GME TX3520W User Manual
INSTRUCTION MANUAL
Compact fully featured 5 watt UHF CB radio
Compact fully featured remote mount 5 watt UHF CB radio
Compact fully featured remote mic 5 watt UHF CB radio
ScanSuite
™
faster, smarter scanning
CONTENTS
SUPPLIED WITH .................................................................3
INTRODUCTION ................................................................3
IMPORTANT INFORMATION CONCERNING UHF
CB RADIO .........................................................................3
Possible Issues ...........................................................4
Emergency Channels..................................................4
Telemetry Channels ...................................................4
FEATURES .........................................................................4
GENERAL OPERATIONS .....................................................6
TX3510S/TX3520S Front Panel Controls .....................6
LCD Panel .................................................................6
Rear Panel .................................................................6
TX3540S Controller Microphone ................................7
TX3510S/TX3520S Microphone .................................7
TX3540S Controller LCD Panel ...................................7
GENERAL OPERATION ACROSS ALL MODELS ...................8
Keypad Functions ......................................................8
Volume .....................................................................9
Selecting Channels ....................................................9
Squelch .....................................................................9
Signal Meter ..............................................................9
Transmitting .............................................................. 9
Time-Out Timer ........................................................10
Backlighting ............................................................10
Bandwidth Filter Settings .........................................11
Dynamic Volume Control ..........................................11
Voice Scrambler .......................................................11
Beep Tone Volume ...................................................12
Silent Squelch Tail ....................................................12
Repeaters and Duplex Mode ....................................12
Priority Channel .......................................................13
Scanning .................................................................13
Open Scan ...............................................................14
Group Scan .............................................................15
Network Scan ..........................................................16
CTCSS and DCS .......................................................18
Selective Calling ......................................................20
Using SelCall ...........................................................20
Responding to SelCall Alert ......................................22
Quiet Mode .............................................................22
Group Calling ..........................................................24
Receive-only Channels .............................................25
Configuration Menu ................................................29
INSTALLATION ................................................................30
General ...................................................................30
TX3510S and TX3540S Installation ..........................30
TX3520S Installation ...............................................31
Microphone .............................................................31
DC Power Connection ..............................................32
ANTENNA CONNECTION ................................................33
NOISE SUPPRESSION .......................................................33
Wiring .....................................................................34
CTCSS TONE FREQUENCY CHART ....................................35
DCS TONE CHART............................................................36
UHF CB OPERATING FREQUENCIES .................................37
SPECIFICATIONS .............................................................38
SC CONTRACT WARRANTY AGAINST DEFECTS ................39
PAGE 2 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 3
SUPPLIED WITH
TX3510S TX3520S TX3540S
TX3510S Radio TX3520S Radio TX3540S Radio
Mounting Cradle
Microphone
TX3520S Remote Head
Mounting Cradle
Mounting Cradle
Controller Microphone
Microphone Clip Microphone Microphone Extension Lead
DC Lead Microphone Clip 8 Pin to 8 Pin Adapter
Screw Pack DC Lead Microphone Clip
Instruction Manual Connecting Cable DC Lead
Screw Pack Screw Pack
Instruction Manual Instruction Manual
INTRODUCTION
Your GME TX3510S/TX3520S/TX3540S 80 channel radio
is Australian designed and built and is the most advanced
UHF Citizen Band radio available. It combines the very latest
in electronic hardware with the most up-to-date computer
aided design and manufacturing techniques to produce
an extremely compact mobile radio with outstanding
specifications and performance.
Your radio is designed for unobtrusive mounting in modern
vehicles. With its built-in loud speaker and extremely small
size, it can be mounted in almost any convenient location.
IMPORTANT INFORMATION
CONCERNING UHF CB RADIO
The use of the Citizen Band radio service is licensed in
Australia by the ACMA Radio communications (Citizens
Band Radio Stations) Class Licence and in New Zealand by
the Ministry of Economic Development New Zealand (MED).
A General User Radio Licence for Citizens Band radio
and operation is subject to conditions contained in those
licences.
The class licence for users and equipment operating in the
CB/PRS 477 MHz band has been amended. This radio meets
the new 80 channel standard.
In simple terms the same amount of spectrum is available;
however,
radio transceivers can now operate in a narrower
bandwidth and hence use less spectrum. These radios are
generally referred to as narrowband or 12.5 kHz radios. By
using 12.5 kHz channel spacing instead of 25 kHz, the 40
channels originally allocated can now be expanded to 80
channels thereby doubling the channel capacity and relieving
congestion in the UHF CB/PRS band.
