Page 1
Quick Start Guide
GV-Video Server
Thank you for purchasing GV-Video Server. This guide is designed to assist the new user
in getting immediate results from the GV-Video Server. For advanced information on how to
use the GV-Video Server, please refer to GV-Video Server User's Manual on Software
DVD.
© 2016 GeoVision Inc. All rights reserved.
2016/03
English
VS2420-2400-QG-A
Page 2
1
Introduction
Welcome to the GV-Video Server Quick Start Guide. In the following
sections, you will learn about the basic installations and configurations of the
GV-Video Server (VS04H / VS11 / VS12 / VS14 / VS2420 / VS2400).
For a detailed user’s manual, see GV-Video Server User’s Manual on the
GV-Video Server software CD/DVD.
Packing List
GV-VS04H / GV-VS14
● GV-VS04H / GV-VS14
● 3.5 mm Stereo to RCA Cable x 2
● DC Male-to-Male Cable x 1
● AC Power Cord x 1
● Conical Anchor x 4
● Screw x 4
● GV-Video Server Software CD/DVD x 1
● GV-NVR Software CD/DVD x 1
Note: The DC Male-to-Male Cable is
used to power on the camera through
the GV-Video Server. You can also
optionally purchase three more DC
Male-to-Male Cables and one DC
1-Male to 4-Female Cable to power on
four cameras through the GV-Video
Server.
● Power Adaptor x 1
● Wall Hook x 1
DC 1-Male to
4-Female Cable
DC Male-to-Male
Cable
Page 3
GV-VS11
● GV-VS11
● Power Adaptor x 1
● GV-Video Server Software CD/DVD x 1
● GV- NVR Software CD/DVD x 1
GV-VS12
● GV-VS12
● I/O Cable with RJ-45 Connector x 1
● Sticker (for positioning conical anchors) x 1
● AC Power Cord x 1
● Power Adaptor x 1
● Wall Hook x 1
● Screw x 4
● Conical Anchor x 4
● GV-Video Server Software CD/DVD x 1
● GV-NVR Software CD/DVD x 1
GV-VS2420 / 2400
● GV-VS2420/2400
● AC Power Cord x 1
● Power Adaptor x 1
● GV-Video Server Software CD/DVD x 1
● GV-NVR Software CD/DVD x 1
● Warranty Card
Page 4
Options
GV-GPS Receiver
GV-Relay V2
GV-WiFi USB Adaptor
GV-PA191 PoE Adaptor
GV-VR605A DC Voltage
Regulator
The GV-GPS Receiver is a Global Position
System receiver. With the GV-GPS Receiver,
you can perform GPS tracking and location
verification of the GV-Video Server. Two types
of interfaces are available: UART (for
GV-VS04H / GV-VS14) and RS-232 (for
GV-VS12).
Note: The GV-GPS Receiver is not supported
by GV-VS11 and GV-VS2420 / 2400.
Working with the GV-Relay V2, the GV-Video
Server is capable of driving the loads of relay
outputs over 5 volts.
The WiFi USB Adaptor is designed to connect
the GV IP devices, such as GV-Video Server or
GV-Compact DVR, to the wireless network.
The GV-PA191 is designed to provide power to
the IP device through a single Ethernet cable.
The GV-PA191 is only supported by GV-VS04H,
and GV-VS12.
With the GV-VR605A, you can install GV-Video
Server in the car. The GV-Video Server will
supply and maintain a 12V voltage to the
GV-Video Server and its connected cameras.
Note: The GV-VR605A is not supported by
GV-VS2420 / 2400.
Page 5
DC Male-to-Male Cable/
DC 1-Male to 4-Female
Cable
Only supported by GV-VS2420 / 2400, the DC
Male-to-Male Cable is used to power on the
camera through the GV-Video Server.
For instance, you can purchase four DC
Male-to-Male Cables and one DC 1-Male to
4-Female Cable to power on four cameras
through the GV-Video Server.
3.5 mm Stereo to
RCA Cable
Wall Hook
Din-rail Hook
Access Control Series
The GV-Video Server can work with the Wiegand-interface card reader to
send cardholder data to the central monitoring stations Center V2 and
VSM, as well as GV-System (GV-DVR / NVR). The following devices are
only supported by GV-VS04H and GV-VS14.
