GE GDT655SGJWW, GDT655SGJBB, GDF650SMJES, GDF650SGJWW, GDT655SMJES Installation Manual

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com.
In Canada, please call 1.800.561.3344 or visit www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

• 7RUHGXFHWKHULVNRIHOHFWULFVKRFN¿UHRULQMXU\WR
persons, the installer must ensure that the dishwasher is
completely enclosed at the time of installation.

• FOR PERSONAL SAFETY: Remove house fuse or open
circuit breaker before beginning installation. Do not use an
extension cord or adapter plug with this appliance.

• The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check with

DTXDOL¿HGHOHFWULFLDQRUVHUYLFHUHSUHVHQWDWLYHLI\RXDUH

in doubt that the appliance is properly grounded.

• If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.

CAUTION

Do not remove wood base until you are ready to install the
dishwasher. The dishwasher will tip over when the door is
opened if base is removed.

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS shown
throughout these instructions. While performing installations
described in this booklet, gloves, safety glasses or goggles
should be worn.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions for the

consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with your

Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.

• Completion Time – 1 to 3 Hours. New installations require
more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow for future removal from the enclosure if service is required.
Care should be exercised when the appliance is installed or removed,

to reduce the likelihood of damage to the power supply cord.
If you received a damaged dishwasher, you should immediately

contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for available

custom panel kits.
Your dishwasher is a water heating appliance.

Printed in the United States

CHECK THE FOLLOWING

 Tub trim does not interfere with the door
 Dishwasher is square and level at both the top and bottom

of the cabinet opening, with no twisting or distortion of the
tub or door

 $OOOHJVRIWKHGLVKZDVKHUDUH¿UPO\LQFRQWDFWZLWKWKH

ÀRRU

 Drain hose is not pinched between the dishwasher and

DGMDFHQWFDELQHWVRUZDOOV

 7XEWULPLVIXOO\VHDWHGRQWKHWXEÀDQJH

READ CAREFULLY

KEEP THESE INSTRUCTIONS

31-31560 02-16 GE

Installation Preparation

PARTS SUPPLIED
IN INSTALLATION PACKAGE:

• Junction box cover and #10 hex-head screw

• Hose clamp

• Drain hose (approximately 58" long)

• Drain hose hanger

• 2 #8-18 hex head screws to secure brackets to washer
tub frame

• 1 top trim piece (on some models)

• 2 side trim pieces

• 2 mounting brackets for wood countertops or side
cabinets

• 2 #8-18 x 5/8" Phillips special head screws, to secure
dishwasher to underside of countertop or to side

cabinets

• Literature, samples and/or coupons

MATERIALS YOU WILL NEED:

• 90° elbow (3/4"hose internal thread on one end,
opposite end sized to fit water supply)

• UL-listed wire nuts (3)

• Masking Tape

Materials Needed for New Installations:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5.4 Ft)
or WX09X70911 (7.9 ft) depending on your installation.

• Screw-type hose clamps

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Hot Water Line–3/8" minimum, copper tubing
(including ferrule, compression nut) or GE Part #

WX28X326, flexible braided hose.

• WD24X10065 drain hose (12' long), if needed

Junction

Box Cover

Mounting

Brackets

90°Elbow

Air Gap

Strain Relief

#10

Hex-Head

Junction

Box Screw

1/2" long

Top Trim Piece

(on some models)

#8 Phillips

Special

Head Screws

5/8" long

Waste Tee

Hand

6KXW2ȹ

Valve

Hose Clamp

Drain Hose Hanger

Plug Buttons

Wire Nuts (3)

Electrical Cable
(or Power Cord, if applicable)

Hot Water Line

Masking Tape

(if applicable)

