GE HSS25ATHBCBB, GZS22DSJCFSS, GZS22DSJBFSS, GZS22DMJCFES, GZS22DMJBFES Owner’s Manual

...

GEAppliances.com

Safety Instructions.................2-3

Operating Instructions

Automatic Icemaker .................. 12,13

Care and Cleaning ................... 15,16

Crispers and Pans ....................... 11

ExpressChill _M, ............................ 5

Ice and Water Dispenser ................ 14

Refrigerator Doors ...................... 10

Replacing the Light Bulbs ............. 16,17

Shelves and Bins ....................... 8, 9

Temperature Controls .................... 4

TurboCool _M, ............................. 5

ClimateKepper2 .......................... 5

Water Filter .............................. 7

Installation Instructions

Installing the Refrigerator ............ 23-26

Moving the Refrigerator ............. 19-22

Preparing to Install

the Refrigerator ......................... 18

Water Line Installation .............. 27-29

Troubleshooting Tips ............ 31-33

Normal Operating Sounds ............... 30

Models 22, 23, 25,26,27 and 29

Cote a Cote

Refr rs

Lc_section frc_nqcuse commence 2_Ic_pc_ge 40

Lado a Lado

Lc_seccion en e.spc_ho/ empieze_ en Ic_pc)ginc_ 75

4..-

Consumer Support

Consumer Support ............. Back Cover

Data Sheets ............ 34,35

Warranty ............................... 36

Write the model and serial numbers here:

Model #

Serial//

Find these numbers on a label inside the

refrigerator compartment at the top on the right side,

200D8074P051 49-60646-4 10-14 GE

IMPORTANT SAFETYINFORMATION. READALL INSTRUCTIONSBEFOREUSING.

GEApp//ances Webs/te

For more information on your refrigerator's operation, visit www, GEAppliances.com or

call 800, GECARES {800, 432,2737), In Canada visit GEAppliances.ca or call 800, 567, 3344,

REFRIGERATOR SAFETY INFORMATION

A This is the safety alert symbol, This symbol alerts you to potential hazards that can kill or hurt you and others, All safety messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION", These words are

defined as:

Indicates a hazardous situation which if not avoided, will result in death or serious injury,

Indicates a hazardous situation which if not avoided, could result in death or serious injury,

_lndicates a hazardous situation which if not avoided, could result in minor or moderate injury,

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your refrigerator follow these basic safety precautions:

This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used,

Unplug the refrigerator before making repairs, replacing a light bulb, or cleaning, Note: Power to the refrigerator cannot be disconnected by any

setting on the control panel,

Note: Repairs must be performed by a qualified service professional,

Replace all parts and panels before operating, Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance,

Becauseof potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord,

However,ifyou must use an extension cord, it is absolutely necessarythat it be a UL-listed(in the United States)or aCSA

certified (inCanada),3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical

rating of the cord be 15 amperes (minimum) and 120 volts,

To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator before disposing of it or discontinuing its use,

Do not allow children to climb, stand or hang on the door handles or the shelves in the refrigerator, They could seriously injure themselves,

IMPORTANT SAFETY INSTRUCTIONS

I__ o reduce the risk of injury when using your refrigerator, follow these basic

Do not clean glass shelves or covers with warm water Do not touch the cold surfaces in the freezer compartment when they are cold, Glass shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping or dropping, Tempered glass is designed to shatter into many small pieces if it breaks,

, Keep fingers out of the "pinch point" areas; clearances

between the doors and between the doors and cabinet are necessarily small, Be careful closing doors when children

are in the area,

safety precautions,

when hands are damp or wet, skin may stick to these extremely cold surfaces,

Do not refreeze frozen foods which have thawed

completely,

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism, or with the heating element that releases the cubes, Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in,

INSTALLATION

_ Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. result in fire, explosion, or death.

CONNECTING ELECTRICITY

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet Do not remove the ground prong

[Do not use an adapter [Failure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

OEAppliances, corn

Failure to do so can

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance,

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded,

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall outlet, Do not use an adapter,

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating

that matches the rating plate,

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required, This provides the best

performance and also prevents overloading house wiring circuits which could cause a fire hazard from

overheated wires, Never unplug your refrigerator by pulling on the power

cord, Always grip plug firmly and pull straight out from the outlet,

Repair or replace immediately all power cords that have become frayed or otherwise damaged, Do not

use a cord that shows cracks or abrasion damage along its length or at either end,

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord,

PROPERDISPOSAL OF YOUR OLD REFRIGERATOR

Suffocation and child entrapment hazard. Remove fresh-food and freezer doors from the refrigerator, prior to disposal. in child entrapment which can lead to death or brain damage.

IMPORTANT:

Child entrapment and suffocation are not problems of the past, Junked or abandoned refrigerators are

still dangerous even if they will sit for ':just a few days," If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent accidents,

Before You Throw Away Your Old Refrigerator or Freezer:

Take offthe fresh food and freezer doors, Leave the shelves in place so that children may

not easily climb inside,

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior

to product disposal, If you are getting rid of an old refrigeration product, check with the company

handling the disposal about what to do,

Failure to do so can result

READANDFOLLOWTHISSAFETYINFORMAT/ONCAREFULLX

SAVE THESEINSTRUCTIONS

About the temperature controls.

Not a# features are on all models. Your controls may be similar to the following."

