Giant Telecom OL2430 User Manual
Giant -309 Operation Manual (2.4GHz Cordless + CID)
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire.
They may explode. Check with local codes for possible special disposal instructions.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
SAVE THESE INSTRUCTIONS
Revision 1
Page1of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
Allows the user to answer a call by just removing the handset from the base so the user don’t have to waste
MAIN FEATURES
OLYMPIA OL2430 CORDLESS PHONE FEATURES :
1. 2.4GHz 40 channels auto scanning operation
2. Manual channel selection
3. 65536 Random combinations of security code
4. Last number re-dial (32 digits max.)
5. Power saving in standby mode. ( handset )
6. Page in base unit to locate the handset ( short and long page )
7. Temporary touch tone (pulse to tone dialing)
8. Tone / Pulse dialing mode selection in handset
9. Ringer ON /OFF selection in handset
10. Mixed mode dialing (auto insert of 4 sec. pause when mode change from Pulse to Tone)
11. 10 indirect memories store in handset (16-digits / phone no.)
12. Chained memory dialing of 32 digits max.
13. Flash key for call waiting and call transfer 600ms.
14. Handset LED for paging, ringing and on cradle (Enabled by setup menu)
15. Receiver volume control by software (Three level default at middle level)
16. Pause key ( pause time is 4 seconds )
17. Low battery warning tone
18. Handset ringing
19. Back-lighted LCD
20. Auto Standby feature
21. Auto Answer connection
22. Any key answer
23. Direct number dial out
24. Memory direct dial out
25. Direct redial
26. Redial & CID transfer to in-direct memory ( 16 digits long )
Auto Standby Allows the user to hang up by simply returning the handset to the base.
Auto Answer
time pushing buttons. The ‘Talk” key will be disabled for 5 seconds to avoid accidental hang up. This
feature is activated while ringing and disable 5 seconds after the ring.
CALLER ID FEATURES :
1 Type I + Type II (call waiting)
2 64 name and number caller ID
3 3-line display
4 back-lit LCD (on handset)
5 Total call counter
6 New call LED indicator in handset
7 Repeat call indication (LCD icon)
8 3-language operation (English, Spanish & French)
9 Scroll review of CID records
10 Selective-erase / Erase-all function
11 Real time clock (date & time)
12 Private/ out-of-area indication
13 LCD contrast control 6 levels, default at 3.
14 Call back (CID dial back)
Revision 1
Page2of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
15 Battery low indication (‘Battery Low’ text display on the 3rd line )
CORDLESS OPERATION
Channel frequencies
CH.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
BASE TX H/S TX
2401000000 2473500000
2401100000 2473600000
2401200000 2473700000
2401300000 2473800000
2401400000 2473900000
2401500000 2474000000
2401600000 2474100000
2401700000 2474200000
2401800000 2474300000
2401900000 2474400000
2402000000 2474500000
2402100000 2474600000
2402200000 2474700000
2402300000 2474800000
2402400000 2474900000
2402500000 2475000000
2402600000 2475100000
2402700000 2475200000
2402800000 2475300000
2402900000 2475400000
CH.
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
BASE TX HS/TX
2403000000 2475500000
2403100000 2475600000
2403200000 2475700000
2403300000 2475800000
2403400000 2475900000
2403500000 2476000000
2403600000 2476100000
2403700000 2476200000
2403800000 2476300000
2403900000 2476400000
2404000000 2476500000
2404100000 2476600000
2404200000 2476700000
2404300000 2476800000
2404400000 2476900000
2404500000 2477000000
2404600000 2477100000
2404700000 2477200000
2404800000 2477300000
2404900000 2477400000
Revision 1
Page3of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
1. Power Up
1.1. After power up, the handset should place on the cradle of the base unit for setting a new
security code for communication
1.2. Each time when the handset place on the cradle of the base unit, the base unit will generate
and transmit a new security code to the handset unit through the RF Link.(The both unit will
use the 1st channel for the security code transfer operation)
1.3. The completion of a successful security code transfer operation will be indicated by a flash
of the in use LED on the base unit and a beep sound generated by handset.
1.4. In case, the Transfer operation cannot be successful, please try again.
2. Answering Call
2.1. The incoming call is signaled by a ringing sound from the handset’s buzzer and by the
blinking of the base In use/Charge LED. At the same time ‘RINGING’ will be shown in the
display. The handset LED will be turned on during ringing
2.2. When the handset on the cradle, simply pick up the handset unit from the cradle of the base
to talk. The “TALK” button will be disabled for 5 seconds.
