GIGABYTE GV-NX79G256DP-RH Owner's Manual

VGA Card

GV-NX79G256DP-RH

Sept. 11, 2006

VGA Card

GV-NX79G256DP-RH

Sept. 11, 2006

GV-NX79G256DP-RH

GeForce™ 7900 GS Graphics Accelerator

User's Manual

Rev. 101

12MD-NX79G2PR-101R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Copyright

© 2006 GIGABYTE TECHNOLOGY CO., LTD

Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any form

without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the property of their respective owners.

Notice

Please do not remove any labels on VGA card, this may void the warranty of this VGA card

Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a

commitment to update the information contained herein.

Macrovision corporation product notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing

uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Table of Contents

English

1. Introduction ......................................................................................... 3

2. Hardware Installation ........................................................................... 4

3. Software Installation .......................................................................... 10

4. Troubleshooting Tips ........................................................................ 28

1.1. Features ..................................................................................................... 3

1.2. Minimum System Requirements ................................................................... 3

2.1. Board Layout .............................................................................................. 4

2.2. Hardware Installation ................................................................................... 6

3.1. Windows® XP Driver and Utilities Installation ............................................... 10

3.1.1. Operating System Requirement ................................................................................. 10

3.1.2. DirectX Installation ......................................................................................................... 11

3.1.3. Driver Installation .......................................................................................................... 12

3.1.4. Taskbar Icon ................................................................................................................. 14

3.1.5. Display Properties pages ............................................................................................ 15

3.1.6. nView Properties pages .............................................................................................. 22

3.2. Windows® 2000 driver installation .............................................................. 27

5. Appendix .......................................................................................... 29

5.1. Reflash BIOS in MS-DOS Mode ................................................................ 29

5.2. Connecting to a HDTV .............................................................................. 30

5.3. Resolutions and Color Depth Table (In Windows® XP) ............................... 31

GV-NX79G256DP-RH Graphics Accelerator

- 2 -

1. Introduction

1.1. Features

• Powered by NVIDIA® GeForce™ 7900 GS Graphics Processing Unit (GPU)

• Supports the newest PCI Express x16

• Integrated with 256 MB GDDR3 memory

• Supports DirectX 9.0c

• Supports NVIDIA® SLI™ (Scalable Link Interface) technology

• Supports AV / S-Video and HDTV output

• Supports TV-Out connector

• Supports 2 DVI-I connectors

• Supports D-sub connector (by adapter)

1.2. Minimum System Requirements

• IBM® or 100% PC compatible with Intel® Pentium® III 650 MHz or

AMD Athlon™ 650 MHz class processor or higher

• One PCI Express x16 slot

• Operating Systems Windows® 2000 / Windows® XP

• 64 MB system memory

• 50 MB of available disk space for full installation

• CD-ROM or DVD-ROM drive

• Minimum power supply 300 watt (To set up an SLI system with the graphics cards,

please use a power supply of 400 watt or above)

(Note)

English

(Note) SLI technology requires a PCI Express motherboard with two x16 physical connectors.

Graphics cards working in an SLI configuration must be with the same model name
(i.e. GV-NX79G256DP-RH) and from the same vendor (i.e. GIGABYTE TECHNOLOGY).

Introduction- 3 -

2.1. Board Layout

English

2. Hardware Installation

TV-out

DVI-I Connector 1

DVI-I Connector 2

HDTV

OR

NTSC / PAL TV Projector

OR

NTSC / PAL TV

Digital LCD Monitor

Analog LCD Monitor Analog Monitor

Projector

OR

DVI Output

Pb/AV Output

S-Video Output

GV-NX79G256DP-RH Graphics Accelerator

Y

Pr

TV-Out

DVI-I

Connector

1

DVI-I

Connector

2

DVI-I to D-Sub

Adapter

VGA Output

- 4 -

Expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some

precautions whenever you work on your computer.

1. Turn off your computer and unplug power supply.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

The card contains sensitive electric components, which can be easily damaged by static

electricity, so the card should be left in its original packing until it is installed.

Unpacking and installation should be done on a grounded anti-static mat. The operator

should be wearing an anti-static wristband, grounded at the same point as the anti-static

mat.

Inspect the card carton for obvious damage. Shipping and handling may cause damage

to your card. Be sure there are no shipping and handling damages on the card before

proceeding.

