<![if ! IE]> <![endif]>DRYERS |
|
|
|
SAFETY INFORMATION . . . . . . . . |
. .3 |
|
USING THE DRYER |
|
|
Getting Started . . . . . . . . . . . . . . . . . . . . . |
. 4 |
|
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
.8 |
|
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
.8 |
|
CARE AND CLEANING . . . . . . . . . . |
.9 |
|
INSTALLATION |
|
|
INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . |
.12 |
|
Stacking (Optional) . . . . . . . . . . . . . . . . . . . . . |
20 |
|
Reversing The Door Swing (Optional). . . . . |
22 |
|
TROUBLESHOOTING TIPS. . . . . |
24 |
|
LIMITED WARRANTY . . . . . . . . . . . |
27 |
|
CONSUMER SUPPORT . . . . . . . . . . |
28 |
|
Write the model and serial |
|
|
numbers here: |
|
|
Model #_________________ |
|
|
Serial # _________________ |
|
|
They are on the label on the front |
|
|
of the dryer behind the door. |
|
GE is a trademark of the General Electric Company. Manufactured under trademark license.
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
GFT14
ENGLISH/FRANÇAIS/
ESPAÑOL
0020507767Z 49-90571-3 10-19 GEA
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration card included in the packing material.
2 |
|
49-90571-3 |
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
|
To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance, |
|
WARNING |
||
follow basic precautions, including the following: |
ŶRead all instructions before using the appliance.
ŶDO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
ŶDO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
ŶDO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance is used near children.
ŶBefore the appliance is removed from service or discarded, remove the door to the drying compartment.
ŶDO NOT reach into the appliance if the drum is moving.
ŶDO NOT install or store this appliance where it will be exposed to the weather.
ŶDO NOT tamper with controls.
ŶDO NOT climb or stand on this unit.
ŶDO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
ŶFollow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.
ŶDO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
ŶDO NOT dry articles containing foam rubber or similarly textured rubber-like materials.
ŶClean lint screen and clean and empty the condenser before or after each load.
ŶDO NOT operate the dryer without the lint filter and condenser in place.
ŶDO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the air intake vent on the front of the dryer and adjacent surrounding areas free from the accumulation of lint, dust and dirt.
ŶThe interior of the appliance should be cleaned periodically by qualified service personnel.
ŶUnplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES NOT disconnect power.
ŶDO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
ŶDO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when cleaning dryer interior. Hazardous fumes or electrical shock could occur.
ŶSee “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.
<![endif]>INFORMATION SAFETY
READ AND SAVE THESE INSTRUCTIONS
49-90571-3 |
3 |
<![endif]>USING THE DRYER
Getting started
|
|
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY |
|
WARNING |
|
|
INFORMATION before operating this appliance. |
|
|
|
|
Throughout this manual, features and appearance may vary from your model.
Step 1 |
Step 2 |
Step 3 |
•Loosely add items.
•Close door.
NOTE: Dryer will not start with door open.
Power
•If the screen is dark, press the Power button to “wake up” the display.
•Select a dry cycle. (Defaults are set for each dry cycle. These default settings can be changed. See control settings for more information.)
|
OR |
Timed |
Temp |
Dry |
•Press Timed Dry button, rotate knob to adjust time, and press Temp button to set your own temperature.
Step 4
Start
Pause
•Press the Start/Pause button.
Controls |
|
|
|
|
|
|
|
|
|
|
|
L |
M |
|
N |
|
|
|
B |
|
K |
A |
|
DRY |
DAMP |
COOL |
|
|
|
|
|
Mixed Loads |
Quick Dry |
|
|
|
|
|
|
|
Cottons |
Delicates |
|
|
|||
High |
Ex Dry |
Clean Filter |
|
Est Time Remaining |
|
|
|||||
|
Heavy |
|
|
|
|||||||
Medium |
|
Empty Tank |
|
|
|
|
Dewrinkle |
|
|
||
|
|
|
|
|
Duty |
Start |
Power |
||||
|
|
|
|
|
|
||||||
Low |
Dry |
|
|
|
|
|
|
Towels |
Warm Up |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
Casuals |
|
Pause |
|
No Heat |
Damp |
Damp |
TimedDamp |
|
My Cycle |
Tumble |
Delay |
|
|
|
|
|
|
|
|
|
|
|
|
Active |
Rack Dry |
|
|
|
|
|
|
|
|
|
|
Wear |
|
|
|
Temp |
Level |
Damp |
Timed |
eDry |
My Cycle |
Ext |
Delay |
Sanitize |
|
|
|
Alert |
Dry |
Tumble |
Dry |
|
|
|
|
||||
|
|
|
|
|
Hold to Set |
|
|
|
|
|
|
C |
D |
E |
F |
G |
H |
I |
J |
|
|
|
|
4 |
49-90571-3 |
Getting started
A Power
Press to “wake up” the display. If the display is active, press to turn the dryer off.
