website:http://us.lgservice.com
MICROWAVE OVEN
INSTALLATION INSTRUCTIONS
PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS.
MV1604ST
P/NO.: 3828W5U0435
– 2 –
Your Safety First
BEFORE YOU START
• Proper installation is the installer's responsibility!
– Read the entire manual before you begin. The model number label is located on the oven front.
See Figure 1. The mounting plate is located on back side of microwave oven. See Figure 2.
NOTE: Vent grille appearance varies by model.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly.
• Avoid Electrical Shock!
– Before you drill into the wall, note where electrical outlets are and where electrical wires might be concealed
behind the wall. YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires with your drill bit.
– Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
• ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.
– You need a DEDICATED 120V, 60Hz, AC only, 15 or 20A, fused electrical supply (located in the cabinet
above the microwave as close as possible to the microwave) serving only the microwave.
Model Number Plate
Mounting Plate
Figure 1 Figure 2
For Your Safety
WARNING
– 3 –
Your Safety First
• THIS APPLIANCE MUST BE GROUNDED!
– If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape
wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding
plug.
• Place the plug into a properly installed and grounded outlet. See Figure 3.
• Do not use an extension cord.
• Keep the power cord dry and do not pinch or crush it.
• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE
POWER SUPPLY CORD GROUNDING PRONG!
This appliance MUST be grounded!
Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not
completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.
SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!
– DO NOT try to operate the microwave oven with the door open.
– DO NOT tamper with or defeat the safety interlocks.
– DO NOT place objects between the microwave oven front face and the door.
– DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
– DO NOT operate the microwave oven if it is damaged.
– The microwave oven door must close properly to operate safely.
– DO NOT USE THE MICROWAVE OVEN:
• If the door is bent.
• If the hinges or latches are broken or loose.
• If the door seals, sealing surfaces or glass is broken.
– DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!
It should be adjusted and repaired by a qualified technician who can check for microwave leakage after
repairing the oven.
PROPERLY POLARIZED AND
GROUNDED OUTLET
Three-Pronged (Grounding) Plug
Figure 3
If you use the grounding plug improperly, you risk electric shock and/or fire!
WARNING
Improper grounding could result in electric shock, fire or other personal injury.
WARNING
If you do not use the microwave oven as instructed,
you could be exposed to excessive microwave energy.
WARNING
– 4 –
Your Safety First
• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.
– Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of
minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
– ATTACH (See note on page 5) of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.
– DO NOT mount the microwave oven to an island or peninsula cabinet.
– BE SURE the upper cabinet and rear wall structures can support 150 lbs., plus the weight of any
items you place inside the oven or upper cabinet.
– Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
– BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.
CAUTION
• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY
MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result in property damage.
30" min. cabinet opening width
30" min. clearance from bottom
of cabinet to cooking surface
or countertop before installation.
Grounded Outlet
(inside upper cabinet)
Power Supply Cord Hole
(Use templates included
with installation instructions)
Figure 4
If you do not mount the oven as instructed,
you risk personal injury and/or property damage.
WARNING
– 5 –
Parts, Tools, Materials
THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
Damper/duct connector
(for roof venting or wall venting installation)
Not Actual Size (2 pieces must be assembled as
shown) Not used if venting into kitchen.
One power cord clamp and
One dark-colored mounting screw
(to hold the power cord)
Actual Size
Four 1/4" x 2" lag screws - Actual Size
(for wall stud holes)
Four 1/4" x 3" toggle bolts - Actual Size
(for drywall holes)
Two 1/4" x 3" bolts - Actual Size
(for securing to the upper cabinet)
Two 1/4" x 3" bolts - Actual Size
(for securing to the upper cabinet)
Two tapping screws - Actual Size
(for attaching the damper duct connector)
One upper cabinet template- Not Actual Size
12
4
REAR WALL TEMPLATE
CAUTION — IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
LINE UP WITH
PREVIOUSLY
DRILLED HOLE
B.