DO NOT APPLY POWER TO YOUR SYSTEM IF IT HAS BEEN DAMAGED ON

THE CARD.

In order to ensure your graphics card working correctly, please use official

Gigabyte BIOS only. Use none official Gigabyte BIOS might cause problem

on the graphics card.

English

Hardware Installation- 5 -

2.2. Hardware Installation

Installing Your graphics card.

English

Now that you have prepared your computer, you are ready to install your graphics accelerator

card.

To remove the existing graphics card:

1. Power off the computer and monitor, then

2. Remove the computer cover. If necessary,

disconnect the display cable from the back

of your computer.

consult your computer's manual for help in

removing the cover.

3. Remove any existing graphics card from

your computer.

Or, if your computer has any on-board

graphics capability, you may need to disable

it on the motherboard. For more information,

please see your computer documentation.

GV-NX79G256DP-RH Graphics Accelerator

- 6 -

To install your new graphics card:

1. Locate the PCI Express x16 slot. If necessary,

remove the metal cover from this slot; then

align your graphics card with the PCI

Express x16 slot, and press it in firmly until

the card is fully seated.

* Please make sure that the gold edge connectors of the graphics card is securely inserted.

2. Replace the screws to fasten the card in

place, and replace the computer cover.

After installation, please connect the power cable to your graphics card, or

the system will not boot.

3. Plug the display cable into your graphics
card; then turn on the computer and monitor.
To connect a flat panel directly to your
graphics card, use the DVI-I connector. To
connect a VGA monitor to the DVI-I
connector, plug the DVI-I to D-sub adapter
into the DVI-I connector, then plug the monitor

Connect a flat panel

cable into the adapter.

English

To TV / VCR

To Flat Panel Display

Connect a VGA monitor via DVI-I to D-sub adapter

You are now ready to proceed with the installation of the graphics card driver. Please refer

to next chapter for detailed instructions.

Hardware Installation- 7 -

GIGABYTE Video Adapter for Nvidia Graphics Cards

English

AV Out

S-Video Out

Connect to the TV-Out port
on the graphics card.

HDTV Component
(Y+Pr+Pb)

(1) Connecting HDTV

Connect your HDTV cables to the video adapter

according to the corresponding color.

(Y= Green, Pr= Red, Pb= Blue)

(2) Connecting S-Video

If your TV has a S-Video connection, connect the S-

Video cable from your TV to the S-Video Out port on the

adapter.

(3) Connecting AV Output

If your TV has a Composite video connection, you can

connect the RCA cable from your TV to the AV Out port

on the adapter.

GV-NX79G256DP-RH Graphics Accelerator

- 8 -

How NVIDIA® SLI™ (Scalable Link Interface) technology works:

In an SLI configuration, two SLI-ready graphics cards of the same model and the same manufacturers

are connected together via SLI bridge connector in a system that provides two x16 PCI Express slots

to scale graphics performance. The picture below shows that two graphics cards are linked in parallel

in an SLI configuration.

English

(provided by motherboard manufacturer)

SLI bridge connector

Two SLI-ready graphics cards of the same type.

(Example: GV-NX79G256DP-RH)

Hardware Installation- 9 -

3. Software Installation

English

In this manual, we assume that your CD-ROM Drive letter to be Drive D:

The installation of Windows® 2000 / Windows® XP drivers is very simple. When you insert the

driver CD into your CD-ROM drive, you can see the AUTORUN window (if it does not show

up, run "D:\setup.exe"). Then you can follow the guides to setup your graphics card driver.

(Please follow the subsection 3.1.3 "Driver installation" to install the driver for your graphics

accelerator.)

3.1. Windows® XP Driver and Utilities Installation

3.1.1. Operating System Requirement

• When loading the graphics card drivers for the system, please make sure your system

has installed DirectX 9.0c or later version.

• If you install the graphics card drivers for the motherboard, which consist of SIS or VIA

chipsets, please install the appropriate driver program for that motherboard. Or please

contact your motherboard nearest dealer for motherboard driver.

GV-NX79G256DP-RH Graphics Accelerator

- 10 -

3.1.2. DirectX Installation

Install Microsoft DirectX to enable 3D hardware acceleration support for Windows® 2000 or

Windows® XP to achieve better 3D performance.

