6ZMA/6ZM
1
TABLE OF CONTENTS
1. INTRODUCTION
1.1. PREFACE..........................................................................................................1-1
1.2. KEY FEATURES...............................................................................................1-1
1.3. PERFORMANCE LIST......................................................................................1-2
1.4. BLOCK DIAGRAM.............................................................................................1-3
1.5. INTRODUCE THE Pentium II / III Processor ................................................1-4
1.6. What is AGP?....................................................................................................1-5
2. SPECIFICATION
2.1. HARDWARE .....................................................................................................2-1
2.2. SOFTWARE......................................................................................................2-2
2.3. ENVIRONMENT................................................................................................2-2
3. HARDWARE INSTALLATION
3.1. UNPACKING.....................................................................................................3-1
3.2. MAINBOARD LAYOUT.....................................................................................3-2
3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS..............................3-3
3.4. DRAM INSTALLATION.....................................................................................3-7
3.5. CPU SPEED SETUP.........................................................................................3-8
3.6. CMOS RTC & ISA CFG CMOS SRAM.............................................................3-9
3.7. SPEAKER CONNECTOR INSTALLATION......................................................3-10
3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION....................3-10
3.9. POWER LED CONNECTOR INSTALLATION.................................................3-10
Table Of Contents
2
3.10. IDE & ATAPI DEVICE INSTALLATION..........................................................3-10
3.11. PERIPHERAL DEVICE INSTALLATION........................................................3-10
3.12. KEYBOARD & PS/2 MOUSE INSTALLATION...............................................3-11
4. BIOS CONFIGURATION
4.1. ENTERING SETUP...........................................................................................4-1
4.2. CONTROL KEYS ..............................................................................................4-1
4.3. GETTING HELP................................................................................................4-2
4.3.1Main Menu............................................................................................4-2
4.3. 2 Status Page Setup Menu / Option Page Setup Menu .........................4-2
4.4. THE MAIN MENU.............................................................................................4-2
4.5. STANDARD CMOS SETUP MENU..................................................................4-4
4.6. BIOS FEATURES SETUP ................................................................................4-8
4.7. CHIPSET FEATURES SETUP.........................................................................4-12
4.8. POWER MANAGEMENT SETUP....................................................................4-16
4.9. PNP/PCI CONFIGURATION ............................................................................4-20
4.10. LOAD BIOS DEFAULTS.................................................................................4-22
4.11. LOAD PERFORMANCE DEFAULTS .............................................................4-23
4.12. INTEGRATED PERIPHERALS.......................................................................4-24
4.13. SUPERVISOR/USER PASSWORD...............................................................4-29
4.14. IDE HDD AUTO DETECTION........................................................................4-30
4.15. SAVE & EXIT SETUP .....................................................................................4-31
4.16. EXIT WITHOUT SAVING ...............................................................................4-32
APPENDIX A: Audio Driver Driver Installation
6ZMA/6ZM
3
A.1. ESS Solo-1 PCI sound driver installation...........................................................A-1
6ZMA/6ZM
1-1
1. INTRODUCTION
1.1. PREFACE
Welcome to use the 6ZMA/6ZM motherboard. It is a Pentium II / III /
Celeron Processor based PC / AT compatible system with AGP/ PCI / ISA
Bus, and has been designed to be the fastest PC / AT system. There are
some new features allow you to operate the system with just the
performance you want.
This manual also explains how to install the motherboard for operation, and
how to set up your CMOS CONFIGURATION with BIOS SETUP program.
