Gigabyte GA-6JIEV-RH User Manual

USER’S MANUAL

GA-6JIEV-RH

Intel® mini-ITX Motherboard

Intel

®

mini-ITX Motherboard

Rev. 1001

* The WEEE marking on the product indicates this product must not be disposed of with

user's other household waste and must be handed over to a designated collection point
for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Copyright

© 2007 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in the manual are legally registered to their respective companies.

Notice

The written content provided with this product is the property of Gigabyte.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any
means without Gigabyte's prior written permission. Specifications and features are subject to change
without prior notice.

Product Manual Classification

In order to assist in the use of this product, Gigabyte has categorized the user manual in the
following:

 For detailed product information and specifications, please carefully read the

"Product User Manual".

 For detailed information related to Gigabyte's unique features, please go to "T echnology

Guide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

3

GA-6JIEV-RH Motherboard

Table of Content

Item Checklist ........................................................................................4

Chapter 1Introduction.............................................................................5

1-1Considerations Prior to Installation........................................................ 5

1.2Features Summary................................................................................. 6

1.3Motherboard Components..................................................................... 8

Chapter 2Hardware Installation Process................................................9

2-1: Installing Processor Colling Fan.......................................................... 9

2-2: Installing Memory Module..................................................................10

2-3: Connect ribbon cables, cabinet wires, and power supply ................ 11

2-3-1 : I/O Back Panel Introduction.................................................................................11

2-4: Connectors Introduction & Jumper Setting........................................14

2-5: Block Diagram...................................................................................22

Chapter 3 BIOS Setup ..........................................................................23

The Main Menu (For example: BIOS Ver. : F1) .......................................................... 24

3-1Standard CMOS Features......................................................................................... 26

3-2Advanced BIOS Features ......................................................................................... 28

3-3Integrated Peripherals ................................................................................................ 30

3-4Power Management Setup........................................................................................ 32

3-5PC Health Status ........................................................................................................ 33

3-6F re que nc y/V ol tag e C on tro l ....................................................................................... 34

3-7Load Fail-Safe Defaults.............................................................................................. 35

3-8Load Optimized Defaults............................................................................................ 35

3-9Set Supervisor/User Password ............................................................................... 36

3-10Save & Exit Setup ................................................................................................... 37

3-11Exit Without Saving.................................................................................................. 37

3-12Flash BIOS Method Introduction ............................................................................. 38

4

Introduction

; The GA-6JIEV-RH motherboard
; I/O Shield Kit
; CD for motherboard driver & utility
; GA--6JIEV-RH Quick Reference Guide
; Power cable x 1
; B4P/S4P Cable x 1
; Optional Power Adapter x 1

Item Checklist

* The items listed above are for reference only, and are subject to change without notice.

5

GA-6JIEV-RH Motherboard

Chapter 1 Introduction

1- 1 Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the
instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components
(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or
within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply connector
from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are
required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the
information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the
motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard
or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,
please consult a certified computer technician.

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

6

Introduction

1.2 Features Summary

Form Factor y 170mm x 170mm Mini ITX form factor, 8 layers PCB.
CPU y Supports single Intel® ULV CeleronM processor

y Supports 600MHz

Chipset y Intel® 910GMLE MCH

y Intel

®

ICH6M

Memory y 1 x DDR2 DIMM SO-DIMM socket

y Supports up to 2GB 400 memory
y Supports 1.8V DDR2 DIMMs

I/O Control y ITE IT8712F Super I/O
Expansion Slots y Supports 1 PCI slot 32-Bit/33MHz

y Supports 1 mini card slot (PCI-E x1/ USB 2.0)
SA TA Controller y Intel® ICH6M
On-Board Graphic y Build in Intel® 910GMLE chipset

y Shared system memory up to 128MB
On-Board Sound y Relteak® ALC 883 chipset
Internal Connector y 1 x 4-pin ATX power connector

y 2 x SAT A connectors

y 1 x IDE connector

y 2 x Serial connectors (COM)

