GE RX3i PROFINET, GFK-2737F User Manual

GE

Automation & Controls

Programmable Control Products

RX3i PROFINET IO-Scanner User Manual GFK-2737F

PACSystems*
RX3i PROFINET
IO-Scanner
User Manual

GFK-2737F

December 2016

Legal Information

Warnings, Cautions, and Notes as Used in this Publication GFL-002

Warning

Warning notices are used in this publication to emphasize that hazardous voltages,
currents, temperatures, or other conditions that could cause personal injury exist in this
equipment or may be associated with its use.

In situations where inattention could cause either personal injury or damage to
equipment, a Warning notice is used.

Caution

Caution notices are used where equipment might be damaged if care is not taken.

Note: Notes merely call attention to information that is especially significant to understanding and

operating the equipment.

These instructions do not purport to cover all details or variations in equipment, nor to provide for every
possible contingency to be met during installation, operation, and maintenance. The information is supplied
for informational purposes only, and GE makes no warranty as to the accuracy of the information included
herein. Changes, modifications, and/or improvements to equipment and specifications are made
periodically and these changes may or may not be reflected herein. It is understood that GE may make
changes, modifications, or improvements to the equipment referenced herein or to the document itself at
any time. This document is intended for trained personnel familiar with the GE products referenced herein.

GE may have patents or pending patent applications covering subject matter in this document. The
furnishing of this document does not provide any license whatsoever to any of these patents.

GE provides the following document and the information included therein as-is and without warranty of
any kind, expressed or implied, including but not limited to any implied statutory warranty of
merchantability or fitness for particular purpose.

* indicates a trademark of General Electric Company and/or its subsidiaries.

All other trademarks are the property of their respective owners.

©Copyright 2013-2016 General Electric Company.
All Rights Reserved

If you purchased this product through an Authorized Channel Partner, please contact the seller directly.

Contact Information

General Contact Information

Online technical support and GlobalCare

www.geautomation.com/support

Additional information

www.geautomation.com

Solution Provider

[e-mail]

Technical Support

If you have technical problems that cannot be resolved with the information in this manual, please
contact us by telephone or email, or on the web at www.geautomation.com

Americas

Phone

1-800-433-2682

International Americas Direct Dial

1-780-420-2010 (if toll free 800 option is unavailable)

Customer Care Email

[e-mail]

Primary language of support

English

Europe, the Middle East, and Africa

Phone

[phone]

EMEA Direct Dial

[phone] (if toll free 800 option is unavailable or
if dialing from a mobile telephone)

Customer Care Email

[e-mail]

Primary languages of support

English, French, German, Italian, Czech, Spanish

Asia Pacific

Phone

[phone]

[phone] (India, Indonesia, and Pakistan)

Customer Care Email

[e-mail]

[e-mail] (China)

GFK-2737F December 2016 i

Table of Contents

RX3i PROFINET IO-Scanner User Manual GFK-2737F

Table of Contents ............................................................................................................................................... i

Table of Figures ................................................................................................................................................ iv

Chapter 1 Introduction ............................................................................................................................ 1

1.1 Revisions in this Manual .............................................................................................................. 3

1.2 RX3i PROFINET Scanner Specifications ..................................................................................... 4

1.3 RX3i PROFINET Scanner Controls and Indicators ................................................................... 5

1.3.1 LEDs on the PROFINET Scanner Module ..................................................................................................................... 6

1.3.2 SD Card Slot ............................................................................................................................................................................... 6

1.3.3 Pushbutton ................................................................................................................................................................................. 6

1.3.4 USB Port ....................................................................................................................................................................................... 6

1.3.5 Ethernet Port Connections ................................................................................................................................................. 6

1.4 PROFINET Communications ........................................................................................................ 7

1.4.1 Notes on Available PROFINET Controllers .................................................................................................................. 7

1.4.2 Operations of the PROFINET Scanner .......................................................................................................................... 8

1.5 PROFINET Redundant Media ....................................................................................................... 9

1.6 System Limits .............................................................................................................................. 10

1.7 Supported Modules, Power Supplies and Backplanes ......................................................... 11

1.8 Glossary ........................................................................................................................................ 16

1.9 Documentation ........................................................................................................................... 18

Chapter 2 LED Operation and Connector Details ............................................................................. 19

2.1 Normal Operation of Individual LEDs ..................................................................................... 20

2.1.1 OK LED........................................................................................................................................................................................ 20

