GE GFB700F, GFC700F, GFC1000F, GFC500F User Manual

Disposall

Food Waste Disposer

www.GEAppliances.com

Owner’s Manual

& Installation

Instructions

165D4700P229 49-5903 01-01 JR 560C460P01 Rev. A

Safety Information

Connecting Electricity . . . . . . 2, 3

Safety Precautions . . . . . . . . . . . 2

Installation Instructions

Attaching the Discharge

Elbow . . . . . . . . . . . . . . . . . . . . . . 6

Components and Installation

of Sink Flange . . . . . . . . . . . . . . . 5

Connecting Disposer to

Sink Flange . . . . . . . . . . . . . . . . . .7

Dimensions/Typical

Installations . . . . . . . . . . . . . . . . .8

Dishwasher Connection . . . . . . . 6

Operating Instructions

Batch Feed Models . . . . . . . . . . .9

Care and Maintenance . . . . . . .10

Continuous Feed Models . . . . . .9

Troubleshooting Tips

Before You Call for

Service . . . . . . . . . . . . . . . . . . . . .11

Customer Service

Warranty . . . . . . . . . . . . . . . . . . 12

Write the model and serial numbers for your disposall here:

Model #______________________

Serial # ______________________

You can find them on a label on the bottom of the disposer.

Model Line Series

GFC300F GFC500F GFC700F

GFB700F GFC1000F GFB1000F

WARNING!

When using electrical appliances, basic safety precautions should be followed, including the following:

SAFETY PRECAUTIONS

■

■Use this appliance only for its intended

purpose as described in this Owner’s Manual.

■

■Read all the instructions before using the

appliance.

■

■To reduce the risk of injury, close supervision is

required when an appliance is used near children.

■

■Do not put fingers or hands into a waste

disposer.

■

■Turn the power switch to the off position before

attempting to clear a jam or remove an object from the disposer.

■

■When attempting to loosen a jam in a waste

disposer, use a long wooden object such as a wooden spoon or the wooden handle of a broom or mop.

■

■When attempting to remove objects from a

waste disposer, use long-handled tongs or pliers. If the disposer is magnetically actuated, use only nonmagnetic tools.

■

■To reduce the risk of injury by materials that may

be expelled by a waste disposer, do not put the following into a disposer:

a) Clam or oyster shells.

b) Caustic drain cleaners or similar products.

c) Glass, china or plastic.

d) Large whole bones.

e) Metal, such as bottle caps, tin cans, utensils

or aluminum foil.

f) Hot grease or other hot liquids.

g) Whole corn husks.

■

■When not operating a disposer, leave the drain

stopper in place to reduce the risk of objects falling into the disposer.

■

For proper grounding instructions see the ELECTRICAL CONNECTION portion of this manual.

Consumer Support Troubleshooting Tips Operating Instructions Installation Instructions Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS. READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

If you are not familiar with electrical power and procedures, call a qualified electrician.

DANGER:

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

For Models Equipped with a Grounded Cord:

GROUNDING INSTRUCTIONS:

This appliance must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS

The power cord and/or connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances.

For Models Not Equipped with a Cord:

If your disposer does not come equipped with a cord, you can connect it in two ways:

1. Attach a power cord, minimum 18″ in length and not to exceed 36″ in length.

2. Wire the disposer directly into the house

current.

To Attach a Power Cord:

GROUNDING INSTRUCTIONS:

This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The power cord (to be installed) must have an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER:

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.

NOTE: Disconnect electric power to disposer circuit before installation. Turn the circuit breaker to the OFF position or remove the fuse.

A. Connect the disposer to 110–120 Volt, 60 Hz

AC current only.

B. If a plug-in

cord is used, use a threeprong plug. Ground wire should be attached to the ground screw in the bottom of the disposer (end bell).

Use a cable clamp strain relief connector where power cord enters the disposer.

To Wire Your Disposer Directly into the House Current:

GROUNDING INSTRUCTIONS:

This appliance must be connected to a grounded, metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

A. If you use BX cable:

1. Install the cable connector in the hole.

2. Connect white wire to white lead of disposer.

3. Connect black wire.

4. Connect bare ground wire.

If BX cable is not used, provide a separate ground wire to nearest reliable ground, using the screw in the end bell for the ground wire.