Drain Hose

#8 Hex-Head Mounting

Bracket Screws

Side Trim Pieces

Literature

Coupler for

optional drain

hose

Hose Clamps

Optional
12' Drain Hose
WD24X10065

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4" and 5/16" nutdriver

• $GMXVWDEOHZUHQFK

• Level

• Carpenter's square

• Measuring tape

• Safety glasses

• Flashlight

• %XFNHWWRFDWFKZDWHUZKHQÀXVKLQJWKHOLQH

• 15/16" socket (optional for skid removal)

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

2

Phillips-Head
Screwdriver

15/16" Socket

Flashlight

Gloves

1/4" and 5/16"
Nutdriver

Pliers

6"
Adjustable
Wrench

Bucket

Level

Tubing Cutter

Safety Glasses

Hole Saw Set

Carpenter's
Square

Measuring Tape

Drill and Bits

Installation Preparation

PREPARE DISHWASHER ENCLOSURE

This Wall Area
must be Free
of Pipes or

33-1/2” to 34-3/4”

Underside of

Countertop

to Floor

+

34-1/2" 1/4"
Underside of

Countertop

to Floor

wires

Plumbing and Electric Service

Must Enter Inside This Area

24"
Min.

Figure A

• The rough cabinet opening must be at least 24" deep, 24"

wide and approximately 34-1/2" high from floor to underside
of the countertop.

24"
Min.

4"

Cabinets
Square

6"

and
Plumb

WARNING

7RUHGXFHWKHULVNRIHOHFWULFVKRFN¿UHRULQMXU\WRSHUVRQVWKH

installer must ensure that the dishwasher is completely enclosed at
the time of installation.

• The dishwasher must be installed so that drain hose is no
more than 12' in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and
back, and must not support any part of the enclosure.

CLEARANCES:

• When installed into a corner,
allow 2" min. clearance
between dishwasher and

DGMDFHQWFDELQHWZDOORURWKHU

appliances. Allow 25-1/2" min.
clearance from the front
of the dishwasher for door
opening. Figure B.

Countertop

Dishwasher

25-1/2"

Clearance for Door

Opening 2" Minimum

Figure B

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 12' distance to drain.

• Drain connection height is not to exceed 72" above bottom
of dishwasher.

NOTE: Air gap must be used if waste tee or disposer
connection is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following
questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1 MUST
be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.

IMPORTANT – When

connecting drain line to disposer,
check to be sure that drain plug has
been removed. DISHWASHER WILL
NOT DRAIN IF PLUG IS LEFT IN PLACE.

Remove

Drain

Plug

Figure C

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and ordi­nances. The air gap must be installed according to manufacturer’s
instructions.

Drain Hose Hanger

32"

Min.

18"

Min.

Figure D

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Drain Hose Hanger

32"

Min.

18"

Min.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed before
attaching dishwasher drain hose to the disposer.

3

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker
before beginning installation. Do not use an extension cord or
adapter plug with this appliance.

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz., and
connected to an individual properly grounded branch circuit,
protected by a 15- or 20-ampere circuit breaker or time-delay
fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• If the electrical supply does not meet the above requirements,
call a licensed electrician before proceeding.

Figure E

18"

6"

18"

Receptacle
Location
Area

6"

Alternate Receptacle
Location in Adjacent
Cabinet

1-1/2" Dia. Hole (Max.)

24"

from Wall

Ground

Black

3"

from

Cabinet

White

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and be
connected to the equipment-grounding terminal or lead on
the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipment­grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is installed and
grounded in accordance with all local codes and ordinances.

WARNING

The improper connection of the equipment grounding conductor

FDQUHVXOWLQDULVNRIHOHFWULFVKRFN&KHFNZLWKDTXDOL¿HG

electrician or service representative if you are in doubt that the
appliance is properly grounded.

For models equipped with power cord: Do not modify the plug
provided with the appliance; if it will not fit the outlet, have a
proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

• The wiring may enter the opening from either side, rear or the
floor within the shaded area illustrated above in Figure E and
defined in Figure A.

