GE PSB2200NBB01, PSB2200NBB02, PSB2200NWW01, PSB2200NWW02, PSB2201NSS01 Installation Guide

Installation
Instructions

Advantium ®240V

Built-ln SpeedCook
Ovens

PSB2200

PSB2201
ZSC2200
ZSC2201
ZSC2202

49-40574-1

MFL06213302

02-08 JR

Safetg Information

BEFOREYOU BEGIN

Read these instructions completely and carefully.

IMPORTANT- savetheseinstructionsfor

local inspector's use.

IM PORTANT- Observe allgoverningcodes

and ordinances.

• Note to Installer - Be sure to leave these
instructions with the Consumen

• Note to Consumer - Keep these instructions
with gour Owner's Hanual for future reference.

• Skill Level - Installation of this appliance

requires basic mechanical and electrical skills.

• Completion Time - 1 Hour.

• Proper installation is the responsibilitg of the

installer. Product failure due to improper
installation is not covered under the warrantg.

See Owner's Manual for warrantg information.

IMPORTANT- Use this oven onlg for

its intended purpose. Never use the oven for
warming or heating a room. Prolonged use of the

oven without proper ventilation can be hazardous.

CAUTION:

For personal safety, remove house fuse or oven

circuit breaker before beginning installation to
avoid severe or fatal shock injurg.

CAUTION:

For personal safetg, the mounting surface must

be capable of supporting the cabinet load, in
addition to the added weight of the 80-pound oven

and 30-pound drawer, plus additional oven loads of
up to 50 pounds or a total weight of up to 160

pounds.

CONTENTS

Design Information

Models Available ......................................................................2

Product Dimensions and Clearances ............................3

Tools and Parts Required ....................................................3

Parts Supplied ..........................................................................3

Electrical Tools and Parts Required ................................3

Advance Planning ..................................................................3

Installation Preparation

Electrical Requirements ......................................................../4

Install Junction Box ................................................................/4

Preparing the Opening (Installation without

an accessorg storage drawer) ..................................5%

Preparing the Opening (Installation with

an accessorg storage drawer) ..................................7-8

Installation Instructions

Step 1, Remove Packaging and Parts ..........................9

Step 2, Route Conduit ........................................................10

Step 3, Install Bottom Trim ..............................................11

Step/4, Install Mounting Screws ....................................11

Step 5, Finalize Installation ..............................................11

MODELS AVAILABLE

Profile Models:
PSB2200NWW-White

PSB2200NBB-Black
PSB2201NSS-Stainless Steel

Monogram Models:

ZSC2200NWW-White
ZSC2200NBB-Block

ZSC2201NSS-Stainless Steel

Monogram Pro Range Models:

ZSC2202NSS-Stainless Steel

NOTE:This unit cannot be installed with an

accessorg storage drawer.

CAUTION:

For personalsafetg, this product cannot be

installed in cabinet arrangements such as an
island, a peninsula or below a countertop.

2

Design Information

PRODUCT DIMENSIONS AND CLEARANCES

_21-1/2"_

\

\

\

\

,,

TOOLS AND PARTS REQUIRED
(NOT SUPPLIED}

[] #2 Phillips screwdriver
[] Hand held drill

[] High speed drill bit, 3/32"diameter
[] 3/8" slot head screwdriver

[] Level
[] Saw

[] 2x_ or 2x2 lumber for installing runners

or 3/8" plywood for floor (if required)

[] Wood screws or other hardware for installing

runner or shelf to support oven (if required)

[] Safety glasses or goggles

PARTS SUPPLIED

[] 6 brass screws (3 required, 3 extra)
[] 5 color matched screws (4 required, 1 extra)

[] Bottom trim

ELECTRICAL TOOLS AND PARTS

REQUIRED (NOT SUPPLIED)

[] Junction box
[] Electrical cable (3-conductor or t-conductor wire

as required by local codes)

[] UL-listed conduit connectors
[] Wire cutters and wire strippers

NOTE: Appearance will vary by model.

29-3/4" "1

[ O 11

19"

J Yy

ADVANCEPLANNING

• These ovens may be installed directly into a 30" wide
oven cabinet.

• Cutout dimensions are NOT the same for installation
with or without an accessory storage drawer. Hake

sure to use the correct cutout when preparing the
opening.

