GE JV374, JV474, JV674 Use and Care Manual

Use and Care of

Ventilati~

,

,,

,

m

‘-nywgetymr

*

Rm it

~dfi~ *h*ian

: in@lation

* Have inswr

‘“ ctit b-r

‘-

w~

*

Dwto ti

is M
@e

inking

m.,~he,~ fm h

Hood

,

,

Modekm74, W474

new hood...

instied

instructions,

your

to avoid

and properly grounded by

in

show

or

&se

accotice

you the

and mark it @r easy

with

l~ation of the

hd...

hood h drawing-r, special

spreadhg

surface

of your range.

your w

of possible

ml

tm

th$

hood

xnce.

Oame froti

-mtilyifit=--shmtakvethe
a~

quired
@identi

‘Wrthis reaaon:

-Never hve snrfaceutits
wtiw, Eodover

overs Mat may

o~rating.

use

~~• settings ordy

~M

on surtie

well-fitting

DQN~USEWATER

NEVER

WYOUM

BURNED, immediately turn off
hood switches. M

@t

Flami&grease outside pancanbe extinguished by

baking
chemical or foam type extinguisher,

-Nmr me f- mder
* opm$kg

-~hoodti

kmruction$ to

~ ‘

grease fires.

top.

While the

to prevent

cooking fires

fan is operating, caution is

the

starting and spreading of

wtie the

vent fan is in

mattended at

causes smoking and greasy

ignite and spread if vent fan is

To

*i*

adquate stid utensds

~matic fm

operation,

and use high heat

when necessary.

the

mut

of a

g-e -,

sm~her fl-

unit by cover@ pan completely with

tid, cookie sheet

or

flat

tray.

ON GREASE

PICK

UP A

DO SO

FL-O

PAN.

W~HOUT GETT~G

surface

there

is danger of being burned,

wtil AFTER

soda,

flame

has been reduced.

or, if available, a multi-purpose dry

the hood

tith

because it may spread the flames.

me Wrs

clean

according to

maintain good venting and to

m hqt

unit

the

8

caution

on

W.

spiii-

pfi

~S.

ti

vent

avoid

&

N674

Write down the model and serial numbers.

You’ll find them on a label on the left inside wall of the
hood. These numbers are also on the Consumer Product
Ownership Registration Card that came with your hood.
Before sending in this card, please write these numbers
here:

Model Number

Use these numbers in any correspondence or service
calls concerning your hood.

I

LABEL

Your hood is equipped with two grease filters.
When the fan is operated, air is drawn through the two

filters and discharged to the outside.

CAUTION-before operating the hood:

●

Remove the tape that holds the grease filters in place

during shipment.

●

Remove the lamp shield, install the lamp bulbs (not

provided), and replace the lamp shield. See on page 2.

firn

page for Operating and

Serial Number

LAMP SHIELD

GREASE

FILTERS

Cleaning imtructiom.

A Quality Product of GENERAL ELECTRIC COMPANY

To Operate

Care and Cleaning

BLOWER CONTROLS.

the blower on and off. An infinite-speed slide
lets you select blower speed. Setting “l” provides
lowest speed, “6” provides highest. When the blower
goes off, the blower speed control stays at the selected
setting until you reset it.

N

‘J

‘

[n]

v

(.

I

[m]

LIGHT CONTROL.

lets you turn the light on and off. First position turns
on both bulbs for normal
turns off the left-hand
the other one is a 25-watt bulb, you have a night light

system. Third position turns both bulbs off.

,LowE:pEED[q]

ON

A slide control lets

LIGHT

A three-position slide control

lighting.

bulb~so i~it’s

Second position

a 75-watt bulb and

you

turn

;ontrol

I

GREASE FILTERS.

clean filters. Frequency of cleaning
type of cooking you do, but GREASE FILTERS
SHOULD BE CLEANED AT LEAST ONCE A
MONTH.

To remove:

recess at top of
filter out and (3) remove filter.

To

solution. Brush lightly to remove
Rinse, shake and remove moisture before replacing.

To replace:

grasp tab, fit filter into channel and swing it into place.

Never operate hood without filters in place.

Grasp filter tab and (1) lift filter up into

clean:

Soak and then agitate in a hot detergent

With filter tab toward outside and bottom,

Hood efficiency depends on

depen-ds

filter

channel, (2) swing bottom of

imbedded soil.

on the

w.,

To install bulbs:

removing fuse or switching circuit breaker off. Press
sides of flexible lamp shield to release the locking tabs
and allow the shield to swing down. After installing
bulbs, push lamp shield up and press sides until tabs
lock into slots above. Then reconnect power to hood.

Do not install bulbs rated higher than 75 watts.

CAUTION:

removing. A warm or hot bulb may break if

touched with a moist cloth or hand.

\-l.

Disconnect power to hood by

Let the lamp cool completely before

\ ,

7

HOOD.

warm detergent solution. Use a mild detergent solution
to clean

CLtiH;

POWDERS. Vacuum blower to clean it—never
immerse it in water.

Clean grease laden surfaces frequently with a

Dainted

CAUTION:

bulb with either a moist cloth or wet hand. A
warm or hot lamp bulb may break if touched
with a moist surface. ALWAYS let lamp cool
COMPLETELY before cleaning around it.

surfaces. DO NOT USE ABRASIVE

STEEL WOOL PADS, OR SCOURING

Be certain you do not touch lamp

2