Generac 6599, 6598, 6595, 6597 User Manual

Operator's Manual

Power Washer

www.generac.com or 1-888-436-3722

Introduction ............................................................. 1

Safety Rules ...........................................................1

Safety Symbols and Meanings .......................................1

General Information ................................................ 4

Know Your Power Washer .........................................................4

Product Specifications ..............................................................5

Emissions Information ..............................................................5

High Altitude Operation ..............................................................5

Unpacking .................................................................................6

Set-up ..................................................................... 6

Assembly ..................................................................................6

Add Engine Oil ..........................................................................7

Add Fuel ...................................................................................7

Connect Hose and Water Supply to Pump .................................8

How to Use Nozzles ..................................................................9

Cleaning and Applying Detergent ..................................10

Power Washer Rinsing .................................................11

Cleaning Detergent Siphoning Tube ...............................11

Operation .............................................................. 12

Operation ................................................................................12

Power Washer Location ..........................................................12

Checklist Before Starting Engine ..............................................12

How to Start Your Power Washer ............................................12

Automatic Cool Down System (Thermal Relief) .......................14

How to Stop Your Power Washer .............................................14

Maintenance ......................................................... 14

Maintenance Recommendations ..............................................14

Maintenance Schedule ............................................................15

Pump Oil .................................................................................15

Emissions Control ...................................................................15

Power Washer Maintenance ....................................................15

Check and Clean Inlet Screen ..................................................15

Check High Pressure Hoses ....................................................15

Check Detergent Siphoning Tube .............................................15

Check Spray Gun ....................................................................15

Nozzle Maintenance ................................................................15

Engine Maintenance ................................................................16

Engine Oil Recommendations ..................................................16

Check Oil Level ............................................................17

Adding Engine Oil .........................................................17

Changing Engine Oil .....................................................17

Service Air Cleaner .................................................................18

Service Spark Plug ..................................................................18

Inspect Muffler and Spark Arrestor ..........................................18

Remove Spark Arrester Screen .....................................18

After Each Use ........................................................................19

Winter Storage ........................................................................19

Long Term Storage..................................................................20

Protect Fuel System .....................................................20

Protect Engine ..............................................................20

Change Oil ...................................................................20

Protecting the Pump .....................................................20

Other Storage Instructions .......................................................20

Transporting/Tipping of the Unit ..............................................20

Troubleshooting .................................................... 21

Troubleshooting Guide .............................................................21

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

Introduction

INTRODUCTION

Thank you for purchasing this power washer manufactured by Generac Power Systems, Inc. This model is a high performance, air-cooled, engine-driven power washer that operates between 2500 and 3100 psi depending on which model you purchased. The units feature custom designed wheels, axial cam pump with stainless steel pistons, automatic cool down system, quick connect nozzles, high pressure hose, detergent siphoning hose and chemical tank(s) depending on unit model.

Common sense and strict compliance with the special instructions are essential to preventing accidents. The operator must read

this manual and thoroughly understand all of the instructions and warnings before using the equipment. If any portion of the manual is not understood, contact the nearest Authorized Dealer for starting, operating and servicing procedures. The owner is responsible for proper and safe use of the equipment.

The power washer can operate safely, efficiently and reliably only if it is properly located, operated and maintained. Before operating, servicing or storing:

• Study all warnings in this manual and on the product carefully.

• Become familiar with this manual and the unit before use.

• Refer to the Assembly section of the manual for instructions on final assembly procedures. Follow the instructions completely.

The manufacturer cannot anticipate every possible circumstance that might involve a hazard. The warnings in this manual, and on tags and decals affixed to the unit are, therefore, not all inclusive. If using a procedure, work method or operating technique that the manufacturer does not specifically recommend, ensure that it is safe for others. Also make sure the procedure, work method or operating technique utilized does not render the power washer unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION. GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT ANY TIME.

Save these instructions for future reference. If you loan this device to someone, ALWAYS loan these instructions AND the Owner's Manual to the individual as well.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the power washer, DANGER, WARNING, CAUTION and NOTE blocks are used to alert personnel to special instructions about a particular operation that may be hazardous if performed incorrectly or carelessly. Observe them carefully. Their definitions are as follows:

Indicates a hazardous situation or action which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they indicate. Common sense and strict compliance with the special instructions while performing the action or service are essential to preventing accidents.

SAFETY SYMBOLS AND MEANINGS

Hearing Protection

KickbackToxic Fumes Electrical Shock

WHERE TO FIND US

You can contact Generac Customer Service by phone at 1-888436-3722, or on the internet at www.generac.com. Record the important information of the unit in the following chart for future reference and/or service inquiries.

Model Number Serial Number Date Purchased

Fluid InjectionFall

Slippery Surface

Fire Explosion Operator’s Manual

Moving Parts Flying Objects Hot Surface

Fluid InjectionFall

Safety Rules

WARNING: Hearing Protection Recommended.



DANGER: NEVER aim spray gun at people, animals, or



electrical devices. Serious injury or death will result. ALWAYS point spray gun in safe direction, squeeze spray gun trigger to release high pressure, every time you stop engine. Engage trigger lock when not in use.

