Generac 1292-2 User Manual
High Pressure Washer Owner’s Manual
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
2300PSI
Model No. 1292-2 (2300 PSI High Pressure Washer) Manual No. B5715 Revision 2 (8/3/2000)
Visit our Generac website: www.generac-portables.com
Problems?
Questions?
Before taking your unit
back to the store,
call the pressure washer
helpline at
1-800-270-1408
M-F 8-5 CT
Generac Portable Products 2,300 PSI High Pressure Washer
2
EQUIPMENT DESCRIPTION
CONGRATULATIONS on your purchase of a
GENERAC high pressure washer. It has been
designed, engineered and manufactured to give you
the best possible dependability and performance.
This manual contains information for a high pressure
washer that operates at 2,300 PSI at a flow rate of
2.9 gallons per minute. This high quality residential
system features large 10 wheels, pump equipped with
an automatic cool down system, chemical injection
system, adjustable spray nozzle. Includes safety
goggles, heavy duty 25 hose, and more.
Please read and retain this manual. The instructions
will enable you to assemble your unit, and maintain
your high pressure washer properly.
Every effort has been made to ensure that the
information in this manual is both accurate and
current. However, Generac reserves the right to
change, alter or otherwise improve the product and its
documentation at any time without prior notice.
Should you experience any problem you cannot easily
fix, call the pressure washer helpline at
1-800-270-1408.
CUSTOMER
RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for
and using your high pressure washer.
For off-season storage, review Preparing The Unit
For Storage on page 13.
SAFETY RULES
CAUTION! When setting up, transporting,
adjusting or making repairs to your high
pressure washer, always disconnect the spark
plug wire from the spark plug and place the wire
where it cannot contact spark plug.
DANGER! Engine exhaust gases contain
DEADLY carbon monoxide gas. This dangerous
gas, if breathed in sufficient concentrations, can
cause unconsciousness or even death. Operate
this equipment only in the open air where
adequate ventilation is available.
DANGER! Gasoline is highly FLAMMABLE
and its vapors are EXPLOSIVE. Do Not permit
smoking, open flames, sparks or heat in the
vicinity while handling gasoline. Avoid spilling
gasoline on a hot engine. Allow unit to cool for
2 minutes before refueling. Comply with all laws
regulating storage and handling of gasoline.
Read this manual carefully and become familiar
with your pressure washer. Know its applications,
its limitations, and any hazards involved.
Locate this pressure washer in areas away from
combustible materials, combustible fumes or dust.
The high pressure equipment is designed to be
used with Generac authorized parts only. If you use
this equipment with parts that do not comply with
minimum specifications, the user assumes all risks
and liabilities.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea, fainting
or poisoning. The harmful elements may cause
property damage or severe injury.
Do Not allow CHILDREN to operate the pressure
washer at any time.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
WARNING:
Generac Portable Products 2,300 PSI High Pressure Washer
3
Operate engine only at governed speed. Running
the engine at excessive speeds increases the
hazard of personal injury. Do Not tamper with parts
which may change the governed speed.
Do Not wear loose clothing, jewelry or anything that
may be caught in the starter or other rotating parts.
Before starting the pressure washer in cold weather,
check all parts of the equipment and be sure ice has
not formed there.
Never use a spray gun which does not have a
trigger lock or trigger guard in place and in working
order.
Keep the hose connected to machine or the spray
gun while the system is pressurized. Disconnecting
the hose while the unit is pressurized is dangerous.
Units with broken or missing parts, or without
protective housing or covers, should Never be
operated.
Check the fuel system for leaks or signs of
deterioration, such as chafed or spongy hose, loose
or missing clamps, or damaged tank or cap. Correct
all defects before operating the pressure washer.
Do Not spray flammable liquids.
Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all
instructions with mask so you are certain the mask
will provide the necessary protection against inhaling
harmful vapors.
Never aim the spray gun at people, animals or
plants. The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury and
possible amputation.
Never allow any part of the body to come in contact
with the fluid stream. Do Not come in contact with a
fluid stream created by a leak in the high pressure
hose.
Always wear eye protection when you use this
equipment or when you are in the vicinity where the
equipment is in use.
High pressure spray can cause paint chips or other
particles to become airborne.
Do Not operate the pressure washer above the
rated pressure.
Never move the machine by pulling on the high
pressure hose. Use the handle provided on the unit.
Always be certain the spray gun, nozzles and
accessories are correctly attached.
Do Not secure the spray gun in the (open) position.
High pressure spray may damage fragile items
including glass. Do Not point spray gun at glass
when in the jet spray mode.
Hold the spray gun firmly in your hand before you
start the unit. Failure to do so could result in an
injury from a whipping spray gun. Do Not leave the
spray gun unattended while the machine is running.
The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to
slippery surfaces.
Operate and store this unit on a stable surface.
Keep water spray away from electric wiring or fatal
electric shock may result.
Do Not bypass any safety device on this machine.
The muffler and engine heat up during operation
and remain hot immediately after shutting it down.
Avoid contact with a hot muffler or engine as you
could be severely burned.
High pressure hose can develop leaks from wear,
kinking, abuse, etc. Water spraying from a leak is
capable of injecting material into skin. Inspect hose
each time before using it. Check all hoses for cuts,
leaks, abrasions or bulging of cover, or damage or
movement of couplings. If any of these conditions
exist, replace hose immediately. Never repair high
pressure hose. Replace it with another hose that
exceeds the maximum pressure rating of your unit.
The muffler and air cleaner must be installed and in
good condition before operating the pressure
washer. These components act as spark arresters if
the engine backfires.
In the State of California a spark arrester is required
by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws.
Federal laws apply on federal lands.