2.1.2 LAN LED ..................................................................................................................................................................................... 20

2.1.3 Status LED ................................................................................................................................................................................ 20

2.1.4 CONN LED................................................................................................................................................................................. 20

2.1.5 Port LEDs ................................................................................................................................................................................... 21

2.1.6 Active LED ................................................................................................................................................................................. 21

2.1.7 USB LED ..................................................................................................................................................................................... 21

2.1.8 Special LED Blink Patterns ............................................................................................................................................... 21

Contents

ii PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

2.2 Ethernet Network Ports ............................................................................................................. 24

2.3 SD Card Slot ................................................................................................................................. 25

2.4 USB Port ........................................................................................................................................ 26

Chapter 3 Installation ............................................................................................................................ 27

3.1 Pre-Installation Check ............................................................................................................... 28

3.2 Installation in Hazardous Areas............................................................................................... 29

3.2.1 ATEX Marking .......................................................................................................................................................................... 29

3.3 Module Installation ..................................................................................................................... 30

3.3.1 Power Requiremnents ....................................................................................................................................................... 30

3.3.2 Hot Insertion and Removal ............................................................................................................................................. 30

3.3.3 Removing the Backplane Knockout ........................................................................................................................... 30

3.3.4 Module Installation .............................................................................................................................................................. 31

3.3.5 Module Removal ................................................................................................................................................................... 31

3.4 Replacing a PROFINET Scanner ................................................................................................ 32

3.4.1 Method 1 – Using the SD Card ...................................................................................................................................... 32

3.4.2 Method 2 – Using the DCP Tool .................................................................................................................................... 32

3.5 SFP Modules for Ethernet Ports................................................................................................ 33

3.6 External Switch VLAN Priority Settings ................................................................................... 33

3.7 Installing the USB Port Driver ................................................................................................... 33

3.8 Firmware Updates ...................................................................................................................... 33

Chapter 4 Configuration ........................................................................................................................ 35

4.1 Configuration Overview ............................................................................................................ 36

4.1.1 Basic Configuration Steps ............................................................................................................................................... 36

4.1.2 Configuration Tool ............................................................................................................................................................... 36

4.2 Adding an IO-Device to a PROFINET LAN ............................................................................... 37

4.2.1 Adding an RX3i PROFINET Scanner to the PROFINET LAN .............................................................................. 37

4.2.2 Configuring an RX3i PROFINET Scanner .................................................................................................................. 38

4.2.3 Adding RX3i Modules .......................................................................................................................................................... 40

4.2.4 Support for Analog Modules with HART Features............................................................................................... 44

4.2.5 Configuring Module Parameters .................................................................................................................................. 44

4.3 Assigning Device Names ........................................................................................................... 48

4.3.1 Transferring the Device Name with an SD Card .................................................................................................. 48

Contents

GFK-2737F December 2016 iii

4.4 After the Configuration is Stored to the PROFINET Controller........................................... 49

Chapter 5 Operations ............................................................................................................................. 51

5.1 Power-up ...................................................................................................................................... 52

5.2 I/O Scanning ................................................................................................................................ 53

5.2.1 PROFINET Scanner Status and Control Data ......................................................................................................... 53

5.2.2 Data Coherency .................................................................................................................................................................... 54

5.2.3 Sampling Rate ........................................................................................................................................................................ 54

5.2.4 Differences from Main (CPU) Rack ............................................................................................................................... 54

5.2.5 Output Control ....................................................................................................................................................................... 55

5.3 Hot Swap of I/O Modules ........................................................................................................... 56

Chapter 6 Diagnostics ........................................................................................................................... 57

6.1 Configuration Faults .................................................................................................................. 58

6.2 Version Information ................................................................................................................... 59

6.3 Fatal Error Handling ................................................................................................................... 60

6.4 Connection Troubleshooting .................................................................................................... 61

Appendix A PROFINET Specifications .......................................................................................................... 63

A-1 PROFINET Protocol Support ................................................................................................................... 63

A-2 Technical Data .......................................................................................................................................... 63

A-3 Limitations ................................................................................................................................................ 64

A-3.1 PACSystems Features ........................................................................................................................................................ 64

A-3.2 PROFINET Features .............................................................................................................................................................. 64