• Cut a 1-1/2" maximum diameter hole to admit the electrical
cable. Edges of hole should be smooth and rounded.
Permanent wiring connections may pass through the same
hole as the drain hose and hot water line, if convenient. If
cabinet wall is metal, the hole edge must be covered with a
bushing.
NOTE: Power cords with plug must pass through a separate
hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed as
shown in Figure E. Cable must extend a minimum of 24" from
the rear wall.

• For power cord connections, install a 3-prong grounding
type receptacle in the sink cabinet rear wall, 6" min. or 18"
maximum from the opening, 6" to 18" above the floor.

• Use only WX09X70910 or WX09X70911 Dishwasher Power
Cord Kit.

4

Installation Preparation

PREPARE HOT WATER LINE

NOTE: GE recommends copper tubing for the water line, but if
\RXFKRRVHWRXVHÀH[LEOHKRVHXVH*(·VWX28X326ÀH[LEOH

braided hose.

• The water supply line (3/8” copper tubing or flexible braided
hose) may enter from either side, rear or floor within the
shaded area shown in Figure F.

• The water supply line may pass through the same hole as the
electrical cable and drain hose. Or, cut an additional 1-1/2"
diameter hole to accommodate the water line. If power cord
with plug is used, water line must not pass through power
cord hole.

Hot

Cabinet

Shut-off
Valve

2"

From

1-1/2" Dia.

Hole

19" From Wall

4"

6"

CAUTION

Do not remove wood base until you are ready to install the
dishwasher. The dishwasher will tip over when the door is
opened if base is removed.

Cabinet Face

2" From Floor

Figure F

Water Line Connection

• If using a flexible braided supply hose, label the hose with the
installation date to use as reference. Flexible braided hoses,
elbows and gaskets should be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such
as under the sink. (Optional, but strongly recommended and
may be required by local codes.)

• Water connection is on the left side of the dishwasher. Install
the hot water inlet line, using no less than 3/8" copper tubing
or a flexible braided hose. Route the line as shown in Figure F
and extend forward at least 19" from rear wall.

$GMXVWZDWHUKHDWHUIRU)WR)WHPSHUDWXUH

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Turn page to begin dishwasher installation.

5

Dishwasher Installation

STEP 1: PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Mounting brackets

• Trim pieces (on some models)

• Drain hose hanger

• Owner's Manual

• Product samples and/or coupons

STEP 2: CHECK DOOR BALANCE

NOTE: If installing a Cus-

tom Door Panel (available
on some models), please
follow the instructions
found in the Custom Door
Panel kit WX35X20417.

• With dishwasher on
the wood base, check
the door balance by
opening and closing
the door.

• Door is properly
balanced if, when
opened, it self closes within 20° from vertical, stays in position
from 20° to 70° and falls fully open beyond 70°.

• If necessary increase or decrease tension as shown. Some
models will have 1 spring on each side and other models will
have 2 springs on one side and 1 spring on the other side.

/DWFKGRRUDQGDGMXVWVSULQJVWRFRUUHFWEDODQFH

Door
closes
within
20°

Door stays in
position from
20° to 70°

Door falls fully
open beyond 70°

Side View

Figure G

STEP 3: REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT – 'RQRWNLFNRȺZRRGEDVH

Damage will occur.

• Move the dishwasher close to the installation location and lay

it on its back. NOTE: Do not place the dishwasher on its side.

• Remove the 4 leveling legs on the underside of the wood base
with a 15/16" socket wrench.

• Discard base.

Approx.

1/2"

Figure I

• Screw leveling legs back into the dishwasher frame,
approximately 1/2" from frame as shown.

NOTE:6RPHPRGHOVKDYHUHDUDGMXVWDEOHOHYHOLQJZKHHOVDQG

will not require the 2 rear leveling legs.

STEP 4: REMOVE TOEKICK

• Remove the 2 toekick screws and toekick. Set aside for use in
Step 23.

