GE GTW685BSLWS Installation Manual
SAFETY INSTRUCTIONS ..........4
USING THE WASHER
Getting Started ...................... 6
Loading .............................16
CARE AND CLEANING ............17
INSTALLATION
INSTRUCTIONS .................... 19
TROUBLESHOOTING TIPS ..... 24
CONSUMER SUPPORT
Warranty ........................... 27
Consumer Support ................... 28
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
GTW750
GTW685
GTW680
ENGLISH/ESPAÑOL
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
WASHERS
GE is a trademark of the General Electric Company. Manufactured under trademark license.
You can find them under the
lid of the washer.
49-90577 05-17 GEA
G014
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
2 49-90577
Notes
WELCOME
49-90577 3
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
SAFETY INFORMATION
WARNING
Ŷ
Read all instructions before using the appliance.
Ŷ
DO NOT wash or dry articles that have been previously cleaned in, washed in, soaked in or spotted with
gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could
ignite or explode.
Ŷ
DO NOT add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or explode.
Ŷ
Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for
2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a
period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for
several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, DO NOT smoke
or use an open flame during this time.
Ŷ
DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this
appliance is used near children. Before the washer is removed from service or discarded, remove the door or
lid. Failure to follow these instructions may result in death or injury to persons.
Ŷ
DO NOT reach into the appliance if the tub or agitator is moving to prevent accidental entanglement.
Ŷ
For waterproof, water-resistant and bulky items, only use the Bulky Items (or Delicates) cycle. DO NOT use
other cycles for these items. Using other cycles can cause excessive vibration and may result in injury or
damage to the washer, walls, or floor. DO NOT mix waterproof and non-waterproof items.
Ŷ
DO NOT install or store this appliance where it will be exposed to the weather.
To reduce the risk of death, fire, explosion, electric shock, or injury to persons when using
your appliance, follow basic precautions, including the following:
Ŷ
DO NOT tamper with controls, repair or replace any part of this appliance or attempt any servicing unless
specifically recommended in the user maintenance instructions or in published user repair instructions that you
understand and have the skills to carry out.
Ŷ
DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or
broken parts including a damaged cord or plug.
Ŷ
Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power button DOES NOT
disconnect power.
Ŷ
See “ELECTRICAL REQUIREMENTS” located in the Installation Instructions for grounding instructions.
PARTS AND ACCESSORIES
Order on-line at GEApplianceparts.com today,
24 hours a day or by phone at 800.626.2002 during
normal business hours. In Canada, visit your local
GE Appliances parts distributor or call 800.661.1616.
Part Number Accessory
PM14X10002 4 ft rubber water supply hoses
Or
PM14X10005 4 ft braided water supply hoses
WH49X301 Drain hose extension
PM7X1 Washer Floor Tray
READ AND SAVE THESE INSTRUCTIONS
4 49-90577
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
PROPER INSTALLATION
This washer must be properly installed and located in accordance with the Installation Instructions before it is used.
Ŷ
Ensure that the hot water hose is connected to the “H” valve and the cold water hose is connected to the “C”
valve.
Ŷ
Install or store where it will not be exposed to temperatures below freezing or exposed to the weather, which
could cause permanent damage and invalidate the warranty.
Ŷ
Properly ground washer to conform with all governing codes and ordinances. Follow details in the Installation
Instructions.
SAFETY INFORMATION
WARNING
Plug into a grounded 3 prong outlet.
DO NOT remove ground prong.
DO NOT use an adapter.
DO NOT use an extension cord.
Failure to follow these instructions can result in death, fire or electrical shock.
Ŷ
Ensure washer is properly leveled and washer legs are adjusted such that unit is stable.
Ŷ
Optional drain hose extension recommended for discharging heights from 60” - 96”.
Ŷ
GE Appliances strongly recommends the use of factory specified parts. A list of factory hoses available for
purchase are listed. These hoses are manufactured and tested to meet GE Appliances specifications.
Ŷ
GE Appliances strongly recommends the use of new water supply hoses. Hoses degrade over time and need
to be replaced every 5 years to reduce the risk of hose failures and water damage.
- Electrical Shock Hazard
START-UP SEQUENCE
Ŷ
Any time the washer is being started or restarts after the washer lid has been opened and closed, the washer
will turn on the cold water valve for two short periods followed by a 10 second pause before continuing. If the
lid is opened during this period, the washer will pause. You will have to push the Start button again to restart
the cycle.
AUTOMATIC DRAIN SEQUENCE
Ŷ
Machine will automatically drain any time the lid is left open for more than 15 minutes and water is present.
Ŷ
Machine will automatically drain if left in a paused state with the lid closed for more than 24 hours and water is
present.
Ŷ
Machine will automatically drain after dispensing water in Water Station mode after the cycle knob has been
turned to another cycle.
WHEN NOT IN USE
Ŷ
Turn off water faucets to minimize leakage if a break or rupture should occur. Check the condition of the fill
hoses; GE Appliances recommends changing the hoses every 5 years.