• The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury, possible amputation or death. Spray gun traps high water pressure, EVEN WHEN engine is stopped and water is disconnected, which can cause injury.

• NEVER allow CHILDREN to operate power washer or play nearby. This is NOT a toy.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• NEVER secure spray gun in open position.

• NEVER leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order.

• ALWAYS be certain spray gun, nozzles and accessories are correctly attached.

WARNING: Risk of electrocution.



Contact with power source can cause electric shock or burn.

• NEVER spray near power source.

WARNING: Contact with muffler area can result in serious burns. Exhaust heat/gases can ignite combustibles,



structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least five (5) feet (152 cm) of clearance on all sides of power washer including overhead.

• It is a violation of California Public Resource Code, Section 4442, to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust system is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order. Other states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed on this engine.

• Replacement parts must be the same and installed in the same position as the original parts.

WARNING: Fuel and its vapors are extremely flammable and

explosive. Fire or explosion can cause severe burns or death.



WHEN ADDING OR DRAINING FUEL

• Turn power washer OFF and let it cool at least two (2) minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers, or other appliances that have pilot light or other ignition source because they can ignite fuel vapors.

WARNING: Use of power washer can create puddles and slippery surfaces. Kickback from spray gun can cause you to



fall.

• Use only on a level surface.

• The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces.

• Do not use on elevated surfaces where chance of kickback could result in a serious fall.

• Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

WARNING: Starter and other rotating parts can



entangle hands, hair, clothing, or accessories.

• NEVER operate power washer without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

WARNING: Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward



engine faster than you can let go. Broken bones, fractures, bruises, or sprains could result.

• NEVER pull starter cord without first relieving spray gun pressure.

• To relieve trapped pressure, point gun in safe direction and release pressure by pulling/actuating trigger on spray gun.

• When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always point spray gun in safe direction, and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

Safety Rules

NOTE:

High pressure spray may damage fragile items including glass.

• DO NOT point spray gun at glass when using red (0°) MAX nozzle.

• NEVER aim spray gun at people, animals, electrical devices or plants.

NOTE:

Improper treatment of power washer can damage it and shorten its life.

• If you have questions about intended use, ask dealer or contact qualified service center.

• NEVER operate units with broken or missing parts, or without protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT operate power washer above rated pressure.

• DO NOT modify power washer in any way.

• Before starting power washer in cold weather, check all parts of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided on unit.

• Check fuel system for leaks or signs of deterioration, such as chafed or spongy hose, loose or missing clamps, or damaged tank or cap. Correct all defects before operating power washer.

• This equipment is designed to be used with Generac authorized parts ONLY. If equipment is used with parts that DO NOT comply with minimum specifications, user assumes all risks and liabilities.

WARNING: Unintentional sparking can result in fire or electric shock.



WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER WASHER.

• Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING: Risk of eye injury. Spray can splash back or

propel objects.



• Always wear safety goggles when using this equipment or in vicinity of where equipment is in use.

• Before starting the power washer, be sure you are wearing adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

General Information

KNOW YOUR POWER WASHER

Read this owner’s manual and safety rules before operating your high power washer.

If you loan this device to someone, ALWAYS loan these instructions AND the owner’s manual to the individual as well. Compare the illustrations with your high power washer to familiarize yourself with the locations of various controls (Figure 1). Save this manual for future reference. Replacement owner’s manuals can be printed from the Generac Web site.

A - Spray Gun – Controls the application of water onto the cleaning

surface with trigger device. Includes a trigger lock.

B - Lance with Quick Connect – Allows you to switch between different

nozzles.

C - High Pressure Hose – Connect one end to water pump and the other

to the spray gun.

D - Recoil Starter – Use for starting the engine. E - Oil Fill – Check and add engine oil. F - Air Filter – Protects engine by filtering dust and debris out of the

intake air.

G - Pump – Develops high pressure. H - Thermal Relief Valve – Cycles water through the pump when water

reaches 125 °F warm water will discharge from pump onto ground. This prevents internal pump damage.

I - Engine On/Off Switch – Turn this switch to “ON” before using the

recoil starter. Turn the switch to “OFF” to stop the engine.

J - Unloader Valve – Controls the high pressure output. K - High Pressure Outlet – Connection for high pressure hose. L - Water Inlet – Connection for Garden Hose. M - Fuel Tank – Fill tank with regular unleaded fuel. Always leave room

for fuel expansion.

N - Fuel On/Off Switch – Turns fuel supply to the engine on and off. O - Choke – Prepares a cold engine for starting. P - Nozzles – Chemical injection, 0°, 15°, 25°, 40° for various high

pressure cleaning applications.

Q - Chemical Tank – Used to hold power washer safe detergents to

be siphoned into the low pressure stream. (some units may not be equipped with tanks or may only have one tank).

R - Warning/Operation Instruction – Identifies proper procedure to

start/stop power washer.

S - Drain Plug – Used to drain engine oil. T - Serial Number Location

ITEMS NOT SHOWN

• Identification Label (on engine blower housing) – Provides model and serial number of power washer. Please have these readily available if calling for assistance.

