GE Monogram
Installation
Instructions
®
www.monogram.com
Stainless Steel
36" Built-In
Refrigerators
and Freezers
Models
ZIRS36N LH – All Refrigerator
ZIRS36N RH – All Refrigerator
ZIFS36N LH – All Freezer
ZIFS36N RH – All Freezer
Before you begin – Read these instructions completely and carefully.
IMPORTANT – Save these instructions for local inspector’s use.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
WARNING
ATTENTION
If you received a damaged product, you should
immediately contact your dealer or builder. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See the Owner’s Manual
for warranty information.
For Monogram local service in your area,
1.800.444.1845.
For Monogram Service in Canada,
1.888.880.3030.
For Monogram Parts and Accessories, call
1.800.626.2002.
This appliance must be properly grounded. See “Grounding the Refrigerator,” page 7.
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à terre du réfrigérateur », page 7.
CAUTION
Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to
the product – THREE PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
PRUDENCE
À cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages,
IL FAUT TROIS PERSONNES POUR FAIRE
L’INSTALLATION CORRECTEMENT.
WARNING
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service
cords that have become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
ATTENTION
• Il ne faut utiliser cet appareil que pour l’usage
pour lequel il a été construit.
• Il faut réparer ou remplacer immédiatement tout
cordon d’alimentation électrique effiloché ou
endommagé.
• Débrancher le réfrigérateur avant le nettoyage ou
toute intervention.
• Les réparations doivent être faites par un
technicien qualifié.
Contents
2
Design Information
Flush or Semi-Flush Enclosure Installations ........ 3
Enclosure Cutout and Product Dimensions ..... 3, 4
Accessory Grille Panel Kits..................................... 4
Installation Examples ........................................... 4, 5
Product Dimensions ................................................. 5
Installation Preparation
Clearances ................................................................. 6
Electrical and Water Connection Location .......... 6
Grounding the Refrigerator ..................................... 7
Tools Required ........................................................... 8
Materials Required ................................................... 8
Hardware Supplied ................................................... 8
Hardware Recommendations ................................. 8
Flooring ....................................................................... 8
Step 1: Remove Packaging ...................................... 8
Installation Instructions
Step 2: Install Water Line......................................... 9
Step 3: Install Side Panels ..................................... 10
Step 4: Install Anti-Tip Brackets........................... 10
Step 5: Level Refrigerator ...................................... 11
Step 6: Optional Anti-Tip Precaution ................... 11
Step 7: Connect Water Supply.............................. 12
Step 8: Connect Power .......................................... 12
Step 9: Mount Top Grille Panel ............................. 12
Step 10: Adjust Door Alignment .......................... 13
Step 11: Install Toekick........................................... 13
Step 12: Set Temperature Controls ...................... 13
Step 13: Start Icemaker ......................................... 13
Problem Solving ...................................................... 13
ZUGSS Unified Grille Panel Kit.............................. 14
Design Information
Flush or Semi-Flush Enclosure Installations
Advance Planning
0"
True Flush Installation
In a flush installation,
the refrigerator door
will align evenly with the front
face of adjacent cabinet doors.
The refrigerator blends into the
surrounding cabinetry.
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator will
project forward approximately 3/4" beyond the front
face of surrounding cabinetry.
36" Stainless Steel Refrigerators, Freezers
3/4"
Semi-Flush Installation
These refrigerators
can also be installed
semi-flush into an enclosure
using the minimum cutout
width. The case trim creates a
frame around the opening.
Side Panel Requirements:
• Side panels are not required whenever the
refrigerator or freezer is installed into an enclosure
or between pantry and oven cabinets.
• Side panels are required whenever the sides of the
product are exposed.
• Side panel sizes vary depending on the type of
installation being made.
Enclosure Cutout and Product Dimensions
•
To achieve a flush fit, the finished cutout width must be
at least 36" wide.
•
In a semi-flush installation, the finished cutout must be
35-1/2".
• The electrical and water locations must be located
as shown for either type of installation.