Original 40 channel wideband Radios will continue to operate
on the original 40 channels, however they will not be able
to converse on the newer channels 41 – 80. The newer
narrowband radios will be able to converse with all older 40
channel wideband radios on all channels 1 to 40 as well as the
newer channels allocated from 41 to 80.
The mixing of narrowband and wideband radios in the same
spectrum can cause some possible operating issues
of interference and varying levels of received volume.
POSSIBLE ISSUES
When a new narrowband radio receives a transmission
from an older wideband radio the speech may sound loud
and distorted – simply adjust your radio volume for best
performance.
When an older wideband radio receives a signal from a new
narrowband radio, the speech may sound quiet – simply
adjust your radio volume for best performance.
EMERGENCY CHANNELS
The ACMA has allocated channels 5/35 for emergency use
only. Channel 5 is the primary Simplex Emergency Channel.
Where a Channel 5 repeater is available, you should select
Duplex on CH 5.
NOTE: Channel 35 is the input channel for the Channel 5
repeater therefore Channel 35 should also not be used for
anything other than emergency transmissions.
Depending on how close your receiving radio is to another
transmitting radio, there can be interference from the
transmitting radio if it is using a channel adjacent to the
channel you are listening to. Simply try going up or down a
few channels from the currently selected channel.
The above situations are not a fault of the radio but a symptom
of operating wideband and narrowband radios in the same
bandwidth. This possible interference will decrease over time
as the population of wideband radios ages and decreases.
Further information and updates are available from the
Australian Communications and Media Authority (ACMA)
at www.acma.gov.au and the Ministry of Economic
TELEMETRY CHANNELS
ACMA regulations have allocated channels 22 and 23
for telemetry only applications and have prohibited the
transmission of speech on these channels. Consequently your
radio has a transmit inhibit applied to channels 22 and 23.
In the event additional telemetry/telecommand channels are
approved by the ACMA, these channels shall be added to
those currently listed where voice transmission is inhibited.
Currently transmissions on channels 61, 62 and 63 are also
inhibited and these channels are reserved for future allocation
Development (MED), Radio Spectrum Management at:
www.rsm.govt.nz
FEATURES
TRANSMIT (TX)
Individually Programmable DUPLEX Function: User selectable for only those individual channels in your area that have
repeaters, leaving the others free for use as extra simplex channels.
RECEIVE (RX)
Silent Squelch Tail: Eliminates the Squelch noise burst normally audible when the Squelch closes
User Programmable Receive Channels: 95
Signal Receive Indicator: Confirms that an incoming signal is being received
SCANNING AND MEMORY FUNCTIONS
Microprocessor Controlled Frequency Synthesiser: Allows user programmable control of scanning, channel memories
and selected feature options.
Programmable Scan Function
functions available.
PAGE 4 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 5
: Scans the selected UHF CB channels with Group, Open and Network scan
Priority Channel: A user programmable Priority channel feature allows your working channel to be instantly recalled at the
press of a key.
SIGNAL PROCESSING
Digital Signal Processing:
digital format. Allows advanced RF and audio processing techniques to be applied to maximise the radio’s performance.
Advanced Signal Management: Identifies interference caused by strong local signals on adjacent channels and prevents
these from opening your Squelch. ASM also minimises distortion on reception by fine tuning the receiver frequency to match
that of the incoming signal.
Dynamic Volume Control: Automatically compensates for variations in received audio level to provide a constant audio
output level to the speaker.
User Selectable Wide/Narrow Band Filter: To accommodate the blending of 80 channel narrow band radios with older
40 channel wideband radios.
PRIVACY FUNCTIONS
Voice Inversion Scrambler: When activated, scrambles your voice so that communications are only intelligible to others
using the same scrambler technology.
Inbuilt CTCSS & DCS: User selectable Continuous Tone Coded Squelch System and Digital Coded Squelch system provides
silent operation on individual channels.
In-Built SelCall with Quiet Mode: Provides selective calling of individuals or groups with fully user-adjustable 5-tone
transmitted SelCall Ident. Also allows alphanumeric naming of up to 10 Idents for easier caller identification.
PHYSICAL PROPERTIES
Over Voltage Protection: Special overvoltage detection circuitry protects the radio and warns of excessive voltage
conditions by flashing the display.
Rugged Construction: With Die-cast Chassis
USER CONTROLS AND INTERFACE
Full Spectrum Backlighting: User adjustable, totally customisable backlight settings to match the vehicles dashboard
lighting or drivers preference.
High Contrast Liquid Crystal Display: Fully detailed LCD provides a visual indication of the selected channel and all
selected functions at a glance.