• Detergent Siphoning Tube/Filter – Use to siphon power washer safe detergents into the low pressure stream.

Figure 1 – Features & Controls

General Information

PRODUCT SPECIFICATIONS

CONSUMER

Pressure - (PSI / BAR) 2500/172 Max 2800/193 Max 3100/213 Max Flow Rate - (GPM / LPM) 2.3/8.7 Max 2.5/9.5 Max 2.7/10.2 Max Water supply temperature - (°F / °C) 100/38 Max Hose length - (Feet / Meters) 25/7.6 25/7.6 30/9.1 Chemical Tank(s) - Number per unit 0 1 2 Chemical Tank - Capacity (Gallon - Liters) N/A 0.75/2.8 0.75/2.8 Nozzles - Number per unit 3 4 5 Lance Length (Inches / cm) 20/51 Gun Standard Deluxe Engine Displacement - (Cubic Inch / cc) 11.9/196 12.9/212 Spark Plug Type F7TC or equivalent Spark Plug Gap - (Inches / mm) 0.028-0.031/0.70-0.80 Fuel Capacity - (Quarts / Liters) 3.7/3.5 Oil Capacity - (Oz / Liters) 20/0.6 Low Oil Shut Down System No On/Off Switch Yes

EMISSIONS INFORMATION

The U.S. Environmental Protection Agency (and California Air Resource Board for equipment certified to CA standards) requires that this engine comply with exhaust and evaporative emission standards. Locate the emissions compliance decal on the engine to determine what standards the engine meets, and to determine which emissions warranty applies. The engine is certified to meet the applicable emission standards on gasoline. It is important to follow the maintenance specifications in the Maintenance section to ensure that the engine complies with the applicable emission standards for the duration of the product’s life. This engine utilizes lean carburetion settings and other systems to reduce emissions. Tampering with or altering the emission control system may increase emissions and may be a violation of Federal or California Law. Acts that constitute tampering include but are not limited to:

• Removal or alteration of any part of the intake, fuel, or exhaust systems

• Altering or defeating the governor linkage or speed-adjusting mechanism to cause the engine to operate outside its design parameters

If you are aware of any of the following symptoms, have your engine inspected and repaired by your servicing dealer:

• Hard starting or stalling after starting

• Rough idle

• Misfiring or backfiring under load

• Afterburning (backfiring)

• Black exhaust smoke or high fuel consumption

HIGH ALTITUDE OPERATION

The fuel system on this engine may be influenced by operation at higher altitudes. Proper operation can be ensured by installing an altitude kit when required. See the table below to determine when an altitude kit is required. Operating this engine without the proper altitude kit installed may increase the engine’s emissions and decrease fuel economy and performance. Kits may be obtained from any Dealer, and should be installed by a qualified individual.

Altitude* Kit Number PSI

0 - 5000 Feet Not Required 2500/2800/3100 5000 - 7000 Feet 0K2015 2500/2800 5000 - 7000 Feet 0K2016 3100

*Elevation above sea level.

NOTE:

If the altitude kit has been installed and the engine will be operated at an altitude where the kit is not required, the engine should be returned to the original factory configuration. Operating the engine at lower altitudes with the kit installed may cause the engine to overheat and result in serious engine damage, and may result in decreased performance and increased emissions.

Set-up

UNPACKING

1. Remove the parts bag, accessories, and inserts included with power washer.

2. Open carton completely by cutting each corner from top to bottom.

3. Ensure you have all included items prior to assembly.

• Main Unit

• Handle Assembly

• High Pressure Hose

• Siphon Hose & Filter

• Spray Gun

• Lance with Quick Connect Fitting

• Oil Bottle

• Hose Hook Wireform

• Parts Bag (which includes the following): – Chemical Tank Cap with hole if model is equipped with a

Chemical Tank – Operator’s Manual – Owner’s Registration Card – Bag containing Color-coded Nozzles

4. If you are missing any items from your carton, please call Generac Customer Service at 1-888-436-3722. When calling for assistance, please have the model and serial number from the data tag available.

5. Fill out and send in registration card. Write Model number, Serial number & date of purchase in the table located in the "Where to Find Us" section.

ASSEMBLY

Read entire operator’s manual before you attempt to assemble or If you have any problems with the assembly of your power washer, please call Generac Customer Service at 1-888-436-3722. When calling for assistance, please have the model and serial number from the data tag available.

1. Place handle (A) onto handle supports (B). Push in latch buttons and allow handle to slide into position (C). Button will lock handle into place (Figure 2).

NOTE:

It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports.

2. Install hose hook (Figure 3).

Figure 3 – Install Hose Hook

3. Insert color–colored nozzles in spaces provided in handle (Figure 4).

4. Place spray gun and nozzle extension into spray gun holder as shown (Figure 4).

5. Coil high pressure hose and hang on hook.

Figure 4 – Insert Nozzles

Figure 2 – Attach Handle

Set-up

6. Attach siphon tube to location A (Figure 5).

Figure 5 – Siphon Tube Location

ADD ENGINE OIL

1. Make sure the power washer on a level surface.

2. Clean area around oil fill.

3. Remove oil fill cap and wipe dipstick clean.

4. Using oil funnel, slowly pour oil into fill opening. See Maintenance section for oil type recommendation.

NOTE:

On some units there is more than one oil fill location. In these instances it is only necessary to use one of the oil fill points.