READ AND SAVE THESE INSTRUCTIONS
49-90577 5
Getting started
WARNING
Throughout this manual, features and appearance may vary from your model.
Step 1
IMPORTANT: See the
specific dispenser
section in this
manual for
your model.
• Add fabric softener to the fabric
softener dispenser.
USING THE WASHER
• Add the manufacturer ’s
recommended amount of detergent.
GE Appliances recommends the
use of High Efficiency
such as in your energy
efficient washer. Place detergent
pods in the bottom of the wash
basket before adding clothes.
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
Step 2
• Loosely add items around
Infusor or agitat or. Overloading
may negatively impact wash
performance. See page 16 for
suggested loading examples.
detergents
• Close lid.
NOTE: Unless using Bulky Items
cycle washer will not start with
lid open.
A
D
C
Step 3
• Select wash cycle.
• Select wash options,
including Deep Rinse
option when using
fabric softener.
• Select options.
Step 4
•
Press
Start.
B
A
B
E
D
F
G
G
C
Lid Lock
Spin Stop
J
H
H
I
HI
I
H
H
I
HI
Power
A
Press to “wake up” the display. If the display is active, press to put the washer into idle mode.
NOTE: Pressing Power does not disconnect the appliance from the power supply.
6 49-90577
Getting started
Start/Pause
B
Press Start to begin the cycle. NOTE: Unless Bulky Items cycle is selected, the lid must be closed for the washer to start cycle.
If the lid is open, “Lid” will scroll across the display. During the load sensing portion of the cycle, the lid will lock and “SEnSing” will
scroll across the display. When load sensing is complete, the lid will unlock.
Pressing Pause will unlock the lid (if locked at that time), pause the cycle and the Start indicator light will blink.
To continue the cycle, press Start again. If water remains in the machine, select the Drain & Spin cycle to drain basket and
spin water out of the washer basket. NOTE: Machine will automatically cancel and drain when water is present and the lid is
left open for 15 minutes or the unit is left in a paused state for 24 hours with the lid closed. Select cycle and press Start to
begin new cycle.
Display and Status Lights
C
Display: The display shows the approximate time remaining until the end of the cycle. NOTE: The cycle time is affected by
how long it takes the washer to fill. This depends on the water pressure in your home. The size of the load being washed also
significantly impacts cycle time, with larger loads taking longer.
In addition, this display will, “scroll” the washer status:
• bALAnCINg Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• dELAY When Delay Wash is initiated. Replaced with estimated time when cycle starts.
• End End of current cycle.
• FILL “FILL” will scroll across display for the first 45 seconds of fill, afterwards the estimated end of cycle time is
displayed.
• H2O SUPPLY Can not sense water level (valves possibly turned off).
• LId Cycle stopped because lid is open. Close the lid.
• SEnSIng Sensing load size and type before and during fill (normal).
• PAUSE Cycle paused because the Start/Pause button was pressed and the washer was set to Pause. Press Start
button again to restart the cycle.
Cycle status lights: Shows whether the washer is in the Delay, Fill, Soak (on some models), Wash, Rinse or Spin
portion of the cycle.
If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle
and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct th e
out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able to balance the load
and spin up to f ull speed. If you notice the load is more wet than normal at the end of the cycle, redistribute the load evenly
in the wash basket and run a Drain & Spin cycle.
Feature status lights indicate (see sections F and G for more details):
Pause - Will display when washer is paused between cycles.
Controls - The washer is locked - will blink once if you press any button or turn the cycle knob.
Lid Lock - The lid is locked. See the Control Lock description.
WiFi (on some models) - Will display when washer is connected via WiFi. Will blink when you are attempting to connect
your device to your home WiFi.
Spin Stop - Indicates wash basket is coasting to a stop following spin. Lid will not unlock until basket has fully come to a stop.
USING THE WASHER
Consumer Help Indicator
Your washer is equipped with Consumer Help Indicator (CHI). CHI is our way to communicate a simple remedy for some situations
that you can perform without the need to call for service. The chart below describes the helpful messages you may notice scrolling
on your display when you return to start another load. These messages will provide simple remedies you can quickly perform.
Spin light blinking If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion
“H2O SUPPLY”
(Water not
entering washer)
“CAnCELEd” “CAnCELEd” may scroll on the display if the machine was paused for longer than 24 hours or if the machine
“Lid” “Lid” will be shown on display if 3 cycles have been started without opening the lid. The washer will not
49-90577 7
of the cycle and will stay illuminated for a short time after cycle completion. When this occurs, the washer
is taking actions to correct the out-of-balance condition and complete the cycle normally. In some cases,
the washer may not be able to balance the load and spin up to full speed. If you notice the load is more wet than
normal at the end of the cycle, redistribute the load evenly in the wash basket and run a Drain & Spin cycle.