LINE UP WITH
PREVIOUSLY
DRILLED HOLE
A.
Printed in Korea
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the wall venting
cutout. Do not use this template for roof
or room venting.
1.Place the template flat against the rear
wall, aligning circles A and B with the
corresponding holes previously drilled in the
rear wall for holes A and B of the wall plate.
2.With the template aligned to the holes, tape the
template to the rear wall.
3.Use a saber or keyhole saw to cut out the shaded
area F through the rear wall.
4.Remove the template from the rear wall.
5.
RETURN TO AND PROCEED WITH THE
INSTALLATION INSTRUCTIONS.
1/4
P/N. 4922W5A060A
F. CUT OUT FOR WALL
VENTED ONLY
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
One rear wall template- Not Actual Size
(3 pieces mounting plate only)
One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet)
NOTE: You need to install at least two lag screws into a 2" x 4" stud and four anchor bolts into the wall.
and the mounting area must meet the 150 lbs. weight requirement.
– 6 –
Parts, Tools, Materials
Clear Tape
(for taping the templates to the wall)
Phillips Screwdriver
(for the screws)
Pencil
Flat Blade Screwdriver
(for the toggle bolts)
Plumb Line
Measuring Tape
(metal preferred)
Duct Tape
Small Side Cutters or Tin Snips
Caulking Gun and Caulk
Stud Finder or Thin Nail
Saber Saw
(for cutting vent holes for roof
or wall vending)
Keyhole Saw (for the power cord hole)
You will need the following tools and materials for the installation:
Carton or other heavy material such as a blanket for covering the counter top.
3/8" and 3/4" wood drill bits
1/2" and 3/16"
drill bits
Electric Drill
●
If you have brick or masonry walls, you will need special hardware and tools.
●
The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft damper.
(Shown on page 5).
– 7 –
STEP 1: Prepare The Electrical Connection
Improper grounding could result in electric shock or other personal injury.
1. Locate the grounded electric outlet for this oven in the
cabinet above the oven, as shown in Figure 5.
NOTE: The outlet should be on a circuit dedicated to the
microwave oven (120V, 60 Hz., AC only) with a 15 or 20A
fused electrical supply.
IMPORTANT: If you do not have the proper wall outlet,
you MUST have one installed by a qualified electrician.
2. You will cut the hole for the power supply cord (shown in
Figure 5) later when you prepare the wall and upper cabinet in
Step 4.
NOTE: Do not use an extension cord.
Keep the power cord dry and do not pinch or crush it.
DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD
GROUNDING PRONG!
This appliance MUST be grounded!
WARNING
AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!
WARNING
Upper
Cabinet
Power-Supply-Cord Hole
Figure 5
Grounded Outlet
(Inside Cabinet)
– 8 –
STEP 2: Prepare The Venting System
THIS OVEN MUST BE PROPERLY VENTED!
WARNING
NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork
fittings and length are shown in Figure 10, page 9.
You may vent your oven in one of three ways. However, do NOT vent into a wall cavity, an attic, or an unused
area.
Roof-venting If your oven is located on an outside wall near the roof, as in Figures 7 (3 1/4" x 10" duct) and
Figure 9 (6" round duct.)
Wall-venting If your oven is located on an outside wall of your house, as in Figure 6 (3 1/4" x 10" duct) and
Figure 9 (6" round duct.)
Room-venting If your oven is located on an inside wall of your house, as in Figure 8.
NOTE: If you choose the rear exhaust method (roof or wall-venting), be sure there is enough clearance within the
wall for the exhaust duct.
REMEMBER AS YOU INSTALL THE
VENTING:
Keep the length of the ductwork and the number
of elbows to a minimum to ventilate your oven
efficiently. See examples on page 9.
Keep the size of the ductwork the same.
Do not install two elbows together.
Use duct tape to seal all joints in the duct system.
Use caulking to seal the exterior wall or roof
opening around the cap.