Front and Rear Microphone Inputs: Convenient front and rear microphone inputs to facilitate ease of installation and
operation across a range of vehicles.
Digital Signal Strength Meter: Provides a numeric signal strength indication in numbers from 0 to 9+
Measures, filters and compresses standard analogue audio signals and converts them into
GENERAL OPERATIONS
TX3510S/TX3520S FRONT PANEL CONTROLS
Front Mic Input
Channel Control
Liquid Crystal Display
Volume Control
PUSH
SQL LVL
Push for Squelch Level/
Priority Channel
PUSH
PRIORITY
MENU
F
Menu/
Function
SCAN
OS/GS
OS-GS
Scan/
QUIET
DUP
Duplex
Quiet/
SQL
ALPHA
Squelch/
Alpha
LCD PANEL
SelCall TX
SelCall RX
SelCall/Alpha Display/
Signal Meter/Battery
Quiet Tag
Scan
Channel Display
Busy
Repeater
(Duplex)
Quiet
Transmit
CTCSS/DCS
REAR PANEL
DC Power Socket
PAGE 6 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 7
Speaker Socket
Antenna Socket Rear Microphone Socket
TX3540S CONTROLLER MICROPHONE TX3510S/TX3520S MICROPHONE
Push-To-Talk (PTT)
Menu/
F Key
Power Key/
Monitor
Microphone
Channel Up
Channel Down
TX3540S CONTROLLER LCD PANEL
Scan
Quiet Tag
SelCall RX
SelCall TX
Skip/Call
LCD Display
SCAN/
OS/GS
Quiet/
Duplex
Squelch/
ALPHA
Squelch level/
Priority channel
Volume Up
Volume Down
Channel Display
Channel
Down
Push To
Talk
Squelch Set /
Skip/Call
Channel
Up
Priority
Transmit
Busy
Repeater (Duplex)
SelCall/Alpha Display/Signal Meter/Battery Quiet CTCSS/DCS
GENERAL OPERATION ACROSS ALL MODELS
KEYPAD FUNCTIONS
The controls on the TX3510S and TX3520S front panel and
TX3540S controller microphone all have multiple functions.
The primary functions are labelled in BLACK, while the
secondary functions are labelled in RED. To access a primary
function simply press the required key.
To access a secondary function, briefly press the F key
followed immediately by the required key.
The table below shows the control functions for all models.
TX3510S/
TX3520S
CHANNEL
PUSH PUSH
PRIORITYSQL LVL
VOLUME
TX3540S FUNCTION
MENU
F
Press and hold MENU to access the configuration menu. Press F
followed by the required key to access the secondary key-functions
labelled in
SCAN
OS/GS
QUIET
DUP
Press SCAN to toggle scanning on or off. Press F followed by
select Open Scan, Group Scan or Network Scan.
Press and hold QUIET to tag the selected channel for use with SelCall.
Press QUIET briefly to toggle the quiet mode on all channels that have
been tagged. Press F followed by
on the selected channel.
SQL
ALPHA
Press SQL briefly to toggle the Squelch on or off. Press and hold SQL to
toggle CTCSS/DCS silent mode on or off on the selected channel. Press
F
followed by
Rotate the Channel control (or press
LV L
PRI
Press the Channel control (or the LVL key) briefly to adjust the preset
Squelch level. Press
to recall the Priority channel.
F
then press and hold the Channel control (or the
Press
store the current channel as the Priority channel.
+
–
PWR
Rotate the Volume control past the click (or press the PWR key) to
switch the radio on or off.
Rotate the Volume control (or press the + or - keys) to adjust
the volume.
red
.
DUP
to toggle duplex mode on or off
ALPHA
to toggle Alpha or Numeric display modes.
or )
F
followed by the Channel control (or the
OS/GS
to change channels.
PRI
PRI
key) to
to
key)
PAGE 8 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 9
NOTE: When using the F key to access other functions, F is
displayed to indicate that ‘Function’ mode is activated. If the
required function is not selected within 6 seconds the F key
selection will time out with a low beep and F will disappear
from the display.
A more detailed description of these key functions is included
below. These instructions describe the radio functions using the
TX3510S/TX3520S controls (with the TX3540S controls shown
in brackets).
VOLUME
Rotate the Volume control clockwise past the click (or press
the PWR key) to turn the radio on. Rotate the Volume
control left or right (or press the + or – keys) to adjust the
volume.
If no sound is heard, briefly press the SQL key to temporarily
un-mute the radio then adjust the Volume control while
listening to the background noise. When finished, briefly
press the SQL key again to re-mute the radio.