y 1 x front audio connector

y 1 x USB 2.0 connectors for additional 2 ports by cable

y 1 x front panel connecctor

y 1 x System fan cable connector

y 1 x CPU fan cable connector
Rear Panel I/O y 1 x DC power jack

y 1 x VGA port

y 1 x COM port

y 4 x USB 2.0 ports

y 2 x LAN RJ45 ports

y 1 HD Audio jacks (Line-out / MIC-in / Line-in) can configure 5.1

channel output by utility

Hardware Monitor y Enhanced features with CPU Vcore, 1.5V reference,

VCC3 (3.3V) , VBAT3V, +5VSB, CPUA/B Temperature, and
System T emperature V alues viewing

y CPU/System Fan Revolution Detect

y CPU shutdown when overheat

7

GA-6JIEV-RH Motherboard

On-Board LAN y Atheros 8121 GbE LAN controller

y Supports WOL, PXE
BIOS y AWARD BIOS on 8Mb SPI Flash ROM
Additional Features y External Modem wake up

y Supports S1, S3, S4, S5 under Windows Operating System

y Wake on LAN (WOL)

y Supports Console Redirection

y Supports 4-pin Fan controller

8

Introduction

1.3 Motherboard Components

CPU

Intel

910GMLE

Intel

ICH6M

F_AUDIO1

PCI 32/33MHz

Battery cable adapter

Audio jack

USB
LAN

USB
LAN

Relteak

ALC883

COM2

Atheros 8121

VGA

DDR1

Mini PCI

GPIO connector

ATX 12V

Power

DC

Power

Jack

SATA1

SATA2

PWR_FAN1

CF

Connector

CPU Fan

F_Panel

F_USB1

IDE1

COM

PWR_FAN2

SYS_FAN

ITE

IT8712

BIOS

9

GA-6JIEV-RH Motherboard

Chapter 2 Hardware Installation Process

2-1: Installing Processor Colling Fan

!

!

WARNING!

To prevent the CPU overheat, please make sure you have apply the CPU
cooler paste on the surface of installed CPU

Step 1 Attach the heat sink n the procssor socket. Secure the cooing fan with screws.
Step 2 Connect processor fan can cable to the processor fan connector.

1

1

1

2

10

Hardware Installation Process

2-2: Installing Memory Module

The motherboard supports DDR2 memory module, whereby BIOS will automatically detect memory
capacity and specifications. The memory module only can be inserted in one direction.

Before installing the memory modules, please comply with the following conditions:

1. Please make sure the computer power is switched off before installing or removing
memory modules.

Installation Steps:

Step 1. Align the memory with the DIMM module and insert the DIMM memory module into the DIMM

slot. Please note that memory module has a foolproof insertion design. A memory module can
be installed In only one direction.

Step 2. Push down the memory to seat it firmly.

2

1

Table 1. Supported DIMM Module Type

Size Organization RAM Chips/DIMM

256MB 8MB x 8 x 4 bks 8

16MB x 16 x 4bks 16

512MB 16MB x 8 x 4bks 8

32MB x 16 x 4bks 16

1GB 32MB x 8 x 4bks 8

64MB x 16 x 4bks 16

2GB 32MB x 8 x 4bks 8

64MB x 16 x 4bks 16

11

GA-6JIEV-RH Motherboard

2-3: Connect ribbon cables, cabinet wires, and power
supply

2-3-1 : I/O Back Panel Introduction

12

Hardware Installation Process

DC Power Jack

Connect the DC power to this port.

VGA Port

Connect the monitor cable to this port.

COM Port

Modem can be connected to Seri

al port.

LAN Port

The LAN port provides Internet connection of Gigabit Ethernet with data transfer speeds of
10/100/1000Mbps.

USB

Before you connect your device(s) into USB connector(s), please make sure your device(s) such
as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.
Also make sure your OS supports USB controller. If your OS does not support USB controller,
please contact OS vendor for possible patch or driver updated. For more information please
contact your OS or device(s) vendors.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround
speakers can be connected to Line Out (Front Speaker Out) jack.