GV-Reader
GV-R1352 Card Reader
Only supported by GV-VS2420 / 2400, the 3.5
mm Stereo to RCA Cable is served as an audio
adapter for microphones with RCA connectors.
Only supported by GV-VS2420 / 2400, the Wall
Hook is used to mount the device to the wall.
Only supported by GV-VS2420 / 2400, the
Din-rail Hook is used to mount the device to a
cabinet.
GV-Reader includes transmit-receive antenna
and electronics. Featured with both Wiegand
and RS-485 outputs, the unit is compatible with
any standard access control panel.
The GV-R1352 is a card reader designed to
recognize identification cards. Featured with the
Wiegand and RS-485 outputs, the unit can be
connected to any standard access control panel.
The GV-R1352 comes with a weather sealed
and IP66 compliant housing for outdoor use.
Page 6
2
Overview
GV-VS04H / GV-VS14
Front View
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Rear View
9
10 11 12 13
Page 7
No.
Name
1
Video Input
2
Speaker Output
3
Audio Input
4
Default Button
5
Disk Full/Fault LED
6
Ready LED
7
Power LED
8
Reset
9
USB Port
10
Terminal Block
11
Ethernet Port
12
Power Out
Function
4 plugs for video inputs.
A plug for the speaker device.
Each plug is for 2 audio inputs.
It resets all configurations to their factory
settings. See 7 Restoring to Default Settings in
the Quick Start Guide.
This LED is on, indicating the hard drive is full
or faulty.
This LED is on, indicating the GV-Video Server
is ready for connection.
This LED is on, indicating the power is
supplied.
It reboots the GV-Video Server, and keeps all
current configurations.
2 USB ports for installing portable storage
devices.
The connectors for digital input, relay output,
PTZ camera, Wiegand device and GPS module
control.
A plug for a 10/100 Ethernet or PoE.
Note: GV-VS14 does not support PoE function.
A plug to power on the camera, by using a DC
Male-to-Male Cable, directly through the
GV-Video Server.
Note: When PoE is applied, you cannot power
on the camera through the GV-Video Server.
13
Power In
A plug to power on the GV-Video Server.
Page 8
GV-VS11
No.
Name
1
Video Input
2
Default Button
3
Audio Input
4
Ready LED
5
Power LED
6
USB Port
7
Ethernet Port
8
Terminal Block
9
Power In
Rear ViewFront View
1 2 3 4 6 7 8 95
Function
1 plug for video input.
It resets all configurations to their factory
settings. See 7 Restoring to Default Settings in
the Quick Start Guide.
1 plug for audio input.
This LED is on, indicating the GV-Video Server
is ready for connection.
This LED is on, indicating the power is
supplied.
1 USB port for installing portable storage
device.
A plug for inserting an Ethernet cable to build
the network connection.
The connectors for digital input, digital output
and PTZ camera control.
A plug to power on the GV-Video Server.
Page 9
GV-VS12
Front View
1 3
2 4
Rear View
5 6
7 8 9
10 11 12
Page 10
Name
No.
USB Port
1
2
Speaker Output
3
Audio Input
4
Video Input
5
Power In
6
Ethernet Port
7
USB Port
8
I/O / PTZ Port
9
RS-232
Terminal Block
10
Default Button
11
Ready LED
12
Power LED
Function
1 USB port for installing the portable storage
device.
A plug for the speaker device.
2 plugs for audio inputs.
2 plugs for video inputs.
A plug to power on the GV-Video Server.
A plug for inserting an Ethernet cable to build
the network connection.
1 USB port for installing the portable storage
device.
A port for digital input, relay output and PTZ
camera control. Insert the I/O Cable with RJ-45
Connector to this port.
The connectors for GPS module control.
It resets all configurations to their factory
settings. See 7 Restoring to Default Settings in
the Quick Start Guide.
This LED is on, indicating the GV-Video Server
is ready for connection.
This LED is on, indicating the power is
supplied.
Page 11
GV-VS2420 / 2400
8
7
6
4
Front View
No.
Name
1
Video Input
2
Line Out
3
Line In
4
Reset
5
Default Button
6
Disk Full/Fault LED
7
Ready LED
5
9 10 11 12 13
Function
4 plugs for video inputs.
A plug for Video 1 speaker device.