0 Note: For software MPEG support in Windows® 2000 or Windows® XP, you must install

DirectX first. Users who run Windows® XP with Service Pack 2 or above do not need to

install DirectX separately.

Step 1.

When autorun window show up, click the Install

DirectX 9 item.

English

Step 2. Choose I accept the agreement

and click the Next button.

Installing the components.

Step 3. Click the Next button.

Step 4. Click Finish to restart computer.

Then the DirectX 9 installation is completed.

Software Installation- 11 -

3.1.3. Driver Installation

A. New hardware found

English

After the graphics card is inserted into your computer at the first time, the windows will

automatically detect a new hardware in the system and pop out a "New Hardware Found"

message. The following is the step-by-step installation guide.

Step 1: Found new hardware wizard: Video controller (VGA Compatible)

Step 2: Found new hardware wizard: Searching and installing

The wizard will search for the driver and install it automatically.

Click the "Next" button to install the driver. (There

is a driver CD disk that came with your graphics

accelerator, please insert it now.)

Or click the "Cancel" button to install the driver

from AUTORUN window.

Step 3: Found new hardware wizard: Finish

Click the "Finish" button to finish the installation.

GV-NX79G256DP-RH Graphics Accelerator

- 12 -

B. Driver installation (Autorun Window)

Insert the driver CD disk into your CD-ROM, and then you can see the AUTORUN window.

If it does not show up, please run "D:\setup.exe".

Step 1.

When autorun window show up, click the Display

Driver item.

Then click the Install Display Driver item.

English

Step 2. Click the Next button.

Windows installings the components.

Step 3. Click the Finish button to restart computer.

Then the driver installation is completed.

Software Installation- 13 -

3.1.4. Taskbar Icon

After installation of the display drivers, you will find a NVIDIA icon on the taskbar's status

area. Click this icon to open the control panel.

English

Right click the icon.

GV-NX79G256DP-RH Graphics Accelerator

You can adjust the properties of
the graphics accelerator from
here.

- 14 -

3.1.5. Display Properties pages

To access Display Properties pages, right-click the GIGABYTE icon on the taskbar and

select Display Properties or right-click on Desktop and then select Properties. The Display

Properties dialog box shows the information of display adapter, color, the range of display

area, and the refresh rate.

Settings (Resolutions and Color depth for Windows)

You may adjust the screen resolution and color quality settings in this dialog box.

You can move the slider to change the resolution.

You can click the item to change the color quality.

Click the Advanced button for adapter and setting.

To access more advanced options, click the Advanced button.

English

Software Installation- 15 -

GeForce 7900 GS tab

After pressing the Advanced button in Settings, you'll see the Plug and Play Monitor and NVIDIA

GeForce 7900 GS Properties dialog box. Click the GeForce 7900 GS tab. (You can also click the

English

NVIDIA icon on the taskbar and select Nvidia Display to access the GeForce 7900 GS properties

page.)

When you access the GeForce 7900 GS tab page

for the first time, you'll see two items in the left

submenu:
 Launch Page

All of the NVIDIA control panels have been
consolidated into a single application, the
NVIDIA Control Panel. Click the Start the
NVIDIA Control Panel button to open the
NVIDIA Control Panel.

In the NVIDIA Control Panel, select a category to
alter specific NVIDIA display settings.

GV-NX79G256DP-RH Graphics Accelerator

 Control Panel User Interface

You can choose one of the two user interfaces
below:

• Classic NVIDIA Control Panel

When you select this item and click Apply,
a submenu that provides the NVIDIA display
properties settings will appear on the left side.

• New NVIDIA Control Panel

This is the default user interface, which
provides control of the NVIDIA graphics driver
settings and other NVIDIA utilities you might
have installed on your system.

- 16 -

The following section introduces display properties settings using the classic NVIDIA control
panel interface as the example.

GeForce 7900 GS properties

 This page shows the Adapter, System and

Driver version information.

You can select other properties from the pop-out menu.

English

nView Display Settings properties

(Note)

 nView allows you to connect separate displays to single

graphics card.

• nView Display mode: select your preferred nView display
modes here.
Options: Single display/ Clone/ Horizontal Sapn/

Vertical Span/ Dual View

• Primary/Secondary display: select a single display or
display pair. The selected display combination will appear
in the graphical representation below.

• Make this the primary display: Specifies that the display
corresponding to the icon you selected above is the
primary display.