MIC In

The default MIC In jack. Microphone must be connected to MIC In jack.

13

GA-6JIEV-RH Motherboard

LAN LED Description

LED1 (Green)

LED2 (Green/Yellow)

Color Condition Description

Green ON LAN Link / no Access
Green BLINK LAN Access

- OFF Idle

- OFF 10Mbps connection

- OFF Port identification with 10 Mbps connection
Green ON 100Mbps connection
Green BLINK Port identification with 100Mbps connection
Yellow ON 1Gbps connection
Yellow BLINK Port identification with 1Gbps connection

Name

LED1

LED2

14

Connector Introduction

2-4: Connectors Introduction & Jumper Setting

1. ATX12 8. CPU_FAN1

2. IDE1 (IDE cable connector) 9. SYS_FAN1

3. SATA1 (SATA cable connector) 10. PWR1

4. SATA2 (SATA cable connector) 1 1 . PWR2

5. COM2 12. GPIO

6. F_USB1 (Fornt USB cable connector) 13. F_Panel (Front Panel connector)

7. F_AUDIO1 14. CLR_CMOS (Clear CMOS)

1

2

3

4

5

6

7

8

10

11

9

12

13

14

15

GA-6JIEV-RH Motherboard

1 ) ATX12 (Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the
components on the motherboard. Before connecting the power connector, please make sure that
all components and devices are properly installed. Align the power connector with its proper
location on the motherboard and connect tightly.
The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power
connector is not connected, the system will not start.
Caution! Please use a power supply that is able to handle the system voltage requirements. It is
recommended that a power supply that can withstand high power consumption be used (300W or
greater). If a power supply is used that does not provide the required power, the result can lead to an
unstable system or a system that is unable to start. If you use a power supply that provides a 24-pin A TX
power connector, please remove the small cover on the power connector on the motherboard before
plugging in the power cord; otherwise, please do not remove it.

13

2

4

Pin No. Definition

1 GND
2 GND
3 +12V
4 +12V

16

Connector Introduction

SATA 3Gb/s can provide up to 300MB/s stransfer rate. Please refer to the BIOS setting for the
SATA 3Gb/s and install the proper driver in order to work properly .

3/ 4 ) SA TA 1/2 (Serial ATA cable connectors)

Pin No. Definition

1 GND
2TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND

17

2 ) IDE1 (IDE cable connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect
to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or
optical drive). If you want to connect two IDE devices, please set the jumper on one IDE device
as Master and the other as Slave (for information, please refer to the instructions located on the IDE
device).
Before attaching the IDE cable, please take note of the foolproof groove in IDE connector.

391

240

17

GA-6JIEV-RH Motherboard

5 ) COM2

Pin No. Definition

1 DCD­2 SIN2
3 SOUT2
4 DTR2­5 GND
6 DSR2­7 RTS2­8 CTS2­9 RI2­10 N C

19

102

Be careful with the polarity of the front USB connector. Check the pin assignment carefully while
you connect the front USB cable, incorrect connection between the cable and connector will make
the device unable to work or even damage it. For optional front USB cable, please contact your
local dealer.

6 ) F_USB1 (Front USB cable connector)

2

1

10

9

Pin No. Definition

1 Power
2 Power
3 USB Dx­4 USB Dy­5 USB Dx+
6 USB Dy+
7 GND
8 GND
9 No Pin
10 NC

18

Connector Introduction

7) F_AUDIO1 (Front AUDIO connector)

If you want to use Front Audio connector , you must remove 5-6, 9-10 Jumper . In order to utilize the
front audio header, your chassis must have front audio connector . Also please make sure the pin
assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis
you are buying support front audio connector, please contact your dealer.

8/9) CPU_FAN1/SYS_FAN1 (CPU fan/System fan cable connectors)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN) power
connector and possesses a foolproof connection design.
Most coolers are designed with color-coded power connector wires. A red power connector wire
indicates a positive connection and requires a +12V power voltage. The black connector wire is the
ground wire (GND).
Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_F AN connector to prevent
CPU damage or system hanging caused by overheating.