A plug for Video 1 audio input.
It reboots the GV-Video Server, and keeps all
current configurations.
It resets all configurations to their factory
settings. See 6.4 Restoring to Factory Default
Settings.
This LED is on, indicating the hard drive is full
or faulty.
This LED is on, indicating the GV-Video Server
is ready for connection.
1
Rear View
2 3
Page 12
8
Power LED
This LED is on, indicating the power is
supplied.
USB Port
9
Terminal Block
10
Gigabit Ethernet
11
Port
Power Out
12
Power In
13
Note: When transmitting video signals over a long distance, it is highly
recommended to use 5C-FB coaxial cables or above to minimize the
degradation of image quality. The transmission distance should be
within 300 m (984 ft).
2 USB ports for installing portable storage
devices.
The connectors for digital input, relay output,
and PTZ camera. See Chapter 9 Auxiliary
Device Connectors.
A plug for a 10/100/1000 Base-T Ethernet
A plug to power on the camera, by using the
optional DC Male-to-Male Cable, directly
through the GV-Video Server.
A plug for power input.
Page 13
3
Installing on a Network
Here we use GV-VS04H as an example to demonstrate the basic
connections.
1
3
1. Connect your camera’s video output to the BNC video input.
2. Connect the microphone to the RCA audio input using the 3.5 mm
Stereo to RCA Cable.
3. Connect the hub or switch on the LAN to the unit’s 10/100 Mbps port.
4. Connect power using one of the following methods:
● Use the supplied power adapter, connect to power.
● Use the Power over Ethernet (PoE) function. The power is
provided over the network cable.
5
2
4
Page 14
5. Optionally connect the DC Male-to-Male Cable to power on the camera
through the GV-Video Server.
6. Wait until both Power and Ready LEDs are on and then you can
access its Web interface. See 4. Accessing the Camera later in the
Quick Start Guide.
Note:
1. The GV-VS11 / 14 and GV-VS2420 / 2400 do not support PoE function.
2. The DC Male-to-Male Cable and 3.5 mm Stereo to RCA Cable are only
supplied for GV-VS04H and GV-VS14. Optionally purchase these
accessories for GV-VS2420 / 2400.
3. The GV-Video Server cannot work with the microphone requiring power
from the unit. Use the microphone that has external power supply.
4. When PoE is applied, you cannot power on the camera through the
GV-Video Server.
Page 15
4
Accessing the GV-Video Server
System Requirements
To access the Web interface of the GV-Video Server, ensure your PC is in
goodnetwork connection and use one of the following Web browsers:
For GV-VS04H and GV-VS11 / 12 / 14
● Microsoft Internet Explorer 7.x or later
For GV-VS2420 / 2400
● Microsoft Internet Explorer 8.x or later
● Google Chrome
● Mozilla Firefox
● Safari
● Microsoft Edge
Note:
1. For the users of Internet Explorer 8 or later, additional settings are
required. For details, see Appendix A in GV-Video Server User’s
Manual on the software CD/DVD.
2. Internet Explorer 10 is only supported by GV-VS11 version 1.05,
GV-VS12 version 1.09, GV-VS14 version 1.03.
3. For users of non-IE browsers using GV-VS2420 / 2400, download
GV-Web Viewer to access full functioning user interface. For details,
see 3.1 Accessing Your Surveillance Images in GV-Video Server
User’s Manual on the software CD/DVD.
Page 16
Checking the IP Address and Logging In
By default, the IP address of your GV-Video Sever is assigned by the DHCP
server unless your router does not support DHCP. In this case, the default
IP address will be 192.168.0.10. Follow the steps below to look up the IP
address and access the Web interface.
1. Install the GV-IP Device Utility program included on the Software
CD/DVD.
Note: The PC installed with GV-IP Device Utility must be under the
same LAN with the GV-Video Server you wish to configure.
2. On the GV-IP Utility window, click the button to search for the IP
devices connected in the same LAN. Click the Name or Mac Address
column to sort.
Page 17
3. Find the GV-Video Server with its Mac Address to see the IP address.
4. To login, type the IP address in your web browser. A dialog box
appears.
5. Type the default username and password admin.
6. Click OK to access the Web interface.
7. When accessing the GV-Video Server for the first time, you must set
your browser to allow a one-time installation of GeoVision’s ActiveX
component onto your computer.