NOTE: Pressing Power does not disconnect the appliance from the power supply.
B Dry Cycles
The dry cycle controls the cycle time for the drying process. The chart below will help you match the dry setting with the loads.
|
Mixed Loads |
For loads consisting of cottons and poly blends. |
|||
|
or Normal |
|
|
||
|
(Depending on |
|
|
||
|
model) |
|
|
||
|
Cottons |
For cottons and most linens. NOTE: Energy Star® models are tested on Cottons with |
|||
|
|
|
|
default settings. |
|
|
Heavy Duty |
For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets, |
|||
|
|
|
|
small rugs, and similar large and bulky items. |
|
|
Towels |
Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load. |
|||
|
Casuals |
For wrinkle-free, permanent press and delicate items, and knits. |
|||
|
Active Wear |
Clothing worn for active sports exercise and some casual wear. Fabrics include new technology |
|||
|
|
|
|
finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press: |
|
|
|
|
|
For wrinkle-free and permanent press items. |
|
|
Sanitize |
Reduces certain types of bacteria by 99.6%, including: Staphylococcus aureus and Pseudomonas |
|||
|
|
|
|
aeruginosa. The antibacterial process occurs when high heat is used during a portion of this |
|
|
|
|
|
drying cycle. |
|
|
|
|
|
|
|
|
Quick Dry |
For small loads that are needed in a hurry, such as sports or school uniforms. Can also be |
|||
|
|
|
|
used if the previous cycle left some items damp, such as collars or waistbands. |
|
|
Delicates |
For lingerie and special-care fabrics. |
|||
|
Dewrinkle |
For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended |
|||
|
|
|
|
for delicate fabrics. |
|
|
Warm Up |
Provides 25 minutes of warming time to warm up clothes. |
|||
|
Air Fluff |
Provides 30 minutes of tumbling time without heat. |
|||
|
Rack Dry |
For drying delicate items without tumbling, use drying rack accessory. Place items flat on the |
|||
|
|
|
|
drying rack such as wool sweaters and delicate fabrics. Dry with low heat. |
|
|
|
|
|
|
|
C |
|
Temp |
Temp (Temperature) |
||
|
|
You can change the temperature of your dry cycle. |
|||
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
High |
For regular to heavy cottons. |
|
|
|
|
Medium |
For synthetics, blends and items labeled Permanent Press. |
|
|
|
|
Low |
For delicates, synthetics and items labeled Tumble Dry Low. |
|
|
|
|
No Heat |
This option may only be used with Air Fluff and Timed Dry, in which items are |
|
|
|
|
|
tumbled without heat. |
<![endif]>DRYER THE USING
49-90571-3 |
5 |
<![endif]>USING THE DRYER
Getting started
D |
Level |
|
Level |
|
|
|
The sensor continuously monitors the amount of moisture in the load. When the moisture in |
||
|
|
|
your clothes reaches your selected dry level, the dryer will stop. |
|
|
|
|||
|
|
|
NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack |
|
|
|
|
Dry, Warm Up and Dewrinkle. |
|
|
|
|
|
|
|
|
|
Ex Dry |
Use for heavy-duty fabrics or items that should be very dry, such as towels. |
|
|
|
Dry |
Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving. |
|
|
|
Damp |
For leaving items partially damp. |
|
|
|
|
|
E |
Damp |
|
Damp Alert |
|
|
Alert |
|
This option causes the dryer to beep when clothes have dried to a damp level. Remove |
|
|
|
items that you wish to hang dry. The Damp Alert will only beep when this option is selected, |
and the dryer will continue to dry.
Removing clothes and hanging them when they are damp can reduce the need to iron some items.
F |
Timed |
|
Dry |
|
|
Timed Dry
1.Press Timed Dry button. Lights around the knob will flash. Select the drying time by rotating the knob to increase or decrease the time in 10-minute increments up to 2 hours and 30 minutes.
2.Select the dry Temp.
3.Close the door.
4.Press Start/Pause.
G |
eDry |
eDry (on some models) |
|
|
Reduces total energy consumption of specific dryer cycles by adjusting certain heat settings. |
|
|
NOTE: Cycle times will change when eDry is selected. |
|
|
|
|
|
Energy Star® models are tested on Cottons cycle with default settings to determine energy |
|
|
use rating of this dryer. The eDry option will default to on for Cottons. Temperature settings |
|
|
on High and dryness level setting on Dry are specifically designed for this cycle to reduce |
|
|
energy consumption. For optimal energy savings, turn eDry on. For optimal drying times, |
|
|
turn eDry off. Energy savings will vary across loads and cycles. |
|
|
The eDry selection can be used with Mixed Loads, Cottons, Heavy Duty, Towels, |
|
|
Casuals, Active Wear and Delicates. |
HMy Cycle
Hold to Set
My Cycle
Set up your favorite combination of settings and save them here for one touch recall. These custom settings can be set while a cycle is in progress.