Spring
hooked
to hole
inside rail

Side View

Increase

Tension

Decrease

Tension

NOTE: The number of
springs, on each side,
will vary by model.

Figure H

Make sure pully
cables are within
pulley shoulders

Custom

door

panel

Front View

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open easily or
falls too quickly, check spring cable routing. The cable is held in
place by “shoulders” on the pulley. Check to be sure cable has
not slipped over the pulley shoulders and is routed as shown.

6

Figure J

Toekick

Remove 2

Toekick Screws

Dishwasher Installation

STEP 5: IF NECESSARY, REMOVE FLOOR

PROTECT PAN (on some models)

• Disconnect leak sensor wire
(on some models).

• Pull floor protect pan forward and slide
it from under the dishwasher.

• Set aside for use in Step 21.

STEP 6: INSTALL 90° ELBOW

• Thread 90° elbow
onto the water valve.
Ensure rubber gasket
is located between
valve and elbow.

• Do not overtighten
elbow. Water valve
bracket could
bend or water valve
fitting could break.

• Position the end of
the elbow to face the
rear of the dishwasher.

Water Valve
Bracket

Figure M

Squeeze connector at top

to release snap feature

Leak Sensor

Floor Protect Pan

Figure L

Front of dishwasher

90° Elbow

Fill Hose

STEP 7: INSTALL DRAIN HOSE TO DRAIN

LOOP

Connect drain loop end to drain hose using the screw clamp
as shown in the figure.

Figure N

STEP 8: POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the floor of
the opening to avoid interference with base of dishwasher
and components under dishwasher.

4"

6"

Figure O

STEP 9:

4"

6"

Water

Line

House
Wiring

INSTALL DRAIN HOSE,
THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain
hose into the hole in cabinet side. If a power cord is used,
guide the end through a separate cabinet opening.

House
Wiring

Power Cord

(If used)

Drain

Water
Line

Ensure drain hose is not
twisted or pinched

Maximum drain hose
length is 15'

Do not disconnect or remove high
drain loop from left side of dishwasher

Figure P

Hose

7LS3UHYHQWXQQHFHVVDU\VHUYLFHFDOOFKDUJHVIRU¿OOGUDLQ

or noise concerns.

Position utility lines so they do not interfere with anything
under or behind the dishwasher.

Insulation

Blanket

NOTE: The high drain loop on the side of the tub is designed for
better wash performance. Do not remove from the side of the tub.

7

Dishwasher Installation

STEP 10: SLIDE DISHWASHER THREE-FOURTHS

OF THE WAY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

• Grasp the sides of the
front panel and slide
dishwasher into the
opening a few inches
at a time.

Do not push against
front door panel with
knee. Damage to the
door panel will occur.

• As you proceed, pull the drain hose through the opening under the
sink. Stop pushing when the dishwasher extends about 6 inches

IRUZDUGRIDGMDFHQWFDELQHWV

• Make sure drain hose is not kinked under or behind the dishwasher.

• Make certain the house wiring, drain line and water line do not
interfere with components under dishwasher.

STEP 11: INSTALL TRIM PIECES

In this step you will need the trim pieces set aside in Step 1.

Top Trim

Figure Q

STEP 12: INSTALL MOUNTING BRACKETS

You will need the mounting brackets and 2 #8 hex-head screws set
aside in Step 1.

You must install the mounting brackets onto the dishwasher tub
frame top or sides prior to sliding the dishwasher into place under
the countertop. This dishwasher is capable of a true-flush installation
at a 24” deep opening. The mounting brackets have several
available attachment positions to accommodate different cabinet

constructions.

Install mounting brackets on top if the underside of

countertop is wood or wood-like material that accepts screws:

IMPORTANT - After installing brackets and before

FORVLQJWKHGLVKZDVKHUGRRUDGMXVWWKHEUDFNHWVE\EHQGLQJ

them up as needed, so that they do not contact the top of the
dishwasher door and cause damage.