Check your house water supply. Did you forget to turn on one or both supply valves after installation or
coming back from vacation? As soon as the message starts to scroll, the washer will initiate a 4 minute lockout period. The washer controls won’t respond/change during this time. After the 4 minutes, you can begin
your cycle again. If you try to bypass the lock-out period by unplugging the washer, the 4 minute timer will
start over again.
has stopped itself before the cycle completed due to certain errors. As soon as the message starts to scroll,
the washer will initiate a 4 minute lock-out period. The washer controls won’t respond/change during this time.
After the 4 minute period, you can begin your cycle again. If you try to bypass the lock-out period by unplugging
the washer, the 4 minute timer will start over again. If the problem persists, call GE Appliances at 800.
GE.CARES (800.432.2737) for service.
start another cycle until the lid is opened. Try opening, then closing the lid and starting a new cycle. If the
problem persists, call GE Appliances at 800.GE.CARES (800.432.2737) for service.
Getting started
Wash Cycles-Cycle Selector Knob
D
The wash cycle controls the type of washing process. The cycle selector knob can be turned in either direction. Turning the
knob after starting a cycle will stop the washer and change the cycle/options to the new selection. Press Start to begin the
new cycle selection.
The chart below will help you match the items to be washed with the best wash cycle settings. For optimal performance,
select the cycle that most closely matches the items being washed.
Selections and options shown in bold are the recommended settings for that cycle.
Some cycles and options may not be available on some models.
Items to Wash Cycle Wash Temp Soil Level Spin
Cycle for normal,
regular, or typical
use for washing
up to a full load
of normally soiled
USING THE WASHER
cotton clothing.
Casual clothes,
lightly soiled
office wear.
Lingerie and
special care
fabrics with light
soil. Waterresistant, bedding
and bulky items,
such as large
coats, mattress
pads, and bath
mats.
Medium to lightly
soiled athletic
wear items of
technical or
synthetic fabrics.
Dark colored
fabrics and mixed
loads.
Small loads of
lightly soiled
items that are
needed in a hurry.
Examples include
one casual wear
outfit or 3 soccer
uniforms.
Wet load of items.
For items that
need only to be
rinsed, use this
cycle with Deep
Rinse option.
Colors Hot
Casuals Hot
Delicates Hot
Active
Wear
Cold
Wash
Speed
Wash
Drain &
Spin
Warm
Colors
Cool
Cold
Tap Cold
Warm
Colors
Cool
Cold
Tap Cold
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Selection
(Duration)
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Options Available Cycle Details
Stain Removal Guide
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Deep Rinse
Extra Rinse
Cycle for normal, regular, or typical
use for washing up to a full load
of normally soiled cotton clothing.
Choose the Heavy or Extra Heavy soil
level selection and Warm or Hot water
temperature selection as appropriate
for your clothes load for a higher
degree of cleaning. Incorporates multistage fills and wash periods to provide
optimal fabric care.
Wash cycle tailored to care for
casual clothes and office wear
items.
Utilizes a unique “tri-pulse” extra
gentle agitate profile and a low spin
speed to provide special care to
delicate fabrics. It is recommended
to place small or ultra delicate items
in mesh bags before washing.
Cycle designed for care of medium
to lightly soiled active wear,
athletic wear, and technical fabrics.
Incorporates a dual stage wash
period with soak to effectively treat
body soils and odors. Use the Heavy
Duty cycle for heavily soiled sports
clothing constructed of sturdy fabric.
Cycle combines multiple wash
agitation periods with soak periods
to provide enhanced cleaning
performance and energy efficiency
with colder water temperatures.
Utilizes more intense agitation
profile, expedited wash period, and
time saving continuous spray rinse
to clean small lightly soiled loads in
the fastest time possible.
Utilizes a high speed spin to extract
water from wet items. For items that
need to be rinsed, select the Deep
Rinse option when using this cycle.
8 49-90577
Getting started
USING THE WASHER
Items to Wash Cycle Wash Temp Soil Level Spin
Cleaning the
basket of residue
and odor. No
clothes to be
washed using this
cycle.
Heavily soiled
colorfast items.
Jeans with
medium to light
soil. For heavily
soiled work jeans,
use the Heavy
Duty Cycle.
Sturdy fabrics with
heavy to medium
soil.
Water-resistant,
bedding and
bulky items, such
as large coats,
mattress pads,
and bath mats.
Towels
Sheets
Whites and
household linens
Basket
Clean
Sanitize
with Oxi*
Jeans Hot
Heavy
Duty
Bulky
Items
Towels /
Sheets
Whites Hot
Hot Ex. Heavy Normal Deep Fill
Hot Ex. Heavy Max
Ex. Heavy
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Hot
Warm
Colors
Cool
Cold
Tap Cold
Warm
Colors
Cool
Cold
Tap Cold
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Ex. Heavy
Heavy
Normal
Light
Selection
(Duration)
More
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Max
More
Normal
No Spin
Options Available Cycle Details
Deep Rinse
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Stain Removal Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse
Recommended use of at least
once per month. Never load
laundry when using this cycle;
laundry may become damaged or
contamina ted. Cycle incorporates
a hot deep wash, intense agitation
action, a dispenser purge (on
some models), and a deep rinse.