To store a My Cycle combination of settings:
1.Select your drying cycle.
2.Change Temp and Level settings to fit your needs.
3.Select any drying options you want.
4.Press and hold the My Cycle button for 3 seconds to store your selection. A beep will sound and the button will light up.
To recall your stored My Cycle combination:
Press the MY CYCLE button before drying a load.
To change your stored My Cycle combination:
Repeat steps 1–4.
I |
Ext |
Extended Tumble |
|
Tumble |
Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are |
|
dry. |
|
|
|
The estimated time remaining display will show “END”. |
|
|
The extended tumble time does not get added to the cycle time on the display. |
6 |
49-90571-3 |
Getting started
J Delay
Dry
Delay Dry
Use to delay the start of your dryer.
1.Choose your dry cycle and any options.
2.Press Delay Dry. You can change the delay time in 1 hour increments, using the Delay Dry button.
3.Press the Start/Pause button to start the countdown.
NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not restart unless the door is closed and Start/Pause button has been pressed again.
K
Start
Pause
Start/Pause
Press to start a cycle. If the dryer is running, pressing it once will pause the dryer and unlock the door. This function can be used to add garments during a cycle. Press again to restart the cycle.
NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current cycle will be cancelled.
L |
Temp |
Level |
|
Lock |
|
|
|
|
|
|
You can lock the controls to prevent any selections from being made. Or you can lock or |
|
|
|
|
||
|
|
|
|
|
unlock the controls after you have started a cycle. |
|
|
|
|
|
Children cannot accidentally start the dryer by touching pads with this option selected. |
|
|
|
|
|
To lock the dryer, press and hold the Temp and Level buttons together for 3 seconds. |
|
|
|
|
|
To unlock the dryer controls, press and hold the Temp and Level buttons together for 3 |
|
|
|
|
|
seconds. A sound is made to indicate the lock/unlock status. |
|
|
|
|
|
The control lock icon on the display will light up when it is on. |
|
|
|
|
|
NOTE: The Power button can still be used when the machine is locked. |
|
|
|
|
|
|
M |
Damp |
Timed |
|
Signal |
|
|
Alert |
Dry |
|
When the light is on, the dryer will beep at the end of the cycle and every time you press a |
|
|
|
|
|
|
button on the control panel. |
|
|
|
|
|
|
|
|
|
|
|
To turn the signal off, press and hold the Damp Alert and Timed Dry buttons together for 3 |
|
|
|
|
|
seconds. A sound is made to indicate the lock/unlock status. |
N
DRY |
DAMP |
COOL |
|
High |
Ex Dry |
Clean Filter |
Est Time Remaining |
Medium |
|
Empty Tank |
|
Low |
Dry |
|
|
No Heat |
Damp |
Damp TimedDamp |
My Cycle Tumble Delay |
Display and Status Lights
The display shows the approximate time remaining until the end of the cycle.
In addition, this display will show the dryer status:
Status |
DRY |
DAMP |
COOL |
Controls locked on.
End of cycle signal on.
Clean Filter Time to clean the filter. See the Care and Cleaning section.
Empty Tank Time to empty the water tank. See the Care and Cleaning section.
Temp Shows High, Medium, Low or No Heat temperature setting selected.
Level Shows Extra Dry, Dry or Damp dryness setting selected.
Damp Alert Indicates Damp Alert is set and will sound when the clothes have dried to a damp dryness level.
Timed Indicates that a Timed Dry cycle is set. Will turn off after cycle is finished.
Est Time Display shows the estimated time remaining until set cycle is completed.
Remaining
My Cycle Indicates the My Cycle feature is set.
Ext Tumble Indicates the Extended Tumble feature is set.
Indicates Delay Dry is set time is selected.
<![endif]>DRYER THE USING
49-90571-3 |
7 |
<![endif]>USING THE DRYER
Loading
Always follow fabric manufacturer’s care label when laundering.