1.2. KEY FEATURES
q Intel Pentium
II / III / Celeron Processor based PC / AT compatible
mainboard.
q Slot 1 supports Pentium
II / III / Celeron processor running at 233-650
MHz.
q Intel 440ZX chipset, Supports SDRAM / Ultra DMA/33 IDE.
q Built-in PCI ESS SOLO-1 audio chip.(Optional)
q Supports external Modem Ring-On on COMA & COMB and internal
Modem Ring-On.
q Supports Wake-up on LAN (JP7).
q Supports 2xDIMMs using 3.3V SDRAM DIMM module.
q Supports 16MB - 256MB SDRAM memory on board.
q 3xPCI Bus slots, 1xISA Bus slots, 1xAGP slot.
q Supports 2 channels Ultra DMA/33 IDE ports for 4 IDE Devices.
q Supports 2xCOM (16550), 1xLPT (EPP / ECP), 1x Floppy port.
q Supports1xLine in, 1xLine Out, 1xMicro in, 2xCD Line in(For PCB
Ver:1.0) (Support 1x CD Line in for PCB version 1.2 and above) ,1x
GAME Port.
(Optional)
q Supports 2xUSB ports, 1xPS/2 Mouse, 1xPS/2 Keyboard.
Introduction
1-2
q Licensed AWARD BIOS, 2Mbits FLASH RAM.
q 24.5 cm x 20 cm Micro-ATX form factor, 4 layers PCB.
1.3. PERFORMANCE LIST
The following performance data list is the testing results of some popular
benchmark testing programs.
These data are just referred by users, and there is no responsibility for
different testing data values gotten by users. (The different Hardware &
Software configuration will result in different benchmark testing results.)
• CPU
Intel Pentium II / III processor
• DRAM (128 x 1) MB SDRAM (SEC KM48S8030BT-GH)
• CACHE SIZE 512 KB included in CPU
• DISPLAY GA-630 voodoo banshee (16MB SGRAM)
• STORAGE Onboard IDE (IBM DHEA 36481)
• O.S. Windows NT™ 4.0 SPK4
• DRIVER Display Driver at 1024 x 768 x 264k colors x 75Hz.
TRIONES Bus Master IDE Driver 3.60
Intel Pentium II / III
Processor
350MHz(100x3.5) 500MHz(100x5.0)
Winbench99
CPU mark32 909 1270
FPU Winmark 1810 2560
Business Disk 4040 4230
Hi-End Disk 8200 8280
Business Graphics 155 203
Hi-End Graphics 285 397
Winstone99
6ZMA/6ZM
1-3
3.3V EDO/SDRAM
DIMM Sockets
Floppy Port
Business 27.8 33.6
Hi-End 24.1 29.8
1.4. BLOCK DIAGRAM
PS/2 Keyboard
24MHz
33MHz
33MHz
33MHz
100MHz
Ultra DMA/33
IDE Ports
IDE Bus
PCI Bus
ISA Bus
AGP Bus
LPT Port
COM Ports
DRAM Bus
PS/2 Mouse
USB Bus
USB Ports
14.318MHz
48MHz
14.318MHz
I/O
CHIPSET
Winbond
83977EF
Host Bus
PAC
82443ZX
CHIPSET
PIIX4
82371EB
CHIPSET
Clock
Generator
MIC
L-IN
L-OUT
SOLO1
33MHz
14.318MHz
66MHz
Game
Port
100MHz
AGP SLOT
TEL
Introduction
1-4
1.5. INTRODUCE THE Pentium II / III Processor
Figure 1:Universal Retention Mechanism & attach Mount
Figure 2:OEM Pentium II Processor
6ZMA/6ZM
1-5
Figure 3: OEM Pentium III Processor
1.6 What is AGP
?
The Accelerated Graphics Port (AGP) is a new port on the Host-To-PCI
bridge device that supports an AGP port. The main purpose of the AGP port
is to provide fast access to system memory.
The AGP port can be used either as fast PCI port (32-bits at 66MHz vs. 32bits at 33MHz) or as an AGP port which supports 2x data-rate, a read queue,
and side band addressing. When the 2x-data rate is used, the port can
transmit data at 533MB/sec (66.6*2*4). The read-queue can be used to
pipeline reads – removing the effects of the reads-latency. Side band
addressing can be used to transmit the data address on a separate line in
order to speed up the transaction.