Cycle uses an initial lower water
fill for super concentrated, high
temperature sanitization followed by
a heavy wash step. A pump purge
and deep rinse is incorporated to
remove contaminants. See additional
details and certifications below. Smart
Dispense not available on this cycle.
Combines higher water levels,
a specially designed agitation
profile, and multi-step wash and
soak periods to care for jeans
with medium to light soil. Use
the Heavy Duty cycle for heavily
soiled work jeans.
Incorporates multi-step wash
and
soak periods combined
with extended
to effectively clean heavily to
medium soiled sturdy fabrics.
Provides a Deep Fill/max fill wash
water level to wash bulky and
waterproof items. Also incorporates
a Deep Fill rinse to effectively rinse
bulky items and a low spin speed
appropriate for these items. Only
use this cycle for water-resistant,
bedding or bulky items.
Cycle designed washing towels or
sheets, using a higher water level
and a soak period to effectively clean
these items. It is recommended
that towels and sheets be washed
separately for best care and washing
performance. For waterproof bed
covers use Bulky Items cycle.
Cycle tailored to clean and brighten
your whites.
wash periods
CAUTION
Failure to follow these instructions may result in injury or property damage.
For Waterproof, Water-Resistant, or Bulky Items:
•
Only use the Bulky Items (or Delicates) cycle. NOTE: Some models only have a Delicates cycle
Using other cycles can cause excessive vibration and may result in injury or damage to the washer, walls, or
•
.
floor.
Do not mix waterproof and non-waterproof items
•
Read the Owner’s Manual for wash cycle details.
•
49-90577 9
.
Getting started
*Sanitize with Oxi
The Sanitize With Oxi cycle, when using an Oxi additive along with your detergent, is designed to remove 99.9% of bacteria found in
home laundry. Measure the detergent and the Oxi products carefully. Using the amounts appropriate for a large heavily soiled load
in a top load washer, follow the detergent and the Oxi product label instructions. For the Sanitize With Oxi cycle only, add the clothes
first and then place the detergent and Oxi product directly on top of the load. The washer hot water supply connection must provide
a minimum of 120°F to ensure the effectiveness of this cycle.
NOTE: The default Sanitize With Oxi cycle water temperature can NOT be changed.
The Sanitize With Oxi cycle is certified by NSF International, an independent third party testing and certification organization. The
certification verified that the cycle reduced 99.9% of bacteria typically found in residential laundry and that no significant contamination
is transferred to subsequent washer loads. Only the Sanitize With Oxi cycle has been designed to meet the requirements of NSF
Protocol P172 for sanitizing effectiveness.
NSF Protocol P172
Sanitization Performance of Residential and
Commercial, Family-Sized Clothes Washers
USING THE WASHER
Pretreating or Soaking Using Water Station (on some models)
E
This feature is for pretreating of garments
only and not intended to serve as an
actual wash cycle. When selected, the
washer will supply either fresh water or
water mixed with detergent from your
SmartDispense system for garment hand
pre-washing or pre-treating use.
The pretreating water will be dispensed
from the area located in the back of
the main opening of the washer. When
selected, any water dispensed into the
wash tub during the pretreat will be drained
from the machine before any subsequently
selected wash cycle can begin.
Water Station only
Select this feature:
1. Rotate the cycle selection knob to Water Station.
2. Push the Select button until the LED below Water is
3. Select the desired water temperature using the Temp
4. Press the Start button to initiate the feature.
If the lid is not already open, raise the lid of the washer to
start the flow of fresh water from the dispensing area. Water
will continue to be dispensed until the lid is closed or the
water level in the tub reaches the maximum level.
illuminated.
button.
Alternatively, you can use this feature
to soak your garments in the pretreated
water for up to 24 hours with the lid closed
and the cycle knob remaining on Water
Station.
In order to use this feature to soak, keep
dial on Water Station and close the lid.
You can soak for up to 24 hours before
the water in the tub will be automatically
drained. Rotating the dial, holding the
Start button for 3 seconds or leaving the
lid open for more than 15 minutes will all
automatically drain the water from the tub.
If the lid is closed before the maximum level in the tub is
reached, additional water can be dispensed by opening
the lid again. Once the lid is closed, water dispensed using
the water on demand feature will remain in the tub until the
cycle selection knob is rotated to an actual wash cycle, or
the Start button is held in for 3 seconds, at which point the
water in the tub will be drained out of the machine.
If the lid is not closed, the water in the tub will automatically
be drained after 15 minutes. With the lid closed, if the cycle
selection knob is not rotated to an actual wash cycle, or the
Start button is not held in for 3 seconds, the water in the
tub will automatically be drained after 24 hours.