Note:
If your router does not support DHCP, the default IP address will
be 192.168.0.10. In this case, it is strongly suggested to modify the IP
address to avoid IP address conflict with other GeoVision IP device on
the same LAN. For details, see 2.3 Changing the IP Address, GV-Video
Server User’s Manual on the Software CD/DVD.
Page 18
5
The Web Interface
1 2 3 4 5 6 7 8
12
11
10
9
Page 19
Name
No.
Play
1
Stop
2
Microphone
3
Speaker
4
Snapshot
5
File Save
6
Full Screen
7
Control Panel
8
I/O Control
9
PTZ Control
10
Change Camera
11
Show System Menu
12
Function
Plays live video.
Stops playing video.
Talks to the surveillance area from the local
computer.
Listens to the audio around the camera.
Takes a snapshot of live video.
Records live video to the local computer.
Switches to full screen view. Right-click the
image to have these options: Snapshot, PIP,
PAP, Zoom In and Zoom Out.
Displays the camera information, video
settings, audio data rate, I/O device status,
images captured upon alarm, and GPS location
of the camera.
Starts the I/O Control Panel or the Visual
Automation.
Starts the PTZ Control Panel and the Visual
PTZ.
Sets the desired camera for display.
Brings up these functions: Alarm Notify, Video
and Audio Configuration, Remote Config,
Show Camera Name and Image Enhance.
For detailed operations, see Accessing the GV-Video Server, Chapter 3,
GV-Video Server User's Manual on the software CD/DVD.
Page 20
6
Upgrading System Firmware
GeoVision will periodically release the updated firmware on the website. To
load the new firmware into the GV-Video Server, read the important notes
below and then follow the instructions.
Important:
1. While the firmware is being updated,
A) the power supply must not be interrupted, and
B) do not unplug the Ethernet cable if the cable is the source of
power supply (Power over Ethernet or PoE supported).
2. Do not turn the power off within 10 minutes after the firmware is
updated.
3. If you use the IP Device Utility for firmware upgrade, the computer
used to upgrade firmware must be under the same network of the
GV-Video Server.
Page 21
1. In the Live View window, click the Show System Menu button and select
Remote Config. This dialog box appears.
2. Click the Browse button to locate the firmware file (.img) saved at your
local computer.
3. Click the Upgrade button to start the upgrade.
WARNING: The interruption of power supply during updating causes
not only update failures but also damages to the camera. In this case,
please contact your sales representative and send your device back to
GeoVision for repair.
For details on upgrading system firmware, see Advanced Applications,
Chapter 6, GV-Video Server User's Manual on the software CD/DVD.
Page 22
7
Restoring to Default Settings
You can restore the camera to factory default settings using the Web
interface or directly on the GV-Video Server.
Using the Web Interface:
1. On the left menu of Web interface, select Management and select
Tools. The Additional Tools dialog appears.
2. Click the Load Default button in the System Settings section.
Page 23
Directly on the GV-Video Server:
GV-VS04H / GV-VS14
2 1 4
1. Press and then release the Reset button immediately.
2. Press and hold the Load Default button until all 3 LEDs (Power,
Ready and Disk Full/Fault) are on. This may take about 30 seconds.
3. Release the Load Default button. The process of loading default
values is complete, and the GV-Video Server starts rebooting itself
with all 3 LEDs turning off.
4. Wait until the Power and Ready LEDs turn on again. After this, all the
settings are returned to default values.
Page 24
GV-VS11
2 4
GV-VS12
2 4
1. Unplug and plug the power cable to start.
2. Press and hold the Default button until the Ready LED blinks. This
may take about 30 seconds. The Ready LED will blink twice.
3. Release the Default button. The process of loading default values is
complete, and the GV-Video Server starts rebooting itself with the 2
LEDs turning off.
4. Wait until the Power and Ready LEDs turn on again. After this, all the
settings are returned to default values.
Page 25
GV-VS2420 / 2400
4
5
1. Press and then release the Reset button immediately.
2. Press and hold the Default button until the Ready LED blinks. This
may take up to 30 seconds. The Ready LED will blink twice.
3. Release the Default button. The process of loading default values is
complete, and the GV-Video Server starts rebooting itself with the
Ready LED turning off.
