GE ZGU364LDP5SS, ZGU364LDP6SS, ZGU364LRP4SS, ZGU364LRP5SS, ZGU364NDP5SS Installation Guide

...
Installation
Instructions
36" and 48"
Professional Rangetops
Tables de cuisson
professionnelles de 36" (91 cm)
et de 48" 1122 cml
Instructions d'installation
Estufas profesionales
de 36" (91 cm)y 48" (122 cm)
Instrucciones de instalaci6n
Lo secci6n en espafiol empieza en Io p6gino 28
131-i0S141
06-i0 GE
Safety Information
BEFORE YOU BEGIN
Reod these instructions completely ond corefully.
"IMPORTANT- Savetheseinstructionsfor
local inspector's use.
"IMPORTANT-Observeallgoverning
codes and ordinances.
, Note to Installer- Be sure to leave these
instructions with the Consumer.
, Note to Consumer - Keep these instructions
with your Owner's Manual for future reference.
, Completion Time- 1to 3 hours. , Proper installation is the responsibility of
the installer. Product failure due to improper installation is not covered under the warranty. See
Owner's Manual for warranty information.
AWARNING
This appliance must be properly grounded. Follow directions in"ElectricSupply"of this manual.Failureto do so
may result in electric shock. For Monogram local service in your area,
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.5544.
For Monogram Parts and Accessories, call
1.800.626.2002.
If you received a damaged rangetop, you should contact your dealer.
In the Commonwealth of Massachusetts: , This product must be installed by a licensed
plumber or gas fitter.
, When using ball type gas shut off valves, they
shall be T-handle type.
, A flexible gas connector, when used, must not
exceed 3 feet.
Vent hood Combinations:
It is recommended that these rangetops be installed
in conjunction with a suitable overhead vent hood.
, Install a hood with at least 1200 CFM above a 48"
wide rangetop.
, Install a hood with at least 600 CFM above a 56"
rangetop.
Due to the high heat capacity of this unit, particular
attention should be paid to the hood and ductwork installation to assure it meets local building codes,
AWARNING:
Clearancesto horizontalsurfaces abovethe range, measured to the cooking surface are below. Failureto
comply may result infire hazard.
, Installations without a hood require 48" minimum
to combustibles.
, A custom hood installation with exposed
horizontal combustibles surfaces must hove an Auto-On feature.
, For other installations with a hood, refer to hood
installation instructions for specific hood clearances.
ACAUTION:
These rangetops are extremely heavy. Due to the weight and size of the rangetop and to reduce the
risk of personal injury or damage to the product:
TWO PEOPLEARE REQUIRED FOR PROPER
INSTALLATION.
Installation must conform with local codes. In the
absence of local codes, the rangetop must comply with the National Fuel Gas Code, ANSIZ225.1/
NFPA 54, latest edition and National Electrical Code ANSI/NFPA 70 latest addition. In Canada, installation must conform with the current Natural Gas
Installation Code, CAN/CGA-B149.Z or the current
Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This rangetop has been design-certified by CSA International according
to ANSI Z21.1, latest edition and Canadian Gas Association according to CAN/CGA-Z.1 latest edition.
Leak testing of the appliance shall be conducted according to the manufacturer's instructions.
Design Information
CONTENTS
Design Information
Models Available ......................................................................3
Backsplash Accessories .......................................................3
Product Dimensions and Clearances
for 48" Wide Models ...............................................................4
Product Dimensions and Clearances
for 36" Wide Models ...............................................................5
Installation Options ...............................................................6
Installation Preparation
Tools and Materials Required ...........................................7
Power Supply Locations .....................................................7
Remove Packaging .................................................................8
MODELS AVAILABLE
Monogram rangetopsarefactorysetfornatural
gas.Order themodel foryour installationsituation.