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
Dry Labels
|
|
Tumble |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
dry |
|
|
|
|
|
|
|
|
Do not dry |
|
|
|
|
Dry |
Normal |
Permanent Press/ |
|
Gentle/ |
|
|
|||||
|
|
|
Do not tumble dry (used with |
|
|||||||||
|
|
|
|
wrinkle resistant |
|
delicate |
|
do not wash) |
|
||||
|
|
Heat |
|
|
|
|
|
|
|
|
|
|
|
|
|
setting |
|
|
|
|
|
|
|
|
|
|
|
|
|
High |
Medium |
|
Low |
|
No heat/air |
|
|
|
|
||
|
|
Special |
|
|
|
|
|
|
|
|
|
|
|
|
|
instructions |
Line dry/ |
Drip dry |
Dry flat In the shade |
|
|
|
|||||
|
|
|
|
|
|
||||||||
|
|
|
hang to dry |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sorting and Loading Hints |
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
WARNING |
- Fire Hazard |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
• Keep flammable materials and vapors, such as |
• DO NOT dry anything that has ever had any type of oil |
|||||||||||
|
|
gasoline, away from dryer. |
|
|
|
|
|
|
|
on it (including cooking oils). |
|
||
|
• DO NOT dry anything that has ever had anything |
• |
Items containing foam, rubber, or plastic must be dried |
|
|||||||||
|
|
flammable on it (even after washing). |
|
|
|
|
|
on a clothesline. |
|
||||
|
• No washer can completely remove oil. |
|
|
|
• |
Failure to do so can result in death, explosion, or fire. |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the manufacturer’s instructions.
Do not overload. This wastes energy and causes wrinkling.
Drying Rack
A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.
To install the drying rack, extend the drying rack into the dryer drum and rest the front two legs on the front angled ledge.
NOTES:
ŶThe drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles may result in damp items or extended cycle times.
ŶDo not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.
ŶThe drying rack, WE01X26416, is available as an accessory. Order on-line at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.
8 |
49-90571-3 |
Care and cleaning
Interior
The interior of the appliance should be cleaned once a year by qualified service personnel.
Exterior
Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.
Lint Filter
Clean the lint filter before each use.
Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide the filter back into position. Have a qualified technician vacuum the lint from the dryer once a year.
NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.
Stainless Steel
To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces. Remove the cleaner residue and then dry with a clean cloth.
The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface blemishes will not affect the function or durability of the drum.
Drum Lamp
NOTE: The drum lamp is not consumer replaceable on models where there is a flat cover over an LED bulb. If this light should ever stop working, call for service.
For models that have a domed cover over the bulb secured by a screw:
Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum to locate the light.
Remove the screw and the plastic cover to access the bulb. Replace with the appropriate bulb and then reaffix the cover and screw.
Order replacement bulb WE11X26351 on-line at GEApplianceparts.com, by phone at 877.959.8688 during normal business hours, or purchase appliance bulb 7C7 from your local retailer.
When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed, the drum lamp will remain on for 30 seconds.
WARNING - Electrical Shock Hazard
Disconnect power supply before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING - Shock Hazard
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.
Service personnel – DO NOT contact the following parts while the appliance is energized: motor start capacitor, motor metal holder, and drum wheel shaft.
<![endif]>CLEANING AND CARE
49-90571-3 |
9 |
<![endif]>CARE AND CLEANING
Care and cleaning
Water Tank
REMOVE THE CONDENSED WATER IN THE TANK AFTER EVERY DRYING CYCLE. NOTE: If drain hose is installed, emptying the water tank is not required. See the CONNECTING THE DRAIN HOSE section in the Installation Installations of this manual.
• Pull out the water tank.
When removing the water tank from the product, hold it using both hands as it is heavy and take care not to spill any water inside the tank.
• Remove the condensed water inside the water tank. |
|
|
To avoid over filling, which could lead to water leaking outside the unit, drain |
Drain hole |
|
water left in water tank after each cycle. Over filling will cause cycle to stop |
||
prematurely until emptied. |
is on the |
|
top rear of |
||
NOTE: When the Empty Tank indicator light is on, the dryer will not operate until |
||
the drawer |
||
the tank is emptied and the indicator has been cleared. Press the Start button and |
|
|
the indicator light will turn off and the dryer will resume the cycle. |
|
Condenser
THE CONDENSER SHOULD BE CLEANED ONCE PER MONTH.
• Open the condenser compartment cover.
Unlock
• Unlock both locking tabs.
• Remove the condenser box from the condenser compartment.
•Clean the condenser box and inside the condenser compartment completely. Use tap water to clean between the grooves of the condenser box by allowing tap water to flow
through it. Reach inside the condenser compartment and wipe away all debris. Make sure the rubber gaskets on the condenser box are free of debris before reinstalling.
NOTES:
• Make sure to clean your condenser once per month to prevent degradation of the dryer’s performance.
•When assembling the condenser after cleaning it, make sure the locking tabs are set to the lock position. Never run the dryer without the condenser installed.
10 |
49-90571-3 |
Notes
<![endif]>NOTES
49-90571-3 |
11 |
Installation |
Dryer |
Instructions |
|
If you have any questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
In Canada, call 800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT– Save these instructions for local electrical inspector’s use.
• IMPORTANT– Observe all governing codes and ordinances.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Clothes dryer installation must be performed by a qualified installer.
•Before the old dryer is removed from service or discarded, remove the dryer door.
•Service information and the wiring diagram are located in the control console.
•Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered under the Warranty.