35"
24-3/4"
Case
Case
Width
Depth
84"*
26-3/4"
Including
Tubular
Handles
36" Frame to Frame
*Shipped at 84" installation height.
Can be adjusted to 83-1/2"
or 84-1/2" with grille panel kits.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet
manufacturer. Be sure to provide the exact dimensions.
*Finished Width
2 1/2"
5"
84 1/2" max
83 1/2" min
Finished
Opening
*36" for a flush installation.
35-1/2" Min. for a semi-flush installation.
NOTE: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width. See installation examples
on the following page.
24 3/4" Total
Depth
5"
3 1/2"
Electrical
Area
6"
Water Supply
5"
Wall View
75" From Floor
to Bottom
of Electrical
Area
3 1/2"
3
Design Information
Cabinet
Refrigerator door
Refrigerator
Cabinet
36" Stainless Steel Refrigerators, Freezers
Side By Side
Installation
Of Freezer
And Refrigerator
84 1/2" max
83 1/2" min
Finished
Opening
3 1/2"
For a complete food storage center, install a Monogram
Freezer and Refrigerator side by side. For even more
capacity, install two refrigerators and one or two freezers.
• Order ZUGSS Unified Grille Panel Kit for one
continuous stainless steel grille panel.
• Electrical and water locations must be located as
shown for either type of installation. A separate
115V, 60Hz, 20 amp power supply is recommended
for each product.
*Finished Width
2 1/2"
Electrical
6"
5"
24 3/4" Total
Depth
5"
Water Supply
26"
Freezer Refrigerator
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
NOTE: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished cutout
to calculate rough-in width. See installation examples below.
6"
28 1/2"
5"
Wall View
75" From Floor
to Bottom
of Electrical
Area
Accessory Grille Panel Kits
Installation Examples
Installation
Between
Base and
Wall Cabinets
These models are factory set for 84" installation height.
Adjustments to 83-1/2" or 84-1/2" heights can be made
by changing the grille panel.
Order ZGCSS36RH (right hand) or ZGCSS36LH (left
hand) Grille Panel Kit. These kits include 2 grille panels,
for 83-1/2" and 84-1/2" installation heights.
Side panels are required whenever the sides of the
product will be exposed.
1/2" to 3/4" side panels are normally set into place and
fastened to adjacent cabinetry or to the back wall before
rolling the refrigerator or freezer into the opening.
1/4" Thick
Side Panels
Refrigerator or Freezer
Finished Dim.
Rough-In Dim.
NOTE: 1/4" thick side panels can be inserted
into the case trim, making the rough-in the
same as the outside trim width: 36”.
35-1/2"
36"
ZUGSS Unified Grille Panel Kit
For side by side installation, order ZUGSS grille panel
kit. This kit provides one continuous panel to span the
width of two products installed together for a unified
appearance.
Therefore, the rough-in dimensions must allow for
side panel thickness. In both a flush and semi-flush
installation, the finished dimension (the width of
the opening after side panels are installed) must
accommodate the full width of the product.
See page 10 for side panel sizes.
4
Installation
Cabinet
Refrigerator
Cabinet
Refrigerator door
10-3/4" Max.
10" Min.
24-3/4"
35" Case
36" Overall
84-1/2" Max.
83-1/2" Min.
4"
73-1/2"
26-3/4"
At End-of-Run
Design Information
36" Stainless Steel Refrigerators, Freezers
1/2" Thick
Side Panels
Frameless
Cabinets
Finished Dim.
Roughed-In Dim.
Refrigerator or Freezer
Finished Dim.
Refrigerator and Freezer
installed side-by-side
Side panels, 1/2" minimum thickness are required when
using frameless cabinets. The side panel acts as a
spacer between the cabinet and the case trim and
prevents interference with cabinet door swing.
The leading (front) edge must be finished to match
surrounding cabinetry.
Rough-In Dim.
36"
37"
1/2" To 3/4" Side Panels. Leading
Edge Flush With Cabinet
1/2" Thick
Side Panels
72"
73"
NOTE: 1/2" thick side panels shown.
Side panels can be any thickness.