Water Station with Detergent
Select this feature:
1. Rotating the cycle selection knob to the Water Station.
2. Push the Select button until the LED below Detergent +
Water is illuminated.
3. Select the desired water temperature using the Temp
button.
4. Press the Start button to initiate the detergent feature.
If the lid is not already open, raise the lid of the washer
to start the flow of soapy water from the dispensing area.
Soapy water will continue to be dispensed until the lid is
closed or the water level in the tub reaches the maximum
level.
If the lid is closed before the maximum level in the tub
is reached, additional soapy water can be dispensed by
simply opening the lid again. Once the lid is closed, soapy
water dispensed will remain in the tub until the cycle
selection knob is rotated to an actual wash cycle, or the
Start button is held in for 3 seconds, at which point the
soapy water in the tub will be drained out of the machine.
If the lid is not closed, the soapy water in the tub will
automatically be drained after 15 minutes. With the lid
closed, if the cycle selection knob is not rotated to an actual
wash cycle, or the Start button is not held in for 3 seconds,
the soapy water in the tub will automatically be drained
after 24 hours.
10 49-90577
Getting started
Stain Removal Guide (on some models)
F
The Stain Removal Guide feature allows you to indicate what stains are on the garments in your load. This feature
incorporates a patent pending treatment method. An initial water fill is performed at a temperature tailored to the stain type
selected and to an amount which enables a concentrated cleaning step. A stain scrubbing period, followed by an active
soak, is conducted to effectively treat the stain. Then additional water is added to the selected temperature and the wash
phase is conducted for the cycle selected.
This feature can be applied to most wash cycles as described in the cycle guide.
To use Stain Removal Guide:
1. Select the desired wash cycle.
2. Press the Stain Removal Guide button.
Continue to press to select Tomato stain, Wine stain, Blood stain, Grass stain or Dirt stain. The indicator light will show
the selected stain.
To select a different stain, press the Stain Removal Guide button until desired stain to be removed is lit.
To turn off Stain Removal Guide, press until no indicator lights are illuminated.
NOTE: The Soil and Temperature levels will be changed to match the recommended default setting for each stain type.
Turning off Stain Removal Guide will return the settings to default.
Stain Removal Guide
Category
Blood Cold/Cool Blood
Grass Cold/Warm Grass
Dirt Cool/Warm Dirt
Tomato Cool/Warm Sauce
Wine Cool/Warm Wine
• Recommended temperatures are optimal for stain removal performance; adjust temperature selection to suit load being
washed.
• Ensure stain is completely removed after wash cycle and before placing in dryer; very tough stains may require a second
treatment.
Recommended
Temperatures
Treatment/Wash
Stain
Sweat
Body Fluids
Urine
Lipstick
Chocolate
Gravy
Mayonnaise
BBQ Sauce
Clay
Mud
Catsup
Salsa
Soda
Kool-Aid
Tea
Coffee
Juice
Beer
For best results,
before placing in washer:
Rinse in cold water; pretreat
stain with liquid detergent or
stain remover product.
Pretreat with liquid
detergent or stain remover
product. Brush lightly; rinse
with cold water.
Allow dirt to dry; remove
loose dirt using a brush.
Rinse with cool water.
Pretreat with liquid
detergent or stain remover
product; rinse with cool
water.
Pretreat with mixture of Oxi
product and cool water.
Add Oxi product along with
detergent in the washer.
USING THE WASHER
49-90577 11
Getting started
Settings
G
Individual settings for agitation (Soil), water temperature (Temp), and spin (Spin) can be set from the minimum (lowest in
column) to maximum (highest in column). In general, the higher up the column, the more washer energy will be used.
NOTE: Longer Spin times typically reduce dryer time/energy usage (i.e. reduces total energy when using both a washer and
a dryer).
Cycle Options
H
Deep Fill
Select the Deep Fill feature for loads where extra water is needed. The Deep Fill feature is recommended for special case
loads only, not for typical use.
Press the Deep Fill button once before starting the cycle to add an incremental amount of water to the wash load. Holding the
Deep Fill button for 3 seconds will provide the deepest fill level possible; this will increase cycle time due to the additional time it
takes to fill the washer.
To cancel the option if desired, press the Deep Fill button again.
NOTE: The Deep Fill button can also be pressed after the washer has completed filling and is in the wash phase if additional
USING THE WASHER
water is desired. To stop the extra fill, press the Deep Fill button again and the water will stop.
Warm Rinse
Provides a warm rinse to your wash load. Note that rinsing operations may be different with this operation selected in order to
effectively apply the warm rinse water to your load.
Auto Soak
This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the cycle
automatically. Repeated pressing of the Soak button will scroll through 15 minute, 30 minute, 1 hour and 2 hour selections and
then return back to 0 soak minutes.
Deep Rinse
Set this option to provide a deep rinse or when using fabric softener. It may change other settings (e.g. Spin may go to a higher
setting) to maximize performance.