Temperature

[] Actumlremp Set Temp []

il ii_i

_i ii _ iii

i i ii_i iii_i _

Door

Reset

_od3 Se

Recommended 0° F Recommended 37° F

The temperature controls are preset in the factory at 37°Yfor the refrigerator compartment and O_Yforthe freezer compartment. Allow 24 hours for the temperature to stabilizeto the preset recommended settings.

The temperature controls can display both the SETtemperature as well as the actual temperature in the

refrigerator and freezer. Theactual temperature may vary slightly from the SETtemperature based on usage and operating environment.

Onsome models,setting both controls to the warmest setting until the display flashes(off)will stop cooling in both the freezer and refrigerator compartments.

On other models, setting either control to the warmest setting until the display flashes (off)will stop the cooling to the freezer and refrigerator.

NOTE'Turning the refrigerator off viathe controls on the touch panel does not shut off electrical power to the refrigerator.

NOTE."Therefrigerator isshipped with protective film- covering the temperature controls. If this film was not removed during installation, remove it now.

Performance Air Flow System

The Performance Air-Flow System is designed to

maximize temperature control in the refrigerator and

freezer compartments. This unique special feature

consists of theAir Tower along the back wall of the refrigerator and the Air Tunnel on the bottom portion

of the freezer rear wall.

Placing food infront of the louvers on these components will not affect performance. Although

the Air Tower and the AirTunnel can beremoved, doing sowill affect temperature performance. (For

removal instructions, on-line, 24 hours a day,contact usat GEAppliances.corn or call 800.GE.CARES. In Canada, contact us at geappliances.ca or call

1.800.561.3344.)

About ClimateKeeper2. TM (onsomemodds) CEA liancescom

, How it Works

The ClimateKeeper2 T_is the industry's most

advanced refrigeration system, delivering optimum temperature and humidity

performance to keep food garden fresh longer and reduce freezer burn,

The ClimateKeeper2 TM system features two

evuporutors--one for the refrigerotor ond one

for the freezer, This provides two separate cooling systems,

and separates the airflow between the fresh

food and freezer compartments during normal

cooling operations,*

This ensures that the humidity levels in the fresh food compartment are significantly higher

than in a conventional system,** allowing fresh

produce and other unsealed foods to retain

their moisture content and freshness longer,

Moisture sensitive foods such as fresh fruit, salads, rice, etc,, can now be stored on open

shelves without excessive moisture loss,

Due to the higher humidity in the refrigerator,

you may on occasion experience fog or

small amounts of moisture in the refrigerator compartment, This is normal and may

come and go as different food loads and environmental conditions change, Wipe dry

with a paper towel if desired, The separate airflow system minimizes the

mixing of air between the two compartments, which reduces fresh food odor transfer to

improve the taste of ice, The ClimateKeeperZ _ system also reduces

the number of defrosting cycles in the freezer evaporator, thereby reducing freezer burn,

_Freezerair is used in the CustomCooF feature, __Testing shows a higher level of humiditj/ in

the Fresh Food section in ClimateKeeperZ _

refrigerators versus conventional units,

About TurboCool. rM(onsomemodds)

How it Works

TurboCool TMrapidlycools the refrigerator

Turbo'

compartment inorder to more quickly cool foods, Use TurboCool TMwhenadding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers, Itcan also be used if the refrigerator has been without power for an extended period,

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours,The compressor will continue to run until the refrigerator

compartment coolsto approximately 34°F(1°C), then it will cycle on and off to maintain this setting,

After 8 hours, or if TurboCool TMispressedagain, the refrigerator compartment will return to the original setting,

How to Use

PressTurboCool TMTheTurboCool TMtemperature

display will show Tcand the LEDwillbe activated, After TurboCool _Miscomplete, the TurboCool _M

indicator light will go out, NOTES:Therefrigerator temperature cannot be

changed during TurboCool TM Thefreezer temperature is not affected

during TurboCool TM When opening the refrigerator door during

TurboCool TMthe fans will continue to run

ifthey have cycled on,

About ExpressChill TM _Ol? SOFRC f770dc/s_

How it Works

ExpressChill TM

The ExpressChilFMfeature is a system of dampers, a fan and a temperature thermistor,

The pan istightly sealed to prevent the pan's

The controls for this pan are located in the top of the refrigerator or on the dispenser with the

temperature controls,

temperature from causing temperature fluctuations in the rest of the refrigerator,

How to Use

0 Empty the pan, Place the Chill tray in the

pan, Place the items on the tray and close

the pan completely,

0 Select the ExpressChillTMpad, On some

models, you can then select the chill time

(use chart to determine best setting), Other

models will only have one option (45 minutes), On models with multiple settings,

tap the pad until the light appears next to

How to Remove and Replace the Drawer

To remove: 0 Lock all four swing locks by rotating them

Pullthe drawer out to the stop position, to the lock position, Rotate all four swing locks to the unlock

position, Lift the front of the drawer up and out,

To replace:

Make sure all four swing locks are in the unlock position,

Place the sides of the drawer into the drawer supports, making sure the swing

locks fit on the drawer slots,

the desired setting,

, To stop a feature before it is finished, tap

that feature's pad until no options are selected and the display is off,

, During ExpressChilFMthe display on the

controls will count down the time in the cycle,

015 MIN

ExpressChill _ii!i_!i!ii_e3oa=.