NOTE: At the minimum volume setting there is still sufficient
volume to be heard in a quiet cabin environment.
SELECTING CHANNELS
To select the required channel, rotate the Channel control
(or press the
clockwise (or press
clockwise (or press
channel is displayed on the LCD.
SQUELCH
The Squelch is used to eliminate any annoying background
noise when there are no signals present. The Squelch can
be opened or closed using the SQL key. When the Squelch
is open the receiver’s background noise can be heard and
the
receiver remains quiet while there are no signals present but
any incoming signals will override the Squelch and be heard
in the speaker.
or keys). Rotate the Channel control
) to select a higher channel or counter
) to select lower channels. The selected
symbol is displayed. When the Squelch is closed the
Adjusting the Squelch level
The Squelch sensitivity level has been factory set to provide
optimum performance under most operating conditions. If
required, the sensitivity level can be adjusted to suit
changing conditions.
To adjust the Squelch sensitivity, briefly press the Channel
control (or LVL key). The channel display will show the
current Squelch level setting in values from SQL-1 to SQL-9.
Rotate the Channel control (or press the
the controller microphone) to change the Squelch setting.
A Squelch setting of SQL-1 allows the Squelch to open on
very weak signals whereas a setting of SQL-9 requires much
stronger signals to overcome the Squelch. After adjusting the
Squelch sensitivity, briefly press the Channel control (or LVL
key) to return to normal operation.
NOTE: The Squelch level can be actively adjusted while the
radio is scanning. This allows you to tighten the Squelch in
cases where an undesired weak or noisy signal is interrupting
the scan.
SIGNAL METER
The signal meter indicates the relative strength of the
incoming signal in numerical format. Signal strengths are
displayed on the lower left of the Channel Display in values
from 0 to 9. Signals above strength 9 are displayed as 9+.
NOTE: Refer to the Configuration Menu for other options
that can be displayed in this location.
TRANSMITTING
Prior to transmitting, always check the channel is not being
used. This can be done by listening to the channel or by
visually checking that the
meter is not indicating a signal.
To transmit, press the PTT on the microphone. The
will appear. Hold the microphone about 5-8 cm from your
icon is not visible or the signal
or keys on
icon
face and speak at a normal voice level. The microphone is
quite sensitive so it is not necessary to raise your voice or
shout. Release the PTT when you have finished talking. The
icon will disappear.
IMPORTANT: Always listen to ensure the channel is free
before transmitting.
TIME-OUT TIMER
The radio has a built-in time-out timer that automatically
limits transmissions to a maximum of 3 minutes of
continuous operation. This feature is required by the ACMA to
prevent accidental blocking of the frequency should your PTT
become jammed or be otherwise pressed accidentally. The
time-out period can be changed by your dealer.
When the time-out timer activates, the radio will beep for 5
seconds then the
symbol will flash continuously. Normal
operation will be restored once the PTT is released.
BACKLIGHTING
The Liquid Crystal Display and keys are backlit for easier
viewing at night. The backlight remains on whenever the
radio is switched on.
Adjusting the Backlighting
The backlight brightness and colour can be adjusted for
personal preference. There are three backlight settings
available.
BKLGT (Brightness setting): Provides a continuously
variable brightness adjustment from very dim to full
brightness.
COLOR (Colour set ting): Provides a continuously variable
adjustment through the full colour spectrum.
White (Whiteness setting): Controls the colour
saturation of the selected colour from deep colour to white
(no colour).
To adjust the backlighting;
1. Hold the Channel control (or LVL key) to select the
Backlight mode. ‘BKLGT’ is displayed.
2. Rotate the channel control left or right (or press or
keys) to adjust the brightness.
3. Briefly press the Channel control (or LVL key) to select
the Colour setting mode. ‘COLOR’ is displayed.
4. Rotate the Channel control left or right (or press
or
keys) to adjust the colour.
5. Briefly press the Channel control (or LVL key) to select
the Whiteness setting mode. ‘WHITE’ is displayed.
6. Rotate the Channel control left or right (or press
or
keys) to adjust the colour saturation. For the deepest
colour range, reduce the WHITE setting.
To exit, press and hold the Channel control (or LVL key).
Auto-colour Mode
The radio has an automatic colour-change option that, when
activated, will cause the display colour to automatically cycle
through the available colour spectrum. The colour-change
option can be enabled temporarily as an aid to choosing
a display colour or can be set to cycle continuously as the
preferred display colour setting.