Cabinet
Oven
Figure 6
Wall Venting
Through-the-roof
3 1/4"x10"
Duct
Roof Cap
Roof Venting
Cabinet
Oven
Figure 7
Roof Venting
Figure 8
Room Venting
6"min diameter
Round Duct
3 1/4" to Round
Duct Transition
3 1/4" to Round
Ductwork Transition
Roof Cap
Wall Cap
Elbow
Figure 9
Cabinet
Wall Cap
Oven
Wall Mounting
3 1/4"x10"
Duct
Through-the-wall Duct
– 9 –
STEP 2: Prepare The Venting System
Standard Fittings
NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension
duct installed between the damper assembly and the adapter to prevent the exhaust damper’s sticking.
Duct Length
The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must not
exceed 140 feet.
For best performance, do not use more than three 90 degree elbows, and keep the length as short as possible.
Below are the standard fittings and their equivalent length in feet.
To calculate the equivalent length of each duct piece used, see the examples below.
Figure 10
For 3 1/4" x 10" SYSTEMS
1 3 1/4” x 10” 90° elbow = 25 ft.
1 Wall Cap = 40 ft.
8 feet straight duct = 8 ft.
TOTAL LENGTH = 73 ft.
1 transition = 5 ft.
2 90° elbows = 20 ft.
1 Wall Cap = 40 ft.
8 feet straight = 8 ft.
TOTAL LENGTH = 73 ft.
For 6" ROUND SYSTEMS
3 1/4” x 10”
to 6" = 5 ft.
90˚elbow
= 10 ft
45˚elbow
= 5 ft
3 1/4” x 10”
wall cap
= 40 ft
3 1/4” x 10”
flat elbow
= 10 ft
3 1/4” x 10” roof
cap = 24 ft
3 1/4” x 10” 90˚
elbow = 25 ft
1 2 3
4 5 6 7
Examples
6ft.
2ft.
wall cap
transition
2ft.
6ft.
wall cap
– 10 –
STEP 3: Prepare The Venting Blower
Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if you
want wall-venting or room-vented (recirculating) installation.
• DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in
electrical shock.
REMOVE THE MOUNTING PLATE:
1. Remove any shipping materials and parts from inside the
microwave oven. Set them aside for later use.
2. Cover the counter top or cooktop with a thick, protective
covering to protect it from damage and dirt. See Figure 11.
NOTE: If you have a free-standing range, disconnect
it, move it onto a piece of cardboard or hardboard and
pull it away from the wall, so that you can get closer to
the upper cabinet and back wall for easier measuring
and drilling.
3. Remove mounting plate screw(s) (1 or 2 screws) from the
mounting plate as shown and discard the screws.
See Figure 12.
4. This plate will be used as the rear mounting plate. (It will be
used to locate and mark the mounting holes on the rear wall.)
5. Locate exhaust adaptor, grease filters and hardware packet.
6. At this point, remove any adhesive tape (if there is any), on the
exhaust adaptor, the grease filters and the power supply cord.
ROOF-VENTED INSTALLATION:
This oven is shipped assembled for roof-vented. You will need to
install the exhaust adaptor regardless of cabinet.
1. Attach the exhaust adaptor to the blower plate by sliding it into
the guides. See Figure 13.
A thick, protective
covering
Mounting plate
Control Panel Side
Exhaust
Adapter
Back of Oven
Mounting plate
screw(s)
(1 or 2 screws)
Mounting Plate
Control Panel Side
Mounting Plate
Screw(s)
(1 or 2 screws)
Figure 11
Figure 12
Figure 13
ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT.
WARNING
– 11 –
STEP 3: Prepare The Venting Blower
WALL-VENTED INSTALLATION:
1. Remove one blower unit mounting screw and one or
several blower plate mounting screw(s). Remove the
blower plate from cabinet. See Figure 14.
2. Carefully lift the blower unit out of the microwave oven.
3. Use side cutters or tin snips to cut and remove knockouts
B from Back plate. Discard knockouts. Be careful not to
distort the plate. See Figure 15.