•Install the dryer where the temperature is above 50°F for satisfactory operation of the dryer control system.
WARNING - Fire Hazard
•Risk of Fire - Clothes dryer installation must be performed by a qualified installer.
•Install the clothes dryer according to these instructions and local codes.
•DO NOT install or store this appliance in any location where it could be exposed to water or weather.
•To reduce the risk of severe injury or death, follow all installation instructions.
•Save these instructions. (Installers: Be sure to leave these instructions with the customer.)
If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.
12 |
49-90571-3 |
Installation Instructions
UNPACKING YOUR DRYER
Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces
around the legs. Remove the bag containing the literature.
DRYER
DIMENSIONS
23-7/16” |
42-13/16” (108.7 cm) |
(59.5 cm) |
25-1/4” (64.1 cm) |
|
Front |
|
|
View |
*33-1/4” |
*33-1/4” |
|
(84.5 cm) |
(84.5 cm) |
Side View
*NOTE:
With leveling legs retracted: 33-1/4 (84.5 cm) With leveling legs fully extended: 33-5/8 (85.4 cm)
Stacked: 66-1/2” (168.9 cm)
ELECTRICAL CONNECTION
DIMENSIONS
20-1/2”
(52.1 cm)
30” |
Back |
|
View |
||
(76.2 cm) |
POWER CORDS
GE Appliances strongly recommends the use of factory specified parts. Select the power cord to fit your installation requirements.
Part Number |
Type |
Length |
Amperage |
WX9X2 |
3-Prong |
4 Feet |
30 |
WX9X3 |
3-Prong |
5 Feet |
30 |
WX9X4 |
3-Prong |
6 Feet |
30 |
WX9X18 |
4-Prong |
4 Feet |
30 |
WX9X19 |
4-Prong |
5 Feet |
30 |
WX9X20 |
4-Prong |
6 Feet |
30 |
Order on-line at GEApplianceparts.com today, 24 hours a day or by phone at 877.959.8688 during normal business hours. In Canada, visit your local GE Appliances parts distributor or call 800.661.1616 or
GEAppliances.ca/en/products/parts-filters-accessories.
49-90571-3 |
13 |
Installation Instructions
REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION
WARNING - Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18” (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
•Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:
0” either side 1” front and rear 1” top
•Consideration must be given to provide adequate clearance for installation and service.
•Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air opening are: 0” both sides, 1” rear and 1” top. Consideration must be given to provide adequate clearance for installation and service.
MOBILE OR MANUFACTURED HOME INSTALLATION
•Installation MUST conform to the MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24, PART 3280 or STANDARD FOR MOBILE HOMES CAN/CSA-Z240 MH, or, when such standards are not applicable, with AMERICAN NATIONAL STANDARD FOR MOBILE HOME, ANSI/NFPA NO. 501B.
•Provide an opening with a free area of at least 25 square inches for introduction of outside air into the dryer room.
•See the sections for electrical connection information.
BATHROOM OR BEDROOM INSTALLATION
The installation must conform with local codes or, in the absence of local codes, with the NATIONAL
ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric dryers).
UNDERCOUNTER INSTALLATION
If an undercounter installation is desired:
•No special dryer installation kit is required.
•If the dryer is installed alone, a minimum of 60 square inches of open area is required. If a washer and dryer are installed together, a minimum of 120 square inches of open area is required.
Dryer Installed Alone
Countertop and side cabinets
60 |
square |
inches |
min. |
open |
area |
Washer and Dryer Installed Together
Countertop and side cabinets
120 |
square |
inches |
min. |
open |
area |
14 |
49-90571-3 |
Installation Instructions
CONNECTING AN ELECTRIC DRYER
TOOLS YOU WILL NEED
Slip-joint pliers |
Phillips |
|
screwdriver |
Flat-blade |
Level |
screwdriver |
MATERIALS YOU WILL NEED
Safety glasses
Gloves
3/4” Strain relief (UL recognized)
Dryer power cord kit (not provided with dryer)
UL rated 120/240V, 30A with 3 or 4 prongs. Identify the plug type as per the house receptacle before purchasing line cord.
Stacking installations may require a power cord up to 6 feet in length.
Before making the electrical connection, turn off the circuit breaker(s) or remove the dryer’s circuit fuse(s) at the electrical box. Be sure the dryer cord is unplugged from the wall. NEVER LEAVE THE ACCESS COVER OFF THE TERMINAL BLOCK.
WARNING - Electrical Shock Hazard
Disconnect power supply before servicing. Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING - Shock Hazard
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.
Service personnel – DO NOT contact the following parts while the appliance is energized: motor start capacitor, motor metal holder, and drum wheel shaft.
49-90571-3 |
15 |
Installation Instructions
ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS
For electrical connections using a power cord:
WARNING - Fire Hazard
Use a new UL-listed 240V 30 amp dryer power supply cord with closed ring terminals or spade terminals with upturned ends.
Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal.
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining two supply wires to remaining two terminals.
Securely tighten all electrical connections. Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improper connection of the
WARNING equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded. DO NOT modify the plug on the power supply cord. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
WARNING - Electrical Shock Hazard
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER BEFORE SERVICING.
This dryer should be connected to an individual branch circuit with 10 gauge copper wire minimum through a 30 amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
ELECTRICAL CONNECTION INFORMATION FOR ELECTRIC DRYERS
For direct wire connections:
WARNING - Fire Hazard
Use 10 gauge copper wire. Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center terminal.
Ground wire (green or bare wire) must be connected to green ground connector.
Connect remaining two supply wires to remaining two terminals.
Securely tighten all electrical connections. Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
GROUNDING INSTRUCTIONS
For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal on the appliance.
Improper connection of the
WARNING equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the appliance is properly grounded.
SAVE THESE INSTRUCTIONS
WARNING - Electrical Shock Hazard
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER BEFORE SERVICING.
This dryer should be connected to an individual branch circuit with 10 gauge copper wire minimum through a 30 amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
16 |
49-90571-3 |
Installation Instructions
CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION)
NOTE: Since January 1, 1996, the National Electrical Code requires that new constructions use a 4-wire connection to an electric dryer. A 4-wire cord must also be used where local codes do not permit grounding through the neutral. 3-wire connection is NOT for use on new construction.
|
White Wire |
L1 N L2 |
|
|
Black |
|
|
or Red |
|
|
Wire |
|
Black |
|
Cover |
or |
|
|
Red |
|
|
Wire |
|
|
Green wire |
3/4” Strain |
|
from power |
Relief and |
|
cord |
Bracket |
4 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).
1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.
2.Be sure the dryer cord is unplugged from the wall receptacle.
3.Remove the power cord cover located at the upper back.
4.Remove green ground screw and retain for use in Step 7. Remove center screw (marked N) in terminal block. Remove and discard ground strap.
5.Install 3/4 in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.
6.Connect power cord as follows:
A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of the terminal block (marked N).
7.Attach ground wire of power cord with the green ground screw (hole above strain relief bracket). Tighten all terminal block screws (3) securely.
8.Properly secure power cord to strain relief and bracket.
9.Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.
CONNECTING DRYER USING 3-WIRE CONNECTION
If required, by local code, install external ground (not provided) to grounded metal, cold water pipe, or other established ground determined by a qualified electrician.
Black or Red Wire |
L1 N L2 |
White Wire
Black
or Red
Wire Cover
Ground
Strap
3/4” Strain
Relief and
Bracket
3 #10 AWG minimum copper conductors or 120/240V 30A power supply cord kit marked for use with dryers and provided with closed loop or spade terminals with upturned ends (not supplied).
3-wire Connection
Not for use in Canada.
DO NOT use for Mobile Home Installations. NOT for use on new construction.
NOT for use on recreational vehicles.
NOT for use in areas where local codes prohibit grounding through the neutral conduction.
1.Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall receptacle.
3.Remove the power cord cover located at the upper back.
4.Install 3/4-in. UL-recognized strain relief to power cord entry hole. Bring power cord through strain relief and bracket.
5.Connect power cord as follows:
A.Connect the 2 hot lines to the outer screws of the terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of the terminal block (marked N).
6. Be sure ground strap is connected to green ground screw on cabinet rear. Tighten all terminal block screws (3) securely.
7.Properly secure power cord to strain relief and bracket.
8.Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE TERMINAL BLOCK.
49-90571-3 |
17 |
Installation Instructions
CONNECTING THE DRAIN HOSE
DRAINING WATER WITHOUT USING THE WATER TANK
You can use the dryer without using the water tank by following the procedures below.
CONNECTING THE DRAIN HOSE
The dryer can pump the condensed water outside of the DRYER directly with drain hose provide.
The procedures to connect the drain hose are as follows.
Back |
View |
1. Disconnect the drain hose A.
2.Connect the drain hose A to the other hole.
3.Connect accessory hose B (long drain hose) adjacent to hose A.
A
A
B
•When connecting hose B, take care that the height of the hose does not exceed 47” (120 cm).
•After connecting the drain hose, you can now directly drain the condensed water to a standpipe or washstand.
CONNECTING THE DRAIN HOSE (CONT.)
4.Over the edge of a wash basin: The drain hose must be placed lower than 47” (120 cm) and higher than 30” (76 cm). To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose from moving.
5. Assemble the drain hose and the hose guide and fix them with the cable-tie.
Drain Hose |
Hose Guide |
47”
(120 cm)
Max.
Cable Ties
Do not push the drain hose in the standpipe any further than 4” (10 cm). Pushing the drain hose further in the standpipe can cause leaking.
