Page 1
AV64S-T
RADEONTM 7000E Graphics Accelerator
REV. 1.32
12MD-AV64ST-132
USER'S MANUAL
中文使用手冊
Upgrade your Life
Page 2
2
AV64S-T Graphics Acceler ator
Copyright
Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. (“GBT”) No part of this manual
may be reproduced or transmitted in any from without the expressed, written permission of
GBT.
Trademarks
Third-party brands and names are the property of their respective owners.
Notice
Due to rapid change in technology, some of the specifications might be out of date before
publication of this booklet.
The author assumes no responsibility for any errors or omissions which may appear in this
document nor does it make a commitment to update the information contained herein.
Please do not remove any labels on VGA card , this may void the warranty of this VGA
card.
March 17, 2003 Taipei, Taiwan
Chapter 1 User’s Manual
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by M acrovision Corporation. Reverse engineer-
ing or disassembly is prohibited.
Page 3
3
Table of Content
Table of Contents
1.INTRODUCTION
1.1. PREFACE ................................................................................... 4
1.2. Overview ....................................................................................4
2.HARDWARE INSTALLATION
2.1. UNPACKING ............................................................................... 5
2.2. BOARD LAYOUT .........................................................................6
2.3. HARDWARE INSTALLATION .......................................................7
3.SOFTWARE INSTALLATION
3.1Win98 /98SE or WinME /Win XP Driver And Utilities Installation ..........9
3.1.1 Operating system requirement ..................................................9
3.1.2 DirectX installation .................................................................. 10
3.1.3 Driver installation ................................................................... 12
3.1.4 Utilities on driver CD ..............................................................15
3.1.5 Taskbar Icon ......................................................................... 15
3.1.6 Property pages ..................................................................... 18
3.2.WINDOWS NT 4.0 DRIVER INSTALLATION .............................. 23
3.3.WINDOWS 2000 DRIVER INSTALLATION ................................... 24
3.4 BIOS FLASH UTILITY ................................................................ 24
4.Troubleshooting Tips ................................................................................. 25
5.Appendix
5.1.How to refash the BIOS ............................................................... 26
5.2.Resolutions and Color Depth Table .............................................. 28
Page 4
4
AV64S-T Graphics Acceler ator
1.INTRODUCTION
1.1. PREFACE
AV Series delivers enhanced 3D and 2D graphics performance for today’s demanding applications.
Powered by the ATi RADEON™ 7000E graphics processor and 32 / 64 MB SDR memory; Maya AV
Series features HYPER Z™ technology to increase effective memory bandwidth and PIXEL TAPESTRY™ for fast image rendering. AV Series has industry leading, built-in DVD playback capability..
1.2. KEY FEATURES
n Powered by the RADEON™ 7000E graphics processor
n ATI HYPER Z™ technology reduces memory bandwidth consumption
resulting in improved 3D performance
n Incredible 3D graphics performance with ATI PIXEL TAPESTRY™ 3D
rendering engine
n Supports DirectX® 7.0, DirectX® 8.x and OpenGL
®
n DVD playback with integrated motion compensation and iDCT
n Supports 3D resolutions (32-bit color) up to 2048x1536
n AGP universal bus (for AGP 2X/4X systems)
n Support TV-OUT
Chapter
1
User's Manual
Page 5
5
Hardware Installation
2.HARDWARE INSTALLATION
WARNING!
Expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against
damage from static electricity, you should follow some precautions whenever you work on your
computer.
1.Turn off your computer and unplug power supply.
2.Use a grounded wrist strap before handling computer components. If you do not have one, touch
both of your hands to a safely grounded object or to a metal object, such as the power supply
case.
3.Place components on a grounded antistatic pad or on the bag that came with the components
whenever the components are separated from the system.
The card contains sensitive electric components, which can be easily damaged by static electricity
, so the card should be left in its original packing until it is installed.
Unpacking and installation should be done on a grounded anti-static mat. The operator should be
wearing an anti-static wristband, grounded at the same point as the anti-static mat.