48" Natural Gas Models: ZGU484NG - 4 gas burners, grill and griddle
ZGU486NR- 6 gas burners and grill ZGU486ND - 6 gas burners and griddle
Installation Instructions
Step 1, Cut the Countertop Opening ..............................9
Step 2, Install the Rungetop ............................................10
Step 3, Connect Rungetop to Gas ................................10
Step 4, Connect Electrical .................................................11
Step 5, Check Burners .......................................................11
Finalize Installation ..............................................................11
Installation Checklist ...........................................................11
Install the Rangetop Backsplash Accessory ............12
Install the Adjustable
Bocksplosh Accessory ................................................13, 14
36" Natural Gas Models: ZGU364ND - 4 gas burners and griddle
ZGU364NR- 4 gas burners and grill ZGU366N - 6 gas burners
BACKSPLASH ACCESSORIES
All models require 12" minimum clearance to a vertical combustible surface at the rear.
If clearance is less than 12", the entire surface
of the back wall above the countertop and the full width of the rangetop must be protected by a
backsplash. The backsplash must be constructed
of non-combustible material, such as metal, ceramic tile, brick, marble or other stone.
Two Backsplash Accessories Available:
The 12" high stainless steel backsplash accessory is available. Use this backsplash in combination
with a custom, non-combustible backsplush built
beyond the 12" height. The combined height of the bucksplush accessory and the custom backsplash must reach the bottom of u hood,
or when there is no hood, to 48" above
the cooking surface.
An adjustable 30" to 36" high backsplash with shelf is also available. This backsplash fills in the space between the top of the rangetop and the bottom
of the hood. The shelf is positioned so that
heat lamps from the bottom of a Monogram professional hood are directed towards the shelf.
12" High Backsplash
ZX12B48PSS,for 48" wide rangetops ZX12BB6PSS,for 56" wide rangetops
30"to 36" Adjustable Height
Backsplash With Shelf
ZXADJB/48PSS,for 48" wide
rangetops
ZXADJB36PSS,for 36" wide
rangetops
Design Information
PRODUCT DIMENSIONS AND CLEARANCES FOR 48" MODELS
47-7/8" Width _ _ Front of
.................__ _u,,nose
AWARNING:
Installations without a hood require 48" minimum to combustibles
above the rangetop. A custom hood installation with exposed horizontal
combustible surfaces must have an Auto-On feature. Refer to hood
installation instructions for specific hood clearances.
The surface of the entire back wall above the countertop and below
the hood must be covered with a non-combustible material such
as metal, ceramic tile, brick, marble or other stone.
.._ 27-1/2" to
Height
13"
Min.
-_/2"
48" Minimum to Combustibles
46-1/4"
22-3/4" Min.
Locate gas inlet on back
wall or on floor 2" from back wall.
-- EachSide
Universal Utility Locations
\
\
\
\
12" Minimum to
Adjacent Wall
12" Minimum
7/8"
* The opening between a 4" high backsplash must be 48" to allow the rangetop to slide back against the wall.
ADDITIONAL CLEARANCES: Allow 12" minimum clearance to an adjacent wall on
each side. Working areas adJacent to the rangetop should have
18" minimum clearance between countertop and the bottom of the wall cabinet.
12"Minimum to Combustibles or 0" to non-combustible material above the
cooking surface
--Clearanc
o
48" Min. to
Combustibles
Design Information
PRODUCT DIMENSIONS AND CLEARANCES FOR 36" MODELS
,,d 27-1/2" to
35-7/8" Width ..............L _ Front of
......................... _--_ "- aullnose
.,......... .
AWARNING:
Installations without a hood require 48" minimum to combustibles
above the rangetop. A custom hood
installation with exposed horizontal
combustible surfaces must have an Auto-On feature. Refer to hood
installation instructions for specific hood clearances.
The surface of the entire back wall above the countertop and below
the hood must be covered with a non-combustible material such
as metal, ceramic tile, brick, marble or other stone.
13" Max.
8-1/2"
Height
18" Min.
l
48" Minimum to Combustibles
F
35"
22-3/4" Min.
O
Universal Utility Locations
Locate gas inlet on back
wall or on floor 2" from back wall.
combustible 12"Minimum
' EachSide
36"
12" Minimum to
Adjacent Wall
1/2"
2-1/2"
* The opening between a 4" high backsplash must be 36" to allow the rangetop to slide back against the wall.
ADDITIONAL CLEARANCES: Allow 12" minimum clearance to an adjacent wall on
each side.