i • 45MIN

ExpressChilF M Chart (on some models)

NOTE: Results may vary depending on packaging, starting temperature and other food traits,

15 Minutes 30 Minutes 45 Minutes

1 Beverage Can (12 oz) 2 to 6 Beverage Cans 2 Liters of Beverage 2 Small ,Juice Boxes (12 oz each) 1/2 Gallon of,Juice

(6-8 oz each) 2 Plastic 20 oz Bottles Gel(]tin-! p(]ck(]ge

of Beverage 4 to 6 Small Juice Boxes (6-8 oz each)

3 Foil Juice Packets

Wine (750 ml bottle)

About the water filter. (onsomemodels) CEAppZi_nces.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment,

caitridge__

When to Replace the Filter on Models With a

Replacement Indicator Light

There is a replacement indicator light for the water filter cartridge on the dispenser, This light will turn orange to tell you

that you need to replace the filter soon, The filter cartridge should be replaced when the replacement

indicator light turns red or if the flow of water to the dispenser or icemaker decreases,

O Run water from the dispenser 1-1/2 gallons (about three

minutes) to clear the system and prevent sputtering,

_1 Press and hold the WATERF# TERpad (on some models) on

the dispenser for 3 seconds,

Fator

When to Replace the Filter on Models Without a

Replacement Indicator Light

The filter cartridge should be replaced every six months or earlier if the flow of water to the water dispenser or icemaker

decreases,

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly turning it to the left, Do not pull down on the cartridge, A

small amount of water may drip down,

Installing the Filter Cartridge

0 Ifyou are replacing a SmartWater cartridge with an

adapter, it must be removed before installing the cartridge,

To remove the adapter, turn it to the left about 1/4 turn,

Ifyou are replacing a Water by Culligan cartridge, leave the

adapter in place, This adapter will stay in the refrigerator when you replace future cartridges,

...................................................................

With adapter

(appearance may vary)

On models ithout a replacement indicator light, apply the

month and year sticker to the new cartridge to remind you

to replace the filter in six months.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after

installation,

Line up the arrow on the cartridge and the cartridge holder, Place the top of the new cartridge up inside the holder, Do

notpush it up into the holder, Slowly turn it to the right until the filter cartridge stops, DO

NOT OVERTIGHTEN As you turn the cartridge, it will

automatically raise itself into position, The cartridge will move about 1/2 turn,

Without adapter water filter,

use this type of

NOTE..A newly-installed water filter cartridge may cause water

to spurt from the dispenser upon first use,

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available, The dispenser and the icemaker will

not operate without the filter or filter bypass plug,

smartwater,

To use the filter bypass plug on Water by Culligan models, you must first remove the filter adapter from the cartridge holder by turning it to the left,

For the maximum benefit of your filtration system, GE recommends the use of GE branded SmartWater filters only, Using GEbranded filters in GEand Hotpoint refrigerators provides optimal performance and reliability, GE branded SmartWater filters are always the right choice because they are patented and designed specifically for GE products, GE SmartWater filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water, GEhas not qualified non-GE branded filters for use in GE and Hotpoint refrigerators and there is no

assurance that non-GE branded filters meet GE's standards for quality, performance and reliability,

If you hove questions-visit our Website ot GEAppliances.com, or call 1,800,GE,CARES(1,800,432,2737),

Replacement fitters:

Toorder additional filter cartridges in the United St_tes, visit our Website at GEAppliances.com, or car GE P_rts and Accessories

800.525.2002.

See filter label for type of filter to order (MWF or MSWF), Customers in Canada should consult the yellow pages for the

nearest Mabe Service Center,

Reset

Hold 3 Sec

iill

Bypass Ill

Water bY Cu!!igan

About the shelves and bins.

Not aN features are on aNmodels,

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable,

Toremove: Lift the front of the bin straight up,

then lift up and out,

Refrigerator bin

Toreplace or relocate: Engage the back side of

the bin in the molded supports of the door, Then

push down on the front of the bin, Bin will lock in place,

Small Bins

Toremove: Lift the front of the bin straight up

then out,

Thesnugger helps prevent tipping, spilling or

sliding of small items stored on the door shelf,

Place a finger on either side of the snugger near

the Fear and move it back and forth to fit your needs,

Top freezer bin

NOTE:

Be careful when

pMcing items in

the top bin, M_?ke sure that items do

not block or f_?ll into the ice chute,

Freezer bin

i i '

i ,

Freezer tilt-out bin

Press tab and pull shelf

forward to remove

Toreplace: Position the bin above the

rectangular molded supports on the door, Then slide the bin down onto the support to lock it in

place,

Slide-Out Spillproof Sheff

The slide-out spillproof shelf allows you to reach items stored behind others, The special edges are designed to help prevent spills from

dripping to lower shelves,

Toreplace or relocate:

Line the shelf up with the supports and slide it into place, The shelf can be repositioned when

the door is at 90° or more, To reposition the shelf, slide the shelf past the stops and angle

downward, Slide shelf down to the desired

)

Toremove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the shelf

straight out,

position, line up with the supports and slide into place,

Make sure you push the shelves all the way back in before you close the door,

Freezer Baskets (on some models)

To remove, slide out to the stop position, lift the Make sure you push the baskets all the way

front past the stop position, and slide out, back in before you close the door,

Freezer Baskets (on some models)

To remove, push the basket all the way to the

back of the freezer, Lift up until the back pins are disengaged, Lift the entire basket up and

pull out,

Make sure you push the baskets all the way back in before you close the door,

About the shelves and bins. CEApp/i ,nc s,com

Not all features are on a// models.