Add side panel thickness to outside
trim width, (36” or 72" for two models)
to calculate the rough-in dimension.
The leading (front) edge must be
finished to match surrounding
cabinetry.
Refrigerator
Cabinet
Refrigerator door
Product Dimensions
ZIRS36N RH, Refrigerator
ZIFS36N RH, Freezer
Handle on the left side, the door swings left to right.
ZIRS36N LH, Refrigerator
ZIFS36N LH, Freezer
Handle on the right side, the door swings right to left.
CAUTION
Refrigerators are much heavier at the top than at
the bottom – be extra careful when moving.
PRUDENCE
Les réfrigérateurs sont beaucoup plus lourds en
haut qu’en bas. Il faut être prudent lors des
déplacements.
5
Installation Preparation
36" Stainless Steel Refrigerators, Freezers
Clearances
25"
130° Door
Swing
130°
Factory set for a 130° door swing. Order WX14X99
adjustable door stop to reduce swing to as little as 90°.
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for pan
removal. Allow 4" min. clearance when door swing is
adjusted to a 90° opening for pan access, but pan
removal is restricted.
25"
Min. to
Wall
Min. to
Wall
0"
130° Door
Swing
130° Door
Swing
90° Door Swing
4" Min.
to Wall
25"
Min. to
Wall
2"
36-3/4"
Clearances for two products installed side-by-side
with the same (left or right) door swing
Allow 2" minimum clearance between the products to
prevent door swing interference. Order the WX14X99
adjustable door stop to reduce the factory set 130°
door swing. Allow 15" minimum to a wall to achieve
full drawer extension and pan removal.
NOTE: ZUGSS Grille Panel Kit will not fit this installation.
5"
15"
Electrical
and Water
Connection
Locations
Clearances for Multiple Single Door Installations
In a side-by-side installation of a left and right door
swing product, no clearance between the units is
required. Order ZUGSS Stainless Steel Unified Grille
Panel Kit for one continuous grille panel.
The water line can be routed through the floor or
back wall.
• The icemaker water line should be:
– Approximately 3-1/2" from the floor on the back wall,
or 3-1/2" from the back wall on the floor.
– At least 5" from either side of the opening.
A 115 volt, 60 Hz 15 or 20 amp power supply is
recommended. An individual properly grounded
branch circuit or circuit breaker is recommended,
as noted on the rating plate.
• Locate the electrical outlet within 5" x 6" shaded area
shown.
– 2-1/2" from the left side.
Between 75" and 81" from the floor.
IMPORTANT: To insure a flush fit and access to the
power cord, locate the electrical outlet as shown.
Clearances for two products installed side-by-side
with right and left side hinges together
Allow 5" minimum between the two products to prevent
one door from striking the other. Use the WX14X99
adjustable door stop to reduce the factory set 130°
door swing and to allow pan removal.
NOTE: ZUGSS Grille Panel Kit will not fit this installation.
Electrical Outlet
Location 2 1/2"
6"
5"
75"
5"
3 1/2"
Water Location
6
Installation Preparation
36" Stainless Steel Refrigerators, Freezers
Grounding the Refrigerator
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with a
3-prong (grounding) plug that mates with a standard
three-prong (grounding) wall receptacle to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
IMPORTANT:
We recommend two separate 115V, 60Hz, 20 amp
properly grounded electrical outlets for a side by side
installation of two products. Each electrical outlet should
have a voltage rating that matches the rating plate.
Use of Adapter plug
Because of potential hazards under certain
conditions, we strongly recommend against use of
an adapter plug. However, if you still elect to use an
adapter, where local codes permit, a TEMPORARY
CONNECTION may be made to a properly grounded
2-prong wall outlet by use of a UL listed adapter
available at most hardware stores.
The larger slot in the adapter must be aligned with the
larger slot in the wall outlet to provide proper polarity
in the connection of the power cord.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM THE
POWER CORD.
When disconnecting the power cord from the adapter,
always hold the adapter in place with one hand and pull
the power cord with the other hand. If this is not done,
the adapter ground terminal is very likely to break with
repeated use.