18 |
49-90571-3 |
Installation Instructions
FINAL SETUP
1 LEVEL THE DRYER
Stand the dryer upright near the final location and adjust the four leveling legs at the corners to ensure that the dryer is level from side to side and front to rear.
3 DRYER STARTUP
Press the Power button.
Power
NOTE: If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing Power. Otherwise, the display will not come on.
The dryer is now ready for use.
Lower Raise
2 PLUG DRYER IN
NOTE: Stacking installations may require a power cord up to 6 feet in length.
Ensure proper ground exists before use.
49-90571-3 |
19 |
Installation Instructions
STACKING THE WASHER AND DRYER (if desired)
If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer. Kit sold separately.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT– Save these instructions for local electrical inspector’s use.
• IMPORTANT– Observe all governing codes and ordinances.
•Note to Installer – Be sure to leave these instructions with the Consumer.
•Note to Consumer – Keep these instructions for future reference.
•Service must be performed by a qualified installer.
•Do not allow children on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
•Proper installation is the responsibility of the installer.
GE APPLIANCES STACK KIT
Order on-line at GEApplianceParts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.
Part Number |
Accessory |
GFA24KITL |
Complete Stack Kit |
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air opening are: 0” both sides, 1” rear and 1” top. Consideration must be given to provide adequate clearance for installation and service.
KIT CONTENTS (GE APPLIANCES KIT # GFA24KITL)
Screws (2) Long
For dryer
attachment
|
Bracket- |
|
stack (L) |
Bracket- |
Screws (6) Short |
stack (R) |
For washer attachment |
|
REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION
WARNING - Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18” (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
•Minimum clearance between dryer cabinet and adjacent walls or other surfaces is:
0” either side 1” front and rear 1” top
•Consideration must be given to provide adequate clearance for installation and service.
•Closet doors must be louvered or otherwise ventilated and have at least 60 square inches of open area. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 square inches of open area.
TOOLS YOU WILL NEED
Phillips |
Gloves |
screwdriver |
|
Level |
|
INSTALLATION PREPARATION
Remove the packaging.
Flatten the product carton to use as a pad to lay the dryer down on its side. Continue using the carton to protect the finished floor in front of the installation location.
20 |
49-90571-3 |
Installation Instructions
INSTALLING THE STACK BRACKET KIT
1INSTALLBRACKETTOWASHER
A.Remove washer top cap screw from the rear left. Align left bracket holes with top cap screw hole on rear left of the unit and replace screw. NOTE: Leave screws loose so dryer hole alignment will be easier.
B.Drive next screw through the bracket into the rear of the washer.
C.Repeat the above steps with the right side.
Short screws into brackets and washer
Washer
Top
2INSTALL DRYER AND BRACKET ON DRYER
Disconnect power before installing. WARNING Failure to do so could result in
serious injury or death.
- Excessive Weight
WARNING Hazard
Failure to do so may result in back or other injury, or property damage.
•Use two or more people to install dryer.
•Avoid tipping and rupture of utility services.
•Dryer must be securely attached to the washer.
•DO NOT place the washer on top of the dryer.
A.Lift the dryer on top of the washer. Protect the washer control panel with cardboard or other protection. Be sure to lift the dryer high enough to clear the washer control panel.
B.Align the holes in the bracket with the holes in the back of the dryer. Using a Phillips screwdriver, attach the 2 #8 x 1/2” tapping screws.
2 |
INSTALL DRYER AND BRACKET |
|
ON DRYER (CONT.) |
C. Tighten the dryer bracket screws; then tighten all |
|
|
stacking kit screws. |
|
Long screws into |
|
brackets and dryer |
3 FINALIZE THE INSTALLATION
Do not push on the dryer once CAUTION installed to top of the washer.
Pushing on the dryer may result in pinched fingers.
A.Refer to the washer Installation Instructions to complete the washer installation.
B.Refer to the dryer Installation Instructions to complete the dryer installation.
C.Carefully slide or walk the stacked washer and dryer into place. Use felt pads or other sliding device to assist moving and to protect flooring.
Dryer
Place |
Place |
hands |
hands |
here |
here |
Washer
49-90571-3 |
21 |
Installation Instructions
REVERSING THE DOOR SWING (Optional)
IMPORTANT NOTES
• Before you start, unplug the dryer from its electrical |
• |
Once you begin, do not move the cabinet until |
outlet. |
|
door-swing reversal is completed. |
• Handle parts carefully to avoid scratching paint. |
• |
These instructions are for changing the hinges from |
• Provide a non-scratching work surface for the doors. |
|
the right side to the left side—if you ever want to |
• Tools you will need: Phillips-head screwdriver. |
|
switch them back to the right side, follow these same |
|
instructions and reverse all references to the left and |
|
|
|
|
|
|
right. |
1REMOVE THE DOOR ASSEMBLY
•Open the door. Remove the two screws holding the hinge/door assembly to the dryer. Carefully set the hinge/door assembly aside.
