GE PSB42LSR User Manual

PSB42LSR – GE Profile™ 42" Built-In Stainless Side-By-Side Refrigerator
42" Frame-to-Frame
Depth Including
Handles 26-7/8"
41"
Case Width
25-3/8" Case Depth
*81-3/4"
at Rear
*84" From
Floor to
Top Frame
130° Door Swing 90° Door Swing
B
A
23-7/8" Behind Frame
C
D
D
with Electronic Dispenser
Dimensions (in inches)
* Shipping height
* The front height may be
adjusted from 83-1/2" to 84-1/2" by adjusting front and rear leveling legs a maximum of 1".
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped doors and grille panels, and beveled edges. These models are shipped ready for installation.
Product Clearances
These refrigerators are equipped with a 2 position door stop. The factory set 130° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Models A B C D 42" 12-3/16" 16" 24" 4"
Allow minimum clearances for Freezer door (Dimension A) and Fresh Food door (Dimension B) for a full 130° door swing and to allow for drawer removal.
Four inch (4") minimum clearance is required when door swing is adjusted to 90°. If the 90° door stop position is used, drawer access is maintained, but drawer removal is restricted.
Specification Revised 1/06
210319
Listed by Underwriters Laboratories
Total volume and shelf area are calculated by the Association of Home Appliance Manufacturers’ standards.
For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service,
800.626.2000.
PSB42LSR – GE Profile™ 42" Built-In Stainless Side-By-Side Refrigerator
with Electronic Dispenser
The Installation Space
*The finished cutout width must be: 41-1/2" for 42" models
Water and Electrical Locations
The opening must be prepared with the electrical and water supply located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent cabinets, depending on your installation.
Additional Specifications
• A 120 volt, 60Hz, 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
• Water line can enter the opening through the floor or rear wall. The water line installed should be 1/4" O.D. copper tubing or GE SmartConnect™ tubing between the cold water line and water connection location. The line should be long enough to extend to the front of the refrigerator. Installation of an easily accessible shutoff valve in the water line is required.
Specification Revised 1/06
210319
Side Panels
Side panels (not supplied) must be used whenever the sides of the refrigerator will be exposed.
* Depending on
installation height.
Flooring
For proper installation, this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator, or approximately 1500 lbs.
NOTE: Protect the finish of the flooring. Cut a large section of the cardboard carton and place under the refrigerator where you are working.
Listed by Underwriters Laboratories
Total volume and shelf area are calculated by the Association of Home Appliance Manufacturers’ standards.
Grounding the Refrigerator
IMPORTANT—Please read carefully
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
The power supply cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.
For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service,
800.626.2000.
Loading...
+ 1 hidden pages