Should the adapter ground terminal break, DO NOT USE
the appliance until a proper ground has again been
established.
Use of Extension Cords
Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord. However, if you still elect to use an
extension cord, it is absolutely necessary that it be a
UL listed, 3-wire grounding type appliance extension
cord having a grounding type plug and outlet, and that
the electrical rating of the cord be 15 amperes
(minimum) and 120 volts.
PRUDENCE
FICHE D’ADAPTATION
(Fiches d’adaptation non permises au Canada)
CAUTION
Attaching the adapter ground terminal to a wall
outlet cover screw does not ground the appliance
unless the cover screw is metal, and not insulated,
and the wall outlet is grounded through the house
wiring. You should have the circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
7
Installation Preparation
36" Stainless Steel Refrigerators, Freezers
Tools Required
Materials Required
Hardware Supplied
Hardware Recommendations
Flooring
• Tinsnips to cut banding
• Stepladder
• Bucket
• Level
• 1-1/4" open-end wrench
• 2x4, 35" long, for Anti-Tip support, see page 10
• Stick-on hook and loop fastener strips for 1/4" side panels
• 1/4" copper water line tubing or GE SmartConnect™ Tubing Kit
• 1/4-1/4 union with nuts
• Anti-tip mounting brackets
• Water shut-off valve
• Water filter WR97X0214
For proper installation, the refrigerator and freezer must
be placed on a level surface of hard material that is at
the same height as the rest of the flooring. The floor
must be strong enough to support a fully loaded product,
or approximately 1,200 lbs.
• Appliance hand truck
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Stubby Phillips screwdriver
• Drill and appropriate bits
• 7/16" socket with 3" extension for
ratchet
• Safety glasses
• Water shut-off valve
• Screws to secure refrigerator to cabinetry
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
product where you are working.
Step 1
Remove
Packaging
8
CAUTION
Refrigerator is much heavier at the top than at the
bottom – be careful when moving. When using a
hand truck, handle from side only.
PRUDENCE
Le réfrigérateur est beaucoup plus lourd en haut
qu’en bas. Il faut être prudent lors des déplacements.
Si un diable est utilisé, il faut soulever le réfrigérateur
sur le côté seulement.
• Remove outer carton.
– Carefully cut banding at the top and bottom.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
• Remove styrofoam pads taped to base cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN
IN ORDER TO REMOVE SKID!
• The unit is secured to the skid with 3 slotted tie-down
straps. First remove the 5/16" bolts from the base
channels in the tie-downs, then remove the 7/16" bolts
securing the straps to the skid.
• Protect the flooring. Cut a large piece of the cardboard carton and place under the product where you
are working.
• Support blocks on the bottom must be removed before
the refrigerator is taken off the skid or damage will
occur. Remove support blocks by carefully tilting
cabinet to side and sliding out.
• Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.
7/16" Bolt
CAUTION
DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
PRUDENCE
IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE
RÉFRIGÉRATEUR POUR L'ENLEVER DE LAY PALETTE.
Installation
36" Stainless Steel Refrigerators, Freezers
Step 2
Install
Freezer
Water Line
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 20 and 120 p.s.i.
™
• Route 1/4" OD copper or GE SmartConnect
between house cold water line and the water
connection location.
• Tubing should be long enough to extend to the front
of the freezer. Allow enough to accommodate bend
leading into the water valve.
NOTE: The only GE approved plastic tubing is supplied
in the GE SmartConnect
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
GE SmartConnect
available in the following lengths:
2' (0.6 m) WX08X10002
6' (1.8 m) WX08X10006
15' (4.6 m) WX08X10015
25' (7.6 m) WX08X10025
Shut off the main water supply
Turn on the nearest faucet long enough to clear the line
of water.
™
Refrigerator Tubing Kits.
™
Refrigerator Tubing Kits are
tubing
Floor
Tubing
Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
• Install optional water filter in the water line near the
freezer. A water filter is recommended in areas where
water supply contains sand or particles. Installation
instructions are packed with the filter.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
9
Installation
36" Stainless Steel Refrigerators, Freezers
Step 3
Install
Side Panels
• Side panels are required whenever the sides of the
product will be exposed and when installed between
frameless cabinets. See pages 3 and 4.