Top Mounting

#8 Bracket
Screw

Bracket

Side
Trim

Top View

Side
Trim

Side Trim

Top

View

• Select the top trim piece (See Figure R) and line up center to the top

ODWFK3UHVVWKHWULPSLHFHRQWRWKHWXEÀDQJHPRYLQJIURPRQHVLGH

to the other.

• Select the left trim piece (see Figure R).Align top edge with the top

WULPDQGSUHVVLWRQWRWKHOHIWVLGHRIWKHWXEÀDQJHPRYLQJIURPWKH
WRSWRWKHERWWRP5HSHDWIRUWKHULJKWVLGHWXEÀDQJHWULPSLHFH

(See Figure R for right side trim piece.)

8

Figure R

)XOO\VHDWWRWXEÀDQJH

Tub frame

Tub trim
Door

Handle

Dishwasher
tub frame

Bend and break here
after installing if
counter has a short
overhang.

Figure S

• If you are installing the dishwasher under a counter with a short

overhang, the countertop brackets may extend beyond the edge
of the counter. If this is the case, remove the excess length by
repeatedly bending the brackets at the front notch only until they
break.

Install mounting brackets on sides if the countertop is

granite or similar material that will not accept wood screws:

%UHDNRȺIURQWSRUWLRQRIWKHWDEZLWKSOLHUVDWWKHORFDWLRQVKRZQ

prior to attaching to dishwasher.

• Position the left-hand side bracket as shown. Repeat with the right
bracket.

Side Mounting

Tub trim

Care should be taken to
ensure mounting screws
do not damage cabinetry

Bend and break
here if necessary

Bracket

Figure T

Dishwasher
tub frame

#8 Bracket
screw as
supplied

Do not pinch
the latch
wires in
#8 bracket
screw

Dishwasher Installation

STEP 13: PUSH DISHWASHER INTO

FINAL POSITION

• Check the tub insulation blanket, if equipped, to be sure it is

smoothly wrapped around the tub. It should not be “bunched
up” and it must not interfere with the door springs. If the
insulation is “bunched up” or interfering with the springs,
straighten and recenter the blanket prior to sliding the
dishwasher into its final position.

• Slide the dishwasher into the final position by pushing on
the sides of the door panel. Do not push or pull the door
in a partially open or closed position when moving the
dishwasher. Do not use a knee or push on the center of the
panel. If you do, damage to the panel will likely result. Check
that the dishwasher is squarely positioned in the cabinet
opening at both the top and the bottom of the appliance prior
to mounting to the cabinet.

IMPORTANT – Before opening the dishwasher door,

be certain the edges of the dishwasher door panel are behind

WKHIDFHRIWKHDGMDFHQWFDELQHWDQGQRWXSDJDLQVWWKHFDELQHW

face. Refer to Figure U. If the dishwasher door is opened
when the edge of the door is against the face of the cabinet,
dishwasher door damage and cabinet damage will occur.

• Open and close the dishwasher door to be sure it operates

VPRRWKO\DQGGRHVQRWUXERQWKHDGMDFHQWFDELQHW

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

Figure U

Incorrect Alignment

will result in door damage

Door Catches
on Cabinet Frame

Tip: Prevent unnecessary service charges for panel damage
or wash performance.

Check dishwasher alignment prior to opening dishwasher door
to prevent panel damage.

Make sure utility lines are not trapped or crushed behind
dishwasher. Crushed lines will restrict water flow.

Check that tub trim does not
contact the door at all points

Top

View

Tub trim may be trimmed if

necessary to ensure proper door

operation

Tub frame

Tub trim

Door

Handle

Do not allow tub trim to get

trapped by or come into contact

with the door

Top

View

Tub trim
trapped

E\GRRU

9

Dishwasher Installation

STEP 14: LEVEL DISHWASHER

IMPORTANT –

Dishwasher must be level for
proper dish rack operation,
wash performance and door
operation. The dishwasher
must be leveled left to right
and front to back. This
ensures the dish racks will
not roll in or out on their own,

FLUFXODWLRQZDWHUZLOOÀRZWR

the pump inlet, and the door
will close without hitting the
side of the tub.