QuickSpace TMShelf(on some models)

This shelf splits in half and slides under itself for

) storage of tall items on the shelf below,

) This shelf can be removed and replaced or

J_J relocated just like Slide-Out Spillproof Shelves,

Slide-Out Freezer Shelves

Toremove, slide out to the stop position, lift the

front past the stop position, and slide out from

rib.

) Fixed Freezer Shelves

To remove, lift the shelf up at the left side and

then bring the shelf out,

Door Wine/Beverage Rack

(on some models)

This rack holds up to 5 cans, one bottle of wine or one 2-liter bottle of soda.

The rack hangs from the sides of the dairy bin.

Toremove:

Empty the wine/beverage rack.

On some models, this shelf can not be used in the lowest position.

Make sure you push the shelves all the way back in before you close the door.

NOTE FOR DISPENSER MODELS: In order to take full advantage of the tilt-out ice bin (on

some models), only store items on the shelf below the ice bin that are no taller than the

lowest point on the bin.

Holding the bottom of the dairy bin, lift the front straight up, then lift up and out.

To detach the rack from the dairy bin, pull the rack's side wires out of the holes on

each side of the dairy bin.

ShelfSaver TM Rack

(on some rnodds)

Use this rack to store beverage cans for easy

access,

It can also hold a 9" x 13" baking dish.

Removable Beverage Rack(on some models)

The beverage rack is designed to hold a bottle on its side. It can be

attached to any slide-out shelf.

Toreplace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the molded supports on the door. Then push

down on the front of the bin. The bin will lock into place.

Door Can Rack (onsome rnodds)

This door rack holds up to 9 cans.

NOTE."Thisrock can only be mounted in the top position under

the dairy bin,

To install:

Line up the large part of the slots on the top of the rack with

the tabs under the shelf. Then slide the rack back to lock

it in place.

About the refrigerator doors.

Refrigerator Doors (onsome models)

When the door is only partially open, it will automatically close,

Beyond this stop the door will stay open,

The refrigerator doors may feel different than the ones you are used to, The special

door opening/closing feature makes sure the doors close all the way and are securely

sealed, When opening and closing the door you will

notice a stop position, If the door is opened past this stop point, the door will remain

open to allow you to load and unload food more easily, When the door is only partially

open, it will automatically close,

Door A lignmen t

If doors are uneven, adjust the refrigerator door,

0 Using a 7/16" socket wrench, turn the

door adjusting screw to the right to raise the door; to the left, to lower it, (A nylon

plug, imbedded in the threads of the pin, prevents the pin from turning unless a

wrench is used,)

The resistance you feel at the stop position will be reduced as the door is loaded with

food,

0 After one or two turns of the wrench,

open and close the refrigerator door and check the alignment at the top of

the doors,

About the crispers and pans.

Not all features are on a// models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

OEApplL?nces,corn

HI LO

Slide the control all the way to the H/setting to provide high humidity recommended for most

vegetables.

Convertible Deli Pan (on some models)

Adjustable Humidity Crispers

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or refrigerator

compartment to flow to the pan.

The variable temperature contro/ regulates the

air flow from the Climate Keeper.

About crisper removal.

Not all features are on a// models.

CrisperRemoval

drawer straight out and lifting the drawer up and over the stop location.

Crispers can easily be removed by pulling the

Slide the control all the way to the LOsetting to provide lower humidity levels recommended for

most fruits.

Set the control to the coldest setting to store fresh meats,

Set the control to coldto convert the panto normal refrigerator temperature and provide

extra vegetable storage space. The cold air duct is turned off. Variable settings between

these extremes can be selected.

If the door prevents you from taking out the drawers, first try to remove the door bins.

If this does not offer enough clearance, the refrigerator will need to be rolled forward

until the door opens enough to slide the drawers out. In some cases, when you roll the

refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

A utomatic Icemaker

The icemaker will produce seven cubes per cycle- approximately 100-130 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the OFFposition.

When the refrigerator has been connected to the water supply, set the power switch to the O/Vposition.

The icemaker will fill with water when it cools to 15°F (-10°Q. A newly installed refrigerator may take 12 to 24 hours to begin

making ice cubes. You will hear a buzzing sound each time the icemaker fills with

water. Throw away the first few batches of ice to allow the water line

to clear. Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined

together. If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrink.

Avoid contact with the moving parts of

the ejector mechanism, or with the heating element (located on the bottom of the ice maker) that releases the cubes.

Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in.

Special note about dispenser models:

, Some models have a tilt-out ice bin. The bin can be tilted

out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on

and off. Be sure to put the bin back in place before closing the door.

, To restore your ice level from an empty bucket stage, the

following steps are recommended:

O 12 hours aflter the first batch of ice has fallen into the bin,

dispense 3 to 4 cubes.

O After an additional 6 hours, dispense 3 to 4 cubes again. These steps will restore your ice level in the shortest amount of

time.