To enable the auto-colour option,
7. Hold the Channel control (or LVL key) to select the
Backlight mode. ‘BKLGT’ is displayed.
8. Briefly press the Channel control (or LVL key) to select
the Colour setting mode. ‘COLOR’ is displayed.
9. While in the colour setting mode, briefly press the MENU
key to enable or disable the auto-colour option. When
enabled, the display lighting will continuously cycle
through the available colour spectrum. When disabled the
display will hold the last selected colour.
To exit, press and hold the Channel control (or LVL key). If
auto-colour is still enabled, the display lighting will continue
to cycle through the colour spectrum until disabled using the
steps above.
NOTE: The back-light setting function will automatically
time out after 6 seconds if no further adjustments have
been made.
PAGE 10 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 11
BANDWIDTH FILTER SETTINGS
To accommodate the blending of newer 80 channel
narrowband UHF radios with the original 40 channel
wideband radios, your radio has been fitted with two user
selectable receiver bandwidth filters. While the use of
either filter will provide superb receive audio, selecting the
wideband filter while on channels 1-40 will further increase
your receiver’s tolerance to older 40 channel wideband
radios that might otherwise sound over-modulated or
mildly distorted. Select the narrowband filter to improve
the selectivity of the receiver to provide greater resistance
to interference from older 40 channel wideband radios
operating on adjacent channels.
To select the desired filter
1. Press and hold MENU to enter the menu.
2. Press MENU repeatedly until ‘NBFLT’ (Narrowband Filter)
or ‘WBFLT’ (Wideband Filter) is displayed.
3. Rotate the Channel control (or press
make the desired selection.
When finished briefly press the PTT to exit the menu.
or keys) to
Narrowband filter selected
differences in received audio volume between stations.
Generally users have compensated for this by adjusting
the Volume control for each incoming signal. With the
introduction of 80 channel narrowband transmissions that
use lower levels of modulation, the diversity in received audio
volume is likely to increase further.
Your radio is able to automatically compensate for these
variations in received audio level by utilising a Dynamic
Volume Control. When activated, this feature automatically
compensates for variations in received audio level resulting in
a constant audio output level to the speaker.
To activate the Dynamic Volume Control
1. Press and hold MENU to enter the menu.
2. Press MENU repeatedly until ‘DVCOF’ (Dynamic Volume
Control Off) or ‘DVCON’ (Dynamic Volume Control On) is
displayed.
3. Rotate the Channel control (or press
make the desired selection.
When finished briefly press the PTT to exit the menu.
or keys) to
Dynamic Volume Control ON
Wideband filter selected
NOTE: The wideband receiver filter setting is only applied
to channels 1 – 40. Channels 41 – 80 always use the
narrowband filter.
DYNAMIC VOLUME CONTROL (DVC)
The modulation level of signals heard on the UHF CB band
has always varied considerably resulting in noticeable
Dynamic Volume Control OFF
VOICE SCRAMBLER
Your radio incorporates a simple voice scrambler using band
inversion. The scrambler is compatible with the majority
of scramblers used by other manufacturers, allowing you
to enjoy scrambled communications with owners of nonGME radios. Once the scrambler has been activated your
transmission and reception will only be intelligible to others
using the same scrambler technology.
To enable or disable the voice scrambler
1. Press and hold MENU to enter the menu.
2. Press MENU repeatedly until ‘ENCOF’ (Encoder Off) or
‘ENCON’ (Encoder On) is displayed.
3. Rotate the Channel control (or press
or keys) to
make the desired selection. Select ‘ENCON’ to activate
the scrambler or ‘ENCOF’ to disable it.
When finished briefly press the PTT to exit the menu.
2. Press MENU repeatedly until ‘SSTxx’ is displayed where xx
=ONorOF.
3. Rotate the Channel control to the right (or press the
key) to enable the Silent Squelch Tail. ‘SSTON’ will be
displayed and the Squelch Tail will become silent.
4. Rotate the Channel control to the left (or press the
key) to disable the Silent Squelch Tail. ‘SSTOF’ will be
displayed and the Squelch Tail will be restored.
When finished, briefly press the PTT to exit.
REPEATERS AND DUPLEX MODE
Scrambler Encoder OFF
Scrambler Encoder ON
BEEP TONE VOLUME
The Key Beeps provide audible feedback whenever the keys
are pressed. You can adjust the volume of the key beeps
as follows.
1. Press and hold MENU to enter the menu.
2. Press MENU repeatedly until ‘BEEPx’ is displayed (where
x is a value from 0 – 9).
3. Rotate the Channel control (or press the
or keys)
to adjust the Beep volume from 0 – 9.