Contents

iv PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

Table of Figures

Figure 1: Front View IC695PNS001 ___________________________________________________________________ 5
Figure 2: Ethernet Port Connectors on IC695PNS001 _____________________________________________________ 6
Figure 3: IC695PNS001 LEDs _______________________________________________________________________ 23
Figure 4: Underside of IC695PNS001 Showing Ethernet Ports _____________________________________________ 24
Figure 5: RX3i Backplane showing Removable Plastic Knockout ___________________________________________ 30
Figure 6: Install Module into RX3i Backplane __________________________________________________________ 31
Figure 7: Remove Module from RX3i Backplane ________________________________________________________ 31
Figure 8: Select System Redundancy Parameters in PME _________________________________________________ 39
Figure 9: Change Submodule List produces list of Eligible SFP Modules _____________________________________ 40
Figure 10: Analog Module with Configurable Parameters ________________________________________________ 42
Figure 11: Analog Module with Multiple Possible Option Settings __________________________________________ 43

GFK-2737F December 2016 1

Chapter 1 Introduction

This chapter provides an overview of the PACSystems RX3i PROFINET Scanner (PNS) module and its
operation. The last two pages of this chapter are a glossary that summarizes many terms used in the
manual.

Chapter 2, LED Operation and Connector Details, provides detailed description of the module’s indicators
and ports

Chapter 3, Installation, gives instructions for PNS module installation and replacing a PNS module.
Provides information for selecting SFP modules and network cabling and connectors.

Chapter 4, Configuration, describes how to configure the RX3i PROFINET Scanner and its associated IO­devices.

Chapter 5, Operations, describes powering up and restarting the RX3i PROFINET Scanner, the input status
data, replacing I/O modules while scanning, and how to update the firmware.

Chapter 6, Diagnostics, describes configuration faults, how to check the RX3i PROFINET Scanner version
information, fatal error handling, and some common troubleshooting suggestions.

Appendix A, PROFINET Specifications, summarizes the features specified for PROFINET v2.3 Class A IO­Devices that are supported by the RX3i PROFINET Scanner module

Chapter 1. Introduction

2 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

The PACSystems RX3i PROFINET Scanner (PNS) module, IC695PNS001, connects a remote universal RX3i
I/O rack of Series 90-30 or RX3i modules to a PROFINET I/O Controller. The PROFINET Scanner scans the
modules in its rack, retrieving input data and providing output data, and exchanges that data on the
PROFINET I/O LAN at the configured production rate.

The PNS manages PROFINET communication and module configuration between an I/O Controller and
modules in the remote rack. If network communications are lost, the PNS manages I/O states according
to the individual module configurations.

The PNS supports 10/100/1000 Mbps Copper, 100/1000 Mbps Multi-mode Fiber, and 100/1000 Mbps
Single-mode Fiber. PROFINET communications on the network require 100 or 1000 Mbps link speed.
Although 10 Mbps cannot be used for PROFINET communications, 10 Mbps can be used for other types of
Ethernet traffic such as PING. Features of the RX3i PNS include:

 Full programming and configuration services for all supported Series 90-30 and RX3i I/O Modules

using Proficy* Machine Edition. For a list of currently supported I/O modules, refer to the Important
Product Information (IPI) document provided with the firmware version on your PNS module.

 Support for daisy-chain/line, star, or ring (redundant media) topologies.
 Four switched Ethernet ports - two 8-conductor RJ45 shielded twisted pair 10/100/1000 Mbps copper

interfaces and two Small Form-factor Pluggable (SFP) cages for user-supplied SFP devices.

 The network can include media interfaces of more than one type.
 Support for transfer of IO-Device Name to another PNS module using an SD card. This eliminates the

need to connect a configuration tool, such as Proficy Machine Edition when replacing a module.

 A USB port for field updates of firmware using WinLoader.

Note: The USB port is for firmware upgrades only. It is not intended for permanent connection.

Chapter 1. Introduction

GFK-2737F December 2016 3

1.1 Revisions in this Manual

Rev

Date

Description

F

Dec­2016

• Updates for CPE400 (new related product).

• Updated list of supported I/O Modules in Section 1.7 per GFK-2738L

• Added footnotes tracking PNS firmware support for various I/O modules.

• Added footnotes tracking PNS firmware support for various features, such as HART Pass

Through.

• Added note on support for Remote Get HART Device Information COMMREQ.

