I N S T R U C T I O N M A N U A L
TELEPHONE
INTERCOM
TH10
DESCRIPTION
The GME TH10 is a telephone style intercom unit suitable
for both land based and marine installations where wired
communications is required between two or more locations.
Individually numbered buttons allow selective paging of up
to 10 stations.
INSTALLATION
WIRING
To prevent loss of performance, the wire used should have
a minimum diameter of 0.5 mm and should be no more
than 500 meters in length. To determine the number of
wires required, use the following formula:
No. of Stations + 3 = number of wires
(e.g. 5 stations + 3 = 8 wires)
1. Remove the screw in the mouthpiece recess of the case
and lift the case clear.
2. Feed the cables through the hole in the centre of the
case bottom and after removing the insulation from the
end of each wire, connect them to the terminal block
inside the intercom according to Figure 1.
3. To help eliminate wiring errors, connect each intercom in
sequence, then test each installation before proceeding
to the next. This allows you to identify and correct any
wiring errors as you go.
MOUNTING
The TH10 may be installed on any flat surface using
the mounting bracket supplied. Postion the bracket in
the desired location with the mounting lugs protruding
outwards and upwards, and secure with two 3 mm
diameter screws. Place the TH10 over the four protruding
lugs so that they locate in the slots in the case bottom,
and slide the Intercom downward until it locks. To remove,
use the reverse procedure.
POWER REQUIREMENTS
The TH10 requires a 12 Volt DC power supply. The supply
used will depend on your installation.
MARINE INSTALLATIONS
The TH10 can be connected directly to the 12 Volt battery
on board your boat using a FUSED power lead.
1. Connect the RED lead to the ‘+’ on the terminal block.
2. Connect the BLACK lead to the ‘-’ on the terminal block.
LAND BASED INSTALLATIONS
The TH10 should be connected directly to a 12 Volt DC
power supply capable of at least 100 mA such as the
GME Model BCE1445.
1. Cut the DC plug from the end of the BCE1445’s DC lead.
2. Connect the BLACK/WHITE STRIPE lead to the ‘+’ on the
terminal block.
3. Connect the BLACK lead without the stripe to the ‘-’
on the terminal block.
OPTIONAL EXTERNAL BUZZER
In high noise environments, it may be necessary to install
an external buzzer so that the station being called can
be alerted. Any low current 12 Volt buzzer can be used.
The buzzer should be connected to the terminal block
inside the intercom so that the POSITIVE wire of the
buzzer connects to ‘B’ and the NEGATIVE wire of the
buzzer connects to ‘-’ as shown in Figure 1.
I.D. LABEL
Write or type the station’s call number on the label
supplied, peel off the backing, and apply to the unit
in a visible location.
OPERATION
1. Pick up the handset and momentarily press the button
corresponding to the station you wish to call. The buzzer
will sound at the called station.
2. The person being called can then pick up the handset
and talk in the usual manner.
3. When you have finished, place the handset back onto
the base.
Note: The system has been designed so that during a
conversation, any handset in the system can be lifted from
its base and used to join in.
SPECIFICATIONS
Power Supply: 12 Volts DC @ 100 mA
Maximum Cable Length: 500 metres
No. of wires required: Min 5 (2 Stations)
Max 13 (10 Stations)
Operating Current: 10 mA per unit when talking
45 mA when paging (buzzing)
another station.
PA G E 2 IN S TRU C TI O N M A NUAL TH 1 0
+
+
+
_
_
_
B
CH
FUSE
1 Amp
12 V DC
OPERATIONAL
BUZZER OR
INDICATOR
LIGHT
STATION1STATION2STATION
3
STATION8STATION9STATION
10
1
2
3
4
5
6
7
8
9
10
+
_
B
-4-5-6-7-
CH
1
2
3
4
5
6
7
8
9
10
+
_
B
CH
1
2
3
4
5
6
7
8
9
10
+
_
B
CH
1
2
3
4
5
6
7
8
9
10
+
_
B
CH
1
2
3
4
5
6
7
8
9
10
+
_
B
CH
1
2
3
4
5
6
7
8
9
10
Figure 1
TH 1 0 IN S TRU C TI O N M A NUAL PA G E 3
A Division of
Head Office: SYDNEY- Locked Bag 2086, North Ryde, NSW 1670, Australia. Tel: +61 (0)2 9844 6666 Fax : +61 (0)2 9844 6600
MELBOURNE ADELAIDE PERTH BRISBANE SYDNEY AUCKLAND
7 Micro Circuit 14 Phillips Street Unit 1 Unit 1 Unit B Unit F
DANDENONG STH 3175 THEBARTON 5031 10-12 Harvard Way 89-101 Factory Road 22-24 College Street 35 Neilpark Drive
Tel: (03) 9798 0988 Tel: (08) 8234 2633 CANNING VALE 6155 OXLEY 4075 GLADESVILLE 2111 GREENMOUNT NZ
Fax: (03) 9798 0177 Fax: (08) 8234 5138 Tel: (08) 9455 5744 Tel: (07) 3278 6444 Tel: (02) 9879 8888 Tel: (09) 274 0955
Fax: (08) 9455 3110 Fax: (07) 3278 6555 Fax: (02) 9816 4722 Fax: (09) 274 0959
For customers outside Australia and New Zealand please contact your local GME Distributor or email: export@gme.net.au
Part Number: 310352 Drawing Number: 42950-3
Website: www.gme.net.au
GME limit this warranty to the original purchaser of
the equipment.
GME warrant the TH10 to be free from defects in
material and workmanship for a period of twelve
(12) months from the date of purchase from their
authorised Dealer.
Should the product require servicing during this
period, all labour and parts used to effect repairs will
be supplied free of charge. GME reserve the right to
determine whether damage has been occasioned by
accident, misuse or improper installation whereby
the warranty would be void, including equipment
which has been damaged due to:
(a) Reverse polarity connection to a battery
or power supply.
(b) Connection to an incorrect supply voltage.
(c) Non factory modification or repairs.
(d) Use of incorrect or replacement fuse.
(e) Lightening strike or static discharge.
Procedure to be followed by claimant: In the event
of a defect occurring during the warranty period,
the original Purchaser may return the defective
unit along with suitable proof of purchase date
(i.e. receipt, docket, credit card slip etc.) and a full
description of the defect to the Dealer from whom
the unit was purchased. All freight charges incurred
for transportation by the Dealer or GME are the
Purchaser’s responsibility.
GME AFTER SALES SERVICE
Your GME product is especially designed for the
environment encountered in domestic or marine
installations. The use of all solid state circuitry, careful
design and rigorous testing, result in high reliability.
Should failure occur however, GME maintain a fully
equipped service facility and spare parts stock to
meet the Customer’s requirements long after expiry
of the warranty period.
WARRANTY
Loading...