SYS_FAN1

CPU_FAN1

1

Pin No. Definition

1 GND
2 12V
3 Sense
4 Control

Pin No. Definition

1 MIC_L
2 GND
3 MIC_R
4 -ACZ_DEC
5 Line_R
6 GND
7 Faudio_JD
8 No Pin
9 Line_L
10 GND

2

9

1

10

19

GA-6JIEV-RH Motherboard

12) GPIO (GPIO connector)

9/10) PWR1/PWR2 (Power Output connector)

1

PWR2

PWR1

Pin No. Definition

1 12V
2 GND
3 GND
45V

1

1

9

Pin No. Definition

1 GPO50
2 GPO24
3 GPO11
4 GPO37
5 GPI11
6 GPI26
7 GPI1
8 No Pin
9 GPI0

20

Connector Introduction

13 ) F_Panel (2X10 Pins Front Panel connector)

Please connect the power LED, PC speaker, reset switch and power switch of your chassis
front panel to the F_PANEL connector according to the pin assignment above.

20

19

2

1

Pin No. Signal Name Description

1. HD+ Hard Disk LED Signal anode (+)

2. MSG+ Message LED Signal anode (+)

3. HD- Hard Disk LED Signal cathode(-)

4. MSG- Message LED Signal cathode(-)

5. RES- Reset Button anode (+)

6. PW+ Power Button Signal cathode(-)

7. RES+ Reset Button cathode(-)

8. PW- Power Button Signal anode (+)

9. NC No connect

10. No Pin Pin removed
11 . No Pin Pin removed

12. No Pin Pin removed

13. No Pin Pin removed

14. Speaker+ Speaker LED Signal anode (+)

15. No Pin Pin removed

16. NC No connect

17. No Pin Pin removed

18. NC No connect

19. No Pin Pin removed

20. Speaker- Speaker LED Signal cathode(-)

21

GA-6JIEV-RH Motherboard

Y ou may clear the CMOS data to restore its default values by this jumper .

Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To
clear CMOS, temporarily short 1-2 pin.

17 ) CLR_CMOS1 (Clear CMOS Function)

1-2 Close: Clear CMOS

2-3 Close: Normal operation(Default setting)

1

1

Block Diagram

22

2-5: Block Diagram

CPU
Intel

Celeron-M

NB

Intel 910GMLE

SB

Intel

ICH6-M

Audio In

PCI-E Bus

LPC

Clock

Generator

Cypress

CY184260XC

CPU CLK

Host Bus

Clock
Buffer

ICS9DB106

DDR2 400 SO-DIMM

DMI

SI/O

ITE

IT8712F

ATA HDD connector

Primary

P-ATA

SATAx2

USB4,5

LPC CLK 33MHz

Hardware Monitor Circuits

CPU

FAN

SYS

FAN

BIOS

4M

LPC

LPC 48MHz

HD Audio

Codec

ALC833

Audio Out

MIC

CF card connector

HD Audio

LAN

Atheros

AR8112

Atheros

AR8216

Switch

VGA connector

RJ45
USB2
USB3

PCI 32/33MHz Slot

PCI Bus

Mini Card connector

LAN

Atheros

AR8121

RJ45
USB0
USB1

Front Audio

connector

CHA

S-ATA

USB 2.0

PCI-E Bus

FWH 33MHz

GA-6JIEV-RH Motherboard

23

BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure
required settings or to activate certain system features.
The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS
SRAM.
When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will
take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".
If you wish to upgrade to a new BIOS, or GIGABYTE's Q-Flash utilitycan be used.
Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating
system.

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu / Option Page Setup Menu

Press <F1> to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.

Chapter 3 BIOS Setup

Because BIOS flashing is potentially risky, please do it with caution and avoid inadequate
operation that may result in system malfunction.