E

Apr­2015

In Section 1.7, corrected data for IC695SPF010 in table

D

May­2014

 In Section 4.2.5, Configuring Module Parameters, added Universal Analog Input Module and

Power Sync and Measurement Module and related rules to the table,

 In Section 4.2.5.1, RX3i PROFINET Scanner Configuration Validation, added IC695ALG600 to the

table.

Chapter 1. Introduction

4 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

1.2 RX3i PROFINET Scanner Specifications

PROFINET Support

PROFINET Version 2.3 Class A IO-Device
Redundantly controlled operation conforms to PROFINET V2.3 Type S-2 System
Redundancy.

Controller CPU Version
Required

RX3i CPU315/CPU320 with firmware version 7.10 or later RX3i CPE305/CPE310 with
firmware version 7.10 or later RXi Controller with firmware version 7.80 or later

Proficy Machine Edition
Version Required

Version 8.0 or later

Power Requirements

3.3 Vdc:

1.2 A with no SFP devices installed

1.9 A maximum (two SFP devices installed, 0.35 A per SFP)

5 Vdc:

1.1 A maximum

Operating Temperature
Range

0 to 60°C De-rated to 57°C:

• If 100 Mbps Fiber SFPs installed, or

• If Copper SFPs operating at 1 Gbps

Number of Port
Connectors

Two RJ45 and Two SFP Cages
(SFP devices not included, available separately.)

USB Connector (for
firmware upgrades)

One Micro-B connector. USB 2.0 compliant running at Full-speed
(12 MHz)

SD Card

Supports SD and SDHC cards.

PNS Status and
Control Bits

32 input status bits and 32 output control bits

PROFINET I/O
production rate (ms)
(I/O Update Rate)

Configurable selections: 1, 2, 4, 8, 16, 32, 64, 128, 256 or 512 ms

Number of IP Addresses

Five. One per external port and one internal.

I/O Station Maximum
Limits

Number of
I/O Modules
per station

Number of backplane slots in the host RX3i rack
less one for PNS001 module itself
less the number of slots occupied by the RX3i power supply

I/O data
per station

2880 bytes total
1440 bytes of input data
1440 bytes of output data

Configuration

V2.3 GSDML file.
The file is included with Proficy Machine Edition; available for import into 3rd-Party tools.

Note: Configuration software that supports GSDML V2.3 MenuList elements (such as

Proficy Machine Edition 8.0 or later) is required to display the configuration
parameters of most IC695xxx I/O modules.

For product standards, general operating specifications, and installation requirements, refer to the
PACSystems RX3i System Manual, GFK-2314

Chapter 1. Introduction

GFK-2737F December 2016 5

1.3 RX3i PROFINET Scanner Controls and Indicators

Figure 1: Front View IC695PNS001

Chapter 1. Introduction

6 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

1.3.1 LEDs on the PROFINET Scanner Module

LEDs provide an immediate visual indication of the operational state of the PNS and port link status. The
LEDs and their operation are described in Chapter 2 LED Operation and Connector Details.

1.3.2 SD Card Slot

The SD Card Slot supports an SD or SDHC card. It can be used to transfer the IO-Device Name to another
PROFINET Scanner Module unit without a configuration tool such as Proficy Machine Edition.

1.3.3 Pushbutton

The pushbutton adjacent to the USB port is reserved for future use.

1.3.4 USB Port

The USB Port is used for installing new firmware using the WinLoader tool.

1.3.5 Ethernet Port Connections

Each port on an RX3i PNS operates independently, so devices that operate at different speeds and/or
duplex modes may be attached to the ports. By default, all ports, including empty, unconfigured SFP
cages, are set for Automatic, which enables auto negotiation for the widest range of options supported by
the port.

Figure 2: Ethernet Port Connectors on IC695PNS001

Connections to the PROFINET Scanner can be made using standard Cat 5e/6 Ethernet cables. Different
devices on the same network can be connected using the multiple ports on the RX3i PNS (Figure 2).

For other options, refer to Chapter 4, the section Adding and Configuring an Ethernet Port.