NOTE: Model ZSC2202 CANNOT be installed with an

accessory storage drawer See Installation

Preparation Without an Accessory Storage Drawer

for this model.

IMPORTANT-Thisoven is not approved for

use above another built-in Advantium Speedcook

oven, a side by side installation or below a
countertop.

• For personal safety, this oven cannot be installed
in a cabinet arrangement such as an island or
peninsula.

• The oven must be installed at least 36-3//4" above
the floor.

• Allow for clearance to adjacent corners, walls,
drawers, etc.

• Cabinets installed adjacent to wall ovens must

have an adhesion spec of at least 194°F

temperature rating.

The oven must be securely installed in a cabinet
that is firmly attached to the house structure.

Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to

climb, sit, stand or hang on the oven door.

If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into

the cabinet. See the Accessor_l Storage Drawer

Assemblg Instructions.

3

Installation Preparation

ELECTRICALREQUIREMENTS

Single Speedcook Installation
Product rating is 120/208 or 120/240 volt, 60 Hz,

30 amps. This product must be connected to a supply
circuit of the proper voltage and frequency and

protected by a time delay fuse or circuit breaker.
Power should be supplied from a separate, dedicated

30-ampere branch circuit. Wire size must conform to
the requirements of the National Electrical Code or the

prevailing local code.
Combined Speedcook and Wall Oven Installation

When installed in combination with a GE/Honogram
single wall oven, use separate electrical junction boxes.

Refer to single oven installation instructions for
electrical requirements of that product.

These connections must be made by a qualified
electrician. All electrical connections must meet

National Electrical Code or prevailing local codes.

Combined Speedcook and Warming Drawer

Installation

INSTALLJUNCTION BOX

The conduit is located at the top right on the back of
the oven.

Locate and install thejunction box within reach of the

oven conduit.

• Through the left or right sides of the cabinet wall
and into adjacent cabinet.

• Or, through the cutout floor.

• Or, in the upper cabinet.

1-

Cutout
Height

b

When installing the 8peedcook oven over a GE or
Honogram electric warming drawer, a separate 120V,

60Hz, properly grounded receptacle must be installed.
See instructions packed with the warming drawer.

WARNING

• The electrical power to the oven branch circuit
must be shut off while line connections are being

made.

• Use copper wiring only.

• Electrical ground is required on this appliance.

The free end of the green wire {ground wire)

must be connected to a suitable ground.

This wire must remain grounded to the oven.

• If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or other

insulating materials, DO NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEUTRAL or

GROUNDING circuit could result in an electrical
shock.

• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly

grounded.

Failure to follow these instructions could result in
serious injury or death.

4

Installation Preparation

PreparationWITHOUTanAccessorgStorageDrawer

PREPARE THE OPENING

The Advantium 240V can be installed in
combination with other GE/Monogram appliances.

Always follow each product's Installation

Instructions to complete the installation.

Single Advantium 24OV Installation:
Order a 30" wide single oven cabinet or cut the

opening in a wall to the dimensions shown.

30" • 23-1/2"

4- 25-1/4" "

17-1/2"

L_

J

36-3/4"

Min.

J

J

• Always maintain 36-3/4" minimum height from
the floor to the cutout in any single or combined

installation.

• Allow 2-1/8" case trim overlap on the sides and
7/8" overlap on the bottom of the opening for all
models. Allow 1-1/4" case trim overlap on the top

for models PSB2200 and PSB2201 and 3//4"
overlap on the top for models ZSC2200, ZSC2201

and ZSC2202.

• Oven overlaps will conceal cut edges on all sides
of the opening.

When installed over a single oven or a warming
drawer, allow at least 2" between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.

Construct
Base
Min. 3/8"

..\Plywood

Supported
by2x4 or 2x2

Runnersall
FourSides

PREPARE THE OPENING (CONT.)

Installation over a GE/Monogram

Warming Drawer:

23-1/2"

NOTE: Additional clearances between the cutouts

may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming

Drawer installation instructions for details.

Construct
Solid Bottom
Min. 3/8"

Plywood
Supported
by2x4or2x2

J Runnersall

FourSides

2" Min.

_ (3" recommended)

g

drawer
requirement

Construct a solid oven floor of 3/8" min. thick pluwood
supported bu 2 x 4 or 2 x 2 runners on all sides.

• The support must be level and rigidlu mounted,
flush with the bottom edge of the cutout.

S