IcemaKer Switch Icemaker

P Green Switch Feeler A-n Power Lign[ Feeler Arm

{on some models)

Power

(on some modds)

NO TE:

In homes with lower than average water pressure,

you may hear the icemaker cycle multiple times

when making one batch of ice.

About the automatic icemaker. (cont) CEA /i ,nc scom

Accessing Ice and Reaching the Power Switch on Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not, Special note for models with tilt-out ice bin:

, These models have a tilt-out ice bin, The bin can be tilted

out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch

on and off, Be sure to put the bin back in place before closing the door,

NO TE: /n order to take full adw}ntage of the tilt-out ice bin, only store items on the shell-below the ire bin that are no taller than the lowest point on the

bin.

Models with a sheff above the ice bin

ill _ iii i

iii

To reach the power switch, pull the

i i

shelf straight out. Always be sure to

To access ice, puff the bin fbrward.

replace the shelf

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

O Lift the then it fbrward

bin, pull

until the bin stops.

O ower the bin to access ice or

reach the power switch.

Removing Ice Bin (dispenser rnodds)

_ The ice bin is heavy when full,

Set the power switch to the OFF position before removing the bin,

When replacing the bin, be sure to press it firmly into place, If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn, Then push the bin back again,

On some models, to access

O u// the bin fbrward until the

bin stops.

Drive

ice or reach the power switch:

O ower the bin to access ice or

reach the power switch.

"iii_

Dispenser Models only

About the ice and water dispenser. ¢onsomemode/s)

To Use the Dispenser

Spill Shelf

Select CUBED/CE_ CRUSHED/CE or WATEl?_,

Press the glass gently against the top of the dispenser cradle,

The spill shelf is not self-draining, To reduce water spotting, the shelf and its grille should be

cleaned regularly, If no water is dispensed when the

refrigerator is first installed, there may be air in the water line system, Press the dispenser

arm for at least two minutes to remove trapped air from the water line and to fill the

water system, To flush out impurities in the water line, throw away the first six glassfuls

of water, CAUTION, Never put fingers or any other

objects into the ice crusher discharge opening,

Locking the Dispenser

3 seconds to lock the

L__ Press the LOCKpad for

dispenser and control panel, To unlock, press and

hold the pad again for 3 seconds,

Dispenser Light

This pad turns the/ightin the

dispenser on and off, The light also comes on when the

dispenser cradle is pressed, For models with a bulb, if

the light burns out, it should

be replaced with a 6 watt 12V maximum bulb, For LED

models, contact Factory Service,

[]

Quick Ice (on some models)

When you need ice in a

hurry, press this pad to speed up ice production, This will

increase ice production for

the following 48 hours or until you press the pad again,

DooyAlarm (on some models)

To set the alarm, press this

pad until the indicator light comes on, This alarm will

sound if either door is open

for more than 3 minutes, The light goes out and the

beeping stops when you close the door,

Important Facts About Your Dispenser

, Do not add ice from trays or bags to the

storage drawer, It may not crush or dispense well,

, Avoid overfilling glass with ice and use of

narrow glasses, Backed-up ice can jam the chute or cause the door in the chute to

freeze shut, If ice is blocking the chute, poke it through with a wooden spoon,

, Beverages and foods should not be quick-

chilled inthe ice storage drawer, Cans, bottles or food packages in the storage

drawer may cause the icemaker or auger to

jam,

, To keep dispensed ice from missing the

glass, put the glass close to, but not touching, the dispenser opening,

, Some crushed ice may be dispensed

even though you selected CUBED iCE,This happens occasionally when a few cubes

accidentally get directed to the crusher, After crushed ice is dispensed, some water

may drip from the chute,

, Sometimes a small mound of snow will form

on the door in the ice chute, This condition is normal and usually occurs when you have

dispensed crushed ice repeatedly, The snow will eventually evaporate,

Care and cleaning of the refrigerator. CEAppliancescom

Cleaning the Outside

The stainless steel doors and door handles

(on some models) can be cleaned with a commercially available stainless steel cleaner, Cleaners with oxalic acid such as Bar Keepers

Friend Soft Cleanser TM will remove rust, tarnish and small blemishes, Use only a liquid

cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge,

Do not use appliance wax or polish on the stainless steel,

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or

mild liquid dish detergent, Dry and polish with a clean, soft cloth,

Do not wipe the refrigerator with a soiled dish cloth or wet towel, These may leave a residue

that can erode the paint, Do not use scouring

pads, powdered cleaners, bleach or cleaners cont_?ining bleach because these products can scratch and weaken the paint finish,

Dispenser drip mea.

The dispenser drip area, beneath the grille,

should be wiped dry, Water left in this area may leave deposits, Remove the deposits by adding undiluted vinegar to the well, Soak until the

deposits disappear or become loose enough to rinse away,

The dispenser cradle, Before cleaning, lock the

dispenser by pressing and holding the LOCK pad for 3 seconds, Clean with warm water and

baking soda solution-about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water,

Rinse thoroughly and wipe dry,

The door handles and trim. Clean with a cloth

dampened with soapy water, Dry with a soft cloth,

Cleaning the Inside

Tohelp prevent odors, leave an open box

of baking soda in the fresh food and freezer compartments,

Unplug the refrigerator before cleaning. If

this is not practical, wring excess moisture

out of sponge or cloth when cleaning around switches, lights or controls,

Use warm water and baking sod(] solution- about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water, This both cleans and neutralizes odors, Rinse and wipe dry,

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or damage the interior of the refrigerator,

Do not clean glass shelves or covers with warm water when they are cold, Glass shelves and covers may break if exposed to sudden temperature changes or impact such as bumping or dropping, Tempered glass is designed to shatter into many small pieces if it breaks,

Do not wash any plastic refrigerator parts in the dishwasher,

The chill/thaw tray is dishwasher safb,

Care and cleaning of the refrigerator. (cont.)

