Genaray LED-2100 User manual
LED-2100
USER MANUAL
INTRODUCTION
Thank you for choosing the Genaray LED-2100 On-Camera Light. This
product will provide you with powerful, portable and dependable illumination
that can be used in a variety of settings. Featuring advanced light dispersion
capabilities and supporting accessories that add instant versatility to this
light kit, the Genaray LED-2100 On-Camera Light proves to be the perfect
choice for photographers and videographers alike.
Built-In
Diffuser
LED
Array
Locking
Ring
KEY FEATURES
· Integrated Shoe Mount
Connects To DV & HDSLR
Cameras
· Unit Has 25' Lighting Range &
65° Illumination Angle
· Stackable Mounting Feature
Interlocks With Other Units
· Mounting Bracket Connects To
1/4 20 Camera Tripod Screw
1/4 20
Threaded
Mount
Cold Shoe
Mount
PRODUCT CONTENTS
1 - LED Light With Built-In
Diffuser & Shoe Mount
1 - Thread Adapter for Sony
AIS Shoe Mount
1 - Included Camera Mounting Bracket
2 - 700mAh Li-Ion Rechargeable
1-Hour Batteries
1 - 110-240V AC/DC Wall Charger
1 - European Plug Adapter
Power
Switch
Battery
Compartment
Cover
Interlocking
Expansion
Slots
POWERING LED LIGHT
· Open latch found on battery compartment
cover by squeezing tab upwards; hold tab
in upward position and remove the entire
cover
· Install fully-charged battery by sliding it into
battery compartment; ensure that goldcolored battery conductor contacts face
upwards and are touching metal
prongs in the battery mounting area
· Replace battery compartment cover
· Move the power switch into the
ON position to illuminate the LEDs
MOUNTING LED LIGHT ON CAMERA
· Begin by positioning light unit directly
atop camera or video camera
· Ensure that locking ring is fully loosened
and slide cold shoe mount into shoe of
camera; rotate ring clockwise to lock light
into place securely
· Do not attempt to disassemble,
repair or perform any
unauthorized modifications on
device
· Do not handle with wet hands,
immerse in liquids or expose to
water and rain; electric shock
or fire may result
· Device contains small parts
which may pose a choking
hazard; keep out reach of
children
SAFETY WARNINGS
· Do not operate device in
presence of flammable gas or
vapors
· Do not use product if it emits
smoke or a strange odor;
disconnect power source
immediately to avoid personal
injury and contact place of
purchase
· Observe caution when handling
batteries; only use batteries
approved by the manufacturer
of this product
· Batteries are prone to leakage
when fully discharged; to avoid
damaging product be sure to
remove batteries when leaving
product unattended
· Do not intentionally stare or
gaze at LED light panel f
prolonged periods while device
is on
· Do not use or leave device in
conditions of extreme heat,
severe cold or high humidity
· Unit will display a decrease in
brightness when the battery
runs low; be sure to replace
battery when necessary to
avoid affecting recording quality
MOUNTING LED LIGHT ON BRACKET
· Included mounting bracket is designed for
point-and-shoot cameras that have no shoe
mount; begin by mounting light on cold shoe
found on bracket
· Insert 1/4 20 screw found on bracket into
the 1/4 20 threading mount found on bottom
of camera; adjust spacing of camera by
sliding knob along length of bracket arm
and secure tightly
INTERLOCKING WITH OTHER LED UNITS
· Ensure that device locking ring is fully
loosened and slide cold shoe mounting
into interlocking expansion slot of another
compatible Genaray LED light unit; rotate
ring clockwise to lock light in place securely
· Up to 3 compatible Genaray LED light units
can be mounted to each individual light unit
or in a stacked vertic
al format for increased
illumination
· When cleaning the device, use
only a mild detergent solution
and quickly wipe dry with a
soft cloth
· Please dispose of used
batteries, packaging and old
devices in accordance with
appropriate environmental
regulations
or
CUSTOMER SUPPORT
Please send email
correspondence to:
info@genaray.com
LIMITED 1 YEAR WARRANTY
See website for details
www.genaraylighting.com
MANUAL
LED-2100 - USER MANUAL
Loading...