• BEEP1=minimum
• BEEP9=maximum
• BEEP0=Off
When finished, briefly press the PTT to exit.
SILENT SQUELCH TAIL
The Squelch Tail is the short burst of noise that is heard in
the speaker at the end of a transmission just before the
Squelch closes.
To some it is a reassuring confirmation that it is their turn to
transmit but in some applications it may be an annoyance
especially when listening through an earpiece or headphones.
The Silent Squelch Tail function removes this Squelch Tail,
reducing it to a faint click as the Squelch closes.
To enable or disable the Silent Squelch Tail
1. Press and hold MENU to enter the menu.
PAGE 12 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 13
Duplex operation allows the radio to transmit on a different
frequency to that which it receives. This allows operation
through repeater stations.
A repeater station consists of a linked transmitter/receiver
combination installed in a prominent location. The repeater
is designed to receive signals on a designated channel and
retransmit them on another channel. Repeaters are usually
mounted on hills or tall buildings. The increase elevation
greatly improves both the receiving and transmitting range of
the repeater allowing it to receive and retransmit signals to
radios that would otherwise be out of range of each other.
Normally, UHF radios transmit and receive on the same
frequency – known as Simplex operation. However to
communicate through repeaters, your radio must be able to
transmit and receive on different channels – otherwise known
as Duplex operation. Your radio is fitted with a Duplex key to
allow you to operate through repeaters.
The Duplex function can only be selected on channels 1 – 8
and 41 – 48 as these are the channels that have been
allocated for repeater use. When Duplex is selected, your
radio receives on the selected channel (e.g. CH 1) but
transmits 30 channels higher (CH 31). The repeater hears your
signal on CH 31 and retransmits it on CH 1 for others to hear.
SIMPLEX
REPEATER
OPERATION
CHANNEL 1
CHANNEL 31
VEHICLE
VEHICLE
CHANNEL 31
CHANNEL 1
REPEATER
STATION
Your radio allows you to enable or disable Duplex mode
on individual repeater channels. In this way any repeater
channels that are not being used with repeaters in your area
can be used in Simplex mode for normal direct radio-to-radio
communications.
Channel Selected Receive Channel Transmit Channel
1 1 31
2 2 32
3 3 33
4 4 34
5* 5* 35*
6 6 36
7 7 37
8 8 38
41 41 71
42 42 72
43 43 73
44 44 74
45 45 75
46 46 76
47 47 77
48 48 78
*Emergency channel only
To Enable Duplex on a Repeater Channel
1. Select the required repeater channel (1 – 8, 41 – 48).
2. Press F followed by the DUP key. The duplex symbol
will appear on the display accompanied by a high beep.
To Remove Duplex from a Repeater Channel
1. Select the required repeater channel (1 – 8, 41 – 48). If
duplex is currently selected, the
displayed.
duplex symbol will be
2. Press F followed by the DUP key. The duplex symbol
will disappear from the display accompanied by a low beep.
IMPORTANT: Channels 1 – 8, 31 – 38, 41 – 48 and
71 – 78 should only be used in Simplex mode if there are
no repeaters in or near your location that operate on the
selected channel. In particular, avoid operating in Simplex
mode on any of the repeater input channels 31 – 38 and
71 – 78 unless you are absolutely sure that there are
no repeaters in range using that channel. Inadvertently
transmitting on an active repeater input frequency in simplex
mode could cause interference to other users on that repeater
that would not be audible to your radio.
PRIORITY CHANNEL
The Priority channel feature allows you to instantly recall any
one of the 80 channels in your radio. This feature can be
used to provide instant access to your working channel or
your local repeater channel at the press of key. It is also used
in conjunction with the Group Scan mode.
To Store a Priority Channel
1. Select the required channel.
2. Press F then press and hold the Channel control (or LVL
key). The channel number will flash then a high beep will
be heard as the channel is stored.
To Recall a Priority Channel
1. Press F then briefly press the Channel control (or LVL
key). The radio will immediately switch to the Priority
channel and ‘PRI’ will be displayed for a few seconds.
NOTE: If the radio was scanning when the Priority channel
was recalled, the scan will be cancelled.
SCANNING
Your radio incorporates a scan function allowing selected
groups of channels to be scanned for signals. Channels
can be scanned at a rate of 40 channels per second.
When a signal is found, scanning will pause to allow
the signal to be heard then resume scanning when the
channel is clear again.
Scan Groups
Your radio supports three scan groups - Open Scan, Group
Scan and Network Scan. Each scan group has a separate
channel memory allowing you to program your choice of
channels into each group for scanning.