Delay Wash
When the Delay Wash button is repeatedly pressed, the delay time is set from 1 (01H) to 9 (09H) hours and back to clear (00H)
hours. If you
Extra Rinse
When you use extra detergent or bleach to clean heavily soiled clothes, use the Extra Rinse option to better remove additional
residues. NOTE: This option is not allowed for some cycles.
press and hold the Delay Wash button for 3 seconds, it will immediately reset.
Additional Options
I
My Cycle Settings
As the cycle selector knob is turned, the Temp, Soil and Spin settings change to automatic pre-set default settings for each
cycle. If you desire different default settings, select the desired options or changes to the cycle settings, then press and hold
the My Cycle button for 3 seconds to s tor e th em . The My Cycle button will light when active. In the future, when you
turn the selector knob to that cycle, your settings will be automatically recalled. To restore the factory defaults temporarily
(i.e. for this load), press the My Cycle button for 1/2 second. The My Cycle light will turn off and the factory defaults will
load. However, the next time you select this cycle, your My Cycle settings will load. If you wish to permanently restore the
factory default settings for the cycle; when the My Cycle is active (button light on) press and hold the My Cycle button for 3
seconds. The factory defaults will load for the selected cycle and the My Cycle light will turn off. The default settings will load
when this cycle is selected in the future and the My Cycle light will remain off. NOTE: My Cycle saves the following options:
Temp, Soil, Spin, Extra Rinse, Deep Fill, Warm Rinse, Auto Soak, Deep Rinse and Stain Removal Guide.
Volume (on some models)
Use the Volume button to change the volume of the end of cycle signal and other system tones. Press the button until you reach
the desired volume (high, medium, low) or off.
Control Lock
Use the control lock before or during a cycle to prevent any selections from being made.
To lock/unlock the washer controls, press and hold the Warm Rinse and Auto Soak buttons for 3 seconds. The control lock
icon will light up when it is on. NOTE: The Power button can still be used when the machine is locked.
12 49-90577
Getting started
Smart Dispense (GTW750 model only)
J
When selected, this feature will automatically add
detergent to the wash, eliminating the need to add
detergent for each load.
The detergent amount selection on the control panel
will default to AUTO when first powering up the washing
machine. When AUTO is selected, the amount of detergent
needed for each laundry load will automatically be
determined based on the size of the load the machine
senses.
USING THE WASHER
If it is desired to manually select the amount of
detergent for a given load, this can be done by pressing
the Detergent Dispense button on the control panel to
select detergent for a Small, Normal or Large load. Small
will provide less detergent than average, Normal will
provide an average amount of detergent and Large will
provide more detergent than average.
The smart dispense feature can be disabled by pressing
the Detergent Dispense button until Off is selected.
NOTE: Not all cycles will allow the use of the Smart
Dispense feature. If the light is illuminated below the Off
position and pressing the Detergent Dispense button
results in a beeping tone, then Smart Dispense is not
allowed for the cycle that has been selected. Detergent
will need to be added directly to the wash basket for these
cycles.
Bulk Smart Dispenser
(GTW750 model only)
This model does not have a dispenser drawer for detergent
since it has a bulk detergent dispensing system.
NOTE: If it is desired to manually add detergent for a
load, that detergent will need to be added directly to
the basket, and the smart dispense set to OFF for that
particular load.
NOTE: The right side of the dispensing area in the rear of
the washer opening does NOT pull out. It is a spout only
for water and detergent to flow from the smart dispense
system.
Adding Detergent to Bulk Smart Dispenser
(GTW750 model only)
This machine is equipped with a bulk detergent reservoir
that can hold approximately 75 ounces of liquid detergent
for your convenience. This is enough detergent for about
50 average laundry loads, depending on what dispense
amount is selected.
Bulk Dispensing
Spout Only
Do NOT pull
Pretreatment
Water On Demand
MAX
Conditioner
NOTE: If it is desired to change detergent type in the
detergent tank, it is not required to flush the smart dispense
system. The new detergent type can be added to a partiallyfilled tank, however it will not be immediately dispensed
until the original detergent is completely dispensed from the
system.
NOTE: In the event that excessive chlorine bleach is
accidentally spilled or otherwise gets into the detergent
tank, please follow the Detergent Tank Clean-Out
instructions in the Care and Cleaning section in order to
minimize the possibility for clothing damage. If only a few
drops of bleach are spilled into the detergent tank, there is
no need to flush the tank.
The filling port of the detergent reservoir is located on the
front left of the washing machine. To fill the reservoir with
liquid detergent, first open the tank lid by rotating the small
lid clockwise. Then pour LIQUID detergent into the opening
until the level reaches the MAX indicator located inside
the filling port, also indicated with the horizontal line next
to the MAX lettering. Filling to this MAX level will provide
detergent for about 50 average laundry loads. To ensure
detergent is always available, liquid detergent should
be added to the reservoir whenever there is no longer
detergent visible when looking directly into the filling port.