• Side panels are not required when installed into an
enclosure.
• Side panel installation will be determined by the
design of the side panel you have previously chosen.
• Side panels must be installed plumb.
Illustration A
1/4" Side Panels –
Insert end of side
panel into case trim.
Trim
Top View
Standard 4" high toekick or trim to fit. Height
may vary depending on application.
23-9/16"
84"
2-9/16"
• If you choose to use 1/4" side panels, they should be
inserted into the case trim as illustrated. Fasten the
panels to the product with stick-on hook and loop
fastener strips before setting in place. See
illustration A.
• 1/2" to 3/4" side panels are normally set into place and
fastened to adjacent cabinetry or the back wall before
rolling the product into the opening. See illustration B.
Illustration B
1/2" to 3/4" Side
Panels – Leading
edge of side panel is
flush with cabinet
front. Fasten to the
back wall using a
cleat.
Top View
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
24-3/4"
84"
3-3/4"
Step 4
Install
Anti-Tip
Brackets
10
WARNING
ANTI-TIP PRECAUTIONS
The refrigerator is top-heavy and must be secured
to prevent the possibility of tipping forward.
ATTENTION
PRECAUTIONS CONTRE LES BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut
et il faut le maintenir en place pour éviter la
possibilité de son basculement vers l’avant.
• Cut a 2" x 4" x 35" block and secure the block to
the mounting brackets provided using #12 or #14 wood
screws.
• Secure the bracket with wood block to the back wall
so that it is 84" (or your installation height) from the
finished floor. Use #12 or #14 wood screws. See
illustration.
• Screws must penetrate at least one inch into vertical
wall studs.
• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille
panel and reach into the opening at the back to grasp
the power cord. Pull the power cord into the opening
as you push the refrigerator back.
• Gently push refrigerator into the opening with hands
against front corners.
Brackets
Required
IMPORTANT NOTE: When the refrigerator is installed under a soffit
or if there is not enough height for this method of security, brackets
cannot be used. Proceed to step 5 to level the refrigerator and then
to step 6 to secure refrigerator to cabinets. The refrigerator must be
secured to prevent tipping.
Block
Height
From
Floor
Bottom
of Wood
Block
Side View
2 x 4 Cut
35" Length
Installation
Height
From Floor
Screws Mounted into
Vertical Wall Studs
Soffit
to
Mounting
Bracket
Brackets
Not Required
Beneath a
Soffit
Installation
Stud
Spacer
Block
Refrigerator
Cabinet
Door
36" Stainless Steel Refrigerators, Freezers
Step 5
Level
Refrigerator
These products have a 4-point leveling system. The
front is supported by leveling legs, the rear is supported
by wheels.
• Adjust rear wheels beneath the product to just barely
touch the 2x4 block.
• Turn the 7/16" hex nut located above the front wheels.
Turn to raise or lower.
• For front leveling legs, use a 1-1/4" open-end wrench.
• Adjust carefully; the product should be level and
plumb with cabinetry, and should align with toekick
height.
CAUTION
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator more
than 1", you will damage the front leveling legs and
rear leveling wheels.
Hex Nut Adjusts
Rear Wheels
Leveling Leg
PRUDENCE
Les roues de nivellement arrière et les pattes de
nivellement avant permettent un réglage maximal
de 25 mm (1 po). Si l’ouverture pour le réfrigérateur
a une hauteur supérieure à 2,15 m (84-1/2 po),
l’installateur doit élever le réfrigérateur sur une
feuille de contre-plaqué ou des glissières. Il est
également possible d’ajouter des baguettes de
finition des placards sur le haut de l’ouverture afin
de la réduire. Lever le réfrigérateur de plus de 25 mm
(1 po) endommage les pattes de nivellement avant
et les roues de nivellement arrière.
Step 6
Secure
Product
to Sides
NOTE: Whenever possible, perform
this step for additional anti-tip
security. This step can be used as
an alternate to Step 4, Anti-Tip
bracket installation, whenever
brackets cannot be used.
