GE ZIS360N, ZISB360D, ZISW360D, ZISS360N, ZISS360D Installation Instructions

Monogram.

®

If you have questions, call 800.626.2000 or visit our website at: www.monogram.com

Installation
Instructions

Side by Side Refrigerators

ZIS360N, ZISB360D, ZISW360D
ZISS360N, ZISS360D

ZIS420N, ZISB420D, ZISW420D
ZISS420N, ZISS420D

ZIS480N, ZISB480D, ZISW480D
ZISS480N, ZISS480D

Design Guide
With Installation Instructions

Safety Information

Skill Level - Installation of this refrigerator

requires basic mechanical, carpentry and plumbing
skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See
the Owner’s Manual for warranty information.

WARNING:

• These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page
12 for details.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric service cords
that become frayed or damaged.

• Unplug the refrigerator before cleaning or making
repairs.

• Repairs should be made by a qualified service
technician.

AVERTISSEMENT

• Ces réfrigérateurs sont lourds en haut et il faut les
arrimer pour éviter leur basculement. Il faut avoir
un système de protection contre le renversement.
Voir les détails page 12.

• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.

• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.

• Il faut débrancher le réfrigérateur avant le
nettoyage ou toute intervention.

• Les réparations doivent être faites par un
technicien qualifié.

For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call

1-800-626-2002.

www. monogram.com

2

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Save these instructions for

local inspector’s use. Observe all governing codes and
ordinances.

• Note to Installer - Be sure to leave these
instructions with the Consumer.

• Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.

WARNING:

This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 10.

AVERTISSEMENT

Cet appareil doit être correctement mis à la terre.
Consulter « Mise à la terre du réfrigérateur », page 10.

If you received a damaged refrigerator, you should
immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to
the product – THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION OF A 36" WIDE
UNIT. FOUR PEOPLE ARE REQUIRED FOR
INSTALLATION OF A 42" OR 48" WIDE MODEL.

PRUDENCE

À cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages,
IL FAUT TROIS PERSONNES POUR INSTALLER
CORRECTEMENT D’UN APPAREIL DE 91 cm (36 po)
DE LARGE. IL FAUT QUATRE PERSONNES POUR
L’INSTALLATION D’UN MODÈLE DE 107 OU 122 cm
(42 OU 48 po) DE LARGE.

CONTENTS

Planning Guide

The Installation Space ....................................3

Dimensions and Clearances ..........................3

130° Door Swing ..............................................4

90° Door Swing ................................................5

Customization Basics ......................................6

1/4" Framed Panel Dimensions ......................7

3/4" Overlay Panel Dimensions ......................8

Raised Overlay Panel Design ........................9

Side Panels......................................................10

Installation Instructions

Tools, Hardware, Materials ........................10

Grounding the Refrigerator ..........................10

Step 1, Remove Packaging ..........................11

Step 2, Install Water Line ............................11

Step 2A, RO Water Line ................................12

Step 3, Install Side Panels ..........................12

Step 4, Install Anti-Tip Brackets ................12

Step 5, Level Refrigerator ............................13

Step 6, Secure Refrigerator to Cabinetry ..13

Step 7, Adjust Door Swing ..........................13

Step 8, Install Grille Panel ............................14

Step 9, Install Framed Panels ......................15

Step 9A, Install Overlay Panels ..................16

Step 10, Install Dispenser Trim ....................17

Step 11, Connect Water Supply ..................17

Step 12, Connect Power ..............................18

Step 13, Start Icemaker ................................18

Step 14, Install Toekick ................................18

B

A

Design Guide

THE INSTALLATION SPACE

Water And Electrical Locations

The opening must be prepared with the electrical
and water supply located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.

Note: GFI (ground fault interrupter) is not
recommended.

• Water line can enter the opening through the

floor or back wall. The water line should be 1/4"
O.D. copper tubing or GE SmartConnect™ kit
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible shut
off valve in the water line is required.

DIMENSIONS AND CLEARANCES

* Shipping height. The

refrigerator can be
adjusted to fit into a
cutout that is 83-1/2"
min. to 84-1/2" max.
height. Note that the
top case trim at the
front is 1/2" higher
and will overlap
upper cabinetry or
soffit. Use leveling
legs and wheels for a
maximum 1” height
adjustment.

Product Clearances

These refrigerators are equipped with a 2 position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets or
walls is restricted.