Chapter 1. Introduction

GFK-2737F December 2016 7

1.4 PROFINET Communications

For a full discussion of PROFINET Communications and interactions with the controlling RX3i CPU, refer to
Chapter 4 of the PACSystems RX3i PROFINET Controller User Manual, GFK-2571. The following topics are
covered:

 PROFINET Operation Overview

 PROFINET Communications
 Application Relationships
 Types of PROFINET Communications

 Operations of the PROFINET Controller in the RX3i System

 Duplicate PROFINET Device IP Address
 Duplicate PROFINET Controller IP Address
 Resolving Duplicate IP Addresses

 I/O Scanning
 Data Coherency
 Performance Factors
 PROFINET IO Update Rate Configuration
 RX3i CPU Operations for PROFINET

 Reference ID Variables for the RX3i Application
 PNIO_DEV_COMM Function Block
 Reset Smart Module for the PROFINET Controller
 DO I/O for Remote IO Modules
 Scan Set I/O for Remote I/O Modules
 RX3i CPU Defaults - Inputs
 RX3i CPU Defaults – Outputs

1.4.1 Notes on Available PROFINET Controllers

Each PROFINET I/O Network is controlled by one or more PROFINET I/O Controllers. PROFINET I/O
Controllers may be GE products or third-party products.

GE Automation and Control offers the following RX3i PROFINET Controllers:

 IC695PNC001: this is a rack-based intelligent module located in a slot of the host RX3i CPU rack.

The host CPU may be equipped with a maximum of four IC695PNC001 modules.

 The IC695CPE330 provides an optional embedded PROFINET Controller. To utilize this feature,

LAN2 must be configured as a PROFINET Controller. In addition, the IC695CPE330 may host a
maximum of four IC695PNC001 modules in its CPU rack.

 The IC695CPE400 also provides an optional embedded PROFINET Controller. To utilize this feature,

LAN2 must be configured as a PROFINET Controller. Since the IC695CPE400 is a Rackless CPU, it
cannot host any IC695PNC001 modules.

Each of the RX3i PROFINET Controllers mentioned above is capable of controlling a PROFINET I/O Network
containing PROFINET Scanners supplied by GE or by third-party vendors. Many vendors also supply I/O
devices that connect directly to the PROFINET network.

For PROFINET Controller product details, refer to the PACSystems RX3i PROFINET Controller User Manual,
GFK-2571.

Chapter 1. Introduction

8 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

1.4.2 Operations of the PROFINET Scanner

The RX3i PROFINET Scanner (PNS) is the head-end unit responsible for monitoring and controlling I/O
modules installed in its RX3i I/O rack. All PROFINET communications are passed between the PROFINET I/O
Controller and the PNS. The PNS is one type of IO-Device the PROFINET I/O Controller expects to
encounter. Other third-party IO-Devices may also be present on the PROFINET network.

A PNS will normally be present on a PROFINET network controlled by an RX3i PROFINET Controller (PNC).
However, it is possible to use a PNS in conjunction with any qualified PROFINET I/O Controller.

The RX3i PNS performs the following operations:

 Consumes PROFINET IO-Device configuration from the PROFINET IO-Controller over the PROFINET

network and applies it to its modules.

 Scans input data from each module it manages and produces that data to the PROFINET

IO-Controller.

 Consumes the output data that it receives from the PROFINET IO-Controller and applies it to each

module it manages.

GE Automation and Control offers the following types of PROFINET Scanners:

 IC695PNS001: the RX3i PROFINET Scanner. It may control a sub-set of RX3i I/O modules located in

the same RX3i I/O rack. This product is discussed in detail in this manual.

 IC695CEP001: a PROFINET Scanner which may control a sub-set of RX3i I/O modules in a remote

I/O drop. For product details, refer to the PACSystems RX3i CEP PROFINET Scanner User Manual,
GFK-2883.

Chapter 1. Introduction

GFK-2737F December 2016 9

1.5 PROFINET Redundant Media

For a full discussion of PROFINET Redundant Media and interactions with the controlling RX3i CPU, refer to
Chapter 6 of the PACSystems RX3i PROFINET Controller User Manual, GFK-2571. The following topics are
covered:

 PROFINET Media Redundancy Protocol

 MRP Failover Performance
 Bumpless Operation with MRP
 MRP Operation for I/O Update Rates of 16ms or Greater
 MRP Operation at I/O Update Rates Less Than 16ms
 Minimum I/O Rate When Configured in an MRP Ring
 Minimum I/O Update Rates for Bumpless Operation in a Ring Topology
 Third-party MRP Manager Use with PNC as MRP Client

 Ring Topology with One Controller
 Ring Topology with Multiple Controllers
 Setting Up Media Redundancy Protocol

 Media Redundancy Setup for a PROFINET I/O Controller

 Sequence for Enabling Media Redundancy
 Sequence for Replacing a Media Redundancy Manager
 Procedure for Disabling Media Redundancy

Chapter 1. Introduction

10 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

1.6 System Limits

I/O Controllers will have limitations on the system they support. One of these limits is the number of
PROFINET submodules supported. In the RX3i PNS rack, each power supply or I/O module is represented
by one PROFINET submodule. The RX3i PNS uses four to six submodules:

• two submodules for basic operation of the PNS module

• two built-in port submodules that are always configured

• up to two additional port submodules, one for each optional Ethernet port configured

Other limitations, such as the configuration and I/O sizes, are specific to the configuration options chosen.
Note that not every combination of options is supported in every system.