49-90577 13
Getting started
Liquid Fabric Softener/Conditioner Dispenser
Liquid fabric softener/conditioner should be added to the small
drawer in the rear of the washer opening. Follow the liquid
fabric softener/conditioner manufacturer’s recommendations
for the correct amount of softener/conditioner, based on the
load size. Do not overfill or dilute softener/conditioner as this
can result in additive being dispensed prematurely in the wash
cycle. Your option selections will determine when liquid fabric
softener/conditioner is automatically dispensed at its optimal
time in the rinse cycle.
NOTE: Fabric softener crystals should NOT be added to the
dispenser drawer, as they will not dispense properly.
Liquid Bleach
USING THE WASHER
Use a measuring cup to pour the bleach into the bleach
dispenser. Measure liquid bleach carefully and DO NOT pour
directly from the bleach bottle into the bleach dispenser.
NOTE: The bleach dispenser is a single use dispenser and is
NOT a bulk dispense system. The maximum amount of bleach
that should be poured into this dispenser for any load should
never exceed 1 cup.
NOTE: In the event that excessive chlorine bleach is
accidentally spilled or otherwise gets into the detergent tank,
please follow the Detergent Tank Clean-Out instructions in the
Care and Cleaning section in order to minimize the possibility
for clothing damage. If only a few drops of bleach are spilled
into the detergent tank, there is no need to flush the tank.
NOTE: In the event that detergent is accidentally spilled or
otherwise gets into the bleach opening, that detergent will
simply be used for the next wash cycle. In this case there is no
need to perform any flushing routine.
(GTW750 model only)
(GTW750 model only)
MAX
Conditioner
Pretreatment
Water On Demand
14 49-90577
Getting started
Detergent Dispenser
(GTW680 and GTW685 models only)
HE detergent should be added to the right side of the
dispenser drawer. Follow the detergent manufacturer’s
recommendations for the correct amount of detergent,
based on load size, taking care to add detergent to the right
compartment. Do not overfill or dilute detergent as this can
result in additive being dispensed prematurely in the wash
cycle. Your option selections will determine when detergent is
automatically dispensed at its optimal time in the wash cycle.
For optimal performance, especially when selecting cooler
temperature and in cold weather climates, place powdered HE
detergent directly in the wash basket before adding clothes.
NOTE: Single-dose laundry packets should not be added to
the dispenser drawer, as they will not dispense properly. Put
packets in bottom of wash basket.
Liquid Fabric Softener/Conditioner Dispenser
(GTW680 and GTW685 models only)
Liquid fabric softener/conditioner should be added to the left
side of the dispenser drawer. Follow the liquid fabric softener/
conditioner manufacturer’s recommendations for the correct
amount of softener/conditioner, based on load size, taking care
to add softener/conditioner to the left compartment. Do not
overfill or dilute softener/conditioner as this can result in additive
being dispensed prematurely in the wash cycle. Your option
selections will determine when liquid fabric softener/conditioner
is automatically dispensed at its optimal time in the rinse cycle.
NOTE: Fabric softener crystals should NOT be added to the
dispenser drawer, as they will not dispense properly.
USING THE WASHER
Liquid Bleach Dispenser
(GTW680 and GTW685 models only)
Liquid chlorine bleach should be added through the
bleach dispenser in the front left corner. Follow bleach
manufacturer’s recommendations for the correct amount of
liquid chlorine bleach based on load size, taking care to not
apply or spill it directly on clothing.
NOTE: Do not use liquid chlorine bleach and laundry
pretreatments such as an Oxi product in the same wash load.
49-90577 15
Loading
Always follow fabric manufacturer’s care label when laundering.
Automatic Load Sensing
This determines the correct agitate profile, agitate duration and amount of water suited to the size and type of load placed in the
washer. The washer will not start the wash cycle or fill with water if the lid is open. When the lid is closed the machine is able to
begin filling with water in order to sense the load size.
LOADING
NOTE: Automatic Load Sensing initiates a spin at the beginning of the cycle and will take as much as 3 minutes to complete
(significantly shorter for smaller loads); this is normal operation.
NOTE: This is a high efficiency washing machine. This system requires less water while providing effective cleaning action. You
may notice that the water level is lower than on your previous washer. This is normal for a high efficiency washer.
Pretreatment
Place laundry pretreatments, such as an Oxi product, directly in the bottom of the wash basket before loading clothes.
NOTE: Do not use liquid chlorine bleach and laundry pretreatments such as an Oxi product in the same wash load.
Proper Use of Detergent
Using too little or too much detergent is a common cause of
laundry problems.
Use less detergent if you have soft water, a smaller load or a lightly
soiled load.
For spots, apply pre-treatment to items as recommended on the
product label. Application should be made in the basket to prevent
overspray which may cause the coloring on the lid or graphics to
fade.
Place detergent pods in the bottom of the wash basket before
adding clothes.
GE Appliances recommends the use of High Efficiency det ergents
such as
formulated to work with low water wash and rinse systems. HE
detergents reduce the oversudsing problems commonly
associated with regular detergents.