To select Open Scan, Group Scan or Network Scan, press F
then OS/GS. ‘OPEN’, ‘GROUP’ or NETWK’ will be displayed
at each press.
NOTE: Network scan is disabled by default and will not
appear in the scan group list unless it has been enabled. See
Network Scan further below for details on how to enable
and use Network Scan.
Auto Skip
While scanning, if an active channel in your scan group
becomes a nuisance by constantly interrupting the scan,
briefly rotate the Channel control (or press
while the radio is paused on that channel. The busy channel
will be temporarily removed from the scan group to allow
time for the channel to become clear again and scanning will
continue from the next channel in the sequence. After 30
seconds the skipped channel will be reinstated in the scan
sequence.
If the unwanted active channel continues to interrupt the
scan even after the 30 second skip period has elapsed,
hold SCAN while the radio is paused on that channel. The
‘nuisance’ channel will be completely removed from the scan
group for the duration of that scan session. To restore the
channel, simply stop and restart the scan session using the
SCAN key (or switch the radio Off then On again).
NOTE: You can skip as many busy channels from the scan
group as you wish, however if you attempt to skip the last
remaining channel, all the previously skipped channels will be
restored to the scan group.
PAGE 14 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 15
or keys)
OPEN SCAN
Open Scan allows a group of channels to be scanned in an
ascending sequence. If a signal is found, the scan will pause
on that channel. During this time you can press the PTT on
the microphone and talk on the channel. Once the channel
has been clear for 5 seconds the scan will resume.
1 - 2 - 3 - 4 - 5 - 6 - 7 - 8
Example: Scanning channels 1 – 8 in Open Scan
Selecting Open Scan
To select Open Scan, repeatedly press F followed by OS/GS
until ‘OPEN’ is displayed.
Programming the Scan Memory
Your radio has all 80 channels factory-programmed into
the Open Scan memory. Any channels not required can be
removed.
To add or remove channels from the Open Scan memory:
1. Select the required channel using the Channel control (or
or keys)
the
2. Check to see if the scan symbol
channel.
is displayed, the selected channel is already in the
• If
scan memory. To remove it, press and hold SCAN.
will disappear.
is not displayed, the selected channel is not in the
• If
scan memory. To add it, press and hold SCAN. will
now be displayed on that channel.
Repeat to add or remove other channels in the scan memory.
Default Working Channel in Open Scan Mode
In the Open Scan mode, your default working channel is
the channel your radio switches to when you press the PTT
while scanning. To define your working channel simply select
the required channel before you press SCAN. e.g. to make
channel 24 your working channel, simply select channel 24
before pressing SCAN.
is displayed on that
To Begin Scanning
Briefly press SCAN. A high beep will be heard and the
symbol will animate. During this time the channel numbers
will scroll rapidly as the channels are scanned.
NOTE: If there are less than 2 channels programmed into the
scan memory when you press SCAN, a low beep will sound
and the command will be ignored.
Operating in the Open Scan Mode
If a busy channel is found, scanning will pause to allow the
signal to be heard and will remain there for as long as the
channel remains busy. Once the channel has been clear for 5
seconds, scanning will resume automatically.
If you don’t wish to listen to a busy channel, briefly rotate
the Channel control (or press the
radio is paused on that channel. The busy channel will be
temporarily removed from the scan group to allow time
for the channel to become clear again and scanning will
continue. The skipped channel will be reinstated in the scan
sequence after 30 seconds (see Auto Skip).
If you press the PTT while the radio is scanning, the scan will
pause and the radio will transmit on the working channel.
After the channel has remained been clear for 5 seconds
scanning will resume.
If your radio pauses on a busy channel and you wish
to talk on that channel, simply press the PTT during a
break in the conversation. If the busy channel was not
your working channel, it now becomes your new working
channel, replacing your previous working channel. Once your
communication has finished and the channel has been clear
for 5 seconds, scanning will resume.
If you need to use your Priority channel (for an urgent call),
briefly press PRI. The scan will be cancelled and the radio will
jump straight to the Priority channel.
GROUP SCAN
Group Scan allows you to scan a number of channels for
activity while also monitoring your Priority channel. The
receiver will scan the other channels ONLY WHILE THERE
or keys) while the
ARE NO SIGNALS ON THE PRIORITY CHANNEL. If a signal
appears on the Priority channel it will override any signals
being received on any of the other channels. In addition, if
you press the PTT at any time, the radio will transmit on the
Priority channel.