Hinge and Door
Assembly
Hold the Door and
Remove Hinge Screws
from the Dryer
2REMOVE, ROTATE AND REPLACE THE STRIKE PLATE
•Remove the two screws holding the strike plate. Rotate it and install it on the opposite side.
Strike Plate
and Screws
Reinstall
Strike Plate
and Screws
3REMOVE, ROTATE AND REPLACE THE INNER DOOR
•Remove the six screws securing the inner door to the outer door. Remove the inner door, rotate it 180o and reinstall it into the outer door using the same six screws.
Remove six |
|
Replace the |
screws and the |
Inner door shown |
inner door and |
inner door |
rotated 180o |
six screws |
4ROTATE AND REPLACE THE HINGE/DOOR ASSEMBLY
•Rotate and replace the hinge/door assembly, on the opposite side, using the same two screws.
Secure with same two screws
22 |
49-90571-3 |
Notes
49-90571-3 |
23 |
<![endif]>TROUBLESHOOTING TIPS
Troubleshooting Tips... Before you call for service
Problem |
Possible Cause |
What To Do |
|
Dryer shakes or |
Some shaking/noise is |
Move dryer to an even floor space, or adjust leveling legs as |
|
makes noise |
normal. Dryer may be sitting |
necessary until even. |
|
|
unevenly. |
|
|
Clothes take |
Improper sorting |
Separate heavy items from lightweight items (generally, a |
|
too long to dry |
|
well-sorted washer load is a well-sorted dryer load). |
|
|
Large loads of heavy fabrics |
Large, heavy fabrics contain more moisture and take longer to dry. |
|
|
(like beach towels) |
Separate large, heavy fabrics into smaller loads to speed drying |
|
|
|
time. |
|
|
Non-venting dryer |
Condensing dryers usually take longer to dry than a vented dryer. |
|
|
Controls improperly set |
Match control settings to the load you are drying. |
|
|
Condenser box is clogged |
Remove and clean the condenser box. Also, clean the location |
|
|
|
where the condenser box is located ensuring all seals are free |
|
|
|
from debris. Put the condenser box back and lock it in place. |
|
|
|
See Condenser in the Care and Cleaning section. |
|
|
Lint filter is full |
Clean lint filter before every load. |
|
|
Blown fuses or tripped |
Replace fuses or reset circuit breakers. Since most dryers use 2 |
|
|
circuit breaker |
fuses/breakers, make sure both are operating. |
|
|
Overloading/combining loads |
Do not put more than one washer load in the dryer at a time. |
|
|
Underloading |
If you are drying only one or two items, add a few items to ensure |
|
|
|
proper tumbling. |
|
The Dry |
Load consists of a mixture of |
When combining heavy and light fabrics in a load, choose More |
|
dryness level |
heavy and light fabrics |
Dry. |
|
was chosen |
|
|
|
Lint filter, condenser, and/or |
Inspect and clean lint filter, condenser, and/or air intake vent |
||
but load is still |
|||
air intake vent located on the |
located on the front of the dryer. |
||
damp |
|||
front of the dryer is blocked |
|
||
|
|
||
|
Dry Sensor is dirty |
Clean the sensor with a moist cloth. |
|
Control buttons |
Controls accidentally put in |
Press Start/Pause. |
|
not responding |
service mode |
|
|
|
Controls accidentally put in |
Hold the Lock Control button for 3 seconds to unlock the dryer. |
|
|
lock mode |
|
|
|
Controls performed an |
Reset the in-house breaker. |
|
|
incorrect operation |
|
|
Dryer doesn’t |
Control panel is “asleep” |
This is normal. Press Power to activate the control panel. |
|
start |
|
|
|
Dryer is unplugged |
Make sure the dryer plug is pushed completely into the outlet. |
||
|
|||
|
Fuse is blown/circuit breaker |
Check the building’s fuse/circuit breaker box and replace fuse or |
|
|
is tripped |
reset breaker. NOTE: Electric dryers use two fuses or breakers. |
|
|
Dryer was accidentally |
If the light on the Start/Pause button is flashing, the dryer is |
|
|
paused when starting Delay |
paused. Press Start/Pause to restart the countdown. |
|
|
Dry |
|
|
|
Water tank is full |
If the Empty Tank light is on, you must empty the water tank |
|
|
|
before the dryer will start. Refer to the Care and Cleaning section |
|
|
|
for instructions on emptying the water tank. |
|
No numbers |
Dryer is continuously |
This is normal. When the dryer senses a low level of moisture in |
|
displayed |
monitoring the amount of |
the load, the dryer will display the dry time remaining. |
|
during cycle, |
moisture in the clothes |
|
|
only lights |
|
|
24 |
49-90571-3 |