Working areas adJacent to the rangetop should have
18" minimum clearance between countertop and the bottom of the wall cabinet.
5
12"Minimum to
Combustibles or 0" to
non-combustible material above the
cooking surface 48" Min. to
Combustibles
Clearanc
0" -I
INSTALLATION OPTIONS
Design Information
-,I.....................................................................................................................................28-13/18" ..................................................................................... _,-
8"
Countertop 8-1/2"
Level Height
Backedge of chamfer
* Minimum cabinet cutout depth from
the back of the rear trim to the back finished edge of the control panel -
typically, the minimum cabinet depth
(front to back). Maximum cabinet cutout depth is 26" minus the countertop
overhang.
ToFront ofControl Knobs
27-1/2" ........................................................................................................................................
ToFrontof Bullnose
\
/
Finished back edge of control panel
23-1/2 _,-
** 26" .........................................................D,.
26-3/4" .................................................................................................................................................
TOFront of Control Panel
t Includethe overhung ofthe rear trim when countertop continuesbehindthe product. Theoverhung isdecorativeonly.Theweight of the rungetop isfully supported by thesidetrims.
\ ! 'J I
8-1/2"_:: _D,-
5-1/4" '_
7-1/4"
** Maximum countertop cutout depth from the buck of the rear trim
to the buck edge of chamfer at the sides of the control panel - typically,
the maximum countertop cutout depth ffront to buck). Minimum countertop cutout depth is25-1/4".
1/2"
Countertop
Level.........
_, t3/32"
.......1-3/16"
1-1/32"
ToPipeStub Center
Rangetop
1/2" Above Adjacent
Countertops
Control panel projects forwards from standard depth cabinets.
Rangetop
1/2" Above Adjacent
Countertops
Front of deep cabinets can align with control panel beveled edge.
Installation Preparation
TOOLS REQUIRED
Saber Saw
Measuring Tape
Carpenter's Square
Safety Glasses
Phillips #2
Screwdriver
Level
Drill and
Appropriate Bits
Adjustable Wrench
1/4" Driver or
Wrench
Hand Truck
MATERIALS PROVIDED
Hold-Down Regulator
Strap
MATERIALS REQUIRED (not provided}
Joint Pipe Fittings Shut-Off
Sealant Valve
5-foot maximum length, 5/8" O.D. CSA-approved
flexible metal gas supply
(3-foot maximum length in Massachusetts only)
NOTE: Purchase new flexible line; do not use
previously used flexible gas line.
POWER SUPPLY LOCATIONS
Gas Supply:
The natural gas models are designed to operate at 5" water column pressure. For proper operation, the
pressure of the natural gas supplied to the regulator must be between 7" and 13" water column.
Locate the pipe stub on the back wall or floor (see"Product Dimensions and Clearances"). Use S-foot
maximum length, 5/8" O.D.flexible gas supply line
(3-foot in Massachusetts).
Install a manual shut-off valve in the gas line (not provided), in an easily accessible location. Make sure the homeowner knows where and how to shut off the gas supply to the rangetop.
Electric Supply:
These rangetops must be supplied with 120 volt, 60 Hz.,
and connected to a dedicated, properly grounded branch circuit protected by a 15 amp circuit breaker or time
delay fuse.
The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard
three-prong grounding wall receptacle to minimize the
possibility of shock hazard from this appliance. If the electrical service provided does not meet the above
specifications, it is recommended that a licensed electrician install an approved outlet.
DO NOT,UNDERANY CIRCUMSTANCES,CUT
ORREMOVETHETHIRD (GROUND)PRONGFROiVl
THE POWERCORD.
DO NOTUSEAN EXTENSION CORDWITHTHISAPPLIANCE.
Locate the electric supply within the area shown or
within reach of the rangetop's four-foot power cord.
To avoid tangling cord with items stored inthe cabinet,
locate the receptacle on rear wall, inside the cabinet.
ReceptacleBoxCoverPlate....
ThreeProngPlug
"\
__ihr Pr n R t
Installation Preparation
REMOVE PACKAGING
ACAUTION
Stand dear. The ends of the cut metaJ banding may snap toward you.
,Cut the metal banding. ,Remove packaging tape and foam.