• Remove the lower dish rack
and place a level on the
door and lower rack track
as shown in Figure V.

• If your model has rear
wheels, the height of

WKHZKHHOVDUHDGMXVWHG

from the front of the
dishwasher along
with the 2 front legs
on the bottom of the
dishwasher. Begin the
leveling process with the
front legs by individually
turning the front 2 legs.

%\DGMXVWLQJWKHIURQW

legs first, access to the rear leveling bolts is maximized easing rear

ZKHHODGMXVWPHQW:KHQWKHIURQWOHJVDUHDGMXVWHGWRDKHLJKW

resulting in an appropriate gap to the upper cabinet, proceed to

DGMXVWWKHUHDUOHYHOLQJZKHHOVE\DGMXVWLQJWKHOHYHOLQJEROWVDV
LOOXVWUDWHGLQ)LJXUH:,QGLYLGXDOO\WXUQWKHEROWVWRDGMXVWWKH

rear wheels. Slowly rotate the 2 bolts counter clockwise to raise
the back of the dishwasher, and clockwise to lower it. Continue

WRDGMXVWWKHIHHWDQGZKHHOVXQWLOWKHGLVKZDVKHULVOHYHODV

illustrated in Figure W. Ensure all 4 legs/wheels are firmly in contact
with the floor.

If your model has

•

4 leveling feet,

DGMXVWWKHOHYHORI

the dishwasher by
individually turning the
4 legs on the bottom
of the dishwasher as
illustrated in Figure WW.

Figure V

$GMXVW

Figure W

Tip: Prevent unnecessary service charges. Verify dishwasher is leveled.

Pull the dish racks half way out. They should stay put. Open and

FORVHWKHGRRU7KHGRRUVKRXOG¿WLQWKHWXERSHQLQJZLWKRXW

hitting the side of the tub. If the racks roll on their own, or the door
hits the side of tub, relevel the dishwasher.

$GMXVW

• The dishwasher is properly leveled when the level indicator is
centered left to right and front to back. Also, the dishwasher door
should close without hitting the side of the tub.

• Replace the lower rack.

• Pull each rack out, about halfway. Check to be sure it does not

 UROOEDFNRUIRUZDUGRQWKHGRRU,IWKHUDFNPRYHVDGMXVW 

leveling legs.

10

Figure WW

Dishwasher Installation

STEP 15: POSITION DISHWASHER, SECURE
TO COUNTERTOP OR CABINET

In this step you will need the 2 Phillips special head screws
from the screws set aside in Step 1.

The dishwasher must be secured to the countertop or the
cabinet sides. When the underside of the countertop is wood,
use Method 1. Use Method 2 when the underside of the
countertop is made of a material, such as granite, that will not
accept wood screws.

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so the front

SDQHODQGFRQWUROSDQHOGRQRWFRQWDFWWKHDGMDFHQWFDELQHWV

or countertop. Mounting screws must be driven straight and
flush. Protruding screw heads could scratch the door panel or
control panel and interfere with door operation.

Method 1
Secure dishwasher to underside of wood countertop.

• Recheck alignment of the dishwasher in the cabinet. Refer to
Steps 13 and 14. Door panel and/or control panel must not
hit cabinets or countertop.

• Fasten the dishwasher to the underside of the countertop

ZLWKWKH3KLOOLSVVSHFLDOKHDGVFUHZV5HIHUWR¿JXUH
0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage.

• Install plug buttons to the side of the tub well in the holes
provided.

Brackets

Wood Countertop

Method 2
Secure dishwasher to cabinet sides.