When using high efficiency or concentrated detergents, consult
the product label to determine amount required for optimum
performance. Excessive detergent will negatively impact wash
performance.
in your energy efficient washer. HE detergents are
Sorting Wash Loads
Sort by color (whites, lights, colors), soil level, fabric type (sturdy cottons, easy care, delicates) and whether the fabric produces
lint (terry cloth, chenille) or collects lint (velveteen, corduroy). Wash lint producers such as cotton towels and socks separate from
lint collectors including synthetic garments and dress pants.
WARNING
- Fire Hazard
DO NOT wash fabrics soiled with flammable liquids or cleaning solvents.
No washer can completely remove oil.
DO NOT wash or dry anything that has been soaked in or spotted with any type of oil (including cooking oils).
DO NOT reach into the washer until all moving parts have stopped.
Doing so can result in death, explosion, fire or amputation.
Loading the Washer
Load dry items loosely in the washer basket. For best results, load items evenly and loosely around the outside of the basket, filling in
towards the center on larger loads. To add items after washer has started, press Start/Pause if the lid is locked; wait until the Lid Lock
indicator on the display is no longer illuminated before attempting to open the lid. Lift the lid and submerge additional items around the
outside of the basket. Close the lid and press Start to resume. Adjust load size selection and/or use Deep Fill option if necessary.
Ŷ
Do not place large items such as
sheets, blankets and towels across
the Infusor. Load them around the
outside of the basket.
Ŷ
Do not put lawn or sofa cushions
into the washer as they are too big
to move. Remove outer covers and
ONLY wash them.
Clothes Level
Water Level
Average Small Load
Clothes Level
Water Level
Average Medium Load
Average Large Load
Clothes Level
Water Level
16 49-90577
Care and Cleaning
Exterior of the Washer
Immediately wipe off any spills with a damp cloth.
Interior of the Washer
NOTE: For the GTW750 model, the following instructions
should be followed using the Bulky Items cycle.
To clean the interior of the washer, select the Basket Clean
feature on the control panel. This Basket Clean cycle should
be performed, at a minimum, once per month. This cycle will
use more water, in addition to bleach, to control the rate at
which soils and detergents may accumulate in your washer.
NOTE: Read the instructions below completely before starting
the Basket Clean cycle.
1. Remove any garments or objects from the washer and
ensure the washer basket is empty.
2. Open the washer lid and pour one cup or 250
ml of liquid bleach or other washing machine
cleaner into the basket.
3. Close the lid and select the Basket Clean cycle. Push the
Start button.
4. When the Basket Clean cycle is working, the display will
show the estimated cycle time remaining. Do not interrupt
the cycle.
Basket Clean may be interrupted by pressing the Start button
in between cycles. A power outage in the house might also
interrupt the cycle. When the power supply is back, the Basket
Clean cycle resumes where it had stopped. When interrupted,
be sure to run a complete Basket Clean cycle before using the
washer. If the Power button is pressed during Basket Clean,
the cycle will be lost.
IMPORTANT:
Ŷ
Run Basket Clean with 1 Cup (250 ml) of bleach once a
month.
Ŷ
After the completion of a Basket Clean cycle, the interior of
your washer may have a bleach smell.
CARE AND CLEANING
Dispenser Drawer
After some period of use, a small amount of detergent or
softener residue may be present in the dispenser drawer. The
drawer can easily be removed for cleaning. To remove the drawer,
pull it out until the drawer stops and then lift up on the front of the
drawer. The drawer can then be removed from the dispenser box.
Wash the drawer in warm, soapy water using a mild detergent.
Rinse drawer with warm water. If siphon caps are removed for
cleaning, be sure to push siphon caps fully back into place after
cleaning.
Detergent Tank Clean-Out
(GTW750 model only)
NOTE: All clothes should be removed from the washer prior to
cleaning out the detergent tank.
To empty out the tank and remove any remaining detergent
from the reservoir:
1. Press and hold both the Detergent Dispense and Select
buttons for three seconds.
2. The empty out routine will begin with the contents of tank,
mixed with water, being dispensed into the basket and
consequently drained from the machine at the same time.
3. The empty out routine will continue for approximately 15
minutes unless it is paused by the pressing of the Start
button. If tank is initially full, routine may need to be run a
second time to empty detergent tank.
The dispenser drawer and siphon caps are not dishwasher
safe. The dispenser box is not removable, but it can be wiped
clean using a damp cloth if necessary. Do not attempt to
remove the dispenser box for cleaning.
Pretreatment
Water On Demand
MAX
Conditioner
GTW750 model has a small
dispenser drawer with one
compartment for softener/
conditioner only.
NOTE: Optionally, hot water can be added to the tank to aid in
flushing out the system of any residual detergent prior to starting
or during the cleanout routine.
GTW680 and GTW685 models
have a large dispenser drawer
with compartments for both
detergent and softener.
49-90577 17
Loading...