If the configuration uses all slots in every device with a large device count, the memory of the I/O
Controller system will be a limiting resource.

Chapter 1. Introduction

GFK-2737F December 2016 11

1.7 Supported Modules, Power Supplies and Backplanes

For an updated list of modules, power supplies and backplanes that can be used with an RX3i PROFINET
Scanner, refer to the most recent version of the PACSystems RX3i PROFINET Scanner Important Product
Information, GFK-2738. The list below was published in GFK-2738L (June 2016).

Catalog Number

Module Description

Distinguishing Classes1

Discrete Input Modules

IC693ACC300

Input Simulator Module (8-pt & 16-pt operation)

8 in, 16 in

IC693MDL230

8-Circuit Input 120 Vac Isolated

8 in

IC693MDL231

8-Circuit Input 240 Vac Isolated

8 in

IC693MDL240

16-Circuit Input 120 Vac

16 in

IC693MDL241

16-Circuit Input 24 Vac / Vdc

16 in

IC693MDL250

16-Circuit Isolated Input 120 Vac, Input Filtering Off

16 in

IC693MDL250

16-Circuit Isolated Input 120 Vac, Input Filtering On

none

IC693MDL260

32-Circuit Input 120 Vac, Input Filtering Off

32 in

IC693MDL260

32-Circuit Input 120 Vac, Input Filtering On

32 in/out

IC693MDL632

8-Circuit Input 125 Vdc Positive / Negative Logic

8 in

IC693MDL634

8-Circuit Input 24 Vdc Positive / Negative Logic

8 in

IC693MDL635

16-Circuit Input 125 Vdc Positive / Negative Logic

16 in

IC693MDL645

16-Circuit Input 24 Vdc Positive / Negative Logic

16 in

IC693MDL646

16-Circuit Input 24 Vdc Positive / Negative Logic Fast

16 in

IC693MDL648

16-Circuit Input 48 Vdc Positive / Negative Logic Fast

16 in

IC693MDL654

32-Circuit Input 5/12 Vdc Positive / Negative Logic

32 in

IC693MDL655

32-Circuit Input 24 Vdc Positive / Negative Logic Fast

32 in

IC693MDL660

32-Circuit Input 24 Vdc Positive / Negative Logic, Input Filtering Off

32 in

IC693MDL660

32-Circuit Input 24 Vdc Positive / Negative Logic, Input Filtering On

32 in/out

IC694ACC300

Input Simulator Module (8-pt & 16-pt Mode)

8 in, 16 in

IC694MDL230

8-Circuit Input 120 Vac Isolated

8 in

IC694MDL231

8-Circuit Input 240 Vac Isolated

8 in

IC694MDL240

16-Circuit Input 120 Vac

16 in

IC694MDL241

16-Circuit Input 24 Vac / Vdc

16 in

1

The PNS001 cannot distinguish between modules within the same Distinguishing Class type. This means that any module

physically present that is within the same class as the one configured will not alert the user with a System Configuration
Mismatch fault on the Controller Fault Table. Refer to the section entitled CPU operation during System Configuration Mismatch
Faults in PACSystems RX7i and RX3i CPU Reference Manual, GFK-2222.