Inspect the card carton for obvious damage. Shipping and handling may cause damage to your
card. Be sure there are no shipping and handling damages on the card before proceeding.
M DO NOT APPLY POWER TO YOUR SYSTEM IF IT HAS BEEN DAMAGED ON THE
CARD.
MIn order to ensure your graphics card working correctly, please use official Gigabyte
BIOS only Use none official gigabyte BIOS might cause problem on the graphics card.
2.1. UNPACKING
The AV64S-T package contains the following:
l The AV64S-T graphics accelerator
l This USER'S MANUAL
l DVD Player software included
l Full version Game x1 (CD x 1)
l Lite version Game x2 (CD x 1)
l CD for driver & Utilities
Page 6
6
AV64S-T Graphics Acceler ator
2.2. BOARD LAYOUT
AV64S-T (8Mx16 64MB SDRAM)
8Mx16 Frame Buffer SDRAM
BIOS
ATi
RADEON 7000E
S-Vid eo
(TV-Ou t)
VGA M onitor
C onne cto r
(1 5pi n)
Co mpos ite RC A Output
S-V ideo Output
VGA Output
Co mposite RCA
C onne cto r
(TV-OU T)
S-Vid eo
(TV-Ou t)
VGA M onitor
C onne cto r
(1 5pi n)
Co mposite RCA
C onne cto r
(TV-OU T)
Page 7
7
Hardware Installation
2.3. HARDWARE INSTALLATION
Installing Your Graphics card..
Now that you have prepared your computer, you are ready to install your graphics
accelerator card.
To install your graphics accelerator card
1. Power off the computer and monitor , then disconnect the display cable from the
backof your computer.
2. Remove the computer cover. If necessary, consult your computer's manual for help
in removing the cover.
3. Remove any existing graphics card from your computer.
Or, if your computer has any on-board graphics capability, you may need to disable it ...
on the motherboard. For more information, see your computer documentation.
Page 8
8
AV64S-T Graphics Acceler ator
4. Locate the AGP slot. If necessary, remove the metal cover from this slot; then align
your Graphics card with the AGP slot, and press it in firmly until the card is fully
eated.
5. Replace the screw to fasten the card in place, and replace the computer cover.
6. Plug the display cable into your card; then turn on the computer and monitor.
You are now ready to proceed with the installation of the Graphics card driver. For detailed
instructions, select your operating system from the list below:
AV64S- T Graphics card
AGP Slot
AV64S- T Graphics card
To VGA MONI TOR
S-Vid eo
(TV-Ou t)
Co mposite RCA
C onne cto r
(TV-OU T)
Page 9
9
Software Installation
3.SOFTWARE INSTALLATION
In this manual, we assume that your CD-ROM Drive letter to be Drive D:
3.1. WINDOWS®98 /98SE or WINDOWS ME /WINDOWS XP DRIVER
AND UTILITIES INSTALLATION
The installation of Win 98/98SE / Win ME / Win XP drivers is very simple.
When you insert the driver CD into your CD-ROM drive, you can see the AUTORUN
window (if it does not show up, run "D:\setup.exe"). Then you can follow guides to setup
your AV64S-T driver (Please follow the subsection 3.1.3 "Step By Step Installation" to
install the driver for your graphics accelerator.
3.1.1.Operating system requirement
l If your OS is Microsoft Windows, when loading the AV64S-T drivers for the
system, please make sure your system ( Windows 98/98SE or Windows ME)has
installed DirectX8.1 or later.
l If you install the AV64S-T drivers for the mainboard, which
consist of SIS, ALI or VIA chipsets, please install the appropriate Driver program for
that mainboard. Or please contact your motherboard nearest dealer for M/B Diver.
Page 10
10
AV64S-T Graphics Acceler ator
3.1.2.DirectX Installation
Install Microsoft DirectX 8.1 to enable 3D hardware acceleration support for Win98/98SE or
WinME to achieve better 3D performence.
Note: For software MPEG support in Win98/98SE or WinME, you must DirectX first install.
2.Click "Yes" icon.
3.Click "Yes“ icon.