5. Check periodically until the oil level is between "L" and "H" on the dipstick (Figure 6). Insert dipstick into filler neck but do not screw in.

6. Verify oil is at the proper level on the dipstick.

Figure 6 – Dipstick

ADD FUEL

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTE:

Avoid power washer damage. Failure to follow Operator’s Manual for fuel recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels. To protect the fuel system from gelling, mix in a fuel stabilizer when

adding fuel. See Storage. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands.

Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

• Turn power washer OFF and let it cool at least two (2) minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful not to overfill. Fill to bottom of filter screen, this will allow for fuel expansion (Figure 7).

3. Install fuel cap and let any spilled fuel evaporate before starting engine.

7. Replace and tighten oil fill cap/dipstick.

Figure 7 – Adding Fuel

Acceptable Oil Level Range

Set-up

CONNECT HOSE AND WATER SUPPLY TO PUMP

NOTE:

DO NOT run the pump without the water supply connected and turned on. Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE:

Remove and discard the shipping cap from the pump’s water inlet before attaching hose.

1. Run water through your garden hose for 30 seconds to clean out any debris.

2. Before connecting garden hose to water inlet, inspect inlet screen (A) (Figure 8). Clean screen if it contains debris or have it replaced if damaged. DO NOT run power washer if inlet screen is damaged.

IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F). Water supply must be adequate to handle greater than 3.8 gallons per minute and no less than 30 psi.

NOTE:

Using a One Way Valve (vacuum breaker or check valve) at pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose between the power washer inlet and any device, such as a vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this instruction will void warranty.

Figure 9 – Connect Garden Hose

Risk of eye injury. Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

4. Connect lance to spray gun (Figure 10). Tighten by hand.

Figure 10 – Attach Lance

Figure 8 – Inspect Inlet Screen

3. Connect the garden hose (not to exceed 50 feet in length) to the water inlet (Figure 9). Tighten by hand.

5. Attach end of high pressure hose to base of spray gun (Figure

11). Tighten by hand.

Figure 11 – Connect Hose to Spray Gun

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

• NEVER connect high pressure hose to lance.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• Always be certain spray gun, nozzles and accessories are correctly attached.

6. Connect high pressure hose to pump (uncoil hose before connecting to pump or spray gun) (Figure 12). Tighten by hand.

The hose can be damaged if it comes in contact with a



hot engine or muffler.

Figure 12 – Connect High Pressure Hose to Pump

Set-up

HOW TO USE NOZZLES

The quick–connect on the nozzle lance allows you to switch between different nozzles. Nozzles can be changed while power washer is running once spray gun trigger is locked in the safety position. The nozzles vary the pressure and spray pattern as shown.

• For most effective cleaning, keep nozzle from 8 to 24 inches (20 to 61 cm) away from cleaning surface.

• If you get nozzle too close, especially using a high pressure nozzle, you may damage surface being cleaned.

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

• NEVER exchange nozzles without the trigger lock being engaged on the spray gun.

• DO NOT twist nozzles while spraying.

UNIT RATED NOZZLE PSI GPM

2500 Blast/Wash 2500 2.3

2800

3100 Blast/Wash 3100 2.7

Blast 2800 2.4

Wash 2600 2.5

7. Turn ON the water, squeeze the trigger to purge the pump system of air (Figure 13).

Figure 13 – Squeeze Trigger

Follow these instructions to change nozzles:

1. Pull back collar on quick–connect and pull current nozzles off. Store nozzles in holder provided on the accessory storage (Figure 14).

Figure 14 – Nozzles

2. Select desired nozzle.

3. Pull back on collar, insert new nozzle and release collar. Tug on nozzle to make sure it is securely in place.

Set-up

• For delicate rinse (lower pressure and higher flow), for gentle cleaning of cars/trucks, boats, RV’s, patio furniture, lawn equipment, etc., select white nozzle (Figure 15).

Figure 15 – Wash Pressure Nozzle (White)

• For general rinsing (medium pressure and medium flow), ideal for most all purpose cleaning such as home siding, brick patios, wood decks, driveways and sidewalks, garage floors, etc., select green nozzle (Figure 16).

Figure 16 – Clean Pressure Nozzle (Green)

• For maximum rinsing (higher pressure and lower flow), for stubborn or hard to reach surface such as second story surfaces, paint removal, oil stains, rust removal or other stubborn substances (tar, gum, grease, wax, etc.), select red nozzle (Figure 18).

This tip (Red Nozzle) can damage work surface if it is too close or held in one position for an extended time.



Figure 18 – Blast Pressure Nozzle (Red)

• When applying detergent, use only the black nozzle (Figure 19). Only use power washer safe detergents/soaps to help break down stubborn dirt and grime on a variety of surfaces.

• For medium rinsing (higher pressure and medium flow), ideal for removing stains on hard porous surfaces such as concrete dirveways, garage floors and brick patios, select yellow nozzle (Figure 17).

