You’llfind them on a label on the back wall of the
hood.
These numbers are also on the Consumer Product
Ownership Registration Card that came with your
hood. Before sending in this card, please write
these numbers here:
Whenyougetyourn%whood. . .
Have itinstalledandproperlygroundedin accord-
ancewiththe InstallationInstructionsbya
qualifiedtechnician.
Havethe installershowyouthe locationof the
hoodcircuitbreakerorfuse,and markit for easy
referenca
Dotake thetime to read oursuggestionsfor
bestusa
Whenusingyourhood. . .
Dueto the hoodfan drawingpower,special
cautionis needed to avoidspreadingofpossible
flamefromthe cookingsurfaceofyour range.
Neverleavesurface unitsunattendedat high heat
settings Boilovercausessmokingandgreasy
spilloversthat may igniteand spreadif hoodis
used Use surfaceunit heat settingsrecommendedbymanufacturerandadequate-size
utensils
DO NOT USEWATERON GREASEFIRES.
NEVER PICK UPA FLAMING PAN.Smotherflam-
ingpanonsurfaceunitbycoveringpancornpletelywith well fitting lid cookie sheet orflat tray,
and,IF YOU CAN DO SO WITHOUT GEITING
BURNED,immediatelyturn“OFF’ the surface unit
switchand hood.If there isdangerof being
burned,wait untilAITER flame has’been reduced.
Flaminggreaseoutsidepan can be extinguished
bybakingsoda or,if available,a multi-purposedry
chemicalor foam type extinguisher.-
If you need service.. .
e Don’tattemptto repairor replace any partofyour
hoodunlessit is specificallyrecommendedin this
book All othersetvicingshould be referredto a
qualifiedtechnician.
@Disconnecthoodcircuitbreakeror fuse before
performingany service.
Model Number
Serial Number
Use these numbers in any correspondence or ser-
vice calls concerning your hood.
#
GREASE FILTER
Your hood is equipped with a metal grease filter.
When the fan isoperated, air is drawn through the
filter and discharged to the outside.
CAUTION: Before operating the hood:
Remove the Grease Filter. (See instructions on
page 2.)
Removethe wrappings from the filter.
Install the lamp bulb (not provided). See Lamp
Replacement instructions on page 2.
Reinstall the Grease Filter. The hood must not
be operated without the filter in place.
LAMP COVER
(~OddSJV324J, d!/334J,
/
/
JV$24J, JV634J)
clip to remove
fiiter.
D
4t
d
. .+=ti.
w..- W..,L
w.
.6 .
ToOperate
LAMP SWITCH
‘FM SVWK3-1
LampSwitch
FormodelsJV322 and JV332, switchhas OFF
and ON positions.For other models,CENTER
positionOFF, LEFT positionNIGHT LIGHT, RIGHT
positionBRIGHT LIGHT.
FanSwitch
CENTER positionOFF, LEFTpositionSLOW
SPEED, RIGHT positionHIGH SPEED.
To Maintain
GreaseFilter
The efficiency of your hooddepends on a clean
filter. Frequency of cleaning depends on the type
of cooking you do. BUT GREASE FILTER
SHOULD BE CLEANED AT LEAST ONCE
A MONTH. NEVER OPERATE THE HOOD
WITHOUT THE FILTER IN PLACE.
To remove: Pressoutward on spring clip, pull
down and snap out filter.
To clean: Soak and then agitate in a hot detergent
solution. Light brushing may be used to remove
imbedded soil. Rinse, shake and remove moisture
before replacing.
Withcarefulhandling,thefilterwill lastforyears,
If replacementbecomesnecessary,orderpart
numberWB2X2052from yourdealer.
To replace: Put the filter rim in and against two
clips, push outward on the third clip and press
filter upward into place.
Hood
Clean grease laden surfacesof the hood frequently. Use warm detergent solution. About
1tablespoon of ammonia may be added to the
water. TAKE CARE TO NOT COME IN CONTACT
WITH FILTERS AND OTHER NON-ENAMELED
SURFACES. The hood shell can be washed, rinsed
and dried with a soft cloth.
Motor and Fan
To Clean Motor and Fan
1. DISCONNECT THE HOOD POWER SUPPLY
AT THE HOUSEHOLD DISTRIBUTION PANEL
BY REMOVING THE FUSE OR SWITCHING
OFF THE CIRCUIT BREAKER.
2. Remove filter.
3. Wipe fan blade and motor with cloth, dampened
only in ammonia and warm water solution.
The lampcoverneed notbe
removedforlamp removalor
installation.
“-<CAUTION:‘Letlamp.cool coinpletelybefore
removing.-Awarmorhot bulb maybreak if
touchedwith a moistcl?th or hand.
Remove lamp and replace with an ordinary screwbase lamp bulb NOT MORE THAN 60 WATTS.
To remove lamp cover, if desired:
e Pressthe sides with two fingers until the side
prongs are released.
● Lift lamp cover and slide towards you in one
motion.
To replace lamp covec
e
Insert prong located at end of cover into top
opening.
●
Gently push cover up and presssides to fit side
prongs into the side openings.
o
Release and the cover will lock in position.
m
e
CAUTION: Be certainwhencleaninghood “
surfacesyoudo nottouchlamp bulbwith
moisthandsor cloth.A warm or hotlamp
bulb. maybreak if touchedwith a moistsurface.ALWAYSlet lampcool COMPLETELY
beforecleaningaroundit.
BeforeYouCM for Service
If the fan does not operate when the switch is
on, check the hood power supply at the household distribution panel. A fuse may be blown or
a circuit breakertripped.
If the fan fails to circulate air, possible causes
such as the fan blade striking the hood shell or
excessivelysoiled filter should be checked and
corrected before using the hood again.
If the fan operates but moves air slower than
normal, check to besure the filter is clean. If
that does not correct the problem, call for
service.
If the fan keeps going off and on, the motor is
probably overheating and turning itself off. This
can be harmful to the motor. Check to be sure
the filter isclean. If off and on cycling continues, call for service.
purchase,wewillprovide,free of
charge,partsandservicelaborin
yourhometorepairorreplaceany
parfof thehood thatfailsbecause
of manufacturingdefect.
——
———
Thiswarrantyisextendedto the
originalpurchaserandanysucceedingownerforproductspurchased
forordinaryhomeusein the 48
mainlandstates,Hawaiiand
Washington,0.C. InAlaskathe
warrantyisthesameexceptthat it
is LIMITEDbecauseyoumust pay
to shiptheproducttotheservice
shopor fortheservicetechnician’s
travelcoststo yourhome.
Ail warrantyservicewillbeprovided
byourFactoryServiceCentersor
byourauthorizedCustomerCare@
servicersduringnormalworking
hours.
Lookin theWhiteorYellowPages
of yourtelephonedirectoryfor
GENERALELECTRICCOMPANY,
GENERALELECTRICFACTORY
SERVICE,IGENERALELECTRICHOTPOINTFACTORYSERVICEor
. Failureof the productif it is
usedforotherthanits intended
purposeorusedcommercially.
@Damage to productcaused
byaccident,fire,floodsor acts
of God.
WARRANTORIS NOT RESPONSIBLEFORCONSEQUENTIAL
DAMAGES.
-
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.