Dispose of packaging materials properly.
,Cut the ties holding the grill grate to the grill frame.
Griddle Flue Cover
,Remove grill/griddle covers, grill grate and burner
grates.
,Lift out cast-iron griddle flue cover, grease
troughs and pads.
Ties Grease Troughs
, Lift off burner caps and remove foam pad,
then lift off burner heads and remove foam pad.
Remove Foam Pads ......
Installation
STEP 1
Allow Additional
ClearanceBelow
the RangetopBurner
Boxfor the Regulator
andGasConnections
48" wide models are designed to fit in 48" or wider base cabinets
CUT THE COUNTERTOP OPENING
Avalable, .} 30"
asn ............ ,, to36"
BackSpl 12 I
Measure carefully when cutting the countertop. Make sure sides of the opening are parallel.
Allow 8" free space below the top surface of the countertop.
Allow additional clearances below the burner box to install the regulator and make house supply
connections. Use a 90° elbow to route the gas connections and limit interference with drawers
or other cabinetry features.
These rangetops are designed to hang from the countertop by their side flanges.
Smooth any rough edges on the countertop before installing the rangetop.
- Formica countertop edges must be finished.
The countertop must be strong enough to support the weight of the rangetop.
Allow Additional
ClearanceBelow
the RangetopBurner
Boxfor the Regulator
andGasConnections
56"widemodelsare designedto fit in 56"or wider basecabinets
Cutout Opening with False Bottom
Dimensions
A (Oia.) B C O 56"Rangeto 7-3/8" 1-1/2" 7-1/2" ii-i/8" 48"Rangeto 8-1/4" 1-1/2" 7-1/2" 11-1/8"
You can construct the cutout with a false bottom to conceal the bottom of the rangetop.
- Build the false bottom using a solid material; cut a
7-1/2" x 11-1/8" hole in the left rear corner for the gas inlet and power cord clearances.
Installation
STEP 2 INSTALL RANGETOP
,Slide the rangetop into the opening. Make sure
the rangetop is evenly seated and supported.
,A hold-down strap with screws is provided to
secure the rangetop to the rear or side cabinet walls.
, Remove the hold-down strap from the back
of the rangetop. Attach one end of the strap to the back of the rangetop.
,Secure the other end of the strap as high as
possible to the cabinet back wall or adjacent cabinet. Keep the strap as short as possible for better security.
STEP 3 CONNECT RANGETOP TO GAS
AWARNING
4
Back Wall
Hold-Down Strap
Location and
Attachment
Do not use a flame to check for gas leaks.
A manual shut-off valve must be installed where it will be accessible.
Assure that gas is turned off at the shut-off valve.
, Install the supplied pressure regulator onto the end
of the gas inlet.
,You can install a 90 ° elbow (not provided) onto the
gas inlet and route the gas connections to avoid interference with drawers or other cabinetry
features. However, it is not recommended because it will result in a drop in gas pressure.
,Make sure the regulator is installed in the right
direction. See arrow on the underside of the
regulator.
NOTE: Instead of using solid piping to connect
to pressure regulator, an approved flexible metal
appliance connector may be used between the pipe stub and the shut-off valve to the pressure regulator, if local codes permit.
.Turn on gas and check for leaks:
-Use a liquid leak detector at all joints and connections in the system.
RangetopBurnerBox
\\\\\\.
1/2" N.RT.
GasInlet
Regulator
(Supplied)
Ii l SolidPiping
IMPORTANT: Disconnect the rangetop and the individual shut-off valve from the gas supply piping system during any pressure testing of that system at test pressures greater than 1/2 psig. Isolate the rangetop from the gas supply piping system
by closing the individual manual shut-off valve to the rangetop during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.
or Flexible Connector
Shut-0ff
Valve
PipeStubFrom HouseGasSupply
10
Installation
STEP4 CONNECT ELECTRICAL
, Plug power cord into properly grounded
receptacle.
, Press the button on the left side of the control
panel. The lights above the knobs should
illuminate.
STEPS CHECK BURNERS
Check to be sure that burner heads and caps are securely seated.