Figure 17 – Strip Pressure Nozzle (Yellow)

Figure 19 – Detergent Nozzle (Black)

CLEANING AND APPLYING DETERGENT

Chemicals can cause bodily injury, and/or property damage.



• NEVER use caustic liquid with power washer.

• Use ONLY power washer safe detergents/soaps. Follow all manufacturer's instructions.

To apply detergent, follow these steps:

1. Review use of nozzles.

2. Open container cap (if so equipped, Figure 20).

3. Prepare detergent solution as required by job.

Operation

Figure 20 – Chemical Tank & Cover

Container

Cap

4. Depending on model, insert filter on end of siphoning tube through the hole in the loose cap (supplied) (Figure 21).

5. Install cap and siphoning tube onto tank.

6. Make sure siphoning tube remains fully submerged into detergent.

Figure 21 – Install Siphoning Tube

• Damage to equipment resulting from failure to follow this instruction will void warranty.

9. Start engine following instructions How to Start Your Power Washer.

10. Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward using long, even, overlapping strokes.

11. Allow detergent to "soak in" for 3-5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on surface being cleaned (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after each use by placing the filter into a bucket of clean water, then run the power washer in low pressure for 1-2 minutes.

POWER WASHER RINSING

1. Remove black detergent nozzle from lance.

2. Select and install desired high pressure nozzle following instructions How to Use Nozzles.

3. Point spray gun in safe direction and away from people, animals and plants. Squeeze trigger to flush any remaining chemical from system.

4. Keep spray gun a safe distance from area you plan to spray.

NOTE:

Make sure the filter remains fully submerged in detergent while applying detergent.

NOTE:

Contact with the hot muffler can damage detergent siphoning tube.

• When inserting the siphon into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler.

7. Make sure black detergent nozzle is installed.

NOTE:

Detergent cannot be applied with the high pressure nozzle (Yellow, White, Green or Red). Only use the Black nozzle with detergent.

8. Confirm set-up instructions have been followed.

NOTE:

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without the water turned ON will damage the pump.

Kickback from spray gun can cause you to fall.

• Use only on a level surface.

• Do not use on elevated surface to prevent the risk of a serious fall.

• Be extremely careful if you must use the power washer from a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

5. Apply a high pressure spray to a small area and then check surface for damage. If no damage is found, you can assume it is okay to continue rinsing.

6. Start at top of area to be rinsed, working down with same overlapping strokes as you used for cleaning.

CLEANING DETERGENT SIPHONING TUBE

If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of clean water.

2. Remove high pressure nozzle from nozzle extension.

3. Select and install black detergent nozzle following instructions How to Use Nozzles.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop Power Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to release retained high water pressure. Engage trigger lock when not in use.

Operation

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation. Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction, and squeeze spray gun trigger to release high pressure, every time you stop engine. Engage trigger lock when not in use.

OPERATION

If you have any problems operating your power washer, please call Generac customer service at 1-888-436-3722.

POWER WASHER LOCATION

Clearances and Air Movement

Running engine gives off carbon monoxide, an odorless, colorless, poisonous gas. Breathing carbon monoxide can cause headache, fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death. For more information, reference the CO warnings in the Safety Rules section.

Figure 22 – Building Clearances

5 Foot Minimum

CHECKLIST BEFORE STARTING ENGINE

1. Be sure to read and understand the Operator Safety section and Operation section before using power washer.

2. Check that oil is at the proper level in the engine crankcase and that fuel has been added to the fuel tank.

3. Review the unit's assembly and ensure fitting are properly secured and make sure there are no kinks, cuts, or damage to high pressure hose.

4. Provide a proper water supply at an adequate flow, clear screens of debris, and confirm that the system is purged of air.

5. Confirm unit is secure on level ground and surrounding work area is clear.

Place power washer outdoors in an area that will not accumulate deadly exhaust gas. NEVER place power washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept away from any windows, doors, ventilation intakes, or other openings that can allow exhaust gas to collect in a confined area. Prevailing winds and air currents should be taken into consideration when positioning power washer (Figure 22).

• Operate power washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes, or other openings.

• NEVER start or run engine indoors, in a vehicle or in an enclosed area, EVEN IF windows and doors are open.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of power washer including overhead.

HOW TO START YOUR POWER WASHER

NOTE:

DO NOT run the pump without the water supply connected and turned on. Damage to equipment resulting from failure to follow this instruction will void warranty.

1. Move the fuel valve lever to the ON position (Figure 23).

Figure 23 – Fuel Valve

Off

Operation

2. Move choke lever to “CLOSE” position (Figure 24).

NOTE:

For a warm engine, be sure the choke lever is in the “OPEN” position.

Figure 24 – Choke Lever

Choke

Open

3. Turn the engine switch to the "ON" position (Figure 25).

Figure 25 – The ON Position

OFF

Figure 26 – Starting the Engine

Starter Handle

Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises, or sprains could result.

• NEVER pull starter cord without first relieving spray gun pressure.

• When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always point spray gun in safe direction and squeeze spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when spray gun kicks back.

6. Return starter grip handle slowly. DO NOT let rope “snap back” against starter.

7. When engine starts, slowly move choke lever to “OPEN” position as engine warms. If engine falters, move choke lever to “CLOSE” position, then to “OPEN” position (Figure 27).