CONTROL KEYS

< >< >< >< > Move to select item
<Enter> Select Item
<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main Menu
<Page Up> Increase the numeric value or make changes
<Page Down> Decrease the numeric value or make changes
<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu
<F2> Item Help
<F5> Restore the previous CMOS value from CMOS, only for Option Page Setup

Menu
<F6> Load the Fail-safe default CMOS value from BIOS default table
<F7> Load the Optimized Defaults
<F8> Q-Flash utility
<F9> System Information
<F10> Save all the CMOS changes, only for Main Menu

BIOS Setup

24

1. If you don't find the settings you want, press "Ctrl+F1" to access advanced options.

2. Select the Load Optimized Defaults item in the BIOS Setup when somehow the system
is not stable as usual. This action makes the system reset to the default settings for
stability.

3. The BIOS Setup menus described in this chapter are for reference only and may differ from
the exact settings for your motherboard.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PC Health Status
` Frequency/Voltage Control

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

The Main Menu (For example: BIOS Ver. : F1)

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the
screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

GA-6JIEV-RH Motherboard

25





 Standard CMOS Features

This setup page includes all the items in standard compatible BIOS.





 Advanced BIOS Features

This setup page includes all the items of Award special enhanced features.





 Integrated Peripherals

This setup page includes all onboard peripherals.





 Power Management Setup

This setup page includes all the items of Green function features.





 PC Health Status

This setup page is the System auto detect Temperature, voltage, fan, speed.





 Frequency/Voltage Control

This setup page is control CPU clock and frequency ratio.





 Load Fail-Safe Defaults

Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe
configuration.





 Load Optimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would be in
best performance configuration.





 Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup, or just
to Setup.





 Set User Password

Change, set, or disable password. It allows you to limit access to the system.





 Save & Exit Setup

Save CMOS value settings to CMOS and exit setup.





 Exit Without Saving

Abandon all CMOS value changes and exit setup.

BIOS Setup

26

3- 1 Standard CMOS Features

Date

The date format is <week>, <month>, <day>, <year>.

Week The week, from Sun to Sat, determined by the BIOS and is display-only
Month The month, Jan. Through Dec.
Day The day, from 1 to 31 (or the maximum allowed in the month)
Year The year, from 2000 through 2099

Time

The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00.

IDE Channel 0 Master/Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.
IDE Channel 0 Master/Slave

IDE devices setup. You can use one of three methods:

• Auto Allows BIOS to automatically detect IDE/SATA devices during POST. (Default
value)

• None Select this if no IDE/SATA devices are used and the system will skip the
automatic detection step and allow for faster system start up.

• Manual User can manually input the correct settings.

Access Mode Use this to set the access mode for the hard drive. The four options are:

CHS/LBA/Large/Auto(default:Auto)

Capacity Capacity of currectly installed hard drive.

IDE Channel 2 Master

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.
Extended IDE Drive You can use one of the two methods:

• Auto Allows BIOS to automatically detect IDE/SATA devices during POST(default)

• None Select this if no IDE/SATA devices are used and the system will skip the
automatic detection step and allow for faster system start up.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Standard CMOS Features

Date (mm:dd:yy) Wed, May 21 2008
Time (hh:mm:ss) 14:31:24

` IDE Channel 0 Master [None]
` IDE Channel 0 Slave [None]
` IDE Channel 2 Master [None]

Base Memory 640K
Extended Memory 239M
Total Memory 1015M
BIOS Version F1

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help
Menu Level`

GA-6JIEV-RH Motherboard

27

Access Mode Use this to set the access mode for the hard drive. The two options are:

Large/Auto(default:Auto)

Capacity Capacity of currently installed hard drive.
Hard drive information should be labeled on the outside drive casing. Enter the appropriate option
based on this information.

Cylinder Number of cylinders

Head Number of heads

Precomp Write precomp

Landing Zone Landing zone

Sector Number of sectors

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the
system.
The value of the base memory is typically 512 K for systems with 512 K memory installed on the
motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

The BIOS determines the total memory is present during the POST.

BIOS Version

The BIOS determines the current BIOS version.

BIOS Setup

28

3-2 Advanced BIOS Features

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.
Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press
<ESC> to exit this menu.