4. Wait until the Ready LED turns on again. After this all the settings are
returned to default values
Note: Before the Ready LED is on again, do not unplug the power
cable; otherwise the loading of default values will fail.
Page 26
8
Connecting Auxiliary Devices
GV-VS04H / GV-VS14 and GV-VS2420 / 2400
GV-VS04H and GV-VS14
The 16-pin terminal block, located on the rear panel, provides interfaces for
four digital inputs, four relay outputs, an RS-485 interface, a Wiegand
interface, a GPS interface and auxiliary power. The terminal block can be
used to develop applications for motion detection, event alerts via E-mail and
FTP, center monitoring by Center V2 and Vital Sign Monitor, PTZ control,
Wiegand-interface card reader and a variety of other functions.
GV-VS2420 / 2400
The 16-pin terminal block, located on the rear panel, provides interfaces for
four digital inputs, four relay outputs, an RS-485 interface and auxiliary
power. The terminal block can be used to develop applications for motion
detection, event alerts via E-mail and FTP, center monitoring by Center V2
and Vital Sign Monitor, PTZ control and a variety of other functions.
162 4 6 8 10 12 14
151 3 5 7 9 11 13
Page 27
Pin Assignment
The table below lists the pin assignment for the terminal block.
GV-VS04H and GV-VS14
Function
Pin
Relay Output 1
1
Digital Input 1
2
Relay Output 2
3
Digital Input 2
4
Relay Output 3
5
Digital Input 3
6
Relay Output 4
7
Digital Input 4
8
Note: To connect the GPS module, use the Pin 9 for power supply, Pin
10 for ground, Pin 12 for GPS RX and Pin 14 for GPS TX.
GV-VS2420 / 2400
Function
Pin
Relay Output 1
1
Digital Input 1
2
Relay Output 2
3
Digital Input 2
4
Relay Output 3
5
Digital Input 3
6
Relay Output 4
7
Digital Input 4
8
Function
Pin
DC 5V Out for GV-Relay Module, or GPS Module
9
Ground, or GPS Ground
10
RS 485+
11
Wiegand D0, or GPS RX
12
RS 485-
13
Wiegand D1, or GPS TX
14
Ground
15
DC 12V Out for Wiegand Card Reader
16
Function
Pin
DC 5V Out for GV-Relay Module
9
Ground
10
RS 485+
11
N/A
12
RS 485-
13
N/A
14
Ground
15
DC 12V Out
16
Page 28
GV-VS11
The terminal block on the rear panel of GV-VS11 provides one digital input
and output, an RS-485 interface and auxiliary power.
- + 5V
Pin Assignment
The table below lists the pin assignment for the terminal block.
Pin
RS-485-
RS-485+
5V
DI
DO
G
Function
RS-485-
RS-485+
DC 5V Out
Digital Input
Digital Output
Ground
DI DO G
Page 29
GV-VS12
GV-VS12 provides the I/O Cable with RJ-45 Connector for the extensible
connection to I/O devices and PTZ cameras. A RJ-45 connector and a
bundle of shielded wires are on the each end of the cable.
Pin Assignment
The table below lists the pin assignment for the shielded wires of the I/O
Cable with RJ-45 Connector.
Wire
Pin
Brown
1
White with Brown Stripe
2
White with Green Stripe
3
White with Blue Stripe
4
Blue
5
Green
6
Orange
7
White with Orange Stripe
8
Function
Digital Out 1
Digital Out 2
Ground
Digital In 1
Digital In 2
Ground
RS-485 -
RS-485 +
Page 30
RS-232 Terminal Block
The RS-232 terminal block on GV-VS12 is mainly used for the connection to a
GPS module.
RS232
Function
Pin
GPS RX (Receive)
TX
GPS TX (Transmit)
RX
Ground
G
DC 5V Out
5V
TXRXG
5V
Note: To ensure the connection to the GV-VS12, the GPS RX must be
connected to the TX pin, and the GPS TX must be connected to the RX
pin.
For details, see Auxiliary Device Connectors, Chapter 9, GV-Video Server
User's Manual on the software CD/DVD.
9F, No. 246, Sec. 1, Neihu Rd., Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8376 Fax: +886-2-8797-8335
support@geovision.com.tw
http://www.geovision.com.tw
Loading...