Hardware Installation
1. Connect the receiver’s green mouse
connector to the computer’s 6-pin
PS/2 mouse port. Connect the receiv
er’s purple keyboard connector to
the computer’s 6-pin PS/2 keyboard
port.
2. Install two AA batteries in the mouse
and two AA batteries in the key
board.
3. Turn on your computer.
4. After you open Windows, please press the button under the receiver first (RB)
and then press the button under the mouse (MB) and keyboard (KB) for ID
channel setting. You only have six seconds to press the receiver, the channel
button on the keyboard (KB), then the receiver button again and the channel
button on the mouse (MB). So you press RB, KB, RB, MB to set the channel
setting.
Warning:
1. When you use Wireless TwinTouch+ Optical on a desk that is made of metal, try
using a pad or reduce the receiving distance.
2. Before the first installation is completed (channel setting ready), the keyboard
will not work in DOS.
3. The Wireless TwinTouch+ Optical channel provides 256 ID-codes, and it auto
matically selects the ID # for your keyboard and mouse. You can only set up one
TwinTouch+ Optical at a time. But if you have additional TwinTouch+ Optical
sets in an area of 10 square meters, more interference may occur between the re
ceiver and your keyboard and mouse.
4. If you feel the mouse does not move smooth as usual or the keyboard does not
work when typing, then the batteries have lost their charge, so please replace
them. Also, the wireless icon will be blinking “red” when there is a battery-
low situation. You should set up the channel every time you replace the bat
terires.
-
-
-
ENGLISH
-
-
1
5. The TwinTouch+Optical with radio frequency gives you free movement and an
enjoyable experience. For optimal performance, place the receiver at least 8
inches (about 20 cm) away from the mouse and other electrical devices, such as
the computer, monitor, and etc.
6. Please do not use this optical mouse on a desk which is made of glass, mirror,
iron, or black velvet. Also, a flat surface is necessary or the optical sensor will
not work properly.
Software Installation
1. Make sure the mouse and keyboard is connected to the computer.
2. Put the Setup disk (or CD) into the disk drive.
3. Follow the instructions on the screen to finish the software installation.
Factory Setting
1. Mouse:
Button Assignments
The Button Assignment feature lets you work in a more efficient way because you
can assign the most frequently used commands in Windows to the mouse buttons.
Magic-Roller Press the “Magic-Roller” to surf the Internet and Windows docu
ments
Left Button Provides traditional mouse functions such as click, double click and
drag.
Right Button You can assign this button frequently used keyboard and mouse func
tions in addition to features like EasyJump, Auto-Panning, Zoom, etc.
-
-
2
Roller ButtonYou can assign this button frequently used keyboard and mouse func
tions in addition to features like EasyJump, Auto-Panning, Zoom, etc.
Side Buttons You can assign certain functions (Application/Document, Horizontal
Scrol, Last/Next Page, and Zoom in/out) to the upper or lower side
button with the roller.
2. Keyboard:
1. Rewind: Previous track of audio or video CD’s
2. Play & Pause: Play and pause of audio or video CD’s
3. Stop: Stop play of audio or video CD’s
4. Forward: Next track of audio or video CD’s
5. Vol.-& +: decrease or increase volume
6. My favorite: Open my favorite folder
7. E-mail: Open mail folder
8. Back: See last page when viewing the Internet
9. www: Open browser in Netscape or IE
10. Forward: Go to next page when viewing the Internet
11. Sleep: Turn system into wake up mode
MouseMate Software Features
Browsing Speed You can adjust the browsing
speed when you surf the Internet or Windows documents.
-
ENGLISH
Browsing
Direction
Button Find Automatically positions the cursor on the default button,
Trails This option makes it easier to find the cursor when using
Move the “Magic-Roller” forward and the screen will
browse to the top of the document. Move it in reverse and
the document will go in the opposite direction
usually the OK button, when the dialog box appears on
your screen.
an LCD monitor. This option cannot be used if your
monitor does not support it.
3
Loop When you move the cursor to the top (or bottom) of the
screen, it will automatically move the cursor to the bot
tom (or top) of the screen.
Mouse Speed This function lets you adjust the speed at which the
pointer moves across the screen.
Double Click
Speed
Use this function to set the double click speed of the
mouse.
Swap Left/Right Select this option if you want to have the mouse operate
with the right mouse button as the primary button.
Pointers Folders This lets you change the shape of the cursor.
-
Office Mode Only supports Microsoft Office along with some new ap
plications. Features include zoom, scrolling and Autoscrolling features. It’s similar to Microsoft’s IntelliM
ouse.
Genius Mode Supports all applications that use scrollbars, including Of-
fice, with zoom, Auto-panning, and scrolling functions.
About Click here to open the Genius Homepage “www.genius-
net.com.tw”
Orientation This function lets you set the angle when you move the
mouse upward. It gives you a more comfortable angle
when holding the mouse. This function works best with a
portable trackball.
EasyJump for Windows
EasyJump lets you open eight special functions quickly.
Auto-Panning
Control Panel
Help
Internet Access
Close AP Close the application you are using.
Horizontal Moves the cursor to the horizontal scroll bar.
Vertical Moves the cursor to the vertical scroll bar.
Start Activates the Windows Start menu.
Close AP
Close AP
Start
Horizontal
Vertical
-
-
4
Internet Access This function opens Browser to access the Internet.
Help This opens the Help menu.
Control Panel Opens the mouse control panel.
Auto-Panning Move the mouse, and the document will move in the di
rection you move the mouse.
-
Switch Applications
When the right-button or Magic-Roller is set to “Switch AP”, you can quickly switch
from one open application to another without moving the mouse. To switch to a spe
cific application, press the the right button or the Magic-Roller to select the applica
tion.
-
-
Zoom function for Office and IE Applications
Press the “Ctrl” key and move the “Magic-Roller” forward (or backward) to set the
Zoom In/Out function. You can also use just one hand to Zoom In/Out: set the right
button to be the “Ctrl” function, press the right button and move the “Magic-Roller”
forward (or backward) to enlarge (or decrease) the document window.
Auto-Panning
You can set this function in the Button Assignment menu. Move the mouse, and the
document moves in the direction you just moved.
Uninstall the Software
Follow these instructions to remove the software from your hard disk. In Windows,
click on the Start button, select Programs and move to the mouse software. Then click
on Uninstall software.
Customize the Software
This section shows you how to customize the software. To open the software control
panel, you can double-click on the icon in the task bar or select the “Software” icon
from the program group.
ENGLISH
Close the Software
Click the right button on the taskbar, and select “Close Software” to close the soft
ware.
5
-
Loading...