1. Installation DirectX Driver
Click "Display Driver Setup Utility” Item.
Page 11
11
Software Installation
4.Click "OK" item.
Page 12
12
AV64S-T Graphics Acceler ator
3.1.3.Driver Installation
The following is the step-by-step installation guide.
Step 1: New Hardware Found
After AV64S-T is inserted into your computer at the first time, the windows will automatically
detect a new hardware in the system and pop out a "New Hardware Found" message.
Please select "Do not install a driver" and press OK.
Step 2: Update Device Driver Wizard: Standard PCI Graphics Adapter(VGA)
Step 3: Update Device Driver Wizard: Finish
At this time, system will ask for your Windows CD in order to complete the VGA driver
installation.
If you don't have the CD, you can press C:\Windows\System directory.
Step 4: System Setting Change
1.Click "Next“ icon.
2..Click "Finish“ icon.
MDon’t click “Cancel”, because
the system will hang if you press it.
Page 13
13
Software Installation
After the system has finished loading, insert the AV64S-T driver CD disk into your CDROM, and then you can see the AUTORUN window. If it does not show up, please run
"D:\setup.exe".
3..Click "NO“ icon.
Step 5: Driver Setup
1. Click "Install Display Driver(Radeon
VE Series)
Page 14
14
AV64S-T Graphics Acceler ator
2..Click “Next“ icon.
3.Click “Yes” icon.
4.Click “Finish” icon to restart
computer.
Page 15
15
Software Installation
3.1.5 Taskbar Icon
3.1.4.Utilities on driver CD
The utilities include Display Driver and V-Tuner utilities. Please browse the driver CD for
detail.
After installation of the display drivers, you will find an GBT icon on the taskbar’s status
area. Right-clicking this icon opens the GBT control panel, showing a menu composed of
shortcute of the graphics board’s enhanced and other functions.
You may click the “Display Properties” item, and then click Settings. Click “Advanced” after
clickng Settings. Click the appropriate tab to change your display settings.
You can link to GBT web site
for updated information about
the graphics borad, latest
drivers, and other information.
Page 16
16
AV64S-T Graphics Acceler ator
V-Tuner (Overclock Utility)
V-Tuner lets you adjust the working frequency of the graphic engine and
video memory (Core Clock and Memory Clock)
Page 17
17
Software Installation
VGA Info
VGA Info lists the relevant information about your card.
Color Adjust
Color Adjust allows you to make color adjustments, such as brightness,
contrast, and gamma values for each or all of RGB colors.
Page 18
18
AV64S-T Graphics Acceler ator
3.1.6.Display Property pages
The screen shows the information of display adapter, color, the range of display area..
and the refresh rate.
Setting (Resolutions and Color depth for windows)
The Setting properties page allows you to adjust the Direct 3D settings
Options Properties
Click” Advanced..”icon for adapter
and setting.
You can click the item to change the
color depth.
You can move the slider to the
change resolution.
n Enable ATI taskbar icon application enables or
disables the ATI taskbar icon. However, this feature
must be enabled for ATI hotkey support.
n Show ATI icon on taskbar adds or removes the ATI
icon from the taskbar.
Page 19
19
Software Installation
OpenGL Properties:
The OpenGL properties page gives you complete control of the OpenGL settings.
n Optimization Preference
l Quality allows you to optimize your OpenGL settings for quality.
l Performance allows you to optimize your OpenGL settings for performance
n OpenGL Settings
l Convert 32 bit textures to 16 bit allows you to increase video performance for games
that make heavy use of textures. However this could also reduce image quality.
l Enable KTX buffer region extension enables rapid updates of those portions of your
screen that have been moved.
l Enable page flipping allows you to enable hardware acceleration of page flipping to
swap full screen buffers.
l Force 16-bit Z-buffering allows you to disable all other formats of Z-buffer and utilizes
16-bit Z-buffering.
l Disable dithering when alpha blending may remove artifacts left on the screen
when both dithering and alpha blending are enabled.
l Wait for vertical sync lowers the frames per second rate in full screen games
However this can reduce the image tearing that can occur with higher frame rates.
l Enable texture compression enables and disables texture compression.
l Full Screen anti-aliasing allows you to set the level of full-screen anti-aliasing. This
will result in an overall higher quality image with a slight reduction in performance.