When using 1/2" to 3/4" side panels, the front flange of
the case trim is attached to the side panel.
• Open door to access case trim.
• Drill hole in trim below interior opening. Drive screw
through trim and side panel.
• Follow the same procedure on opposite side.
OR
If installed between cabinets with no side panels or in
a custom enclosure, install a spacer block as shown.
• Open door to access case trim.
• Drill hole in trim below opening. Drive screw through
trim and into block.
• Follow the same procedure on opposite side.
11
Installation
Screws
Top Case Trim
Raise To
Installation
Height
36" Stainless Steel Refrigerators, Freezers
Step 7
Connect
Freezer
Water Supply
Step 8
Check Power
• Locate and bring tubing to the front of the cabinet.
• Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a
bucket, then shut off water.
Copper Tubing:
• Slip a 1/4" nut and ferrule (provided) over both ends
of the copper tubing. Insert tube into the union fitting
on the unit and tighten nut to union.
• Turn on the water to check for leaks.
GE SmartConnect™ Tubing:
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression
nut until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
NOTE: Make sure excess tubing length does not
interfere with toekick installation.
• Check to make sure power is on by opening the door
to see if interior lights are on.
Step 9
Mount Top
Grille Panel
For shipping purposes, the top case trim is secured at
84" installation height.
To raise case trim to 84-1/2" installation height or to
lower case trim to 83-1/2":
• Loosen 2 screws on both sides and raise or lower the
top case trim to meet soffit height or to the top of
adjacent cabinets.
• Tighten all 4 screws.
• Mount the grille panel by dropping into slots on the
case trim.
The grille panel assembly is factory set for an 84"
installation height. If installation height is 83-1/2" or
84-1/2", order ZGCSS36RH (right hand) or ZGCSS36LH
(left hand) grille panel kit.
1-1/2"
min.
gap
IMPORTANT: Maintain 1-1/2" min. gap between top of doors and
bottom of grille panel.
12
Installation
Door Should be Parallel
With Grille Panel
Bushing
D
o
o
r H
in
g
e
C
a
s
e
H
i
n
g
e
5/16" Wrench
Raise
Pin Shoulder
36" Stainless Steel Refrigerators, Freezers
Step 10
Adjust Door
Alignment
Step 11
Install
Toekick
Step 12
Temperature
Controls
Check door alignment. The top of the door should be
parallel with the grille panel. If the door appears to be
too high or too low on the handle side, adjustments
can be made by turning the hinge.
• To raise the door, turn adjustable hinge pin toward
the right.
• To lower the door, turn hinge pin toward the left.
Turn the hinge pin with a 5/16" wrench or, on some
models, use the 3/16" Allen wrench taped to the hinge.
• A standard toekick is supplied. Install with 2 screws
provided, adjust to desired height and tighten screws.
IMPORTANT: The vented toekick must remain
unobstructed for proper air circulation and operation.
• Set temperature control at “5”.
IMPORTANT: Allow 24 hours for temperatures to stabilize
before making adjustments.
Step 13
Start
Icemaker
Problem Solving
• Start the switch to I (on). The green light will come on
• Be sure nothing interferes with the sweep of the
• Discard the first few batches of ice cubes.
• To turn the icemaker off, set the switch to O (off).
Operation of Refrigerator and Freezer
If the product does not operate after checking the
installation instructions:
• Check to be sure power cord is plugged in the wall
• Check to be sure that fuse or circuit breaker is
If any of these problems persist:
Call for Monogram local service in your area,
1.800.444.1845.
and the icemaker will begin operation automatically.
feeler arm.
Allow 45 minutes for the icemaker to resume
operation.
outlet.
turned on.
Power Switch
Feeler Arm
Green Power Light
Cleaning the Stainless Steel Exterior
Stainless Steel has some unique cleaning
characteristics. In order to keep your refrigerator or
freezer looking like new, we suggest cleaning it with
Stainless Steel Magic
Stainless Steel Magic
Home Depot, Servistar, HWI and other leading stores.