First / Second / Third Boot Device

Hard Disk Select your boot device priority by Hard Disk.

CDROM Select your boot device priority by CDROM.

USB-FDD Select your boot device priority by USB-FDD.

USB-ZIP Select your boot device priority by USB-ZIP.

USB-CDROM Select your boot device priority by USB-CDROM.

USB-HDD Select your boot device priority by USB-HDD.

LAN Select your boot device priority by LAN.

Disabled Disable this function.

Password Check

System The system can not boot and can not access to Setup page will be denied if the

correct password is not entered at the prompt.

Setup The system will boot, but access to Setup will be denied if the correct password

is not entered at the prompt. (Default setting)

Limit CPUID Max. to 3

Enabled Limit CPUID Maximum value to 3 when use older OS like NT4.

Disabled Disable CPUID Limit for windows XP. (Default setting)

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Advanced BIOS Features

` Hard Disk Boot Priority [Press Enter]

First Boot Device [Floppy]
Second Boot Device [Hard Disk]
Third Boot Device [CDROM]
Password Check [Setup]
Limit CPUID Max. to 3 [PCI]
Init Display First [Enabled]
On-Chip Frame Buffer Size [8MB]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help
Menu Level`

GA-6JIEV-RH Motherboard

29

Init Display First

This feature allows you to select the first initation of the monitor display from which card, when
you install a PCI VGA card or a onboard VGA device.

PCI Set Init Display First to PCI Slot. (Default setting)

Onboard Set Init Display First to onbaord VGA device.

On-Chip Frame Buffer Size

1MB Set on-chip frame buffer size to 1 MB.

8MB Set on-chip frame buffer size to 8 MB. (Default setting)

(Note) This item will show up when you install a processor which supports this function.

BIOS Setup

30

3- 3 Integrated Peripherals

On-Chip Primary PCI IDE

Enabled Enable onboard 1st channel IDE port. (Default setting)

Disabled Disable onboard 1st channel IDE port.

On-Chip SATA Mode

Disabled Disable this function.

Auto BIOS will auto detect. (Default setting)

Combined Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

the motherboard; 2 for SATA and the other for PATA.

Enhanced Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6 HDDs

to use; 4 for SATA and the other for PATA.

Non-Combined Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

PATA mode. Support a maximum of 4 SATA devices. PATA devices will be
ignored.

PATA IDE Set to

Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave. (Default setting)

Ch.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave.

SATA Port 0/2 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

USB Controller

Enabled Enable USB controller. (Default setting)

Disabled Disable USB controller.

USB 2.0 Controller

You can disable this function if you are not using onboard USB 2.0 feature.

Enabled Enable USB 2.0 controller. (Default setting)

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE [Enabled]
On-Chip SATA Mode [Auto]

x PATA IDE Set to Ch.0 Master/Slave

SATA Port 0/2 Set to Ch.2 Master/Slave

USB Controller [Enabled]
USB 2.0 Controller [Enabled]
Legacy USB storage detect [Enabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Serial Port 2 [2F8/IRQ3]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help
Menu Level`

GA-6JIEV-RH Motherboard

31

Disabled Disable USB 2.0 controller.

Legacy USB storage detect

This option allows users to decide whether to detect USB storage devices, including USB flash
drives and USB hard drives during POST.

Enabled BIOS will scan all USB storage devices. (Default setting)

Disabled Disable this function.

Onboard Serial Port 1

3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default setting)

2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.

3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.

Disabled Disable onboard Serial port 1.

Onboard Serial Port 2

3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4.

2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3. (Default setting)

3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.

Disabled Disable onboard Serial port 1.

BIOS Setup

32

3- 4 Power Management Setup

ACPI Suspend Type

S3 (STR) Set the suspend type to RAM under ACPI OS. (Default setting)

S1 (POS) Set the suspend type to Power ON Suspend under ACPI OS.

Soft-Off by PWR-BTTN

Instant-Off Press power button then Power off instantly. (Default setting)

Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed

less than 4 sec.