Page 20
20
AV64S-T Graphics Acceler ator
Direct 3D Display Properties
The Direct 3D properties page allows you to adjust the Direct 3D settings.
D3D Settings
n Wait for vertical sync allows you to lower the frame rate of full screen games. This will
reduce image tearing that can occur with higher frame rates.
n W-buffer support allows you to enable or disable W-buffer support. It is recommend that W-
buffer support should be disabled for games that do not support this feature.
n Compressed texture format allows you to enable support for DirectX compressed texture
formats. Some applications cannot handle too many texture formats. Disabling compressed
texture format the video driver ceases to support this feature.
n Alternate pixel center may eliminate problems with some 3D games that displays vertical .
and horizontal lines around textures or text that appears incorrect. However, this setting
should only be used if you are experiencing these symptoms, as it may cause problems
with other games.
n Z-buffer bit depths allows you to set the Z-buffer bit rate. By default 16:24 (16 and 24) is
selected to achieve optimum performance.
8-bit Stencil allows you to add 32-bit Z-buffer with 8 bits for stencil and 24 bits for the Z-buffer.
l Anisotropic texture filtering allows you to set a level of anisotropic texture filtering.
This will result in much higher quality textures with a negligible reduction in performance.
l Level of Detail allows you to set the level of mipmapped detail.
The Sharp setting is recommended for larger, more detailed, mipmapping scenes. The
Fuzzy setting is recommended for smaller, less detailed, mipmapping scenes.
Page 21
21
Software Installation
n Anti-aliasing provides you with an overall higher quality video image with a slight reduction
in performance. When “Application Preference” mode is selected, the video driver will use
anti-aliasing only when an application requests it. When “Always On” mode is selected, the
video driver will force anti-aliasing on all applications.
n 2 Samples provides a higher sample ratio, which improves overall image quality even
further, with a slight reduction in performance. This also requires more video memory.
4 Sample provides a higher sample ratio, which improves overall image quality even further,
with a slight reduction in performance. This also requires more video memory.
n Dithering method when alpha blending will remove certain onscreen artifacts that are
sometimes produced when both dithering and alpha blending are enabled.
n Defaults restores your Direct 3D setting to their default values.
Color Properties
The Color Properties is used to adjust the color settings. It also allows gamma control for video
playing of the Video Overlay. The color settings affect all display devices mapped to the view.
You can change red, green, and blue display colors. Set Desktop and Video Overlay brightness
(gamma) levels can also be changed.
n Desktop brightness increases or decreases the
color brightness of you desktop. The higher the
gamma value, the higher the brightness and
contrast of your display.
n Overlay brightness increases or decreases the
color brightness of your video overlay window. The
higher the gamma value, the higher the brightness
and contrast of your display.
n Game gamma increases or decreases the color
brightness of Direct 3D or OpenGL games
played in fullscreen mode.
n Color Curve adjusts the selected color (red, green,
or blue) by moving the color curve with
your mouse.
n Default restores the color settings to the default
values.
Page 22
22
AV64S-T Graphics Acceler ator
Display Properties:
If you VGA card is equipped with a S-Video connector , you can use a second output device (e.q. a
TV or a computer monitor) as part of your operating desktop extending your desktop to second device
or copying your desktop on the second device.
Connecting your graphics card to a TV or VCR
Turn off your computer and your television (or VCR).
Ensure your graphics card is installed correctly.
For information about placing the card in your computer and installing the enhanced graphics driver,
see the user’s manual.
Determine if your television (or VCR) has an S-Video or Composite video connection.
Looking at the back of your computer, locate your graphics card. Using an S-Video cable or the
supplied adapter cable, attach one end of the cable to your graphics card and the other to your
television (or VCR). See “Connecting your graphics card to a TV (or VCR)” on the following page.