B. If your power supply does not include a ground

wire, you must provide one unless metal cable is used. Attach a copper wire securely to disposer ground screw and attach other end of wire to a reliable ground. Use only UL approved ground clamp. If plastic pipe is used in your home, a qualified electrician should install a proper ground.

Trace lead connected to this blade and attach that lead to white wire on disposer.

Ribbed Side

NOTE: When viewing face of electrical plug with grounding pin at top, the larger left blade is connected to the identified wire.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting Tips

Installation Instructions

Safety Instructions Operating Instructions

IMPORTANT SAFETY INSTRUCTIONS. READ ALL INSTRUCTIONS BEFORE USING.

www.GEAppliances.com

Strain Relief

Nut

Red Reset Button

Ground Screw

Wire Nuts

Remove Cover Plate

To House Current or Power Cord

WARNING!

HOW TO CONNECT ELECTRICITY (cont.)

If you are not familiar with electrical power and procedures, call a qualified electrician.

Bottom of the Disposer (end bell)

ADDITIONAL MATERIALS YOU MAY NEED

• Steel punch or wooden dowel

• Petroleum jelly or liquid soap

• Hose clamp

• Dishwasher drain connector

• Adjustable pipe wrench

• Plumber’s putty (for cast sinks)

• Stepped rubber drain adapter

• Wire nuts

• Cable connector

• Flexible drain pipe

• Power cord kit (Part Number PM3X215GDS)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT

–

Save these

instructions for local inspector’s use.

•

IMPORTANT

–

Observe all

governing codes and ordinances.

• Note to Installer –Be sure to leave these

instructions with the Consumer.

• Note to Consumer –Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires basic mechanical skills.

• Completion time – 1 hour

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not covered under the Warranty.

If you have questions, call 1-800-GECARES

or visit our Website at:

www.GEAppliances.com

Installation

Disposer

Instructions

WHAT YOU WILL NEED

• Phillips and flat blade screwdrivers

• Channel lock pliers, slip joint • Hammer

• Nut driver

PREPARATION

1. Disconnect electrical power supply to disposer.

2. Remove old disposer or sink flange assembly.

3. Inspect drain line. If it is heavily coated with hardened

grease and accumulations, rout out with a plumber’s snake.

4. Remove old sealing materials and gasketing from sink opening, both top and bottom.

NOTE: Top and bottom of sink surfaces must be free of any materials to prevent leaks.

NOTE: Pay close attention to the order of the sink flange parts, as they have been correctly assembled by the factory.

A. Disassemble the sink flange assembly from the

disposer by turning the mount ring to the left (clockwise) and removing it.

B. Raise the mount ring toward the top of the sink

flange. Remove the cushion mount and the mount ring. You may want to practice installing the cushion mount at this point before you are under the sink.

C. Unscrew the support ring from the sink flange and

remove the fiber gasket. You are now left with the sink flange and the rubber gasket.

D. The rubber gasket is used instead of plumbers

putty with stainless steel sinks. Some cast sinks will require putty.

E. If no putty is used, insert the sink flange through the

rubber gasket into the sink opening. Do not turn the flange once it is seated.

F. If you use putty instead of the gasket, form a ring

around the underside of the sink flange. Insert the flange into the sink opening, press down hard to squeeze out excess putty. From under the sink, trim off excess putty flush with the bottom edge of the sink opening.

G.From underneath the sink,

slip the fiber gasket onto the exposed sink flange. With arrows pointing up, screw the support ring onto the sink flange and hand tighten until the sink flange will not move. At this point you may want to insert the stopper in the sink and fill with water to check the sink flange seal and insure there are no leaks.

H.Place the mount ring over

the sink flange and hold in place while installing the cushion mount (large side down). Make sure the groove on the inside of the cushion mount fits over the lip on the sink flange, similar to putting the lid on a plastic container. Run your fingers around the entire cushion mount with slight pressure. Do not press too hard. When the cushion mount is properly seated, the mount ring can be pulled downward over the cushion mount and will be free to turn.

Installation Instructions

COMPONENTS AND INSTALLATION

COMPONENTS

INSTALLATION OF SINK FLANGE

(Read completely before starting.)