Chapter 1. Introduction

12 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

Catalog Number

Module Description

Distinguishing Classes1

IC694MDL250

16-Circuit Input 120 Vac Isolated

none

IC694MDL260

32-Circuit Input 120 Vac

none

IC694MDL632

8-Circuit Input 125 Vdc Positive / Negative Logic

8 in

IC694MDL634

8-Circuit Input 24 Vdc Positive / Negative Logic

8 in

IC694MDL635

16-Circuit Input 125 Vdc Positive / Negative Logic

16 in

IC694MDL645

16-Circuit Input 24 Vdc Positive / Negative Logic

16 in

IC694MDL646

16-Circuit Input 24 Vdc Positive / Negative Logic Fast

16 in

IC694MDL654

32-Circuit Input 5/12 Vdc Positive / Negative Logic

32 in

IC694MDL655

32-Circuit Input 24 Vdc Positive / Negative Logic Fast

32 in

IC694MDL658

32-Circuit Input 48 Vdc Positive / Negative Logic Fast

32 in

IC694MDL660

32-Circuit Input 24 Vdc Positive / Negative Logic

none

IC695MDL664

16-Circuit Smart Input 24 Vdc Positive Logic2

none

Discrete Output Modules

IC693MDL310

12-Circuit Output 120 Vac 0.5A

16 out

IC693MDL330

8-Circuit Output 120/240 Vac 2A

8 out

IC693MDL340

16-Circuit Output 120 Vac 0.5A

16 out

IC693MDL350

16-Circuit Output 120/240 Vac Isolated

16 out

IC693MDL390

5-Circuit Output 120/240 Vac 2A Isolated

8 out

IC693MDL730

8-Circuit Output 12/24 Vdc 2A Positive

8 out

IC693MDL731

8-Circuit Output 12/24 Vdc 2A Negative

8 out

IC693MDL732

8-Circuit Output 12/24 Vdc 0.5A Positive

8 out

IC693MDL733

8-Circuit Output 12/24 Vdc 0.5A Negative

8 out

IC693MDL734

6-Circuit Output 125 Vdc 1A Positive/Negative

8 out

IC693MDL740

16-Circuit Output 12/24 Vdc 0.5A Positive

16 out

IC693MDL741

16-Circuit Output 12/24 Vdc 0.5A Negative

16 out

IC693MDL742

16-Circuit Output 12/24 Vdc 1A Positive

16 out

IC693MDL748

8-Circuit Output 48 Vdc 0.5A Positive

8 out

IC693MDL752

32-Circuit Output 5/24 Vdc 0.5A Negative

32 out

IC693MDL753

32-Circuit Output 12/24 Vdc 0.5A Positive

32 out

IC693MDL754

32-Circuit Output 24 Vdc 0.75A Positive with ESCP, Diagnostics Off

32 out

IC693MDL754

32-Circuit Output 24 Vdc 0.75A Positive with ESCP, Diagnostics On

32 in/out

2

The PNS001 currently does not support Fault Reporting from this module.

