3. Drill one 9/64” hole at each of these locations for sheet metal screws.
4. Cut opening for the unit.
5. Install unit into air duct using the four sheet metal screws provided.
1. Cut out shaded area of template (#1) or for high heat installations, cut on the dotted line. (#2)
2. Place template on the return path of the HVAC system and trace the hole pattern for the unit and mark centers for mounting sc
TOP
INSTALLATION
#1
(Opening size is 6.75” x 2.5”)
Cut out on dashed line.
(Pa ge In ser t)
G
GUV
ENERAL
TEMPLATE
2018
A
IR
E
rews.
Page 2
TROUBLESHOOTIN
G
• Under normal operation the LED should light when the unit has been supplied power.
If the LED does
1. Check
to be
sure
2. Be sure lamp
light:
not
there is power to the unit.
connector
is fastened
securely
.
3. If the LED still does not light, replace lamp.
4. If still
ARRANT
W
not operating,
Y
replace ballast.
The manufacturer warrants the GUV-161 air purification unit against defects in
materials and workmanship for a period of four (4) years from the date of installation.
Lamps carry a warranty for the useful life of the lamp, two (2) years .
This warranty does not cover broken lamps due to shipping, installation or handling.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
the
packag
care to not t
from the hands can cause “hot spots” which reduce lamp life.
Handle by the porcelain caps or use a soft cloth. If you
accidentally touch a l amp, wipe it o ff using a soft cloth
dampened
proper care must b
ing. Carefully remove lamp f
Be
lamp p laced i n a tube with p rotective
ouch
with
rubbing
sure the following parts are i
• GUV-161 Air Purifier
• 16” Germicidal Lamp (packed in tube
• Four Sheet Metal Screws and two keps n
• Titanium photocatalytic reflecto
• Installation & maintenance instructions
UNIT
THE
is shipped
unit
rom the tube taking
the glass portion with bare hands. Oils
e taken
alcohol.
when it is
lamp is fragile
The
removed from packaging.
ncluded:
with
)
r
and
uts
IMPORTANT SAFETY INSTRUCTIONS
When installing
should always be observed including the following:
1. READ AND
2. SAVE
3.
Always be
4. Ultraviolet light produced
Do not
lamp, use UV-protected safety.
THESE
look directly
and using this electrical
FOLLOW ALL INSTRUCTIONS.
INSTRUCTIONS
sure the unit is unplugged during installation or service procedures.
by
at the lamp.
.
the UV
equipment,
lamp
Should it
is
harmful to your
become
basic safety precautions
eyes.
necessary to view the
Page 4
INSTALLATION
• Best results are achieved when the unit is installed where
air temperature is most constant.
return side of the furnace. If return side installation is
the
unit on the s
possible, and in
• Do not locate the unit within 20” of any plastic material that will b
exposed to the UV
filters. Check with the filter manufacturer to see if their material is UV resistant.
Over time, U
• Do not touch the glass portion of the lamp with bare hands because oils fro
the hands can cause “hot spots” which reduce lamp life. Handle either by the
porcelain caps or use a soft cloth. If you accidentally touch a lamp, wipe it off,
using a soft cloth dampened with rubbing alcohol.
upply
main airstream.
the
light, such
V light will degrade many plastic materials.
Therefore, the preferred installation
side, k
eeping
as a return s
far from the heat/cooling source as
it as
humidifier or certain
ide
1. The ballast is factory set at 120 VAC. For installations that require
240 VAC locate the 120/240 volt power selector on the ballast and
set for the correct voltage. (Photo A)
2. Cut out the shaded area of the installation template.
insert.) Center the template on the longitudinal axis of the plenum
using tape to hold it in place. Trace the hole pattern for the unit
and mark centers for mounting screws.
Drill 9/64” holes for sheet metal screws and cut opening for the unit.
3.
Remove the cover from the unit using a 11/32 size nut driver to remove
4.
the top and bottom retaining nuts and set aside.
5. Attatch the titanium reactor panel to
back of unit as an inverted “V” t
o
maximize airflow (as indicated in
photo A.) Use an 11/32 size nut driver
and
the
8-32 keps nuts packaged w
ith
sheet metal screws and fasten securely.
the HVAC
not
possible,
e
Germicidal
Lamp Holder
install
m
(Photo A)
8-32 keps nuts
(Photo
B)
4. Attach unit to air duct using the four
sheet metal screws provided.
6. Remove germicidal lamp holder
(Figure A)
7.
Slide germicidal lamp into lamp opening
using a 11/32 size nut driver.
8. Reinstall lamp holder.
Plug in lamp connector to the end of lamp.
9.
10. Replace and secure cover using the
two retaining nuts.
.
(Figure A)
Page 5
WIRING
Simply plug
set at
ballast
codes.
the
unit into
or installations that require 240 VAC locate the 120 / 240 volt power selector on th
AC. F
120 V
for the correct voltage. (
and set
an 120 V
AC
outlet and a
Photo A
) R
MAINTENANCE
This maintenance s
will
dictate
the lamp with b
Handle either
using a soft cloth dampened with rubbing alcohol.
the frequency o
chedule is
are hands b
the porcelain caps or
by
only a
f cleaning
ecause oils from the hands can cause “
guideline, d
and/or replacement
a soft cloth. If you accidentally touch a lamp, wipe it off,
use
llow
emove
etermined by average conditions. Actual conditions
run
it to
plug and wire
of lamps. Do
continuousl
hot
in
spots” which reduce lamp life.
y. The
accordance w
not touch the
ballast is
ith
l
glass portion of
ocal w
factory
irin
e
g
CLEANING THE LAMP -
1. Unplug the
2. Remove
bottom retaining nuts.
3. Unplug the
4. Remove lamp holder using a 11/32 size nut driver.
5. Remove the
Using a soft cloth moistened with
6.
of dust particles, you may want to use a can of a
7. Slide the lamp back into lamp opening.
8. Reinstall lamp holder.
9. Plug the lamp connector to the end of
10. Replace and secure cover using the two retaining
11. Plug power cord back into outlet, or restore power to unit.
power
the
cover
lamp connector from
lamp b
from
cord
from
y grasping the porcelain cap and extract carefully.
the outlet, or disconnect power to
the unit using a 1
rubbing alcohol, wipe down the lamp. If there is a large build-up
Recommended interval: 12 months
1/32 s
ize nut driver to r
the end of the lamp.
(Figur
e
ir first. Always handle lamp by the end caps.
lamp.
the
nuts.
B)
the
unit.
emove t
he
top
and
REPLACING THE LAMP -
Recommended interval: 24 months.
Follow above procedure excluding #6.
Please note standard off-the-shelf lamps are not compatible with this unit.
Use of improper lamps will void warranty.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.