4. Reassemble the blower wire. See Figure 16.
5. Rotate the blower unit so that the exhaust ports face the
rear of the cabinet. See Figure 17.
6. Place blower unit back into cabinet. Check that the exhaust
ports face towards the rear of the cabinet. Be sure the
wires are not pinched. See Figure 18.
7. Reattach the blower plate to cabinet so the exhaust ports
and blower plate opening are aligned. Attach with one
blower unit mounting screw and then one or several blower
plate mounting screw(s). See Figure 19.
Figure 14
Blower Plate
Mounting Screw
Blower Plate
Back Plate
Blower Unit
Mounting Screw
Blower Unit
Parts B
Figure 15
Parts B
Knockouts Parts B
Blower
Unit
Exhaust Ports
Figure 16
Figure 17
Figure 19
Blower Plate
Mounting Screw
Blower Plate
Back Plate
Blower Unit
Exhaust Ports
Blower Unit
Blower Plate
Mounting Screw
Figure 18
Exhaust
Ports
– 12 –
STEP 3: Prepare The Venting Blower
ROOM-VENTED (Recirculating)
INSTALLATION:
1. Remove one blower unit mounting screw and
one or several blower plate mounting screw(s).
Remove the blower plate from cabinet. See
Figure 20.
2. Carefully lift the blower unit out of the microwave
oven.
3. Rotate blower unit 90° so the exhaust ports face
the front of the cabinet. See Figure 21.
4. Place blower unit back into microwave oven.
5. Reattach blower plate to microwave oven.
Attach with the one blower unit mounting screw
and then the one or several blower plate
mounting screw(s). See Figure 22.
Figure 20
Blower Plate
Mounting Screw
Blower Plate
Back Plate
Parts B
Blower Unit
Figure 22
Blower Plate
Mounting Screw
Blower Plate
Back Plate
Parts B
Blower Unit
Figure 21
Blower Unit
Blower Plate
Mounting Screw
Blower Plate
Mounting Screw
– 13 –
STEP 4: Prepare The Wall & Upper Cabinet
To avoid personal injury or property damage, do not attempt to install this microwave
oven if you cannot find a wall stud. Consult a carpenter or contractor.
WARNING
Measure And Track/Tape Up The Templates
1. Using a plumb line and (metal) measuring tape, find and
mark the vertical center line on the back wall, as in
Figure 23.
2. Find and mark one or two points where the studs are on
the wall. (Studs are normally 16 inches apart). Then
measure and mark the stud locations. If you cannot find
any wall stud, consult a local building contractor.
3. Line up the plumb line on the wall with the center line
on the mounting plate.
NOTE: Be sure the minimum width is 30 inches and the
distance from the top of the wall template to the
range or counter top is at least 30 inches. See
Figure 23.
4. Center mounting plate in operating by lining up the
plumb line on wall with centerline on mounting plate.
Make sure the minimum width is 30 inches and that the
top of the mounting plate is located a minimum of 30
inches above the cooking surface. See Figure 24.
NOTE: If the cabinets are not plumb, adjust the mounting
plate to the cabinets. If the front edge of the
cabinet is lower than the back edge, adjust the
mounting plate to be level with the cabinet front.
5. Measure the bottom of the upper cabinet frame. Trim
the edges A, B, and C on the upper cabinet template
so that the template will fit on the bottom of the upper
cabinet. If upper cabinet has a recessed frame, trim the
template so it fits inside the recessed area. Align the
centerline of the upper cabinet template with the
centerline of the mounting plate, then securely tape or
tack the upper cabinet template in place. See Figure
24.
DO NOT ATTEMPT TO INSTALL THE MICROWAVE OVEN IF YOU CANNOT FIND A WALL
STUD.