Specification
2-1
2. SPECIFICATION
2.1. HARDWARE
• CPU
− Pentium
II / III / Celeron 233 – 650MHz.
− 242 pins 66/100 MHz slot1 on board.
• SPEED
− 66/100 MHz system speed.
− 66 MHz AGP bus speed. (2X mode 133MHz)
− 33 MHz PCI-Bus speed.
− 8 MHz AT bus speed.
• DRAM MEMORY
− 2 banks 168 pins DIMM module sockets on board.
− Use 16 / 32 / 64 / 128 / 256 MB DIMM module
DRAM.
− 16 ~ 256MB SDRAM.
− Supports 3.3V SDRAM.
• CACHE MEMORY
− 32 KB 1st cache memory included in CPU.
− 128KB/512KB 2nd cache in CPU.
− Supports DIB speed mode for L2 Cache.
• I/O BUS SLOTS
− 3 33MHz Master / Slave PCI-BUS.
− 1 8MHz 16 bits ISA BUS.
− 1 66MHz / 133MHz AGP bus.
• IDE PORTS
− 2 Ultra DMA 33 Bus Master IDE channels on
board.(Using IRQ14,15)
− Support Mode 3,4 IDE & ATAPI CD – ROM.
• I/O PORTS
− Supports 2 16550 COM ports.
− Supports 1 LPT port.
− Supports 1 Floppy port.
− Supports 2 USB ports.
− Supports 1 PS/2 Mouse.
− Supports 1 PS/2 Keyboard.
6ZMA/6ZM
2-2
• Audio Ports
(Optional)
− 1x Line in
− 1x Line out
− 1x Micro in
− 1x Game Port
− 2x CD Line in (For PCB Ver :1.0)
1x CD Line in (For PCB version 1.2 and above)
• GREEN FUNCTION
− Suspend mode support.
− Green switch & Green LED support.
− IDE & Display power down support.
− Monitor all IRQ / DMA / Display / I/O events.
• BIOS
− 2M bits FLASH RAM.
− Supports Plug & Play, DMI Function.
• DIMENSION
− Micro ATX Form Factor, 4 layers PCB.
2.2. SOFTWARE
• DRIVER − IUCD CD Driver.
• BIOS − Licensed AWARD BIOS.
− AT CMOS Setup, BIOS / Chipset Setup, Green
Setup, Hard Disk Utility included.
• O.S.
− Operation with MS-DOS
, Windows95,
Windows98, WINDOWS NT, OS/2, NOVELL
and SCO UNIX.
2.3. ENVIRONMENT
• Ambient Temp.
− 0°C to +50°C (Operating).
• Relative Hum. − 0 to +85% (Operating).
• Altitude − 0 to 10,000 feet (Operating).
• Vibration − 0 to 1,000 Hz.
• Electricity − 4.9 V to 5.2 V. (Max. 20A current at 5V.)
Hardware Installation
3-1
3. HARDWARE INSTALLATION
3.1. UNPACKING
The mainboard package should contain the following:
• The 6ZMA/6ZM mainboard.
• Universal Retention Mechanism & Attach Mount
• USER'S MANUAL for mainboard.
• Cable set for IDE, Floppy devices.
• CD or diskette for Mainboard ¡BSound Utility.
The mainboard contains sensitive electric components, which can be easily
damaged by static electricity, so the mainboard should be left in its original
packing until it is installed.
Unpacking and installation should be done on a grounded anti-static mat.
The operator should be wearing an anti static wristband, grounded at the
same point as the anti-static mat.
Inspect the mainboard carton for obvious damage. Shipping and handling
may cause damage to your board. Be sure there are no shipping and
handling damages on the board before proceeding.
After opening the mainboard carton, extract the system board and place it
only on a grounded anti-static surface component side up. Again inspect the
board for damage. Press down on all of the socket IC's to make sure that
they are properly seated. Do this only on with the board placed on a firm flat
surface.