It is also available through GE Parts by calling
1.800.626.2002. Order part number WX10X15.
or a similar product.
is available at Ace, True Value,
13
ZUGSS Trim Kit
Unified Stainless Steel Custom Grille Panel
Step 1
Install
Spacer Pads,
Replace
Side Case Trims
Tools and Materials Required:
• #1 and #2 Phillips screwdrivers or sockets
• 1/4" angled wrench and 1-1/2" open ended
wrench
• Drill and appropriate bits
• Custom grille panel
• Safety glasses
• Gloves to protect against
sharp edges
D
E
B
C
Parts List:
A. Soffit Vent Top
F
B. Left Side Case Trim
C. Right Side Case Trim
D. Center U-Shape Trim
E. Grille Base Wrap
F. Stainless Steel Unified Panel
G
G. Foam Spacer Pads
CAUTION: Handle parts with care to avoid scratching.
In a side by side installation, the inside case trim of both
products will be removed and replaced with a shorter
trim.
• Lift up to remove the supplied grille panel assembly on
both products. Discard both assemblies.
Completion Time: Allow approximately 3 hours to install
this kit.
IMPORTANT: 2 People are required to install this kit.
CAUTION: Disconnect power before you begin.
A
14
Foam
Spacer
Pads
• Apply the supplied foam spacer pads to the mating
side of one product as shown.
• Remove the Phillips head screws from the inside case
trim of each product as shown. Remove and discard
side trim. Retain screws.
• Install new side case trim with notches toward the
bottom. Install with original screws.
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Step 2
Install
Anti-Tip
Brackets
WARNING
ANTI-TIP PRECAUTIONS
These products are heavy at the top and must be
secured to prevent the possibility of tipping over.
ATTENTION
PRECAUTIONS CONTRE LES BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut et
il faut le maintenir en place pour éviter la possibilité
de son basculement vers l’avant.
• Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4
mounting brackets provided using #12 or #14 wood
screws.
• Secure the brackets with wood block to the back wall
so that it is 84" (or your installation height) from the
finished floor. Use #12 or #14 wood screws. See
illustration.
• Screws must penetrate at least one inch into vertical
wall studs.
Roll Both Products into Opening
• Gently push each product into opening with hands
against front corners. Push back into the opening until
it is flush or semi-flush with adjacent cabinets.
Brackets
Required
IMPORTANT NOTE: When the products are installed under
a soffit or if there is not enough height for this method of
security, use Step 4 as an alternative. The refrigerator and
freezer must be secured to prevent tipping.
Block
Height
Bottom
of Wood
Block
Side View
2 x 4 Cut
71" Length
Installation
Height
From Floor
Screws Mounted into
Vertical Wall Studs
Soffit
From
Floor
to
Mounting
Bracket
Brackets
Not Required
Beneath a
Soffit
Step 3
Level Both
Products
Both products MUST BE LEVEL AND PLUMB with each
other and adjacent cabinetry on each side. Toekick
heights should align with cabinetry.
• Adjust carefully. Both models have 4-point leveling.
The front is supported by leveling legs, the rear is
supported by wheels.
• Raise units to the same level, aligning with adjacent
toekick heights.
• Adjust rear wheels beneath the product to just barely
touch the 2x4 block.
• Turn the 7/16" hex nut located above the front wheels
to raise or lower the back of the refrigerator.
• To adjust the front leveling legs: Use a 1/4" angled
wrench to turn the top of the leveling leg, or turn the
bottom of the legs with a 1-1/4" wrench.
CAUTION
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator
more than 1", you will damage the front leveling
legs and rear leveling wheels.
Hex Nut Adjusts
Rear Wheels
Leveling Leg
Units must be 1" apart and evenly aligned at top and
bottom. The inside case trims must align, top and
bottom.