• Click Apply to apply settings or click OK to save settings.

 If TV is chosen as the display, you will need to select the

proper TV format. To do this, click Device Settings followed
by Select TV format. Select the format for your television
and then click Apply followed by OK.

Display

Matrix

Model GV-NX79G256DP-RH
CRT+TV Yes
CRT+DVI Yes
DVI+TV Yes
DVI+DVI Yes

(Note) Only Single display mode is available when SLI mode is enabled.

Software Installation- 17 -

Dual-Monitor Setup:

You can set the display to output from two monitors on the nView Display Settings page.

This graphics card supports the following modes:

English

(1) Clone Mode:

Clone mode indicates that both displays in the
display pair show images of the same desktop.
Select Clone from the nView Display Mode list
and click Apply.

(2) Horizontal Span Mode:

Horizontal Span mode indicates that both displays
in the display pair function as one wide virtual
desktop. The width of each display is half the
width of the total virtual desktop width.
Select Horizontal Span from the nView Display

Mode list and click Apply.

(3) Vertical Span Mode:

Vertical Span mode indicates that both displays in
the display pair function as one tall virtual desktop.
The height of each display is half the height of the
total virtual desktop height.
Select Vertical Span from the nView Display
Mode list and click Apply.

Clone Mode

Horizontal Span Mode

(4) Dual View Mode:

Dualview mode indicates that both displays in the
display pair function as one virtual desktop. Unlike
Horizontal Span or Vertical Span mode, Dualview
treats each display as a separate device. This
means that the taskbar will not be stretched across
displays and 3D applications are not accelerated
as efficiently as when the application spans
displays.
Select DualView from the nView Display Mode
list and click Apply.

GV-NX79G256DP-RH Graphics Accelerator

Vertical Span Mode

Dual View Mode

- 18 -

Performance and Quality Settings properties

 The sliders lets to decide whether your application should use

quality or high performance texture.

• Application profiles: Select the application profile from the list
of profiles.

• Global driver settings: Select the Settings item and move
the slider below to set the degree of antialiasing to used in
Direct3D and OpenGL applications.

• Antialiasing settings value: allows to set the degree of the
Global Driver Settings.

SLI multi-GPU *

 To enable SLI mode, select the Enable SLI multi-GPU

check box and click Apply after installation of two GV-

NX79G256DP-RH graphics cards on an SLI-capable

motherboard. Then restart your system when prompted.

English

Color Correction properties

"*" Only Windows® XP operating system supports the SLI mode.

Please do not enable SLI multi-GPU in Windows

 The Color Correction Properties is used to compensate for

variations in luminance between a source image and its output

on a display device. Adjust the color correction settings to

provide more accurate color reproduction of images (such as

photographs) on your display device. Also, many 3D-

accelerated games may appear too dark to play. Increasing

the brightness and/or the gamma value equally across all

channels makes these games appear brighter and more

playable.

®

2000.

Software Installation- 19 -

Video Overlay Settings properties

English

Tools properties

 The Video Overlay Settings Properties can adjust Overlay

zoom controls and Overlay color controls. There is only one

video overlay, which is only available on the Primary display.

The video overlay controls are automatically activated during

playback of any video file type that supports overlay

adjustments. The "Adjust Colors" button will access "Color

Correction" properties page.

 The NVIDIA settings taskbar utility lets you conveniently access

various features and presets you've configured in the Display

Properties directly from the Windows taskbar.

• Shortcut tools

The Desktop Manager provides enhanced nView multi-

display functionality and helps you organize your applications

for use with multiple displays and desktops.

• Display optimization

Run the Display Optimization Wizard to adjust your

display(s) for optimal viewing and representation of colors.

• Troubleshooting

This option can be used to force detection of an attached TV

set which does not report its presence to the graphics card.

NV Rotate properties

 The NV Rotate Properties is used to rotate the screen. If your

monitor is capable of operating in either Landscape or Portrait

mode, you can adjust the screen by this properties.

• Landscape (0 degree rotation)

• Portrait (90 degree rotation)

• Inverted landscape (180 degree rotation)

• Inverted portrait (270 degree rotation)

GV-NX79G256DP-RH Graphics Accelerator

- 20 -

Temperature Settings properties

 The Temperature Properties can auto detected the GPU

Core temperature. You can select the Notify when GPU core

temperature exceeds threshold check box.