Behind the Refrigerator

Be careful when moving the refrigerator away

from the wall, All types of floor coverings can

be damaged, particularly cushioned coverings and those with embossed surfaces,

Pull the refrigerator straight out and return it

to position by pushing it straight in, Moving the

refrigerator in a side direction may result in damage to the floor covering or refrigerator,

Preparing for Vacation

When pushing the refrigerator back, make sure you don't roll over the power cord or icemaker supply line (on some models),

For long vacations or absences, remove food and unplug the refrigerator, Clean the interior

with a baking soda solution of one tablespoon

(15 ml) of baking soda to one quart (1 liter) of

water, Leave the doors open,

Set the icemaker power switch to the OFF position and shut off the water supply to the

refrigerator,

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to

prevent damage,

When using a hand truck to move the

refrigerator, do not rest the front or back of the refrigerator against the hand truck, This could

damage the refrigerator, Handle only from the sides of the refrigerator,

Replacing the light bulbs. (onsomemodds)

Ifthe temperature can drop below freezing, have a qualified servicer drain the water supply

system (on some models) to prevent serious

property damage due to flooding,

Be sure the refrigerator stays in an upright position during moving,

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament, (A burned-out light bulb may break when being replaced,) Turning the control to the OFF position does not remove power to the light circuit,

Your light shield will look like one of the following:

Tabs

Refrigerator Compartment--Upper Light

Unplug the refrigerator,

The bulbs are located at the top of the

compartment, inside the light shield, On some models, a screw at the front of the

light shield will have to be removed, On other models, the screw is located in the

pocket located at the back of the shield, To remove the light shield, on some models,

press in on the tabs on the sides of the shield and slide forward and out, On other

models, just slide the shield forward and out,

O After replacing the bulb with an appliance

bulb of the same or lower wattage, replace the light shield and screw, When replacing

the light shield, make sure that the tabs at the back of the shield fit into the slots at the

back of the light shield housing,

Plug the refrigerator back in,

Replacing the light bulbs, contJ CEA /i ,nc s,com

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament, (A burned-out light bulb may break when being replaced,) Turning the control to the OFF position does not remove power to the light circuit,

Refrigerator Compartment--Lower Light

This light is located above the top drawer.

0 Unplug the refrigerator. 0 Lift the light shield up and pull it out.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace

the shield,

Plug the refrigerator back in,

Freezer Compartment

Unplug the refrigerator,

Remove the shelf just above the light shield, (Theshelf will be easier to remove if it is

emptied first,) Remove the screw at the top of the light shield,

0 To remove the light shield, press in on the

sides, and lift up and out.

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser under the control panel. Remove the light bulb by turning it counterclockwise.

Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling

the light shield, make sure the top tabs snap securely into place. Replace the

screw,

Reinstall the shelf and plug the refrigerator back in.

Replace the bulb with a bulb of the same size and wattage.

Plug the refrigerator back in.

Replacing the lights on models with LED lighting

Setting the controls to OFF does not remove power to the light circuit. Not all features are on all models.

Refrigerator Compartment (on some models)

There is an LED lighting display in the top and sides of the fresh food compartment and in the rear and side of the freezer compartment on some models.

II I 0_11 Lighting

/ .............. __] Display

If this assembly needs to be replaced, call GE Service at 1.800.432.2737 in the United States or

1.800.561.3344 in Canada.

Installation

efrigerator

Instructions

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEApp/iances.corn

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

" IMPORTANT - Save these instructions for

local inspector's use.

• IMPORTANT - Observeallgoverning

codes and ordinances.

• Note to Installer- Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for

future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

30 minutes

Water Line Installation

30 minutes

Models 22, 23, 25, 26, 27 & 29

PREPARATION

WATER SUPPLYTO THE ICEMAKER

If the refrigerator has an icemaker, it will have to be connected to a cold water line. AGE water supply

kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your

dealer, by visiting our Website at GEAppliances. corn (in Canada at www.geappliances.ca) or from

Parts and Accessories, 800.626.2002 (in Canada

1.800.661.1 616).

TOOLS YOU WILL NEED

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving the Refrigerator), then skip to Step 5 in/nsmlling the Refrigerator.

3/8" and 5/1 6" Socket 1/2" and 7/16" Wrench

PlasticPutty Knife

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

[]] LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the

refrigerator is in its final location. To move the refrigerator, use a padded hand

truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

If the refrigerator must go through any

entrance that is less than 38" wide, the doors must be removed. Proceed to

Step 3.

DO NOT remove the handles. If all entrances are more than 38" wide,

skip to/nstalling the Refrigerator.

D DISCONNECT THE WATER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the

bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

1-71REMOVETHE BASEGRILLE

Remove the grille by removing the two Phillips head screws.

Bottom

freezer

hinge

Installation Instructions

MOVING THE REFRIGERATOR(CONT.)

ra DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that

must be disconnected. To disconnect, pull apart at the coupling.

