Geovision GV-POEX0100 Installation Guide
GV-POEX0100 One-Port PoE Extender
GV-POEX0100 is a single-port, 10/100 PoE extender that can extend the distance between a
PoE switch and a GV-IP Camera by 100 m (328.08 ft) for every extender installed. They can
be serially connected, with no additional power supply, to transmit power and data to a GV-IP
Camera as far as up to 600 meters (1968.5 ft) away from a PoE switch.
Requirements and Limitations
The maximum distance allowed between a PoE switch and a GV-IP Camera depends on the
PoE switch type, PoE power output of the connected device (PD) and the type of power
supply. These can be summarized below.
GV-IP Cameras Powered by PoE
Brand & Model
PD of GV-IP Cameras
PD < 6.49 W
(IEEE 802.3af)
PD 6.5 W ~ 12.95 W
(IEEE 802.3af)
GV-POE0801 / 0811
GV-POE0812
GV-POE1601 / 1611
GV-POE2401 / 2411
600 m (1968.5 ft) 400 m (1312.34 ft) 400 m (1312.34 ft)
400 m (1312.34 ft) 200 m (656.17 ft) 200 m (656.17 ft)
GeoVision
GV-POE0400
GV-POE0410-E
GV-POE0800
GV-POE0810
Third-Party PoE
Switches
(IEEE 802.3at)
PD 13 W ~ 25.5 W
(IEEE 802.3at)
PD > 25.5 W - - Note:
1. Each GV-POEX0100 extends another 100 m (328.08 ft) between the PoE switch and
2. GV-POE0100 can only be connected using CAT-5e cables, TIA/EIA-568-B, with the
GV-IP Cameras Powered by Power Adapters
June 16, 2016
200 m (656.17 ft) - -
the GV-IP Camera. Therefore, a distance of 200 m (656.17 ft) requires one GVPOEX0100 and 400 m (1312.34 ft) requires three etc.
maximum DC resistance of 9.38 ohms/100 m.
1
GeoVision
GV-POE0801 / 0811
Brand & Model
GV-IP Cameras 600 m (1968.5 ft) 400 m (1312.34 ft) 400 m (1312.34 ft)
GV-POE0812
GV-POE1601 / 1611
GV-POE2401 / 2411
GV-POE0400
GV-POE0410-E
GV-POE0800
GV-POE0810
Third-Party PoE
Switches
(IEEE 802.3at)
Compatibility
1. GV-POEX0100 is only compatible with third-party switches that comply to PoE+ (IEEE
802.3at) and is not compatible with GV-PA191/481/482/901.
2. GV-POEX0100 supports all GV-IP Cameras when installed with a power adapter and
does not support the following models when powered by PoE:
• GV-BX2510-E / 5310-E
• GV-FE3403 / 5303
• GV-VD2540-E / 5340-E
• GV-SD220 / 220-S
3. GV-POEX0100 is only compatible with the following GeoVision PoE switches of the
indicated firmware versions:
• GV-POE0801 / 1601 / 2401 (V1.03 or later)
• GV-POE0811 / 1611 / 2411 (V1.01 or later)
Packing List
1. GV-POEX0100
2. Screw x 2
3. Screw anchor x 2
4. GV-POEX0100 Installation Guide
Note: If any of these items is found missing or damaged, please contact your local supplier
for replacement.
2
June 16, 2016
Loading...