Screen Resolutions & Refresh Rates properties

 The Screen Resolutions & Refresh Rates Properties allows

you to adjust the screen resolution, color quality and monitor

settings (screen refresh rates). Or you can customize resolutions

and refresh rates.

English

Menu Editing properties

 The Menu Editing Properties can remove infrequently used

screens by dragging them from the screen menu to the list

below. Restore screens to the menu by dragging them

individually, or click Restore Defaults.

To begin, select the Enable menu editing check box. To

return to normal navigation mode, do not select the check box.

Software Installation- 21 -

3.1.6. nView Properties pages

nView is a set of desktop tools designed to help you be more productive when using your

graphics card. With nView you can set up multiple desktops to work with your applications.

English

Multiple desktops give you extra desktop areas on which to run your applications so you

won't have to crowd several open application windows on one desktop.

Enable the nView Desktop Manager features:

Right-click on desktop and choose Properties>Settings>Advanced>GeForce 7900 GS>

Desktop Management

Access nView properties page:

To access the nView properties page, you can click the NVIDIA icon on the taskbar and

select nView Properties under nView Destop Manager (Method A). Or right-click on

Desktop, select Properties>Settings>Advanced>GeForce 7900 GS. Double-click Desktop

Management item on the pop-up menu (Method B).

Click the "Enable" button to turn on all the nView Desktop
Manager features.

Method A: Method B:

Click the item to start nView Properties.

GV-NX79G256DP-RH Graphics Accelerator

Double-click Desktop Management to see
more nView properties.

- 22 -

nView Desktop Management properties

 This tab contains information about the nView Desktop Manager.

The setup wizard can also be accessed from this tab.

nView Profiles properties

 This tab contains a record all nView display settings for easy

software setup.

English

nView Windows properties

 This tab allows you to control window and dialog box placement

when using multiple monitors.

Software Installation- 23 -

nView Applications properties

English

nView Desktops properties

 This tab allows you to control nView settings depending different

applications.

 This tab allows you to create up to 32 unique desktops.

nView User Interface properties

 This tab allows for customization of the nView user interface.

GV-NX79G256DP-RH Graphics Accelerator

- 24 -

nView Effects properties

nView Zoom properties

English

 This tab provides special windows effects that you can apply

to your applications.

 This tab provides dynamic zoom functionality on the desktop.

Also enables full screen video playback via the video mirroring

control button.

nView Hot Keys properties

 This tab lets you perform various actions with shortcut keys or

key combinations.

Software Installation- 25 -

nView Mouse properties

English

nView Tools properties

 This tab can modify and extend mouse behavior with kinematic

actions.

 This tab can improve nView functionality for mobile and desktop

users.

GV-NX79G256DP-RH Graphics Accelerator

- 26 -

3.2. Windows® 2000 driver installation

With Windows running on your computer, you need to install the graphics card driver to take

advantage of the higher performance, resolutions, and special graphics features of the

graphics card. To ensure you install the latest driver, insert the Installation CD that shipped

with your graphics card.

To install the graphics card driver for Windows® 2000, please insert the Installation CD. Then

the AUTORUN window will show up. Click Install Display Driver item, and follow the

wizard to install the driver.

If Windows® does not show the CD automatically, please run following steps:

1. Click the Start button on the control bar.

2. Select Run.

3. Type the following: D:\SETUP.exe

(If D is not your CD-ROM drive, substitute D with the correct drive letter.)

4. Click "OK".

5. Click on "Install Display Drivers" to begin the Installation Wizard.

6. Click "Next".

7. Click "Yes" to the license agreement.

8. Follow the Wizard's on-screen instructions to complete the installation.

English

Please make sure the Windows® 2000 have installed Windows® 2000 Service

Pack (or later) before installing the graphics accelerator driver.

Software Installation- 27 -

4. Troubleshooting Tips

English

The following troubleshooting tips may help if you experience problems. Contact your dealer

or Gigabyte for more advanced troubleshooting information.

 Check that the card is seated properly in the PCI Express x16 slot.

 Ensure that the display cable is securely fastened to the card's display connector.

 Make sure that the monitor and computer are plugged in and receiving power.

 If necessary, disable any built-in graphics capabilities on your motherboard. For

more information, consult your computer's manual or manufacturer.

