLUE option in digital Teletext.
REPEAT / GREEN : To play titles, chapters and tracks repeatedly. In FreeView mode, scroll up through EPG
program details. It is used to select GREEN option in digital Teletext.
A-B / YELLOW : Repeat a selection from point A to point B. In FreeView mode, scroll down through EPG
program details. It is used to select YELLOW option in digital Teletext.
TITLE / GUIDE : If DVD supports, to choose the title menu in DVD discs. Display and exit EPG in
FreeView mode.
DISPLAY/ INFO : Opens Display menus. Opens Display menu Help in FreeView mode.
TEXT : Start and stop digital text.
MENU : Displays the DVD or (S) VCD menu. In FreeView mode, displays FreeView system
menu.
SETUP : It opens and closes the system-menu.
RETURN / EXIT : Returns to previous menu on a video CD. Also for CD Menu and Setup menu, it returns
to the upper folder. In FreeView mode, exits from EPG menu.
WATCH TV : To switch to monitor mode.
SELECT : Select function/value.
ARROW KEYS
(3/4/5/6) : To navigate inside menus. Left/right arrow keys are used for volume up/down in
freeview mode (when digital teletext is not active).
PLAY/PAUSE (►/;) : Playback a disc. If this key is pressed during playback or recording, operation is
paused. Also use this key to switch to disc playback from the beginning in monitor mode.
For any DVD title that has a root menu with still picture, this key functions as “button
select” (selects highlighted item) in the root menu. Otherwise this functioning of
“play/pause” key on the root menu will be prohibited by the disc, and will appear.
STOP (■) : Stop playback/recording.
SKIP (9) : Press this key during playback: Previous chapter/ film or previous file.
SKIP (:) : Press this key during playback: Next chapter/ film or next file. Press this key during
pause mode: Shows next frame at each press.
SEARCH (►►) (◄◄) : Fast forward and fast backward in x2, x4, x8, x16 and x32. Slow forward in Pause state.
REC MODE : Select quality and duration of recording.
TV/DVD : Enables/disables the SCART socket output to the TV set. This lets you watch another
program via TV set while DVD recorder is recording another program or source without
unplugging the SCART cable.
RECORD/DUB : Records the selected video source or start dubbing and resumes paused recording.
Activates One-Touch-Recording while recording is in progress.
INSERT CHAPTER : Inserts a chapter manually to recording media during recording.
SUBTITLE : If DVD supports, changes the subtitle language, turns it on or off. Also used to switch
DVB subtitles on and off if the channel provider supports.
VIDEO SOURCE : Switches the video source in the order of FreeView Input, SCART Input, Front CVBS,
Front S-Video and Disc
AUDIO : If DVD supports, switches between audio formats during DVD playback. Also used to
change DVB audio language if the channel provider supports.
ANGLE/WIDE : Selects the angle to view the scene. This only works when multiple angles are provided
for a scene. Selects screen format in FreeView mode.
TIMER : To program a recording or to alter/clear pre-programmed recordings.
NUMERIC KEYS (0- 9) : 0 - 9. Also used for channel rename in FreeView mode.
ADD/CLEAR : Add files to make playlist in PROGRAM play mode, remove files from playlist. Also
erases the number you previously entered.
PROGRAM+ : Tunes to next program while watching TV.
PROGRAM- : Tunes to previous program while watching TV.
SEARCH MODE : Press to move to any desired title/chapter/track/time within the disc.
HDD/DVD : This function is not available on this non HDD model.
FUNCTION : Opens Functions menu.
V+ : Increases volume
V- : Decreases volume
MUTE : Mutes function.
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.