Bottom

freezer

hing_

v1 DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

D CLOSE THE FREEZER AND

REFRIGERATOR DOORS

E] REMOVE THE FREEZER DOOR

[_ Remove the freezer door top hinge cover (if

equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

r_ Remove the two 5/16" hex head screws, then

lift the hinge straight up to free the hinge pin.

5/16" Hex Head

Bottom refrigerator

hinge

:Tr_mi

r_ Open the freezer door to 90.°

90°

Installation Instructions

F1 REMOVE THE FREEZER DOOR (cont.)

r_ As one person slowly lifts the freezer door up

and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

r_ Set the door on a non-scratching surface with

the inside up.

[] REMOVE THE REFRIGERATOR DOOR

r_ Remove the refrigerator door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

D REMOVE THE REFRIGERATOR DOOR

(cont,)

_] Remove the two 5/16" hex head screws, then

lift the hinge straight up to free the hinge pin.

5/16" Hex Head

r_ Open the refrigerator door to 90.°

.... [

j -- • .......... >

90°

Installation Instructions

MOVING THE REFRIGERATOR(CONT.)

[]

REMOVE THE REFRIGERATOR DOOR

(cont,)

[]

Lift the refrigerator door up and off the bottom hinge.

If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

D REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following.

• When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure

you insert the tubing all the way to the mark.

90°

Refreshment Center Models only

r_ Set the door on a non-scratching surface with

the inside up.

Mark

• Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.

• When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

• Do not install the refrigerator in a location exposed

to water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing

and electrical connections:

23'/25' 23' (33" wide),

CustomStyle 'M 25', 26', 27', 29'

Sides Top

Back

1/8" (4 mm) 1/8" (4 mm)

1" (25 mm) 1" (25 mm)

1/2" (13 mm) -1" (25 mm)

DIMENSIONS AND SPECIFICATIONS (for

23' CustomStyld Mmodels)

o o

70¼" (178.4 cm)

)

(91.4cm)

24" (61cm)

DIMENSIONS AND SPECIFICATIONS (for

25' CustomStyld Mmodels)

DIMENSIONSAND SPECIFICATIONS

Water Electrical

_(19 mm)

Airspace

24" (61 cm) (1/2" [13 mm] Gap 3.5 cm)

+ 1/4" [6 mm] Wall Countertop

o ©

72¼" (183.5 cm)

)

36"_

91.4cm

24" (61cm)

"721/4" (183.5 cm) required for full adjustment

of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the

top of the opening for the refrigerator, then

an additional 1/8" may be required to provide clearance for cabinet doors to open freely.

Installation Instructions

INSTALLING THE REFRIGERATOR(CENT,)

CONNECTING THE REFRIGERATOR TO

[]

THE HOUSE WATER LINE (icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See "Installing the Water Line"

section.

NO TES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

• If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator's water

valve. Install it in the water line near the refrigerator.

If using GESmartConnect 'MRefrigerator Tubing Kit, you will need an additional tube

(WXO8X10002) to connect the filter. Do not cut plastic tube to install filter.

If you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect 'Mtubing, the nuts are already assembled to the tubing.

If you are using copper tubing, insert the end of

the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect 'Mtubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause

leaks.

D Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open the clamp.

Tubing Clamp

1/4"

Compression Nut

Ferrule

(sleeve)

Refrigerator Connection

[B TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

DI PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the OFF position.

SmartConnect 'MTubing

Option 2

See the grounding information attached to the power cord.

Installation Instructions

FZ]PUT THE REFRIGERATORIN PLACE

Move the refrigerator to its final location.

E] LEVELTHE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

___ - _- .....................

Rollers _

Rollers have three purposes:

• Rollers adjust so the door closes easily when

opened about halfway. (Raise the front about 5/8" [16 mm] from the floor.)

• Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

• Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23' (33" wide), 25', 26', 27' and 29' models:

Turn the roller adjusting screws

clockwise to raise the refrigerator,

counterclockwise

to lower it. Use a 3/8" hex socket

or wrench, or an adjustable wrench.

Raise

[_ LEVEL THE REFRIGERATOR (cont.)

To adjust the

rollers on 23'/25' CustomStyle 'Mmodels:

Turn the front roller adjusting screws

clockwise to raise the refrigerator,

counterclockwise to lower it. Use a 3/8" hex

wrench with extension, or an adjustable wrench. These models also have rear adjustable

rollers so you can align the refrigerator with

your kitchen cabinets. Use a 3/8" hex wrench

with extension to turn the screws for the rear rollers--clockwise to raise the refrigerator,

counterclockwise to lower it.

Roller adjusting screws

LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

To align:

Using a 7/16" wrench, turn the door adjusting

screw to the right to raise the door, to the left to lower it.

NO TE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a

wrench is used. After one or two turns of the wrench, open

and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Roller adjusting screw

Installation Instructions

INSTALLING

THE REFRIGERATOR(CONT.)

171REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips

head screws.

[_ START THE ICEMAKER

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to fill the ice

bin.

Power switch

E] SET THE CONTROLS

Set the controls to the recommended setting.

I"EOOMME"OEOOO"'"O'SE"°OS]

lift

0 _FIS RECOMMENDED 37 °F IS RECOMMENDED

Power switch

NOTE: In lower water pressure conditions, the water

valve may turn on up to 3 times to deliver enough water to the icemaker.

