All moisture probe calibrations are
traceable to the National Institute of
Standards and Technology (NIST).
Installation Flexibility
for OEM Applications
The rugged, compact VeriDri transmitter is designed specifically for OEM
installations where space is at a premium. It can be installed directly in the
process stream or, if necessary, in a
sample system. If required, GE can
design and build a sample conditioning system to meet the unique
application demands.
The VeriDri transmitter is available
with OEM pricing for a minimum
quantity of 10 units. Discounts on larger
quantities are also available, and blanket
orders are accepted.
Specifications
Moisture Ranges
• –110° to 20°C
• –110° to –50°C
• –80° to 20°C
• –80° to –30°C
• –30° to 20°C
• –60° to 40°C
• –150° to 70°F
• –150° to –40°F
• –40° to 70°F
• –100° to 0°F
• –50° to 50°F
•0°to 100°F
•0 to 10 PPMv
•0 to 100 PPMv
•0 to 1,000 PPMv
•0 to 10,000 PPMv
Note: PPMv ranges based on constant
pressure, provided at time of order
placement.
Operating Temperature
–40° to 60°C (–40° to 140°F)
Storage Temperature
70°C (158°F maximum)
War m-Up Time
Meets specified accuracy in three
minutes
Accuracy
• ±2°C from –65° to 40°C dew/frost
point
• ±3°C from –80° to –66°C dew/frost
point
Repeatability
•±0.5°C from –65° to 40°C dew/frost
point
•±1.0°C from –80° to –66°C frost
point
Response Time
Less than five seconds for 63% of a
step change in moisture content in
either wet-up or dry-down cycle
Electrical
Power
•7 to 28 VDC (loop-powered, customer supplied)
• Output:
4 to 20 mA
• Output Resolution:
0.01 mA
• Max Loop R = 50x(PSV-7) ohms
(Where: PSV = Power Supply
Voltage)
Example:
Given a 24 VDC Power Supply,
Max Loop R = 50 x (24 - 7)
= 850 Ω
• Cable:
2 m., standard (consult factory for
custom lengths)
Mechanical
Sample Connection
3
/
4-in. 16 straight male thread with
O-ring
Operating Pressure
5 µ Hg to 5,000 psig (345 bar)
Enclosure
NEMA 4X/IP67
Dimensions
• Overall: 6.76 × 1.13 in. diameter
• Electronics with cable: 4.08 × 1.13
in. diameter
•Weight: 5 oz. (140 grams)
European Compliance
Complies with EMC Directive 89/336/
EEC and PED 97/23/EC for DN<25
Moisture Sensor
Sensor Type
Thin-film aluminum oxide moisture
sensor probe
Calibration
Each sensor is individually computer
calibrated against known moisture
concentrations, traceable to NIST
Calibration Interval
Sensor recalibration at GE Infrastructure
Sensing is recommended every six to 12
months depending on application
Flow Rate
• Gases: Static to 10,000- cm/s linear
velocity at 1 atm
• Liquids: Static to 10- cm/s linear
velocity at density of 1 g/cc
GE Infrastructure
Sensing
T 800 833 9438 • 978 437 1000
F 978 437 1031
sensing@ge.com
www.gesensing.com
All specifications are subject to change for product improvement without notice. Panametrics®is a registered trademark of Panametrics, Inc. GE®is a
registered trademark of General Electric Co. Windows
®
is a registered trademark of Microsoft Corporation, which is not affiliated with GE, in the U.S. and
other countries. Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective companies,
which are not affiliated with GE.
VeriDri transmitter dimensions in inches (cm)
3/4-16 UNF-2A
2.68
(6.81)
1.13
(2.87)
2.58
(6.55)
1.50 (3.81)
Minimal Cable
Bend Allowance
Power and
Measurement
Circuits
+
7-28VDC
4-20mA
_
“Loop-Powered”
Blue
Brown
VeriDri wiring diagram