NOTE: If you equip the muffler with a spark arrester, it
must be maintained in effective working order. You can
order a spark arrester through your authorized Briggs
and Stratton service dealer.
Generac Portable Products 2,300 PSI High Pressure Washer
4
KNOW YOUR PRESSURE WASHER
Read this owners manual and safety rules before operating your high pressure washer.
Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
Adjustable Nozzle Always attached to nozzle
extension. Pull back for high pressure or push forward
for low pressure. Turn clockwise for narrow spray, turn
counterclockwise for fan spray.
Detergent Siphoning Tube and Filter Used to
siphon detergent from the chemical bottle into the low
pressure water stream.
Dual Element Air Filter Filter limits the amount of
dirt and dust that gets in the engine.
Gas Tank Fill tank with regular unleaded gasoline.
High Pressure Hose Connect one end to the
water pump and the other end to the spray gun.
High Pressure Outlet Connection for high
pressure hose.
Nozzle Extension Attach to spray gun to use
adjustable nozzle.
Oil Fill Cap Fill engine with oil here.
Pressure Control Knob Varies the pressure of the
high pressure spray.
Pump Develops high water pressure.
Recoil Starter Use for starting the engine
manually.
Safety Goggles Always use the supplied goggles
or other eye protection when running your pressure
washer.
Siphoning Tube Clip Used to hold the siphoning
tube when the siphoning tube is not being used.
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Water Inlet Connect garden hose here.
Spray Gun
Nozzle Extension
Adjustable Nozzle
High Pressure Hose
Recoil Starter
Safety Goggles
Gas Tank
Water Inlet
Pressure Control Knob
Pump equipped with
Automatic Cool Down System
High Pressure Outlet
Dual Element Air Filter
Oil Fill Cap
Detergent Siphoning
Tube and Filter
Siphoning Tube Clip
Generac Portable Products 2,300 PSI High Pressure Washer
5
WARNING! Read entire owners manual
before you attempt to assemble or operate your
new pressure washer.
REMOVE PRESSURE
WASHER FROM CARTON
Remove the high pressure hose and parts box
included with pressure washer.
Slice two corners at the end of carton from top to
bottom so the panel can be folded down flat, then
remove all packing material.
Roll pressure washer out of carton.
Carton Contents
Items in the carton include:
Main Unit
Parts Box (which includes the following):
High Pressure Hose
Wireform
Goggles
Nozzle Cleaning Kit
Owners Manual
Engine Manual
Owners Registration Card
Handle
2 Carriage Bolts
2 Knobs
Siphoning Tube Clip
1 Self Tapping Screw for Siphoning Tube Clip
Spray Gun
Nozzle Extension with Adjustable Nozzle
Oil Bottle
O-Ring Maintenance Kit
If any of the above parts are missing or damaged, call
the pressure washer helpline at 18002701408.
Preparing Pressure Washer for Use
If you have any problems with the assembly of your
pressure washer or if parts are missing or damaged,
call the pressure washer helpline at 1-800-270-1408.
To prepare your pressure washer for operation,
you will need to perform these tasks:
Remove shipping cap on top of pump.
Attach the handle and attach the wire form that
holds the high pressure hose and spray gun.
Connect the high pressure hose to the spray gun
and the pump.
Connect the water supply to the pump.
Add oil to the engine crankcase.
Add fuel to the fuel tank.
Remove Shipping Cap
To prevent oil from leaking from the pump, a shipping
cap has been installed on the oil breather of the pump.
You must remove the cap for your pressure washer to
operate properly (Figure 1).
CAUTION! Running unit with the shipping cap
installed will damage the pump and void your
warranty.
Attach Handle and Wireform
Place the handle onto the handle supports already
connected to the main unit. Make sure the holes in
the handle align with the holes on the handle
supports. (Figure 2)
Shipping Cap
Remove
shipping cap
from here.
Figure 1 Remove Shipping Cap on Top of Pump
Generac Portable Products 2,300 PSI High Pressure Washer
6
NOTE: It may be necessary to move the handle
supports from side to side in order to align the handle
so it will slide over the handle supports.
Insert the carriage bolts through the holes on the
handle and attach the plastic knobs. Tighten the
knobs by hand (Figure 3).
Attach siphoning tube clip onto the right side of the
handle (from the rear of the unit), with the self
tapper just underneath the billboard.
Insert the detergent siphoning tube into the clip on
the handle (Figure 4).
Insert the wire support with the longer arm
positioned on the left. From this view (from rear of
unit), the hook should resemble a J (Figure 5).
Add Engine Oil
IMPORTANT: Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil may result in an engine failure.
Place pressure washer on a level surface.
Refer to engine owners manual to add
recommended oil to engine.
NOTE: Check Oil Often During Engine Breakin.
NOTE: The pump is pre-lubricated and sealed,
requiring no additional lubrication for the life of the
pump.
Add Gasoline
DANGER! Never fill fuel tank indoors. Never
fill fuel tank when engine is running or hot. Do
Not smoke when filling fuel tank.
WARNING! Never fill fuel tank completely full.
Wipe away any fuel spillage from engine and
equipment before starting.
Use clean regular unleaded fuel and store in
approved clean covered containers. Use clean fill
funnels. Never use stale gasoline left over from
last season or gasoline stored for long periods.
Clean the area around the fuel fill cap, remove the
cap. Slowly fill tank to about 1/2 below the bottom
of the filler neck (Figure 6).
Make sure the
holes on the
handle are
aligned with the
holes on the
handle supports
Handle
Handle
Supports
Figure 2 Attach the Handle to the Base
Figure 4 Insert Detergent Siphoning Tube into Clip
Figure 5 Attach Wireform
Figure 6 Add Gasoline to Fuel Tank
Siphoning Tube Clip
Figure 3 Secure Handle
Loading...