IMPORTANT: Before starting the power washer, be sure you are wearing adequate safety goggles.

Risk of eye injury. Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

4. Place foot on footpad or otherwise secure unit from movement when pulling recoil.

5. When starting the engine, grasp starter grip handle (Figure

26) and pull slowly until you feel some resistance. Then pull rapidly to start engine.

Figure 27 – Choke Lever

Choke Open

8. After each starting attempt, where engine fails to run, always point gun in safe direction, and squeeze spray gun trigger to release high pressure.

9. If engine fails to start after six pulls, move choke lever to “OPEN” position, and repeat steps 6 through 9.

Maintenance

• DO NOT allow CHILDREN to operate power washer or play nearby.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• NEVER aim spray gun at people, animals or electrical devices. Serious injury will result.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are correctly attached.

 Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite combustibles, structures or damage fuel tank

causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of power washer including overhead.

• Replacement parts must be the same and installed in the same position as the original parts.

AUTOMATIC COOL DOWN SYSTEM (THERMAL RELIEF)

If you run the engine on your power washer for 3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F. The system engages to cool the pump by discharging the warm water onto

the ground.

HOW TO STOP YOUR POWER WASHER

1. Release spray gun trigger.

2. Turn the engine ON/OFF switch to the "OFF" position.

3. ALWAYS point spray gun in a safe direction, and squeeze spray gun trigger to release retained high water pressure. Engage trigger lock when not in use.

4. Turn OFF water supply.

IMPORTANT: Spray gun traps high water pressure, even when engine is stopped and water is disconnected.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze spray gun trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

MAINTENANCE RECOMMENDATIONS

Regular maintenance will improve the performance and extend the life of the power washer. See any qualified dealer for service.

The power washer’s warranty does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the power washer as instructed in this manual, including proper storage as detailed in Winter Storage and Long Term Storage.

NOTE:

Should you have questions about replacing components on your power washer, please call 1-888-436-3722 for assistance.

Some adjustments will need to be made periodically to properly maintain your power washer.

All service and adjustments should be made at least once each season. Follow the requirements in the Maintenance Schedule chart.

NOTE:

Once a year you should clean or replace the spark plug, clean or replace the air filter, and check the spray gun and nozzle extension assembly for wear. A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer.

Maintenance

MAINTENANCE SCHEDULE

Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse conditions.

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check/clean water inlet screen* Check high pressure hose Check detergent siphoning hose/filter Check spray gun and assembly for leaks Clean debris Check engine oil level

Every 20 Hours or Every Season

Change engine oil**

Every 50 Hours or Every Season

Check/clean air cleaner filter** Inspect muffler and spark arrester*

Every 100 Hours or Every Season

Service spark plug

* Clean if clogged. Replace if perforated or torn. ** Service more often under dirty or dusty conditions.

PUMP OIL

DO NOT attempt any oil maintenance on this pump. The pump is pre-lubricated and sealed from the factory, requiring no additional maintenance for the life of the pump.

EMISSIONS CONTROL

Maintenance, replacement, or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or individual. However, to obtain ”no

charge” emissions control service, the work must be performed by a factory authorized dealer. See the Emissions Warranty.

POWER WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from cleaning system. Keep linkage, spring and controls clean. Keep area around and behind muffler free from any combustible debris. Inspect cooling air slots and openings on the power washer. These openings must be kept clean and unobstructed.

Power washer parts should be kept clean to reduce the risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTE:

Improper treatment of power washer can damage it and shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

CHECK AND CLEAN INLET SCREEN

Examine the screen on the pump’s water inlet. Clean it if the screen is clogged or replace it if screen is damaged.

CHECK HIGH PRESSURE HOSES

The high pressure hoses can develop leaks from wear, kinking, or abuse. Inspect the hoses each time before using them. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST meet or exceed maximum pressure rating of unit.

CHECK DETERGENT SIPHONING TUBE

Examine the filter on the detergent tube and clean if clogged. The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it is secure. Test the trigger by pressing the trigger, it “springs back” into place when you release it. Replace spray gun immediately if it fails to "spring back".

NOZZLE MAINTENANCE

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean the nozzle following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to release retained high water pressure.

SA E 30 *

10 W- 30 **

5W -3 0

Maintenance

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

• ALWAYS point spray gun in safe direction, and squeeze spray gun trigger to release high pressure every time you stop engine. Engage trigger lock when not in use.

3. Remove nozzle from end of nozzle extension.

4. Use a small paper clip to free any foreign material clogging or restricting nozzle (Figure 28).

Figure 28 – Free Foreign Material

5. Remove lance from spray gun.

6. Using a garden hose, remove additional debris by back flushing water through lance (Figure 29). Back flush between 30 to 60 seconds.

7. Reinstall nozzle into lance.

8. Reconnect lance to spray gun.

Figure 29 – Back Flush Lance

ENGINE MAINTENANCE

 Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER WASHER

• Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

ENGINE OIL RECOMMENDATIONS

We recommend the use of high-quality detergent oils acceptable if classified for service SF, SG, SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to select the best viscosity for the outdoor temperature range expected.