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER&DISPENSERMODELS)

BEFOREYOU BEGIN

Recommended copper water supply kits are WXSX2, WXSX3 or WXSX4, depending on the amount of tubing you need. Approved plastic water supply lines are GE

SmartConnect 'MRefrigerator Tubing (WXOSX10006, WXOSX10015 and WXOSX10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

iswith a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer's recommendations.

If the water supply to the refrigerator is from

a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter,

use the refrigerator's filter bypass plug. Using the refrigerator's water filtration cartridge in

conjunction with the RO filter can result in hollow

ice cubes and slower water flow from the water

dispenser.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of

expensive water damage.

WHAT YOU WILL NEED

• Copper or GESmartConnect _MRefrigerator Tubing kit, 1/4" outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the

refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to

move out from the wall after installation. GE SmartConnect 'MRefrigerator Tubing Kits are

available in the following lengths:

8' (2.8 m) - WXOSX10006 15' (4.6 m) - WXOSX10015 25' (7.6 m) - WXOSX10025

Water hammer (water banging in the pipes)in

house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is

in the OFF position.

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

Installation Instructions

INSTALLING THE WATER LINE

WHAT YOU WILL NEED (CONT,)

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect _MRefrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at ail times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

• A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available

at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada

1.800.661.1616).

• A cold water supply, The water pressure must be

between 20 and 120 p.s.i.(1.4-8.1 bar).

• Power drill.

• 1/2" or adjustable wrench.

• Straight and Phillips blade screwdriver.

(CONT,)

Install the shutoff valve on the nearest frequently used drinking water line.

ITI SHUT OFF THE MAIN WATER SUPPLY

_herriion ot_enta_est fa ucet long enough to clear

1"71CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily accessible. It is best to connect into the side of

a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

• Two 1/4" outer diameter compression nuts and 2 ferrules (sleeves)--to connect the copper tubing to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect 'MRefrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

• If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water

line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting, Do not cut formed end from GE SmartConnect 'MRefrigerator tubing.

• Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32" at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply

kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

IIIm_

E] DRILL THE HOLE FOR THE VALVE

Drill a 1/4" hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the

pipe. Take care not to allow water to drain into the

drill.

Failure to drill a 1/4" hole may result in reduced

ice production or smaller cubes.

Installation Instructions

I]-I FASTENTHE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

Pipe Clamp

Saddle-Type Shutoff Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to.

Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

E] TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

Washer

Pipe Clamp X,_

Clamp Screw

Vertical Cold Water Pipe

Inlet End

E] CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and

connect it to the shutoff valve. Make sure the tubing is fully inserted into the

valve. Tighten the compression nut securely. For plastic tubing from a GE SmartConnect 'M

Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Saddle-Type

Shutoff V_

Packing Nut

Outlet Valve

NOTE: Commonweal,-h of Massachusetts Plumbing Codes 248CMR shall be adhered to.

Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

r_ FLUSH OUT THE TUBING

Compression Nut

_, _ / SrnartC°nnectTM Tubing

Ferrule (sleeve)

r_ ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing to

allow the refrigerator to move out from the wall after installation.

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed through the tubing.

To complete the installation of the refrigerator, go back to Step 1 in/nsmlling the Refrigerator.

Normal operating sounds.

Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.

Do you hear what I hear? These sounds are normal

--HUMMM... WHOOSH

[]

The new high efficiency compressor may run faster and longer than your old refrigerator and you may

hear a high-pitched hum or pulsating sound while it is operating,

[] Sometimes the refrigerator runs for an extended period,

especially when the doors are opened frequently, This means that the Frost Gu_rd_Mfeature is working to

prevent freezer burn and improve food preservation,

[] You may hear a whooshing sound when the doors close,

This is due to pressure equalizing within the refrigerator,

[] You may hear

the fans spinning at high speeds, This happens when the refrigerator is first plugged in, when the doors are

opened frequently or when a large amount of food is added to the refrigerator or freezer compartments, The fans are helping to maintain the correct temperatures,

[]

If either door is open for over 3 minutes, you may hear

the fans come on in order to cool the light bulbs,

[]

The fans change speeds in order to provide optimal cooling and energy savings,

CLICKS,POPS,

CRACKSand CHIRPS

[] You may hear cracking or popping sounds when the

refrigerator is first plugged in, This happens as the refrigerator cools to the correct temperature,

[] Electronic dampers click open and closed to provide

optimal cooling and energy savings,

[] The compressor may cause a clicking or chirping sound

when attempting to restart (this could take up to 5 minutes),

[] The electronic control board may cause a clicking

sound when relays activate to control refrigerator components,

[] Expansion and contraction of cooling coils during and

after defrost can cause a cracking or popping sound,

[] On models with an icemaker, after an icemaking cycle,

you may hear the ice cubes dropping into the ice bucket,

WATERSOUNDS

[] The flow of

refrigerant through the freezer cooling coils may make a gurgling noise like boiling water,

[] Water dropping on the defrost heater can cause a

sizzling, popping or buzzing sound during the defrost cycle,

[] A water dripping noise may occur during the defrost

cycle as ice melts from the evaporator and flows into the drain pan,

[] Closing the door may cause a gurgling sound due to

pressure equalization,

+ 98 hidden pages