AC BACK Function

Soft-Off When AC-power back to the system, the system will be in "Off" state.

(Default setting)
Full-On When AC-power back to the system, the system always in "On" state.
Memory When AC-power back to the system, the system will return to the Last state

before AC-power off.

Resume by Alarm

You can set "Resume by Alarm" item to Enabled and key in Date/Time to power on system.

Disabled Disable this function. (Default value)
Enabled Enable alarm function to POWER ON system.

If Resume by Alarm is Enabled.

Date (of Month) Alarm : Everyday, 1~31
Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Power Management Setup

ACPI Suspend Type [S3(STR)]
Soft-Off by PWR-BTTN [Instant-Off]
AC Back Function [Memory]

Resume by Alarm [Disabled]

x Date (of Month) Alarm Everyday
x Time (hh:mm:ss) Alarm 0 : 0 : 0

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help
Menu Level`

GA-6JIEV-RH Motherboard

33

3- 5 PC Health Status

Current Voltage(V) Vcore / DDR18V / +3.3V / +12V / VCC15V / DDRVTT

Detect system's voltage status automatically.

Current CPU/System Temperature

Detect CPU and System temperature automatically.

Current CPU/SYSTEM FAN Speed (RPM)

Detect CPU/system fan speed status automatically.

CPU Warning Temperature

60oC / 140oF Monitor CPU temperature at 60oC / 140oF.
70oC / 158oF Monitor CPU temperature at 70oC / 158oF.
80oC / 176oF Monitor CPU temperature at 80oC / 176oF.
90oC / 194oF Monitor CPU temperature at 90oC / 194oF.
Disabled Disable this function. (Default setting)

CPU/System FAN Fail Warning

Disabled Disable the fan fail warning function. (Default setting)
Enabled Enable the fan fail warning function.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

PC Health Status

Vcore 0.992V

DDR18V 1.776V

+3.3V 3.280V

+12V 11.287V

VCC15V 1.504V

DDRVTT 0.864V

Current SYSTEM Temperature 36

o

C
Current CPU Temperature 38oC
Current CPU FAN Speed 2880 RPM
Current SYSTEM FAN Speed 0 RPM

SYSTEM Warning Temperature [Disabled]
CPU Warning Temperature [Disabled]
CPU FAN Fail Warning [Disabled]
SYSTEM FAN Fail Warning [Disabled]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help

Menu Level`

BIOS Setup

34

3- 6 Frequency/Voltage Control

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Frequency/Voltage Control

PCICLK Control [Auto]
Spread Spectrum [Enabled]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item Help

Menu Level`

PCICLK Control

Disabled Enable all PCI slot CLKs even no PCI device is plugged into any PCI slot.
Auto Disable PCI slot CLK if no PCI device is plugged into corresponding PCI slot.

(Default setting)

Spread Spectrum

Disabled Disable Spread Spectrum.
Enabled Enable Spread Spectrum. (Default setting)

(Note) This item will show up when you install a processor which supports this function.

Incorrectly using these features may result in system instability or corruption.
Doing a overclock or overvoltage on CPU, chipsets and memory modules may result in
damages or shortened life expectancy to these components.
Please be aware that the menu items are for power users only.

GA-6JIEV-RH Motherboard

35

3- 7 Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum
system performance.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Load Fail-Safe Defaults

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Load Fail-Safe Defaults (Y/N)? N

3- 8 Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automati­cally detects.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Load Optimized Defaults

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Load Optimized Defaults (Y/N)? N

GA-6JIEV-RH Motherboard

36

3- 9 Set Supervisor/User Password

When you select this function, the following message will appear at the center of the screen to assist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS
Setup program function. When enabled, the Supervisor password is required for entering the BIOS
Setup program and having full configuration fields, the User password is required to access only basic
items.
If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted
for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only
when you try to enter Setup.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Change/Set/Disable Password

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Enter Password:

BIOS Setup

37

3-10 Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.
Type "N" will return to Setup Utility.