3

*The finished cutout width must be:

35-1/2" for 36" models
41-1/2" for 42" models
47-1/2" for 48" models

90° Door Swing130° Door Swing

*Finished Width

6"

5"

Electrical
Area

84 1/2" max

83 1/2" min

Finished
Opening

75" From Floor

to Bottom

of Electrical

Area

24"

5"

5"

3 1/2"

Water Supply

3 1/2"

36" Models 12"
42" Models 18"
48" Models 20"

Allow minimum clearances for freezer door
(Dimension A) and fresh food door (Dimension B)
for a full 130° door swing and to allow for pan
removal.

4" minimum clearance is required when door swing
is adjusted to 90°. If the 90° door stop position is
used, pan access is maintained, but pan removal is
restricted.

See illustrations pages 4 and 5 to determine
door swing interaction with adjacent cabinets or
countertops.

23-7/8"
Behind

Frame

C

90° Door Swing

4" Min.
to Wall

Models A B C
36" 13" 15" 20-5/8"
42" 13" 19" 26-5/8"
48" 15" 20" 28-5/8"

*84" From
Floor to
Top Frame

25-3/8" Framed Models
25-3/4" Stainless Steel Models
Case Depth

Depth Including Handles:
26-7/8" Framed Models
27-3/4" Stainless Steel Models

36", 42", or 48"

Frame to Frame

35", 41", or 47"

Case Width

*83-1/2"

at

Rear

194D a57

1/4"

1/2"

3/4"

1"

1-1/4"

1"

3/4" Overlay

Panel

(Nominal Size)

1/4"

1/2"

3/4"

2"

1-1/4"

1-1/2"

1-3/4"

3"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

1"

Refrigerator

Case
Trim

Design Guide

Top View
130° DOOR SWING
(factory setting)
Scale 1:1

IMPORTANT NOTE –
FOR DISPENSER MODELS:

Dispenser models are supplied with two
dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser trim

fit to the custom panel depends on correct
panel thickness. Framed panels must be

1/4" nominal. Overlay panels should be
constructed as shown to accomplish a total

1.100" thickness. See pages 7 and 8 for details.

4

Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interfeence with cabinet
door swing. The opening must allow for filler
strips.

1/4"

1/2"

3/4"

1"

1-1/4"

1/4"

1/2"

3/4"

1"

1-1/4"

1-1/2"

23-7/8"

From Rear of

Refrigerator

3/4" Overlay

Panel

(Nominal Size)

Case Trim

Refrigerator

Door

5

Top View
90° DOOR SWING
(optional setting)
Scale 1:1

IMPORTANT NOTE –
FOR DISPENSER MODELS:

Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlay
panels. Dispenser trim fit to the

custom panel depends on correct
panel thickness. Framed panels

must be 1/4" nominal. Overlay panels
should be constructed as shown to
accomplish a total 1.100" thickness.
See pages 7 and 8 for details.

Frameless Cabinets:

The case trim overlaps
cabinets at the top
and sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference with
cabinet door swing. The
opening must allow for
filler strips.

Design Guide

Standard Door Handles

3/4" Overlay Panel

.10" Thick Spacer Panel

1/4" Thick Backer Panel

CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits

Overlay panels

You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetry.

Standard supplied handles shown in 3/4" overlay panel position.

Stainless Steel Wrapped Models

36" wide models - ZISS360N, ZISS360D
42" wide models - ZISS420N, ZISS420D
48" wide models - ZISS480N, ZISS480D

Trimmed Models

36" wide models - ZIS360N, ZISB360D, ZISW360D
42" wide models - ZIS420N, ZISB420D, ZISW420D
48" wide models - ZIS480N, ZISB480D, ZISW480D

Stainless Steel Wrapped Refrigerators

Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.

Framed panels

You may install 1/4" thick custom panels from your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels from your Monogram
dealer.

6

Standard supplied handles shown in 1/4" panel position.

Door Handles

The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you
may order ZKHSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.

Side Panels

Side panels must be used whenever the sides of the
refrigerator will be exposed.

Optional Accessory Kits

ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels.

Accessory Panels

White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut to
size and ready to install.

Models White Black Stainless

Acrylic Acrylic Steel

ZISW480D ZPW480D ZPS480D
ZISB480D ZPB480D ZPS480D
ZIS480N ZPW480N ZPB480N ZPS480N
ZISW420D ZPW420D ZPS420D
ZISB420D ZPB420D ZPS420D
ZIS420N ZPW420N ZPB420N ZPS420N
ZISW360D ZPW360D ZPS360D
ZISB360D ZPB360D ZPS360D
ZIS360N ZPW360N ZPB360N ZPS360N

Framed Panel

Standard Door Handles

Design Guide