1 - 2 - 3 - 4 - 20 - 5 - 6 - 7 - 8 - 20
Example: Scanning channels 1 – 8 with priority
channel 20 in Group Scan
Selecting Group Scan
To select Group Scan, repeatedly press F followed by OS/GS
until ‘GROUP’ is displayed.
Programming the Scan Memory
1. Select the required channel using the Channel control (or
the
or keys).
2. Check to see if the scan symbol
channel.
is displayed, the selected channel is already in the
• If
scan memory. To remove it, press and hold SCAN.
will disappear.
is not displayed, the selected channel is not in the
• If
scan memory. To add it, press and hold SCAN. will
now be displayed on that channel.
Repeat to add or remove other channels in the scan memory.
Select your Priority Channel
Program your Priority channel as described earlier under
‘Priority Channel’
To Begin Scanning
Briefly press SCAN. A high beep will be heard and the
icon will animate. During this time the channel numbers will
change rapidly as the channels are scanned with the Priority
channel scanned every fourth channel.
If a signal appears on the Priority channel – at any time – the
radio will switch directly to the Priority channel and will stay
is displayed on that
there for as long as the channel remains busy. During this
time you can transmit and receive on the Priority channel.
Once the Priority channel has been clear for 5 seconds the
radio will resume scanning the other channels.
If a signal appears on any other channel, scanning will pause
on that channel and will remain there while the channel is
busy – as long as there are no signals on the Priority channel.
During this time, the receiver will continue to check the
Priority channel every 2 seconds resulting in a series of small
breaks in the reception of the busy channel. Once the signal
has gone and there has been no activity for 5 seconds, the
radio will resume scanning.
To transmit on the Priority channel at any time, simply press
the PTT. The radio will switch straight to the Priority channel.
When you have finished your conversation and there has
been no further activity for 5 seconds, the radio will resume
scanning the other channels.
If you don’t wish to listen to a busy channel, briefly rotate
the Channel control (or press the
or keys) while the
radio is paused on that channel. The busy channel will be
temporarily removed from the scan group to allow time
for the channel to become clear again and scanning will
continue. The skipped channel will be reinstated in the scan
sequence after 30 seconds (see Auto Skip).
If you need to use your Priority channel (for an urgent call),
briefly press the PRI key. The scan will be cancelled and the
radio will jump straight to the Priority channel.
If the radio is paused on a busy channel and you want to
remain there, briefly press SCAN. The radio will exit scan and
remain on the busy channel. At this point you will no longer
be monitoring the Priority channel.
To resume Group scanning press SCAN again.
NETWORK SCAN (NET-SCAN)
Net-Scan allows a group of radio users to maintain
communications even when the band is congested. To
achieve this all members of the Net-Scan group must share
a common CTCSS/DCS code and a common set of scan
channels.
Once activated, Net-Scan’s intelligent scanning software
keeps track of clear channels within your scan group. When
PAGE 16 INSTRUCTION MANUAL TX3510S/TX3520S/TX3540S TX3510S/TX3520S/TX3540S INSTRUCTION MANUAL PAGE 17
any member of the group transmits, their radio automatically
selects a clear channel to transmit on. Other radios scanning
in the same Net-scan group will lock onto that channel
allowing all members of the group to join the conversation.
If a signal from outside your Net-Scan group appears on the
chosen channel (either with no code or the wrong code), the
group will automatically switch to a new clear channel at
the next transmission. In this way the group can continue to
communicate with minimal interference to or from other users.
Enabling Net-Scan
Net-Scan is normally switched off by default but can be
enabled through your radio’s menu.
NOTE: When you enable Net-Scan you will also be prompted
to choose a suitable CTCSS or DCS tone to be used by your
Net-Scan group. All members of your Net-Scan group must
use this same code.
To Enable Net-Scan
1. Press and hold MENU to enter the menu.
2. Press MENU repeatedly until ‘NS xxx is displayed.
3. Rotate the Channel control (or press the
or keys)
to change the current Net-Scan setting.
• ToenableNet-ScanusingCTCSS,selectfromNS-01to
NS-50 (CTCSS tones 01 to 50).
• ToenableNet-ScanusingDCS,selectfromNS001to
NS104 (DCS codes 001 to 104).
• TodisableNet-Scan,select‘NS-OF’.
When finished briefly press the PTT to exit the menu.
Selecting Net-Scan
When Net-Scan is enabled, a Network scan option becomes
available in the scan group selection. To select Network
Scan, repeatedly press F followed by OS/GS until ‘NETWK’
is displayed.
Programming Channels into Net-Scan
All radios in your Net-Scan group must have the same
channels programmed into their Net-Scan memory.
Loading...