3- 11 Exit Without Saving

Type "Y" will quit the Setup Utility without saving to RTC CMOS.
Type "N" will return to Setup Utility.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Abandon all Data

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Quit Without Saving (Y/N)? N

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Save Data to CMOS

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Save to CMOS and EXIT (Y/N)? Y

GA-6JIEV-RH Motherboard

38

3-12 Flash BIOS Method Introduction

Method 1 : Q-Flash

TM

Q-FlashTM is a BIOS update tool that allows the user to update BIOS
without entering operating systems like MS-DOS or Windows.Em­bedded in the BIOS, the Q-FlashTM tool frees you from the hassles of

going through complicated BIOS flashing process.

Before Use:

Follow the steps below before using Q-Flash to update BIOS:

1. From GIGABYTE's website, download the latest compressed BIOS update file that matches your
motherboard model.

2. Extract the downloaded BIOS files and save the new BIOS file (e.g. 6jiev.f1) to your floppy
diskor hard disk. Note: Q-Flash only supports hard disks or flash drives using FAT32/16/12 file system.

3. Restart the system. During BIOS POST, press the End key to enter Q-Flash. NOTE: Press the
Endkey to enter Q-Flash if you wish to use hard drives in RAID/AHCI mode or hard drives
attached to the independent IDE/SATA controller.

Step 1:
a. In the Q-Flash menu, use the UP or DOWN ARROW key to select Update BIOS from Drive and

press ENTER.

b. Select the floppy drive or hard drive where the BIOS file is saved, such as "Floppy A" and

press ENTER.

If you wish to back up the current BIOS file, use the Save BIOS to Drive function.

Updating the BIOS

Q-Flash Utility v2.02

Flash Type/Size.................................MXIC SPI Serial F1a 512K

Keep DMI Data Enable

Update BIOS from Drive

Save BIOS to Drive

Enter : Run KL:Move ESC:Reset F10:Power Off

0 file(s) found

Floppy A <Drive>
HDD 0-0 <Drive>

Total size : 0 Free size : 0
F5 : Refresh DEL : Delete

Because BIOS flashing is potentially risky, please do it with caution and avoid inadequate
operation that may result in system malfunction.

BIOS Setup

39

Step 2: The process of system reading the BIOS file from the floppy disk is displayed on the screen.

When the message "Are you sure to update BIOS?" appears, press ENTER. The BIOS update
will begin and the current process will be displayed.

1. Do not turn off or restart the system when the system is reading/updating the BIOS.

2. Do not remove the floppy disk or hard drive/USB drive when the system is updating the BIOS.

Step 3: When the update process is complete, press any key to return to the Q-Flash main menu.

Step 4: Press ESC and then ENTER to exit Q-Flash and the system will restart. As the system reboots,

you will see the new BIOS version during POST.

Step 5: As the system r eboots, press DELETE to enter BIOS Setup. Select Load Optimized Defaults

and press ENTER to load BIOS defaults. System will re-detect all peripherals devices after
BIOS update, so we recommend that you reload BIOS defaults.

Press Y to load BIOS defaults

Step 6: Select Save & Exit Setup and then press Y to save settings to CMOS and exit BIOS Setup.

When the system restarts, the whole update process is complete.

Q-Flash Utility v2.02

Flash Type/Size.................................MXIC SPI Serial F1a 512K

Keep DMI Data Enable

Update BIOS from Drive

Save BIOS to Drive

Enter : Run KL:Move ESC:Reset F10:Power Off

!! Copy BIOS completed - Pass !!

Please press any key to continue

c . Select the BIOS file and press ENTER.

Make sure again the BIOS file matches your motherboard model.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features
` Advanced BIOS Features
` Integrated Peripherals
` Power Management Setup
` PnP/PCI Configurations
` PC Health Status
` Frequency/Voltage Control

ESC: Quit KLJI: Select Item
F8: Q-Flash F10: Save & Exit Setup

Load Optimized Defaults

Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving

Load Optimized Defaults (Y/N)? Y

GA-6JIEV-RH Motherboard

40