M
DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED.
6ZMA/6ZM
3-2
3.2. MAINBOARD LAYOUT
PCB Ver : 1.0
SOLO 1
INTEL
443ZX
PIIX4
BIOS
JP10
JP7
TEL
CN6
JP5
GAME&AUDIO
COMB
COMA
LPT
USB
JP1
J3
SLOT 1
BAT1
SW2
JP11
J11
JP13
JP15
LED1
SW1
JP6
JP14
BZ1
J14
IR
BANK 0
BANK 1
PCI1
PCI2
PCI3
ISA
ATX POWER
FLOPPYIDE1
IDE2
6ZMA/6ZM
×
Figure 3.1
Ø
PCB Ver : 1.2
SOLO 1
INTEL
443ZX
PIIX4
BIOS
JP10
JP7
TEL
JP5
GAME&AUDIO
COMB
COMA
LPT
USB
JP1
J3
SLOT 1
BAT1
SW2
JP11
J11
JP13
JP15
LED1
SW1
JP6
JP14
BZ1
J14
IR
BANK 0
BANK 1
PCI1
PCI2
PCI3
ISA
ATX POWER
FLOPPYIDE1
IDE2
JP21
6ZMA/6ZM
×Figure 3.2Ø
Hardware Installation
3-3
3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS
t I/O Ports Connector
USB USB port.
IDE1 For Primary IDE port.
IDE2 For Secondary IDE port.
FLOPPY For Floppy port
PS/2 For PS/2 Keyboard / Mouse port.
COMB For Serial port2 (COM B).[Support External Modem Ring
On.]
COMA For Serial port1 (COM A).[Support External Modem Ring
On.]
LPT For LPT port.
GAME For GAME port.(Optional)
AUDIO For MIC,LINE-IN,LINE-OUT port.(Optional)
t Slot 1
For Pentium II / III / Celeron processor installed
t J3 : CPU FAN : CPU cooling FAN Power Connector
Pin Function
1 GND.
2 +12V
3 Signal
t J13 : Power FAN :Power FAN Power Connector
Pin Function
1 GND.
2 +12V
3 Signal
t J14 : System FAN : System FAN Power Connector
Pin Function
1 GND.
2 +12V
3 Signal
t JP7 : Wake on Lan
Pin Function
1 +5V SB
2 GND
6ZMA/6ZM
3-4
3 Signal
t IR : INFRARED Connector (IR) --(Optional)
Pin Function
1 IR Data Output
2 GND
3 IR Data Input
4 Signal
5 POWER (+)
t JP18 : Onboard Sound Function Selection (Optional)
Pin Function
1-2 Close Onboard Sound Function Enabled(Default).
2-3 Close Onboard Sound Function Disabled.
t JP1 : Keyboard Power On Selection
Pin Function
1-2 Close Enabled Keyboard power on.
2-3 Close Disabled Keyboard power on (Default).
t JP14: CLEAR CMOS Function
Pin Function
1-2 Close Clear CMOS
2-3 Close Normal operation (Default).
t JP13: Suspend To RAM Function (Optional).
Pin Function
OPEN Normal operation(Default).
Close Enabled Suspend To RAM.
t JP11: System Acceleration
Pin Function
1-2 short For 100MHz Turbo and other frequencies
2-3 short For 100MHz Normal (Default).
