GE W4L Specification Sheet

WALLIGHTER 400 LUMINAIRE
W4L25S0A
1
SN4
DB
F
APPLICATIONS
•  Underpasses, loading docks and building perimeter security
•  Applications where a high wattage wall mounted  luminaire is needed
SPECIFICATION FEATURES
•         /   1598 Listed
Suitable For Wet Locations
•  Sealed and charcoal ltered housing
•  Die-cast aluminum housing protected       inside  and out with dark bronze polyester     powder paint  nish
•  ALGLAS® nish on aluminum reector
•  Heat and impact resistant prismatic       glass  refractor
ORDERING NUMBER LOGIC
•  Pre-wired terminal board and         integral  direct-mounted ballast
•  .75 in. (19mm) NPT conduit       entrances  sides and top
•  Photoelectric receptacle available
•  Mogul base E39 socket standard     except 150W PMH medium base socket
•  Magnapack packaging available
The  Energy  Independence  and  Security  Act  of  2007  (EISA)  aects  Metal  Halide  (MH)  and  Pulse  Metal  Halide  (PMH) wattages from 175W to 450W and for domestic usage, the new digit is “E = EISA-compliant PMH” which  has a minimum  eciency of 88%. In many cases, the lumen value  and lamp life of a lesser wattage meets or  exceeds the former MH ballast/lamp system. For 175W applications, where 175W E-PMH is not available, 150W  PMH may be an acceptable substitute. 150W PMH is medium base socket unless otherwise listed or requested.
PRODUCT IDENT
XXX
W4L = Wallighter 400
WATTAGE
XX
15 = 150 17 = 175 20 = 200 25 = 250 32 =320 35 = 350 40 = 400
X
Energy
E = Act Compli­ant Pulse MH (EPMH) S = HPS M = MH P = PMH
Standard: Lamp not included.
VOLTAGE
X
60Hz 0 = 120/208/
240/277
Multivolt 1 = 120 2 = 208 3 = 240 4 = 277 5 = 480 C = 120/240/ 277 D = 347 T = 220
50Hz 6 = 220 Y = 240
BALLAST TYPE
X
See Ballast and Photometric Selection Table
A = Autoreg
G = Mag-
Reg with Grounded Socket Shell
H = HPF Reactor
or Lag
K = Hot Restart
M = Mag-Reg
N = NPF Reactor
or Lag
P = CWI with
Grounded Socket Shell
PE FUNCTION
X
1 = None 2 = PE Receptacle
NOTE: Receptacle connected same voltage as unit. Vertical mounting only. Order PE Control separately.
IES DISTRIBUTION TYPE
XXX
See Ballast and Photometric Selection Table
SN4 = Short, Non-cuto,
Type IV
COLOR
XX
DB = Dark
Bronze
OPTIONS
XXX
B = Time Delay
Automati­cally Switched Quartz
F = Fusing (Not
available with
multivolt) L = Latch on door S = External
Sliptter for
1-1/4 inch
(32mm)
diameter Pipe
Mounting Ø48=External
Sliptter for
2 in. (51mm)
diameter pipe
mounting
A-82/2008
GE Lighting Systems, Inc.
www.gelightingsystems.com
FIXTURE DIMENSIONS
WALLIGHTER 400 LUMINAIRE
DATA
Approximate Net Weight 27-45 lbs 12-20 kgs
Eective Projected Area 1.5 sq ft max 0.15 sq M max
BALLAST AND PHOTOMETRIC SELECTION TABLE
All light sources are clear unless otherwise indicated.
Ballast Type/Voltage
IES Light Multi- 120, 208, Distribution Wattage Source volt 240, 277 347 480 220 220 240 Type
150 (55V)  HPS  H,N G,H,K,M,N H,M,N M N/A N/A H,M SN4  9714 200, 250,
400  HPS  A A,P A, P A,P A A A SN4  9664 150  PMH  H* H H N/A N/A N/A N/A CF  CF
250,320  EPMH  A A N/A N/A N/A SN4  9713 350, 400  EPMH  A A
CANADA & EXPORT ONLY
175, 250
  MH  A A A A A A A SN4 9713
400  MH  A A, P A, P NOTE: N/A = Not Available. 
CF = Contact Factory.   * = 120X240X277
60Hz 50Hz
A
N/A N/A N/A SN4  9665
A,P
N/A CF CF SN4  9665
Photometric Curve Number 35-17 - - - -
REFERENCES 
See Page A-97 for start of Accessories.  See Page A-101 for Explanation of Options and Other Terms Used.
GE Lighting Systems, Inc.
www.gelightingsystems.com
2008/A-83
Loading...