Chapter 1. Introduction

GFK-2737F December 2016 13

Catalog Number

Module Description

Distinguishing Classes1

IC693MDL758

32-Circuit Output 12/24 Vdc 0.5A Positive with ESCP

2,3

32 out

IC693MDL760

Solenoid Valve Output Module

16 out

IC693MDL916

16-Circuit Output 4A Relay

16 out

IC693MDL930

8-Circuit Output 4A Relay Isolated

8 out

IC693MDL931

8-Circuit Output Relay Form BC Isolated

8 out

IC693MDL940

16-Circuit Output 2A Relay

16 out

IC694MDL310

12-Circuit Output 120 Vac 0.5A

16 out

IC694MDL330

8-Circuit Output 120/240 Vac 2A

8 out

IC694MDL340

16-Circuit Output 120 Vac 0.5A

16 out

IC694MDL350

16-Circuit Output 120/240 Vac Isolated

none

IC694MDL390

5-Circuit Output 120/240 Vac 2A Isolated

8 out

IC694MDL732

8-Circuit Output 12/24 Vdc 2A Positive

8 out

IC694MDL734

6-Circuit Output 125 Vdc 1A Positive/Negative

8 out

IC694MDL740

16-Circuit Output 12/24 Vdc 0.5A Positive

16 out

IC694MDL741

16-Circuit Output 12/24 Vdc 1A Negative

16 out

IC694MDL742

16-Circuit Output 12/24 Vdc 1A Positive

16 out

IC694MDL752

32-Circuit Output 5/24 Vdc 0.5A Negative

32 out

IC694MDL753

32-Circuit Output 12/24 Vdc 0.5A Positive

32 out

IC694MDL754

32-Circuit Output with ESCP

none

IC694MDL758

32-Circuit Output 12/24 Vdc 0.5A Positive with ESCP2

none

IC694MDL916

16-Circuit Output 4A Relay

none

IC694MDL930

8-Circuit Output 4A Relay Isolated

8 out

IC694MDL931

8-Circuit Output Relay Form BC Isolated

8 out

IC694MDL940

16-Circuit Output 2A Relay

16 out

IC695MDL765

16-Circuit Smart Output 24/125 Vdc 2A Positive Logic2

None

Discrete Mixed Modules

IC693MAR590

8-Circuit Mixed 120 Vac Input / Relay Output

8 in/out

IC693MDR390

8-Circuit Mixed 24 Vdc Input / Relay Output

8 in/out

Analog Input Modules

IC693ALG220

4-Point Analog Voltage Input

ALG IN 4

IC693ALG221

4-Point Analog Current Input

ALG IN 4

IC693ALG222

16-Point Analog Voltage Input

ALG IN 16

IC693ALG223

16-Point Analog Current Input

ALG IN 16

Chapter 1. Introduction

14 PACSystems* RX3i PROFINET IO-Scanner User Manual GFK-2737F

Catalog Number

Module Description

Distinguishing Classes1

IC694ALG220

4-Point Analog Voltage Input

ALG IN 4

IC694ALG221

4-Point Analog Current Input

ALG IN 4

IC694ALG222

16-Point Analog Voltage Input

ALG IN 16

IC694ALG223

16-Point Analog Current Input

ALG IN 16

IC695ALG106

6-Point Isolated Analog Input Current/Voltage

3,4

none

IC695ALG112

12-Point Isolated Analog Current/Voltage Input4

none

IC695ALG600

8-Point Universal Analog Input Module4

none

IC695ALG608

8-Point Analog Input Current / Voltage Input

3, 4

none

IC695ALG616

16-Point Analog Current / Voltage Input4

none

IC695ALG626

16-Point Analog Current / Voltage Input4 (HART5 Support)

none

IC695ALG628

8-Point Analog Current / Voltage Input

3, 4

(HART5 Support)

none

Analog Output Modules

IC693ALG390

2-Point Analog Voltage Output

ALG OUT 2

IC693ALG391

2-Point Analog Current Output

ALG OUT 2

IC693ALG392

8-Point Analog Current / Voltage Output

ALG OUT 8

IC694ALG390

2-Point Analog Voltage Output

ALG OUT 2

IC694ALG391

2-Point Analog Current Output

ALG OUT 2

IC694ALG392

8-Point Analog Current / Voltage Output

ALG OUT 8

IC695ALG704

4-Point Analog Current / Voltage Output

3, 4

none

IC695ALG708

8-Point Analog Current / Voltage Output4

none

IC695ALG728

8-Point Analog Current / Voltage Output4 (HART5 Support)

none

IC695ALG808

8-Point Isolated Analog Current / Voltage Output4

none

Analog Mixed Modules

IC693ALG442

4-Input / 2-Output, Current / Voltage

ALG IN 4, ALG OUT 2

IC694ALG442

4-Input / 2-Output, Current / Voltage

ALG IN 4, ALG OUT 2

RTD Input Modules

IC695ALG508

8-Channel Isolated RTD Input4

none

Thermocouple Input Modules

IC695ALG312

12-Point Isolated Thermocouple Input

3, 4

none

IC695ALG412

12-Point Isolated High Speed Thermocouple Input

3, 4

none

3

PNS001 firmware version 2.40 required for this product.

4

PNS001 currently does not support Fault Reporting or Interrupts from this module.

5

PNS001 firmware version 2.30 supports the HART Pass Through capabilities of this module. HART-compatible PNC001 and CPU

versions are also required.

Chapter 1. Introduction

GFK-2737F December 2016 15

Catalog Number

Module Description

Distinguishing Classes1

High-Speed Counter Modules

IC695HSC308

High-Speed Counter Module - 8 Counters4

None

Specialty Modules

IC694PSM001

Power Sync and Measurement Module

none

Power Supply Modules

IC695PSA040

Universal 120/240 Vac, 125Vdc 40W Power Supply

none

IC695PSA140

Multifunctional 120/240 Vac, 125Vdc 40W Power Supply

none

IC695PSD040

24Vdc 40W Power Supply

none

IC695PSD140

Multifunctional 24Vdc 40W Power Supply

none

Small Form-Factor Pluggable (SFP) Modules

IC695SPC100

10/100/1000Base-T Copper SFP

none

IC695SPF002

100Base-FX (fiber 2km) SFP

none

IC695SPF010

1000Base-LX (fiber 10km) SFP

none

IC695SPF550

1000Base-SX (fiber 550m) SFP

none