CAUTION
Figure 23
Figure 24
Upper Cabinet Template
Mounting Plate
(1-piece Mounting Plate)
Upper Cabinet Template
Mounting Plate
(3-piece Mounting Plate)
– 14 –
STEP 4: Prepare The Wall & Upper Cabinet
Drill The Holes In The Wall And Upper Cabinet.
1. Drill holes on the circles. If there is a stud, drill a 3/16
"
hole
for lag screws. If there is no stud, drill a 3/4
"
hole for toggle
bolts. Make sure to use at least 2 lag screws in a stud, and
4 toggle screws in the drywall or the plaster.
2. Drill a 3/8” hole at points J and K on the upper cabinet
template.
NOTE: If the bottom of the upper cabinet is recessed 3/4
"
or more, you will need 2"x 2"filler blocks (not
included) to provide additional support for the bolts.
See Figure 25.
Mark the center of each filler block and drill a 3/8”
diameter hole at the marks.
Align filler blocks over the two openings in the top
of the microwave oven cabinet and attach to
cabinet with masking tape. See Figure 26.
3. Cut or drill a 2
"
diameter hole at the area marked M. Power
supply cord hole on the upper cabinet template. If the upper
cabinet is metal, you will need to cover the edge of the hole
with the power supply cord bushing (supplied) to prevent
damage to the cord from the rough metal edge.
4. Cut out the venting areas (with the saber saw):
Roof-Vented: cut out the shaded area marked L on the
upper cabinet template.
Wall-Vented: Tape the rear wall template to the rear wall,
lining up with the holes previously drilled for holes A and
B in the plate. Cut out the shaded area marked F on the
REAR WALL TEMPLATE.
Room-Vented: go to STEP 5, INSTALL THE MOUNTING
PLATE, located on page 15.
5. Complete whichever venting system you have chosen. Use
caulking compound to seal the exterior wall or roof opening
around the wall cap or roof cap.
Figure 25
Figure 26
Cabinet Front
Cabinet
Bottom Shelf
Filler Block
Filler
Block
To avoid risk of personal injury, electrical shock or death:
Note where electrical outlets and electrical wires are before you drill into the wall.
Locate and disconnect power to any electrical circuits that could be affected by
installing this oven.
WARNING
To avoid risk of personal injury, electrical shock or death, cover the edge of the power
supply cord hole with the power supply cord bushing.
WARNING
– 15 –
STEP 5: Install The Mounting Plate
Center Line
A
C
B
Draw
Center Line
Draw Lines
on Studs
For Wall-
Vented Only
Minimum 66
"
From the Floor
Support Tab Support Tab
E
Mounting
Plate
D
3/16 Hole on Studs
5/8 Hole on Drywall Only
3/16 Hole on Studs
5/8 Hole on Drywall Only
Center Line
Draw
Center Line
Draw Lines
on Studs
For Wall-
Vented Only
Minimum 66
"
From the Floor
Support Tab Support Tab
E
Mounting
Plate
C
D
A
B
(1-piece Mounting Plate)
(3-piece Mounting Plate)
The Oven Must Be Connected To At Least One
Wall Stud.
1. Draw a vertical line on the wall at the center of the 30" wide
space. Use the mounting plate as the template for the rear
wall. Place the mounting plate on the wall, making sure that
the tabs are against the bottom of the cabinet. Line up the
notch and center line on the mounting plate to the center line
on the wall.
2. While holding the mounting plate with one hand, draw circles
on the wall at holes A, B, C, and D. Four holes must be used
for mounting. If the holes are not used, the installation will not
be secure. Installer must use these holes for proper
installation. Use toggle bolts through these holes unless one
of them lines up with a stud. Use a wood screw for studs.
NOTE: Draw a fifth circle inside area E, through one of the
bottom holes to match the location of a stud. For wallvented: The oven requires a rear wall cutout opening for
the rear wall duct and the exhaust adaptor must be
attached to the mounting plate. See the next page on
how to prepare the rear wall cutout opening and the
exhaust adaptor/mounting plate for wall-vented.