SAE 30*

10W-30**

5W-30

9. Make sure garden hose is connected to pump water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

10. Start engine following instructions How to Start Your Power Washer.

11. Test power washer by operating with each quick connect nozzle.

* Below 50°F (10°C) the use of SAE 30 will result in hard starting. ** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.

Check oil level more frequently.

NOTE:

Synthetic oil meeting ILSAC GF-2, API certification mark and API service symbol with “SJ/CF ENERGY CONSERVING” or higher, is an acceptable oil at all temperatures. Use of synthetic oil does not alter required oil change intervals.

NOTE:

The engine is equipped with an "Oil Alert System". This system will automatically stop the engine before the oil level falls below a safe limit. To avoid the inconvenience of an unexpected shutdown, always check the engine oil level before startup.

Maintenance

CHECK OIL LEVEL

Oil level should be checked prior to each use or at least every 8 hours of operation. Keep oil level maintained.

1. Make sure power washer is on a level surface.

2. Clean area around oil fill.

3. Remove oil fill cap and wipe dipstick clean (Figure 30).

4. Insert dipstick into filler neck but do not screw it in.

5. Verify oil is at the proper level on the dipstick.

6. Replace and tighten oil fill cap.

Figure 30 – Fill Engine Oil

ADDING ENGINE OIL

1. Make sure power washer is on a flat, level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening until the proper level on the dipstick is reached.

4. Insert the dipstick into filler neck but do not screw it in.

5. If level is low, fill until the oil level is between "L" and "H" on the dipstick (Figure 31).

6. Replace and tighten oil fill cap.

CHANGING ENGINE OIL

If you are using your power washer under extremely dirty or dusty conditions, or in extremely hot weather, change the oil more often.

Avoid prolonged or repeated skin contact with used motor oil.



• Used motor oil has been shown to cause skin cancer in certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN.



• Don’t pollute. Conserve resources. Return used oil to collection centers.

Change oil while engine is still warm from running, as follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug.

3. Clean area around oil drain plug (A) (Figure 32). The oil drain plug is located at base of engine, opposite carburetor.

4. Remove oil fill cap (Figure 30).

5. Remove oil drain plug and drain oil completely into a suitable container.

6. Reinstall oil drain plug and tighten securely.

7. Slowly pour oil into oil fill opening until the oil level is between "L" and "H" on the dipstick. DO NOT overfill.

8. Reinstall oil fill cap. Finger tighten cap securely.

9. Wipe up any spilled oil.

10. Properly dispose of oil in an accordance with all local regulations.

Figure 32 – Oil Drain Plug

Figure 31 – Dipstick

Acceptable Oil Level Range

0.028-0.031

Maintenance

SERVICE AIR CLEANER

Your engine will not run properly and may be damaged if you run it with a dirty air cleaner. Service more often if operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Pull on air cleaner cover latch and remove cover (Figure 33).

2. Remove filter.

3. To clean filter, gently tap on a flat surface.

4. Reinstall clean or new filter.

5. Install cover by snapping latch closed.

Figure 33 – Service the Air Cleaner

AIR COVER

FOAM ELEMENT

AIR BOX

Figure 34 – Change the Spark Plug

SPARK PLUG

INSPECT MUFFLER AND SPARK ARRESTER

Inspect the muffler for cracks, corrosion, or other damage. Remove the spark arrester, if equipped, and inspect for damage or carbon blockage. If replacement parts are required, make sure to use only original equipment replacement parts.

REMOVE SPARK ARRESTER SCREEN

Tools Required: 8mm Box Wrench

1. Remove heat shield from the muffler by loosening the four (4) Bolts (A) (Figure 35).

2. Remove the spark arrester from the muffler by loosning the two (2) Bolts (B) (Figure 36).

3. Inspect the spark arrester, replace if torn, perforated or otherwise damaged (part number 0K1851). DO NOT USE A DEFECTIVE SCREEN.

4. If screen is not damaged, clean it with a commercial solvent and replace.

SERVICE SPARK PLUG

Changing the spark plug will help your engine to start easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug (Figure 34).

3. Check electrode gap with wire feeler gauge and reset spark plug gap to recommended gap if necessary (see Specifications).

4. Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use the recommended replacement plug. See Specifications.

5. Install spark plug and tighten firmly.

Figure 35 – Remove Heat Shield

Maintenance

Figure 36 – Remove Spark Arrester

 Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of power washer including overhead.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed on this engine.

• Replacement parts must be the same and installed in the same position as the original parts.

AFTER EACH USE

Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and freeze pump action. Follow these procedures after every use:

1. Shut off engine, turn off water supply, point gun in a safe direction, and squeeze trigger to relieve trapped pressure, and let engine cool.

• ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to release high pressure, every time you stop engine. Engage trigger lock when not in use.

2. Disconnect hoses from spray gun and high pressure outlet on pump. Drain water from hoses, spray gun, and lance. Use a rag to wipe off the hose.

3. Empty pump of all pumped liquids. Check that the engine ON/ OFF switch and fuel valve are in the OFF position. Then pull the recoil handle about six times. This should remove most liquid in pump.

