GE PEB3228RMSS Installation Instructions
Installation
Instructions d’installation
Finishing sets for built-in
Microwave Oven
Instructions
Questions? Call 1-800-561-3344 or visit our Website at: GE Appliances.ca
?
BEFORE YOU BEGIN
Read these instructions completely and carefully
IMPORTANT – Save these instructions for
•
local inspector’s use.
IMPORTANT – Observe all governing
•
codes and ordinances.
Note to Installer – Be sure to leave these
•
instructions with the Consumer.
•
Note to Consumer
the future reference.
Skill level – Installation of this appliance requires
•
basic mechanical and electrical skills.
• Installation time – 1 - 3 hours
• The installer is responsible for the quality of the
installation.
• Product failure due to improper installation is not
covered under the Warranty.
• This set is CUL approved for installation alone or in
combination with a single GE or GE profile electric
built-in oven.
Do not alter or modify any parts of this set or any
•
parts of the oven.
• For easiler installation and your own safety, we recom
-mend that the installation of this microwave oven
be done by two people.
• Unplug the microwave oven before beginning insta
-llation of this set.
– Keep these instructions for
Series PEB3228
PARTS INCLUDED
PART QUANTITY
NOTE
technician from wasting time looking for a
replacement screw if he lost one of them during
the installation.
WARNING – This oven must be connected to
a properly grounded three-pronged 120V outlet, as
required by the National Electrical Code.
Trim kit
frame
Bottom duct
Rails 2
Inlaid
Short screws
Long wood
screws
: This set includes extra screws to prevent
1
1
1
14
(11 + 3 extra)
6 – painted
(4 + 2 extra)
For your safety
WARNING
off the power at the distrubition board and block the circuit
breaker to prevent the power from being accidentally reset.
If it is not possible to block the circuit breaker, put a warning
clearly visible, as a label on the switch board.
Before starting the installation, switch
–
Installation Instructions
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Measuring tape
Pencil
Phillips screwdriver
Tools and Parts
Drill
7/64” drill bit
Parts Supplied (not shown to scale)
Trim kit frame
The insulating strip
Bottom duct
Short screws (14)
(11 + 3 extra)
Rails (2)
Long wood screws
(6 - painted) (4 + 2 extra)
Location Requirements
The microwave oven may be installed over a built-in oven. If installing
over a built-in oven, make sure there is a minimum of 3” (7.6 cm)
between the top of the lower oven cutout and the microwave oven
The microwave oven may also be installed in a cabinet by itself (without
a built-in oven below). For best usability, we recommend a minimum
Make sure the surrounding cabinetry has clearance to open and close
freely. Allow a clearance of at least 1 9/16 “ (4. 0cm) below the cutout
of at least 2” (5.1 cm) above the cutout opening.
2”
(5.1 cm)
1
9/16“
(4.0 cm)
36”
(91.4 cm)
2”
(5.1 cm)
3”
(7.6 cm)
Required Cutout Dimensions
3/4
22
”
(57.8 cm)
17” (43.2 cm)
min.
1/8” (43.5 cm)
17
max.
3”
(7.6 cm)
NOTES:
Height dimension is critical: 17” (43.2 cm) minimum, 17
(43.5 cm) maximum.
Width and depth measurements have ±1/16” (2 mm)
tolerance.
3” (7.6 cm) minimum dimension is from lower oven cutout
Trim kit frame extends 1
cutout opening.
26
” (66.8 cm)
11/32
A. Trim kit frame overhang
B. Cutout for lower oven
1/16
“ (2.7cm) above and below the
Trim Kit Frame Dimensions
7/8
26
” (68.2cm) *
3/4
” (75.6cm) **
29
26” (66.1 cm)
“
19 1/11
(48.5 cm)
2/5” (1.05 cm)*
17/8 (4.75 cm)**
* 27“ (68.6 cm) trim kit
** 30“ (76.2 cm) trim kit
2 3/5 “
(7.25 cm)
13
(34.0 cm)
3/16”
1
(3.0 cm)
1
1/16”
(2.7 cm)
1/16
1
”
(2.7 cm)
1/8”
2/5“
A. Upper cabinet
B. Microwave oven cutout
C. Lower oven cutout
D. Lower cabinets
E. Floor
EN-2
Installation Instructions
Electrical Requirements
WARNING
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, re, or
electrical shock.
Install according to all local governing codes and ordinances.
Required:
A 120 volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a
fuse or circuit breaker.
Recommended:
A time-delay fuse or time-delay circuit breaker.
A separate circuit serving only this microwave oven.
Electrical Shock Hazard
GROUNDING INSTRUCTIONS
For all cord connected appliances:
The microwave oven must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of electric
shock by providing an escape wire for the electric current. The
microwave oven is equipped with a cord having a grounding wire
with a grounding plug. The plug must be plugged into an outlet
that is properly installed and grounded.
WARNING: Improper use of the grounding plug can result in a
risk of electric shock. Consult a qualied electrician or serviceman
if the grounding instructions are not completely understood, or
if doubt exists as to whether the microwave oven is properly
grounded.
Do not use an extension cord. If the power supply cord is too short,
have a qualied electrician or serviceman install an outlet near the
microwave oven.
SAVE THESE INSTRUCTIONS
Prepare Microwave Oven
Attach Rails
1. Unplug microwave oven before proceeding with installation.
2. Remove any loose items inside microwave oven.
3. Carefully turn microwave oven onto its top, with the door facing
forward (toward installer).
4. Align the two rails on the microwave oven bottom, as shown,
making sure the anges are forward and pointing up.
A. Rails (2)
B. Microwave oven bottom
C. Short screws (4)
5. Secure the rails to the microwave oven bottom using four short
screws.
Stick the Insulating Strip
1. Carefully return microwave oven to its upright position.
2. Stick the insulating strip to the louver on the enclosure to avoid
the heat releasing from the louver
D. Flanges
E. Door
EN-3
A. The insulating trip
B. Enclosure
Loading...