3. Drill holes on the circles. If there is a stud, drill a 3/16 hole for
lag screws. If there is no stud, drill a 5/8 hole for toggle bolts.
Make sure to use at least 1 lag screw in a stud, and 4 toggle
bolts in the drywall or the plaster.
4. Attach the plate to the wall. To use spring toggle head bolts:
Remove the toggle wings from the bolts. Insert the bolts into
the mounting plate and replace the spring toggle head to 3/4
past the bolt ends. Insert the spring toggle head into the
holes in the wall to mount the plate. You may pull forward on
the plate to help in tightening the toggle bolts. Tighten all
bolts.
Figure 28
Figure 27
Wall
Mounting
Plate
Space More Than Wall Thickness
Bolt
End
Toggle Bolt
Toggle Wings
– 16 –
STEP 5: Install The Mounting Plate
Slide exhaust
adaptor into
guides on
rear panel.
Exhaust Adaptor
Damper
(hinge side up)
Locking
Tabs
Guides
Mounting Plate
Back Plate
(1-piece
Mounting Plate)
(3-piece
Mounting Plate)
For Wall-Vented
Make the box cutout for the rear wall duct.
– 1-piece mounting plate:
Using a pencil, put dots through slots F and G, and
through holes H and I. Remove the mounting plate and
draw lines extending through the points. This will give
the location and size of the box cutout for the rear wall
duct. (Figure 29)
– 3-piece mounting plate:
Use the wall template to determine the location and size
of the box cutout for the rear wall duct.
Attach the exhaust adaptor to the rear mounting plate
(back plate) wall side. Push in securely until it is past the
top locking tabs and in the lower locking tabs. Take care to
assure the damper hinge is installed so that it is at the top
and that the damper swings freely.
Carefully guide the exhaust adaptor, now attached to the
mounting plate, into the house duct. Before using the
screws to attach the plate to the wall. This will assure
proper alignment for installation.
Return to step 5, item 3 to continue. After completing the
installation of the mounting plate, again check the rear
damper for free movement to assure it will operate
properly.
Figure 29
Figure 30
– 17 –
STEP 6: Attach The Oven To The Wall
1. Carefully lift microwave oven and hang it on support tabs
(See Figure 27) at the bottom of the mounting
plate.Reaching through upper cabinet, thread
power supply cord through the power supply cord
hole in the bottom of the upper cabinet.
See Figure 31.
2. Rotate the microwave oven upward so the top of
oven is against the bottom of the upper cabinet or cabinet
frame.
3. Then insert a bolt down through each hole in the
upper cabinet bottom.See Figure 32.
Tighten the bolts until the gap between the upper cabinet
and microwave oven is closed.
4. If wall-vented or room-vented installation is used,go to No.
7 on the next page.
Figure 31
Figure 32
Power Cord
Power Cord
Hole
To avoid risk of personal injury or property damage, you will need two people to
install this microwave oven.
WARNING
– 18 –
STEP 6: Attach The Oven To The Wall
Damper
Power
supply
Cord
Clamp
5. Roof venting installation: See Figure 33.
Install ductwork through the vent opening in the
upper cabinet. Complete the venting system through the
roof according to the method needed. See
Prepare The
Venting System
STEP 2.
Use caulking gun to seal the exterior roof opening around
the exhaust cap. See Figure 7 on page 8.
6. Use the power supply cord clamp to bundle the power
supply cord. Install the power supply cord clamp, using a
screw as shown in Figure 34, to inside of the cabinet.
7. Grasp filter screen with one hand holding the ring and the
other hand holding the opposite end. Insert the end of the
filter screen without ring into the opening and slide
towards the side of the microwave oven. Insert ring end of
filter screen into the opening and slide entire screen
towards the center of the microwave until screen is
securely in position. Repeat for other filter screen. See
Figure 35.
8. Plug in the power supply cord.
9. Read your Owner’s Manual, then check the operation of
your microwave oven.
Figure 33
Figure 34
Figure 35
Printed in China
Loading...