Page 1
Warming drawers
ZTD910BB
ZTD910BB
26-3/4" for 27" Models
30" for 30" Models
10-1/2"
1-13/16"
1-3/4"
Drill 5/16" Dia.
Through Custom
Panel For Lamp Jewel
General features
Sophisticated styling. Built-in design with hidden controls offers
a look of understated elegance. For a personal statement,
customize the drawer with a cabinet-compatible wood panel
and your choice of handles.
Temperature settings. Monogram warming drawers offer a
range of temperature options, from a proof setting (approximately
75°F) to a high setting (approximately 230°F).
Humidity control. By opening or closing the warming drawer vent,
you can keep foods crisp or maintain moisture.
Practical details. The design of the half rack not only
distributes heat evenly, but it also provides fifty percent
more surface area for stacking plates and food.
Installation versatility. All 30" and 27" warming drawers are
UL listed for use with Monogram wall ovens and cooktops.
Three-pan set. A set of three covered pans allows a choice of
sizes for any dish: one 6-quart pan and two 3-quart pans.
For additional details on product installation, warranty coverage,
care and maintenance, visit monogram.com.
30" warming drawer
ZTD910SFSS
Overall dimensions
(WxHxD in inches):
30 x 10-1/2 x 23-1/4
Amps @120VAC 15
Approx. shipping wt. (lbs.) 65
•
Optional custom wood
panel kit
•
Side-by-side installation
•
Undercounter installation
•
Under-wall-oven installation
•
Under cooktop installation
monogram.com
monogram.com
27" warming drawer
ZKD910SFSS
Overall exterior dimensions
(WxHxD in inches):
26-3/4 x 10-1/2 x 23-1/4
Amps @120VAC 15
Approx. shipping wt. (lbs.) 59
•
Optional custom wood
panel kit
•
Side-by-side installation
•
Undercounter installation
•
Under-wall-oven installation
•
Under cooktop installation
Speedcook
®
wall ovens
Advantium
Speedcook ovens
Above-the-cooktop
Advantium
Advance planning for warming drawers
Electrical requirements
Product rating is 120V, 60Hz, and must be connected to an
individual, properly grounded branch circuit and protected
by a 15- or 20-amp circuit breaker or time-delay fuse.
Two warming drawers installed side by side can operate
from the same duplex outlet.
Professional door panel with handle
The drawer front of the 30" model ZTD910SFSS can be removed
and replaced. Order ZXD30P Professional door panel.
Microwave ovensWarming drawers
Microwave ovens
Custom panels and handles
The drawer fronts can be removed and replaced with a
custom panel to match surrounding cabinetry.
• Order ZXD30B for 30"-wide models and ZXD27B for 27"
models. These kits must be ordered separately from your
Monogram supplier.
• The tubular handle may be reinstalled onto the custom panel
(longer screws will be required) or replaced with a custom
handle of your choice.
* Note: The custom panel will not be flush with adjacent
cabinetry drawers and doors.
29
Page 2
Advance planning for warming drawers
2"
Min.
Side-by-Side Installation
Installation below a single or double oven
The warming drawer may be installed below a single or double
oven. Observe the 1" minimum clearance above the toekick, or
5" above the floor.
30" warming drawer
ZTD910SFSS Stainless steel
27" warming drawer
ZKD910SFSS Stainless steel
23-1/2" Min.
Inside
Single
oven
Oven
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
1" Min. Above Toekick or Adjust
to Oven Installation Height
Cutout
9"
9-1/4"
2" Min.
Allow 5/8"
Overlap on
All Sides
A
23-1/4"
10-1/2"
B
Dim. A Dim. B
ZTD910 28-1/2" 30"
ZKD910 25-1/2" 26-3/4"
Side-by-side installation
Install two warming drawers in separate cutouts. Allow 2"
minimum between cutouts.
Installation below a countertop
The warming drawer may be installed beneath a countertop.
Install the drawer 5" minimum above the
the toekick. The recommended distance
floor or 1" above
from the floor to the
bottom of the cutout is 23-1/4" for undercounter installation.
Installation below a cooktop
The warming drawer is approved for installation below
specified cooktop models. A solid barrier and an air gap
between the cooktop and the warming drawer are required.
See note below.*
Installation below a cabinet drawer
The warming drawer may be installed beneath a cabinet
drawer. In this installation, a solid barrier should be installed
above the warming drawer to block access. Use any solid
material such as 1/4"-thick plywood. Allow at least 1/4" air
gap between the barrier and the top of the warming drawer.
Note: Additional clearance between cutouts may be
required. Check to be sure that oven supports, above the
warming drawer location, do not obstruct the required
interior 23-1/2" depth and 9-1/4" height.
23-1/2" Min.
Double
Inside
oven
Allow 5/8"
Overlap on
All Sides
2" Min.
23-1/4"
B
2x2 or 2x4
Anti-Tip Block
Against Rear
Wall, 9" From
Floor to
Bottom of
Block
Oven
Cutout
9"
9-1/4"
1" Min. Above Toekick
A
10-1/2"
Electrical
Outlet 16" Max.
From Left Side.
Dim. A
ZTD910 28-1/2"
23-1/2" Min.
Install
2x4 or 2x2
Anti-Tip Block
Against Rear
Cabinet Wall
9" From Floor
to Bottom
of Block
9"
Solid Barrier
1/4"
Air Gap
Install a Solid Barrier
and a 1/4" Air Gap
Above Warming Drawer
Electrical Outlet
Flush With
Side of Cabinet
7" Max.
7"
Installation Below
a Drawer
Electrical Outlet
42" Max. From
Solid Barrier
See Note
A
Right Side.
25"
1" Min.*
9-1/4"
1-1/2"
Cabinet
Top
36"
Countertop
Height
ZKD910 25-1/2"
Dim. A Dim. B
ZTD910 28-1/2" 30"
ZKD910 25-1/2" 26-3/4"
* Note: When installing the warming drawer below a cooktop,
a solid barrier must be installed at least 1" from the lowest
point of the bottom of the cooktop burner box to the top of
the cutout. Use any solid material such as 1/4"-thick
plywood. Allow at least 1/4" air gap between the barrier
30
and the top of the warming drawer.
Loading...