Select Display Type
Enable /Disable”Extend my windows
desktop onto this monitor
Page 23
23
Software Installation
3.2. WINDOWS NT 4.0 DRIVER INSTALLATION
Please make sure the Windows NT4 have installed Windows NT 4.0 Service Pack version
6.0 (or later) before installing the graphics accelerator driver.
To install the AV64S-T driver for Windows NT
1. Insert the INSTALLATION CD into your CD-ROM drive. If Windows ® runs the CD
automatically.
2. Click Start.
3. Select Run.
4. Type the following:
D:\SETUP
(If D is not your CD-ROM drive, substitute D with the correct drive letter.)
5. Click “OK”.
6. Click on “Install Display Drivers(Radeon VE Series)” to begin the Installation
Wizard.
7. Click “Next”.
8. Click” Yes” to the license agreement.
9. Follow the Wizard's on-screen instructions to complete the installation.
Page 24
24
AV64S-T Graphics Acceler ator
3.3.WINDOWS 2000 DRIVER INSTALLATION
Please make sure the Windows NT 2000 have installed Windows ® 2000 Service Pack
version 2 (or later) before installing the graphics accelerator driver.
With Windows
®
2000 running on your computer, you need to install the AV64S-T driver to
take advantage of the higher performance, resolutions, and special graphic features of the
Graphics card. To ensure you install the latest driver, use the Installation CD that shipped
with your Graphics card.
To install the AV64S-T driver for Windows ® 2000
1. Insert the INSTALLATION CD into your CD-ROM drive. If Windows® runs the CD
automatically.
2. Click Start.
3. Select Run.
4. Type the following:
D:\SETUP
(If D is not your CD-ROM drive, substitute D with the correct drive letter.)
5. Click “OK”.
6. Click on “Install Display Drivers(Radeon VE Series)” to begin the Installation
Wizard.
7. Click “Next”.
8. Click “Yes” to the license agreement.
9. Follow the Wizard's on-screen instructions to complete the installation.
3.4.BIOS FLASH UTILITY
AV64S-T BIOS update procedure:
MNote: Please download the newest BIOS from our website (www.gigabyte.com.tw)
or contact your local dealer for the file.
MIf you want to realize the BIOS flash information, please refer to detail on P.26
Page 25
25
Troubleshooting Tips
4.Troubleshooting Tips
The following troubleshooting tips may help if you experience problems. Contact your
dealer or GBT for more advanced troubleshooting information.
n Check that the card is seated properly in the AGP slot.
n Ensure the display cable is securely fastened to the card's display connector.
n Make sure that the monitor and computer are plugged in and receiving power.
n If necessary, disable any built-in graphics capabilities on your motherboard. For
more information, consult your computer's manual or manufacturer. (NOTE: Some
manufacturers do not allow the built-in graphics to be disabled or to become the
secondary display.)
n Make sure you selected the appropriate display device and graphics card when
you installed the graphics driver.
n For more troubleshooting tips, right-click the ATI icon in the taskbar and select
Troubleshooting.
n If you have problems during bootup, start your computer in Safe Mode. In
Windows®98 SE and Windows ® Me, press and hold the CTRL key until the
Microsoft ® Windows ® Startup Menu appears on the screen. Then select the
number for Safe Mode, and press Enter. (You can also use F8 to bring up the
Microsoft Windows ®Startup Menu.) In Safe Mode, bring up the Device Manager
and check for duplicate display adapter and monitor entries if you are only using
one graphics card.
n For more assistance, use the Troubleshooting Guide located in the Windows
®
Help or contact your computer manufacturer.
Page 26
26
AV64S-T Graphics Acceler ator
5.Appendix
5.1. How to reflash the BIOS
How to reflash the BIOS for your graphics card?