Burner Cap ProperlySeated
Burner Cap Not Properly Seated
FINALIZE INSTALLATION
Place the burner grates over the burners. The grates should be seated and should not rock.
The griddle is secured with screws. It is designed to be stationary and should not be removed.
The griddle has two leveling screws beneath the rear flue cover that can be used to adjust to the desired slope.
Griddle Flue Cover
,Check for proper ignition:
- Push in one control knob and turn to LITE position.
- The igniter will spark and the burner will light;
the igniter will cease sparking when the burner
is lit.
- First test may require some time, while air is flushed out of the gas line.
- Turn knob to OFF.
- Repeat the procedure for each burner.
IMPORTANT: If the igniter electrodes continue to spark after the burners are lit, check that each burner component is assembled properly.
Refer to the Owner's Manual.
,Burner flames should be blue and stable with no
yellow tips, excessive noise or lifting of the flame
from the burner. If any of these conditions exist, check that the burner ports are not blocked. If one of these conditions continues, call for
service.
The two inner screws are clamping screws for securing the griddle in place. Loosen these two screws before leveling. Do not remove these two
screws. The two outer screws are leveling screws. Do not
remove these two screws. They can be turned to level the griddle or to provide a forward slope to help grease and oils to drain away from the food being cooked.
After leveling the griddle, hand-tighten the clamping screws; do not over-tighten.
INSTALLATION CHECKLIST
[] Hake sure all controls are left in the OFF
position.
[] Hake sure the flow of combustion and
ventilation air to the rangetop is unobstructed.
[] The serial plate for your rangetop is located
on the bottom of the rangetop. In addition to the model and serial numbers, it tells you
the ratings of the burners and the type of fuel and pressure the rangetop was adjusted
for when it left the factory.
[] Recheck Steps:
Double check to make sure everything in this manual has been completed. Rechecking
steps will ensure safe use of the rangetop.
11
ZX12B30PSS,ZX12B36PSS,ZX12B48PSS AccessoryInstallation
OPTIONAL ACCESSORIES--12" HIGH BACKSPLASH
AWARNING:
To prevent ignition of combustible materials,
the entire back wall above the range must
be protected by a backsplash constructed
of non-combustible material.
This stainless steel backsplash accessory
must be installed in combination with a custom,
non-combustible backsplash built beyond
the 12" height of the backsplash.
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
iMPORTANT: Save these instructions for local inspector's use. IMPORTANT: OBSERVE ALL GOVERNING CODES
AND ORDINANCES. NOTE TO iNSTALLER: Be sure to leave these
instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions
with your Owner's Manual for future reference.
INSTALL 12" BACKSPLASH
A WARNING: Thisbacksplashmust
be securely fastened to the wall. Failure to do so could result in damage or personal injury.
, Install and level the range or rangetop and the range
hood according to the installation instructions.
, Remove the backsplash packaging and
protective film.
, Use a level to pencil a horizontal line on the wall, 1/8"
above the range or rangetop. The 1/8" gap allows the cover panel to overlap the wall support panel.
, Locate wall studs on each side. Where studs are not
available, plan to use wall anchors (not provided).
,Align the wall support panel on the marked
horizontal line and centered left to right.
,The wall support panel must be secured to the wall
at all 4 corners. Use wood screws (provided) or wall anchors (not provided) to secure the support panel
to the wall.
, Place the cover panel over the wall support
panel and secure with Torx screws (provided). Install 2 screws on each side.
This kit provides for the installation of a 12"
high backsplash for 30", 36" or 48" Monogram Professional Ranges and Rangetops.
TOOLS AND MATERIALS REQUIRED
,Gloves to protect against sharp edges
,T-15 and #2 Phillips screwdrivers Wall Support
,Drill with 3/32" and 9/64" bits Panel
,Safety glasses
, Level
,Pencil This Kit Includes
,Wall support panel
,Cover panel
, Hardware package with
- 5 Stainless Steel Torx 15 #8 self-tapping screws
- 5 Phillips #2 pan head wood #10 screws
Hardware
Package
!/8"
Wall Support
Panel
Install 4
Wood Screws
Wall Support Panel
Cover Panel
12
Loading...
+ 28 hidden pages