PRUDENCE
Les roues de nivellement arrière et les pattes de
nivellement avant permettent un réglage maximal
de 25 mm (1 po). Si l’ouverture pour le réfrigérateur
a une hauteur supérieure à 2,15 m (84-1/2 po),
l’installateur doit élever le réfrigérateur sur une
feuille de contre-plaqué ou des glissières. Il est
également possible d’ajouter des baguettes de
finition des placards sur le haut de l’ouverture afin
de la réduire. Lever le réfrigérateur de plus de 25 mm
(1 po) endommage les pattes de nivellement avant et
les roues de nivellement arrière.
15
ZUGSS Trim Kit
Case Trim
U-Shape
Trim
Grille Base Cover
Unified Stainless Steel Grille Panel
Step 4
Secure
Products
To Sides
Step 5
Install Center
Trim Strip
NOTE: This step can be used as
an alternative to Step 2, Anti-Tip
bracket installation, whenever
brackets cannot be used.
Whenever possible, perform
this step for additional anti-tip
security.
When using 1/2" to 3/4" thick side panels, the front
flange of the case trim is attached to the side panel.
• Open door to access case trim.
• Drill hole in trim slightly below the interior opening.
• Drive screw through the trim and into the side panel.
• Follow the same procedure on the opposite outside
product trim.
• Open doors fully.
• Starting at the top, press trim strip over inside case
trims of both products.
• Continue pressing trim until you reach the bottom of
the case trims. The trim will align with the top and
bottom of the case trim.
Refrigerator
Stud
OR
If the product is installed between cabinets with no
side panels or into a custom enclosure, install a spacer
block as shown.
Cabinet
Door
Spacer
Block
Step 6
Remove
Wire Fence and
Switch Cover
16
Remove
3 Screws
• Remove 3 screws holding the wire fence on both
products. Retain fences and all screws.
• Lift off grille base covers. Discard covers.
Step 7
Install
Grille Base
Cover
ZUGSS Trim Kit
Unified Base Cover
• Open doors fully.
• Install the double width grille base cover by slipping
the notched ends over the hinges.
Unified Stainless Steel Grille Panel
Place
Trim Over
Hinges
Step 8
Remove
Grille Frame
Install
3 Screws
• Place wire fence over the grille base cover (textured
side out). Drive original wire fence screws through the
fence, the grille base cover and into the frame.
Remove
Screws
• Back out 2 screws on each side of the top case trim.
• The top piece is secured to the unit with a rubber dust
gasket. Roll the trim upward to access and remove
end screws as shown. Remove and discard inside
pieces.
• Slide assembly out of the rubber gasket.
Install
3 Screws
Remove
Screws
Remove
Screws
Dust
Gasket
17
ZUGSS Trim Kit
Unified Stainless Steel Grille Panel
Step 9
Install
Soffit
Vent Top
Slip Dust Gasket
Into Trim On One End
• Separate the top and hinge side trim pieces by
removing side screws. Discard top piece; retain
screws.
• Install one end piece to unified top piece with
2 original screws.
• Slip end of rubber dust gasket into end of top unified
piece and slide trim towards the center. Engage the
second piece of gasket and continue sliding trim until
even with opposite ends.
• Reinstall end pieces to case trims. Push top piece up
against soffit or to installation height. Tighten screws
on both sides.
• Whenever possible, place a level on the top trim.
Adjust side trims until entire grille frame is level.
Slip Second Dust
Gasket Into Trim
Reinstall
Screws
Step 10
Mount
Unified
Grille Panel
• Mount the unified grille panel by dropping into slots on
the outside case trim.
18
Step 11
Adjust
Door
Alignment
ZUGSS Trim Kit
Raise
Pin Shoulder
Check door alignment. The top of the door should be
parallel with the grille panel. If the door appears to be
too high or too low on the handle side, adjustments can
be made.
• Use a 5/16" wrench to turn the hinge.
• To raise the door, turn adjustable hinge pin toward
the right.
• To lower the door, turn hinge pin toward the left.
Bushing
D
o
o
r H
C
a
s
e
H
5/16" Wrench
Unified Stainless Steel Grille Panel
in
g
e
i
n
g
e
19
Pub. No. 49-60073-3
Part No. 197D3003P001
12-03 JR
65161-01
Note: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Loading...