1. Extract the Zip file to the drive C: or A:
2. Restart your PC in MS-DOS mode
(This function only for Windows 98/98SE, If your OS is Windows 2000 /
Windows Me / Windows XP. please use the bootable disk to MS-DOS mode)
Page 27
27
Append ix
3. Change the command path to the file location C:\> or A:\>
4. Reflash BIOS command as below : C:\> atiflash -p 0 <filename>
5. Reboot your PC when it's done.
Page 28
28
AV64S-T Graphics Acceler ator
5.2.Resolutions and Color Depth Table
Displ ay Refresh Hor. Pix el Color Depth (bpp)
Screen Rate Scan Clo ck 8bpp(256 color) 16bpp(65K color) 32bpp(16.7M)
Resolution (Hz) (KHz) (Mhz) Standard mode High mode True mode
60 31.5 25.2 P P P
72 37.9 31.5 P P P
75 37.5 31.5 P P P
640x480 85 43.3 36.0 P P P
90 45.4 37.8 P P P
100 50.9 43.1 P P P
120 61.8 52.4 P P P
160 84.3 72.8 P P P
200 108.0 95.0 P P P
60 37.9 39.9 P P P
70 43.7 45.5 P P P
72 48.1 50.0 P P P
800x600 75 46.9 49.5 P P P
85 53.7 56.3 P P P
90 56.8 60.0 P P P
100 63.6 68.1 P P P
120 77.1 83.9 P P P
160 105.4 116.4 P P P
200 135.0 149.0 P P P
60 48.4 65.0 P P P
70 56.5 75.0 P P P
72 57.6 78.4 P P P
1024x768 75 60.0 78.8 P P P
85 68.7 94.5 P P P
90 72.8 100.1 P P P
100 81.4 113.3 P P P
120 98.7 139.0 P P P
140 116.6 164.2 P P P
To be continued..
RADEON 7000E 2D Display Modes
Page 29
29
Append ix
DDispl ay Refresh Hor. Pix el Color Depth (bpp)
Screen Rate Scan Clo ck 8bpp(256 color) 16bpp(65K color) 32bpp(16.7M)
Resolution (Hz) (KHz) (Mhz) Standard mode High mode True mode
150 125.7 176.9 P P P
1024x768 160 134.8 192.0 P P P
200 172.8 246.1 P P P
43 38.0 56.0 P P P
47 41.7 62.1 P P P
60 53.7 81.6 P P P
70 63.0 96.7 P P P
75 67.5 108.0 P P P
1152x864 80 72.4 112.3 P P P
85 77.0 119.6 P P P
100 91.5 143.4 P P P
120 111.1 176.0 P P P
150 141.4 226.3 P P P
160 151.6 242.6 P P P
60 64.0 108.0 P P P
70 74.6 128.9 P P P
74 79.0 138.5 P P P
1280x1024 75 80.0 135.0 P P P
85 91.1 157.5 P P P
90 97.0 169.2 P P P
100 108.5 190.9 P P P
120 131.6 233.7 P P P
52 64.2 137.7 P P P
58 71.9 155.4 P P P
1600x1200 60 75.0 162.0 P P P
66 82.2 178.9 P P P
75 93.8 202.5 P P P
76 95.2 208.7 P P P
85 106.3 229.5 P P P
92 116.4 257.0 P P P
100 127.1 280.6 P P P
To be continued..
Page 30
30
AV64S-T Graphics Acceler ator
DDispl ay Refresh Hor. Pix el Color Depth (bpp)
Screen Rate Scan Clo ck 8bpp(256 color) 16bpp(65K color) 32bpp(16.7M)
Resolution (Hz) (KHz) (Mhz) Standard mode High mode True mode
1792x1344 60 83.5 203.0 P P P
75 105.2 259.3 P P
85 119.9 295.5 P P P
1800x1440 60 89.4 219.5 P P P
1920x1080 60 67.0 172.7 P P P
70 78.6 205.1 P P P
75 84.6 220.6 P P P
80 90.4 237.4 P P P
60 74.5 193.1 P P P
72 90.0 222.2 P P P
1920x1200 75 93.9 231.4 P P P
80 100.5 263.7 P P P
85 107.1 282.7 P P P
1920x1440 60 89.4 234.5 P P P
75 112.7 297.6 P P P
2048x1536 60 95.3 267.0 P P P
Loading...