2.3. When the handset is away from the base unit, press the “TALK” button on the handset unit.
The handset will transmit the “talk on” command to base unit to establish the RF connection
with in use/charge LED turns on after connection is successful.
2.4. If the communication Link cannot establish within 8 seconds, three error beeps tone will be
heard from the handset to indicate communication is failed.
3. Make a call
3.1. Each new call must begin by pressing the “TALK” button in the handset and it will scanning
for a clear channel for communication. At the same time, ‘TALK’ will be shown on LCD
display. The handset will transmit the “talk on” command to the base unit to establish the
RF communication after connection is successful.
3.2. If the communication Link cannot establish within 8 seconds, there error beeps tone will be
heard from the handset to indicate the communication is failed.
Revision 1
Page4of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
4. Terminate a call
4.1. To terminate a call, either by pressing the “TALK” button, the handset will emit a beep
indicating call is terminated successfully.
4.2. By placing the handset on the cradle, call is terminated and ‘Security code set up’ procedure
will be performed.
4.3. Handset will emit a error beep if it cannot receive ‘talk off ACK’ from the base unit. In this
case, put the handset back to the base cradle to make sure base unit is going ON HOOK.
5. Short Paging (to locate the Handset)
5.1. Press the PAGE button of the base unit. The ‘PAGING’ will be shown on the LCD display
and output 3 short beeps then followed by 1 second pause, followed by 3 short beeps. The handset LED
will be turned on during paging.
6. Long Paging (to find the handset)
6.1. Press the PAGE button of the base unit. The ‘PAGING’ will be shown on the LCD display
and output beep. If you hold the button for 5sec, the beep will be extended to 60sec. The
handset LED will be turned on during paging.
6.2. Press any key on handset to stop paging.
7. Selecting system language
7.1. Two cases you enter the system setup mode.
1) The handset is first time use or no any system data after power up.
2) Press and hold the ‘memory’ key for about 2sec in stand-by.
7.2. Setup mode begins with language selection. The device offers 3 languages, namely English,
French and Spanish. Press “#” or “*” button to choose the desired language and then press
the “MEMO” key to confirm. After confirmation, it will enter Setting local area code
S E T L A N G U A G E
Revision 1
Page5of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
8. Setting local area code
8.1. You need enter 3 digits from number pad. Three digits will be shift to left one by one, after
you enter one digit.
E.g. [Press “1”, display “ 001”] à [Press “2”, display “012”] à [Press “3”, display “123”]
8.2. Press “MEMO” key to confirm. After confirmation, it will enter Tone/Pulse setting.
0 0 0
A R E A C O D E ?
9. Setting Tone/Pulse
9.1. It will display current T/P setting first
9.2. Press “#” or “*” button to set the desired setting, and the display will update to current
setting also, ”SET T/P? T”à” SET T/P? P”à”SET T/P? T”……..
9.3. Press “MEMO” key to confirm. After confirmation, It will enter ringer setting.
S E T T / P ? T
10. Setting RINGER ON/OFF
10.1. It will display current RINGER ON/OFF setting first
10.2. Press “#” or “*” button to set the desired setting, and the display will update to current setting
also, ”RINGER ON”à” RINGER OFF”à”RINGGER ON”……..
10.3. Press “MEMO” key to confirm. After confirmation, It will enter LED setting.
Revision 1
R I N G E R O N
Page6of22
Giant -309 Operation Manual (2.4GHz Cordless + CID)
88
RPT
18:88
1 8/8 8
indicator
age
VIP
11. Setting handset LED ON/OFF/CON
11.1. It will display current “LED ON/OFF/CON” setting first.
11.2. Press “#” or “*” button to set the desired setting, and the display will update to current setting
also, ”LED ON”à” LED OFF”à”LED CON”à ”LED ON”……..to control the handset
LED.
11.3. Press “MEMO” key to confirm. After confirmation, It will enter display contrast setting.
L E D O N
12. Setting display contrast
12.1. Two cases you can enter contrast setting.
1) From system setup mode.
2) Press “FLASH” button in stand-by.
12.2. Press “#” or “*” button to set the desired contrast.
12.3. Press “MEMO” key to confirm. After confirmation, display returns to standby.
* Press ‘CHANNEL’ button to return to stand-by.
C O N T R A S T 5 6
13. CALLER ID OPERATION
Display :
Revision 1
Repeated-call
New-Call /
Call counter
NEW
CALL
1 2 3 4 5 6 7 8 9 0 1 2
ttA B C D E F G H I J K L uu
New
voice-mess
Clock
NEW CALL
INDICATOR
Clock ticker
12-character text line (dot matrix) 12-digit number line (7-segment)
Date
Page7of22
Loading...