SPK008
6x9 4 WAY WAKE ToWER
SPEAKER SYSTEM
INSTRUCTION LEAFLET
INSTALLATION INSTRUCTIONS
The wake tower speaker is designed to hang from a wake
tower of diameter ranging from 40–50 mm (1.5”–2”).
ATTACHING THE SPEAKER TO THE WAKE TOWER
1. Remove both nuts holding the top plate onto the
bracket using a 4.75 mm (0.2”) allen key.
2. Remove the top plate.
3. Place the speaker and the top of the bracket around the
wake tower in desired
position. Screw in the nuts.
Self-adhesive
rubber pad
SPEAKER CABLE WIRING
1. Take the two (2) supplied rubber grommets and snip off
the end so a hole the diameter of your speaker cable
is made. GME recommends the use of 6–10 mm (0.2”
–0.4”) speaker cable depending on the cable run to
your stereo or amp.
Speaker wire diameter
2. Place the rubber grommet over the end of the speaker
cable. This needs to be done twice for each terminal on
the speaker.
3. Once the grommets have been placed over the speaker
wire, attach the wires to the terminals on the back of
the speaker.
4. Ensure the positive speaker cable is attached to the red
terminal and the negative speaker cable is attached to
the black terminal.
5. Slide the rubber grommet over the terminal, ensure the
whole of the terminal is covered.
Terminal
Grommet
4. Ensure the speakers are facing in the desired direction
Speaker Wire
and tighten.
Once the speaker has been attached to the wake tower, the
speaker cables can be attached.
SPK008 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK008
6. Connect the other end of the speaker wire to your amp
or stereo system.
SPEAKER DRIVER SPECIFICATIONS
System - mm (inches) 152 x 229 (6” x 9”)
Power Watts 210
Tweeter - mm (inches) 13 (½”) Neo PEI dome x 2
Midrange - mm (inches) 51 (2”) mylar cone
Efficiency (1M/1W) db 91
Frequency Response 60 Hz–22 kHz
Impedance (Ohms) 4
Weight - kgs (lbs) 4.15 (9.1)
WARRANTY
GME limit this warranty to the original purchaser of the
equipment.
GME warrant the SPK008 to be free from defects in material and
workmanship for a period of thirty six (36) months from the date
of purchase from their authorised retailer.
Should the product require servicing during this period, all labour
and parts used to effect repairs will be supplied free of charge.
GME reserve the right to determine whether damage has been
occasioned by accident, misuse or improper installation whereby
the warranty would be void, including equipment which has been
damaged due to:
(a) Incorrect or reverse polarity connection to a battery or power
supply or to an incorrect supply voltage.
(b) Operation without an antenna or by connection to an
antenna which has been incorrectly installed, resulting in
damage to the speaker’s output circuit.
SPK008
Procedure to be followed by claimant: In the event of a
defect occurring during the warranty period, the original purchaser
may return the defective unit along with suitable proof of purchase
date (i.e. receipt, docket, credit card slip etc.) and a full description
of the defect to the retailer from whom the unit was purchased. All
freight charges incurred for transportation by the retailer or GME
are the purchaser’s responsibility.
GME AFTER SALES SERVICE
Your speaker is especially designed for the environment
encountered in land and marine installations. The use of all
solid state circuitry, careful design and rigorous testing, result in
high reliability. Should failure occur however, GME maintain a
fully equipped service facility and spare parts stock to meet the
customer’s requirements long after expiry of the warranty period.
(c) Effects of water or moisture penetration.
(d) Non-factory modifications.
SPK008 TECHNICAL SPECIFICATION AND CUTTING TEMPLATE SPK008
Part Number: 310437 Drawing Number: 44317-2
SPK008
Loading...