t J11: Internal Modem Card RING PWR ON
Pin Function
1 Signal
Hardware Installation
3-5
2 GND
t SB-LINK (For PCI Sound Card Connector) (Optional)
Pin Function
1 Signal
2 GND
3 NC
4 Signal
5 GND
6 Signal
t JP10 : CASE OPEN Function (Optional)
Pin Function
1 Signal
2 GND
t TEL:The Connector is for Modem with internal Voice connector(Optional)
Pin Function
1 Signal-In
2 GND
3 GND
4 Signal-Out
t CN6 : CD Audio Line In (Optional)
Pin Function
1 GND
2 Right
3 GND
4 Left
t JP5 : CD Audio Line In (Optional)
Pin Function
1 Right
2 GND
3 GND
4 Left
6ZMA/6ZM
3-6
t JP5 : CD Audio Line In (Optional)
(This function is support in PCB version 1.2 and above)
Pin Function
1 Left
2 GND
3 GND
4 Right
t JP21 : Internal Buzzer Connector
(This function is support in PCB version 1.2 and above)
Pin Function
1-2 Short BZ1 Enable(Default)
Open BZ1 Disable
JP6 : For 2X11 PINs Jumper
PW: Soft Power Connector
Open: Normal Operation
Short: Power On/Off
RST: Reset Switch
Open: Normal Operation
Short: For Hardware Reset System
P+P−P−: Power LED
PIN 1 : anode (+)
PIN 2 : cathode (−)
PIN 3 : cathode (−)
1
PW P+P−P−
HD
RST
S P K
GN
GD
JP6
1
1 1
1
Hardware Installation
3-7
SPK: Speaker Connector
PIN 1 : VCC (+)
PIN 2 : VCC
PIN 3 : Data
PIN 4 : Data (−)
SPK : Internal Speaker Connector (Default)
PIN 1 : VCC (+)
PIN 2-PIN3 : Short
PIN 4 : Data (−)
HD: IDE Hard Disk Active LED
PIN 1: LED anode (+)
PIN 2: LED cathode (−)
GN: Green Function Switch
Open : Normal operation
Short : Entering Green Mode
GD: Green LED
PIN 1 : LED anode (+)
PIN 2 : LED cathode (−)
3.4. DRAM INSTALLATION
The mainboard can be installed with 16 / 32 / 64 / 128 / 256 MB 168 pins
DIMM module DRAM, and the DRAM speed must be 67~100 MHz for
SDRAM. The DRAM memory system on mainboard consists of bank 0 ,
bank 1.
Since 168 pins DIMM module is 64 bits width, using 1 PCS which can match
a 64 bits system. The total memory size is 16MB ~ 256MB SDRAM. The
DRAM installation position refer to Figure 3.1, and notice the Pin 1 of DIMM
1
1
1
+
−
1
+
−
6ZMA/6ZM
3-8
module must match with the Pin 1 of DIMM socket. Insert the DRAM DIMM
module into the DIMM socket at Vertical angle. If there is a wrong direction
of Pin 1, the DRAM DIMM module couldn't be inserted into socket
completely.
3.5. CPU SPEED SETUP
The default system bus speed is 66 / 100MHz (SW2). The user can change
the DIP SWITCH (SW1) selection to set up the CPU speed for 233 - 650MHz
processor. The CPU speed must match with the frequency RATIO. It will
cause system hanging up if the frequency RATIO is higher than CPU's.
SW1:
CLK RATIO 1 2 3 4
X3 ON OFF ON ON
X3.5 OFF OFF ON ON
X4 ON ON OFF ON
X4.5 OFF ON OFF ON
X5 ON OFF OFF ON
X5.5 OFF OFF OFF ON
X6 ON ON ON OFF
X6.5 OFF ON ON OFF
X 7 ON OFF ON OFF
X 7.5 OFF OFF ON OFF
X 8 ON ON OFF OFF
X 8.5 OFF ON OFF OFF
X 9 ON OFF OFF OFF
X 9.5 OFF OFF OFF OFF
SW2:
CPU 1 2 3 4
66 ON OFF OFF ON
75 ON ON OFF ON
83 ON OFF ON ON
100 OFF OFF OFF OFF
112 OFF ON OFF OFF
Hardware Installation
3-9
133 OFF OFF ON OFF
DIP SWITCH (SW1)
1 2 3 4
FREQ.
RATIO
EXT.CLK.
MHz
INT.CLK.