(NOTE: Some manufacturers do not allow the built-in graphics to be disabled or to

become the secondary display.)

 Make sure you selected the appropriate display device and graphics card when you

installed the graphics driver.

 Restart your computer. Press the F8 key on your keyboard after system starts up.

When the Windows Advanced Options Menu appears, select Safe Mode and press

Enter. After getting into Safe Mode, in Device Manager check whether the driver for

the graphics card is correct.

 For more assistance, use the Troubleshooting Guide located in the Windows® Help or

contact your computer manufacturer.

If necessary, adjust your monitor's setting by monitor's adjust panel to make the

screen looks focused, crisp, and sharp. (Please refer to the monitor's manual.)

GV-NX79G256DP-RH Graphics Accelerator

- 28 -

5. Appendix

5.1. Reflash BIOS in MS-DOS Mode

1. Extract the downloaded Zip file to your hard disk(s) or floppy disk. This procedure assumes drive A.

2. Restart the computer in MS-DOS mode. (For Windows

the computer in MS-DOS mode.)

3. Change the command prompt to A:\>.

4. To back up the current BIOS, at the A:\> prompt, type[BIOS flash utility name]

-s [BIOS file name] (example: gvf18 -s X79G8DPR.f1) and press Enter.

5. To flash BIOS, at the A:\> prompt, type [BIOS flash utility name] -p [BIOS

file name] (example: gvf18 -p X79G8DPR.f2) and press Enter.

6. Wait until it's done, then restart your computer.

®

2000/XP, you need a startup disk to restart

English

Appendix- 29 -

5.2. Connecting to a HDTV

Use the included component video adapter to connect a HDTV to the graphics card.

English

Step 1:

Connect the HDTV component cable to the adapter

according to the corresponding color. (Y= Green, Pr=

Red, Pb= Blue). Connect the TV Out cable from the

adapter to the TV Out port on your graphics card.

Step 2:

After installation of the graphics card driver, right-click on

Desktop and select Properties. When Display

Properties dialog box appears, select the Settings

tab. In Settings, click the Advanced button.

Step 3:

Click the Geforce 7900 GS tab when advanced

properties dialog box appears. Select n-Viewe Display

Settings from the side menu and select HDTV from the

Current display list. Then click Apply.

Step 4:

Right-click on the HDTV icon and select TV format

depending on your HDTV. Then click Apply to complete

the settings.

GV-NX79G256DP-RH Graphics Accelerator

- 30 -

5.3. Resolutions and Color Depth Table (In Windows® XP)

GeForce 7900 GS Single Display Standard Modes

Display Refresh Color Depth (bpp)

Screen Rate 8bpp(256 color) 16bpp(65K color) 32bpp(16.7M)

Resolution (Hz) Standard mode High mode True mode

320 x 200 60~75 333
320 x 240 60~75 333
400 x 300 60~75 333
480 x 360 60~75 333
512 x 384 60~75 333
640 x 400 (16:10) 60~75 333
640 x 480 60~240 333
720 x 480 60 333
720 x 576 50~60 333
800 x 600 60~240 333
848 x 480 60~240 333
960 x 600 (16:10) 60~240 333
1024 x 768 60~200 333

240 33X

1088 x 612 (16:9) 60~200 333

240 33X

1152 x 864 60~170 333

200 33X

1280 x 720 (16:9) 60~150 333

170 33X

1280 x 768 60~150 333

170 33X

1280 x 960 60~150 333

170 33X

1280 x 1024 60~150 333

170 33X

1360 x 768 60~150 333

170 33X

1600 x 900 (16:9) 60~120 333

140~150 33X

1600 x 1024 60~100 333

120 33X

English

To be continued...

Appendix- 31 -

Display Refresh Color Depth (bpp)

English

Screen Rate 8bpp(256 color) 16bpp (65K color) 32bpp (16.7M)

Resolution (Hz) Standard mode High mode True mode

1600 x 1200 60~100 333

1920 x 1080 (16:9) 30~85 333

1920 x 1200 (16:10) 60~85 333

1920 x 1440 60~85 333
2048 x 1536 60~85 333
2560 x 1600 60 333

(Dual-Link)

120 33X

100 33X

100 33X

* This table is for reference only. The actual resolutions supported depend on the monitor you use.

GV-NX79G256DP-RH Graphics Accelerator

- 32 -