Groove

Top

Bottom Bead

Sink Flange

Rubber Gasket

Sink

Fiber Gasket

Support Ring

Open Area No Obstruction

Sink Flange

Mount Ring should be free to move up and down

Cushion Mount Detail

*Stopper

*Removable Splash Guard

Sink Flange

Rubber Sink Flange Gasket

Groove

Dishwasher Discharge Inlet

Elbow Gasket

Hopper

Sink

Fiber Gasket

Support Ring (Note Arrows Indicating Up)

Screws

Discharge Elbow

Elbow Flange

Mount Ring

Rating Label in This Area

Tightening Ears

End Bell (Electrical Connections)

Cushion Mount

*Not used with batch feed model

Sink Flange Assembly

Disposer

Hand-tighten sink flange

Correctly Installed Sink Flange

Bottom Bead of Cushion Mount

Cushion Mount

Groove

Bottom Bead

(shown for proper orientation)

Installation Instructions

KNOCK OUT PLUG

Using a blunt instrument (steel punch or wooden dowel), knock out entire plug. Do not use a screwdriver or sharp instrument. When knockout plug falls into disposer, you may remove it or simply grind it up when the disposer is used. This will not damage the disposer in any way, but may take some time to grind, over the course of several uses.

DISHWASHER CONNECTION (IF REQUIRED)

If you are connecting to a dishwasher, complete the following step. If a dishwasher is not to be connected, go on to “Attaching the Discharge Elbow” section.

Connect the dishwasher hose using a hose clamp. If the hose size is different, you will need a stepped rubber adapter.

CONNECT HOSE

Knock out plug

CONNECT DISCHARGE ELBOW

Connect the discharge elbow to the disposer.* Make sure all plumbing connections are tight.

ATTACHING THE DISCHARGE ELBOW

Rubber Gasket

Hose Clamp

Stepped Rubber Adapter

Discharge Elbow

* Some installations (see page 8 for examples) may

require the use of a flexible drain pipe.

LOCK MOUNT RING

Turn the mount ring to the right until it locks up tight. Hopper projections must be to the extreme left of the mounting slots. If the mount ring is hard to turn, you may add a small amount of petroleum jelly or liquid soap to the hopper projection. Run water and check for leaks.

Installation Instructions

Hopper Projection in “Supported” Position

Hopper Projection in “Locked” Position

Mount Ring

Locking Detail

Check the unit for leaks 24 hours after installation and first operation.

CHECK FOR LEAKS

CONNECTING DISPOSER TO SINK FLANGE

Line up the disposer under the sink flange. Guide the hopper projections into the mount ring slots. Turn the mount ring about

1/4″ to the right so

that the disposer is temporarily supported.

Turn the mount ring and the disposer until the disposer discharge elbow lines up with the outlet pipe (see page 8).

LINE UP WITH OUTLET PIPE

Mount Ring Slot

Hopper Projection

Discharge Elbow

Outlet Pipe

ATTACH TO SINK FLANGE

SINGLE BOWL

DOUBLE BOWL

CENTER OUTLET**

DOUBLE BOWL END OUTLET**

*Approx.

GFC320F GFC325F

DIMENSIONS

63/16”

/16”

1211/16”

/2”

/8”

Direct replacement for most makes & models.

*9″ for model GFC320F,

GFC520F, GFC325F, & GFC525F.

*10″ for models GFC530F,

GFC535F, GFC720F & GFC1020F.

*12″ for models GFB760F

& GFB1060F.

GFC520F GFC525F

GFC530F GFC535F

GFC720F

GFC1020F

/2”

/16”

/4”

/2”

/16”

/4”

/2”

/16”

/2”

615/16”

/8”

/4”

/16”

/2”

41/2”

GFB760F

Batch Feed Operation

/2”

/8”

/2”

/16”

/8”

/2”

11/2”

/16”

/8”

/2”

/16”

/2”

GFB1060F

Batch Feed Operation

Installation Instructions

SOME TYPICAL INSTALLATIONS

63/16”

/16”

/2”

/8”

**Flexible drain pipe may be necessary for this application.

NOTE: It is essential for the proper operation of the disposer that this

dimension be 9″–12″, depending upon the

models listed above, to avoid standing water in disposer motor housing.

+ 16 hidden pages