MHz
CPU Type
OFF OFF ON ON 3.5 66 233
Pentium II 233 MHz
(Celeron 233MHz)
ON ON OFF ON 4 66 266
Pentium II 266 MHz
(Celeron 266MHz)
OFF ON OFF ON 4.5 66 300
Pentium II 300 MHz
(Celeron 300MHz)
ON OFF OFF ON 5 66 333
Pentium II 333 MHz
(Celeron 333MHz)
OFF OFF OFF ON 5.5 66 366
Pentium II 366 MHz
(Celeron 366MHz)
ON ON ON OFF 6 66 400
Pentium II 400 MHz
(Celeron 400MHz)
OFF ON ON OFF 6.5 66 433
Pentium II 433 MHz
(Celeron 433MHz)
OFF OFF ON ON 3.5
100
350
Pentium II 350 MHz
ON ON OFF ON 4
100
400
Pentium II 400 MHz
OFF ON OFF ON 4.5
100
450
Pentium III 450 MHz
ON OFF OFF ON 5
100
500
Pentium III 500 MHz
OFF OFF OFF ON 5.5
100
550
Pentium III 550 MHz
ON ON ON OFF 6
100
600
Pentium III 600 MHz
OFF ON ON OFF 6.5
100
650
Pentium III650 MHz
♦
The CPU is a sensitive electric component and it can be easily
damaged by static electricity, so users must keep it away from
metal surface when the CPU is installed onto mainboard.
♦
Note: It’ s strongly recommended that set the system speed
according to your hardware configuration: CPU, SDRAM, Cards,
etc.
3.6. CMOS RTC & ISA CFG CMOS SRAM
The mainboard contains RTC & CMOS SRAM on board. They have a power
supply from external battery to keep the DATA inviolate & effective. The RTC
is a REAL-TIME CLOCK device, which provides the DATE & TIME to
6ZMA/6ZM
3-10
system. The CMOS SRAM is used for keeping the information of system
configuration, so the system can automatically boot OS every time. Since
the lifetime of internal battery is 5 years, the user can change a new Battery
to replace old one when it has consumed.
3.7. SPEAKER CONNECTOR INSTALLATION
There is a speaker in AT system for sound purpose. The 4 - Pins connector
SPK is used to connect speaker. Anode connects +, Cathode connects −.
3.8. HARDWARE RESET SWITCH CONNECTOR INSTALLATION
The RESET switch on panel provides users with HARDWARE RESET
function. The system will do a cold start after the RESET switch is press and
released by user. The RESET switch is a 2 PINS connector and should be
installed to RES on mainboard.
3.9. POWER LED CONNECTOR INSTALLATION
System has power LED lamp on the panel of case. The power LED will light
on off or flash to indicate which step on the system. The connector should be
connected to LED of mainboard in correct direction.
3.10. IDE & ATAPI DEVICE INSTALLATION
There are two-Enhanced PCI IDE ports (IDE1, IDE2) on board, which
following ATAPI standard SPEC. Any one IDE port can connected to two
ATAPI devices (IDE Hard Disk, CD-ROM & Tape Driver), so total four ATAPI
devices can exist in a system. The HD is the active LED port for ATAPI
devices.
3.11. PERIPHERAL DEVICE INSTALLATION
After the I/O device installation and jumpers setup, the mainboard can be
mounted into the case and fixed by screw. To complete the mainboard
installation, the peripheral device could be installed now. The basic system
needs a display interface card. If the PCI - Bus device is to be installed in the
Hardware Installation
3-11
system, any one of three PCI - Bus slots can be used.
3.12.PS/2 KEYBOARD & MOUSE INSTALLATION
The main board supports PS/2 Mouse. The BIOS will auto detect whether the
PS/2 Mouse is installed or not & assign IRQ12 for PS/2 Mouse port if it is
installed. After installing the peripheral device, the user should check
everything again, and prepare to power-on the system.
Loading...