4. Store unit in a clean, dry area.

5. If storing for more than 30 days, see the Long Term Storage section.

 Fuel and its vapors are extremely flammable

and explosive. Fire or explosion can cause severe burns or death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers, or other appliances that have pilot light or other ignition source because they can ignite fuel vapors.

WINTER STORAGE

NOTE:

You must protect your unit from freezing temperatures.

• Failure to do so will permanently damage your pump and render your unit inoperable.

• Freeze damage is not covered under warranty.

To protect the unit from freezing temperatures:

1. Follow steps 1-3 in the previous section After Each Use.

2. Use pump saver to treat pump. This minimizes freeze damage and lubricates pistons and seals.

3. If pump saver is not available, connect a 3-foot section of garden hose to water inlet adapter. Pour RV-antifreeze (antifreeze without alcohol) into hose. Pull recoil handle twice. Disconnect 3-foot hose.

4. Store unit in a clean, dry area.

• Keep high pressure hose connected to pump and spray gun while system is pressurized.

Maintenance

LONG TERM STORAGE

If you do not plan to use the power washer for more than 30 days, you must prepare the engine and pump for long term storage.

PROTECT FUEL SYSTEM

Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use a fuel stabilizer, available as a liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel stabilizer is added according to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel system. The engine and fuel can then be stored up to 24 months.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into an approved container. Run the engine until it stops from lack of fuel. The use of a fuel stabilizer in the storage container is recommended to maintain freshness.

PROTECT ENGINE

1. Change engine oil.

2. Remove spark plug.

3. Pour a tablespoon (5-10cc) of clean engine oil into the cylinder.

4. Pull the starter rope several times to distribute the oil in the cylinder.

5. Reinstall the spark plug.

6. Pull the starter rope slowly until resistance is felt. This will close the valves so moisture cannot enter the engine cylinder. Return the starter rope gently.

CHANGE OIL

While engine is still warm, drain oil from crankcase. Refill with recommended grade. See Changing Engine Oil in Engine Maintenance.

PROTECTING THE PUMP

To protect the pump from damage caused by mineral deposits or freezing, use PumpSaver or RV-antifreeze to treat the pump. This prevents freeze damage and lubricates pistons and seals.

• Failure to do so will permanently damage your pump and render your unit inoperable.

• Freeze damage is not covered under warranty.

To protect the unit from freezing temperatures:

1. Follow steps 1-3 in the previous section After Each Use.

2. Use pump saver to treat pump. This minimizes freeze damage and lubricates pistons and seals.

4. Store unit in a clean, dry area.

OTHER STORAGE INSTRUCTIONS

1. DO NOT store fuel from one season to another unless it has been treated as described in Protect Fuel System.

2. Replace fuel container if it starts to rust. Rust and/or dirt in fuel can cause problems if it’s used with this unit.

3. Cover unit with a suitable protective cover that does not retain moisture.

Storage covers can be flammable.

• DO NOT place a storage cover over a hot power washer.

• Let equipment cool for a sufficient time before placing the cover on the equipment.

4. Store unit in a clean and dry area.

TRANSPORTING/TIPPING OF THE UNIT

Do not operate, store or transport the unit at an angle greater than 15 degrees.

Hot oil may cause burns. Allow engine to cool before draining oil. Avoid prolonged or repeated skin exposure



with used oil. Thoroughly wash exposed areas with soap.

+ 50 hidden pages

Generac 6599, 6598, 6595, 6597 User Manual

Operator's Manual

Table of Contents

Introduction

SAFETY RULES

SAFETY SYMBOLS AND MEANINGS

WHERE TO FIND US

General Information

KNOW YOUR POWER WASHER

PRODUCT SPECIFICATIONS

EMISSIONS INFORMATION

HIGH ALTITUDE OPERATION

Set-up

UNPACKING

ASSEMBLY

ADD ENGINE OIL

ADD FUEL

CONNECT HOSE AND WATER SUPPLY TO PUMP

HOW TO USE NOZZLES

Operation

OPERATION

POWER WASHER LOCATION

CHECKLIST BEFORE STARTING ENGINE

HOW TO START YOUR POWER WASHER

Maintenance

AUTOMATIC COOL DOWN SYSTEM (THERMAL RELIEF)

HOW TO STOP YOUR POWER WASHER

MAINTENANCE RECOMMENDATIONS

MAINTENANCE SCHEDULE

PUMP OIL

EMISSIONS CONTROL

POWER WASHER MAINTENANCE

CHECK AND CLEAN INLET SCREEN

CHECK HIGH PRESSURE HOSES

CHECK DETERGENT SIPHONING TUBE

CHECK SPRAY GUN

NOZZLE MAINTENANCE

ENGINE MAINTENANCE

ENGINE OIL RECOMMENDATIONS

SERVICE AIR CLEANER

INSPECT MUFFLER AND SPARK ARRESTER

SERVICE SPARK PLUG

AFTER EACH USE

WINTER STORAGE

LONG TERM STORAGE

OTHER STORAGE INSTRUCTIONS

TRANSPORTING/TIPPING OF THE UNIT