
GE
ROADWAY LIGHTING
g
Lighting Solutions
GUIDE FORM SPECIFICATIONS
VERSAFLOOD ® II SIGNLITER
GENERAL DESCRIPTION
The NEMA heavy-duty weather-resistant floodlight designated
_______ (identify) shall be a GE VERSAFLOOD® II SIGNLITER,
ordering number _______ (specify V2FN or V2FS, plus ordering
number logic from catalog) or approved equal, to operate one
_______ (specify [70, 100, 150(55V), 200, 250 or 400] watt high
pressure sodium [HPS] or [(175, 250 or 400) watt metal halide
or mercury]) lamp from a nominal _______ (specify 120, 208,
220, 240, 277, 347 or 480) volt , 60 Hz or 240 volt, 50 Hz power
source and shall be capable of starting and operating the
specified lamp within the limits specified by the lamp manufacturer. The luminaire shall include a completely prewired integral
ballast and an optical assembly with _______ (specify MN4 or
SN4 according to photometric selection table) IES Distribution
type. The luminaire shall have a NEMA lamp identification decal. It shall be UL/cUL Listed SUITABLE FOR WET LOCATIONS.
Standard construction is IP55.
MECHANICAL CONSTRUCTION
The luminaire shall include a die-cast aluminum housing and
hinged front door frame with stainless steel latch, brace to hold
door open for relamping, ballast, lamp socket, filtered optical
assembly, surface mounting through back, 3/4 -inch threaded
(with screw-in plugs) conduit openings (for wiring) on top and
sides of housing, tempered door glass (and optional prewired
photoelectric control receptacle). All hardware shall be corrosion-resistant . All die-cast aluminum surfaces shall have an
electrocoat _______ (specify dark bronze [standard] or gray)
paint finish.
BALLAST OPERATION
OPTICAL ASSEMBLY
The optical assembly shall be sealed, have an activated
charcoal filter, and include a precision formed aluminum
reflector stippled, heat/impact-resistant tempered flat
door glass (on V2FS 400-watt units, use convex glass), with
gasketing around the perimeter of the housing. The reflector
shall have a chemically bonded and lightweight non-breakable
ALGLAS
providing corrosion resistance, durability and ease of cleaning.
The optical assembly shall contain an E39 mogul base socket
with superior lamp gripping. The socket shall have added insulation, giving it the ability to handle the higher pulse ratings of
newer HID systems. The socket shall be capable of field adjustment for variations in beam spread without parts modification
or replacement and with no more than a screwdriver for a tool.
®
finish on both the inside and outside surfaces
All electrical components shall be mounted on the housing.
The ballast shall be prewired to the lamp socket and terminal
board. There shall be a plug-in igniter for use with HPS lamps.
The luminaire shall contain a standard _______ (specify) type
ballast* in full compliance with lamp-ballast specifications
available from lamp manufacturers at time of manufacture.
The ballast shall reliably start and operate the lamp in ambient
temperatures down to -20
-40°F for HPS.
The luminaire and ballast shall be from the same manufacturer.
°
F for mercury and metal halide and
* REFER TO PRODUCT PAGE FOR OTHER BALLAST SELECTIONS.
FOR MORE DEFINITIVE INFORMATION, REFER TO BALLAST SPECIFICATIONS IN TECHNICAL DATA SECTION.
Guide Form Specifications – 2011

g
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 6 9 4 3 5 3 3- - -- 8 8 8
GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.