GE GUD27EESNWW Specification Sheet
GUD27EESN GUD27GESN
GE® Unitized Spacemaker® 3.9 DOE Cu. Ft. Stainless Steel Washer and 5.9 Cu. Ft. Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRICAL REQUIREMENTS:
GUD27EESN Electric Dryer – This appliance should be connected to an
individual, properly-grounded branch circuit with 120/240V or 120/208V
single-phase 60 Hz electrical service and should be protected by
30-amp time-delay fuses or circuit breakers KW Rating per voltage
(240/208). This appliance is manufactured with neutral connected to
the frame. Power cord should be purchased separately.
GAS REQUIREMENTS:
GUD27GESN Gas Dryer – This appliance should be connected to an
individual branch circuit with 120-volt single-phase 60 Hz electrical
service and should be protected by 20-amp time-day fuses or circuit
breakers. This appliance is equipped with a 4-foot long flexible U.S.
listed 20-amp power cord to match a 20-amp receptacle.
NOTE: Gas Rated input 20,000 BTU/HR. Factory equipped for natural
gas. Tested for LP gas. LP gas supply requires a conversion kit. Have a
qualified gas technician install a conversion kit before use.
Dryers must be exhausted to the outside.
INS TA LLATI ON IN F ORMATI ON: For complete information, see
installation instructions packed with the product.
75-7/8"
Installation Instructions
27" NOMINAL PRODUCT DIMENSIONS
18-5/8"
Water Inlets
Vent
53-1/4"
Drain outlet
(rear)
3-7/8"
22-1/4"
* Dimension represents door closed including handle and knobs.
26-3/4"
NOTE: With feet set at mid position, feet can be adjusted +/- 3/8".
13-1/4"
36-7/8"
(rear)
51°
*26-1/8"
47 1/2"
30-7/8"
Gas Inlet
(Rear view of appliance)
3"
3"
34-3/8"4-3/8"
For answers to your GE Profile™ Series or GE Appliances product questions, visit our
website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Listed by
Underwriters
Laboratories
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Speci fication Revised 4/19
GUD27EESN GUD27GESN
GE® Unitized Spacemaker® 3.9 DOE Cu. Ft. Stainless Steel Washer and 5.9 Cu. Ft. Dryer
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
For complete information, see installation instructions packed with your dryer.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting
can be used (Kit WX08X10077). In special installations, it may be necessary to connect the
dryer to the house vent using a f lexible metal (foil-type) duct. A UL-listed flexible metal
(foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semirigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the
entire length of the transition duct. Please see installation instruction packed with your
dryer for complete instructions when using f lexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side
or bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft. Two 45° elbows
will be treated like one 90° elbow. For the side exhaust installations, add one 90° elbow to
the chart. The total vent system length includes all the straight portions and elbows of the
system (transition duct included)..
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any
enclosed house f loor (crawl space), or into an attic, since the accumulated lint could create
a fire hazard or moisture could cause damage. Never terminate the exhaust into a common
duct or plenum with a kitchen exhaust, since the combination of lint and grease could create
a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
No. of 90º
Elbows
0
1
2
3
GUD27 DRYER EXHAUST LENGTH
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Recommended
4" DIA. 4" DIA.
4"
Rigid
Metal
56 Feet
48 Feet
40 Feet
32 Feet
Use only for short
run installations
4" DIA.
Rigid
Metal
42 Feet
34 Feet
26 Feet
18 Feet
2-1/2"
For answers to your GE Profile™ Series or GE Appliances product questions, visit our
website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
Listed by
Underwriters
Laboratories
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Speci fication Revised 4/19
Loading...