• Recheck alignment of the dishwasher in the cabinet. Refer
to Steps 13 and 14. Door panel and/or control panel must
not hit cabinets or countertop.

)DVWHQWKHGLVKZDVKHUWRWKHDGMDFHQWFDELQHWVZLWKWKH

2 Phillips special head screws provided. Refer to Figure X.

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage. Do not screw into the cabinet face frame.

• Install plug buttons to the side of the tub well in the holes
provided.

Solid Surface Countertop

Granite Countertop

Side Brackets

Figure X

• Re-check that the dishwasher is squarely positioned in the
cabinet at both the top and bottom of the appliance after

PRXQWLQJWRWKHFDELQHWVFRXQWHUWRS$GMXVWLIQHFHVVDU\

• Confirm all leveling legs are in contact with the floor to
prevent the dishwasher from rocking and ensure proper door
and latch operation

STEP 16: CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

$WWDFKQXWWRHOERZXVLQJDQDGMXVWDEOHZUHQFK

If using a copper tubing connection:

• Slide compression nut, then ferrule over end of water line.

• Insert water line into 90° elbow.

• Slide ferrule against elbow and secure with compression nut.

IMPORTANT – Check to be sure that door spring

DQGRUGRRUVSULQJFDEOHGRQRWUXERUFRQWDFWWKH¿OOKRVHRU

water supply line.
Test by opening and
closing the door.
Reroute the water
supply lines if a
rubbing noise or
interference
occurs.

Figure Y

90° Elbow

Bottom Left Side

Hot Water
Supply Line

Compression
Nut

Ferrule

11

Dishwasher Installation

STEP 17: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"
diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose connector on the marked line, if required,

WR¿WWKHLQOHWSRUW

Cutting Line

1"

Figure Z

IMPORTANT: Do not cut corrugated

• If a longer drain hose is required and you did not purchase

drain hose WD24X10065, add up to 66" length for a total of
144" (12 feet) to the factory-installed hose. Use 5/8" or 7/8"
inside diameter hose and a coupler to connect
the 2 hose ends.
Secure the
connection
with hose
clamps.

Figure AA

NOTES:

• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED 72" ABOVE

BOTTOM OF DISHWASHER.

• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 12 FEET FOR

PROPER DRAIN OPERATION.

7^bT2[P\_

5/8"

portion of hose

2^d_[Ta

7^bT2[P\_

• Connect drain line to air gap, waste tee or disposer using the
previously determined method. Secure hose with a screw­type clamp.

Method 1 – Air gap with waste tee or disposer

Waste Tee Installation

Figure AB

Method 2 – “High drain loop” with waste tee or disposer

With this method you will need the drain hose hanger set aside
in Step 1.

Fasten drain hose to underside of countertop with the provided
hanger.

Drain Hose Hanger

32"

Min.

18"

Min.

Waste Tee Installation

Figure AC

Disposer Installation

18"

Min.

Disposer Installation

32"

Min.

IMPORTANT – When connecting drain line to

disposer, check to be sure that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.

Remove

Drain

Plug

Tip: Avoid unnecessary service call charges for a no drain
complaint.

Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose in the
dishwasher cavity from becoming kinked or crushed by the
dishwasher.

12

Dishwasher Installation

STEP 18: CONNECT POWER SUPPLY

If a power cord with plug is already installed proceed to
Step 19.

WARNING

If house wiring is not 2-wire with ground, a ground must be
provided by the installer. When house wiring is aluminum, be sure
to use UL-Listed anti-oxidant compound and aluminum-to-copper
connectors.

,QWKLVVWHS\RXZLOOQHHGWKHMXQFWLRQER[FRYHUDQGWKH
#10 Hex head screw from the screws set aside in Step 1.

6HFXUHKRXVHZLULQJWRWKHEDFNRIWKHMXQFWLRQER[ZLWKD

strain relief.

• Locate the 3 dishwasher wires, (white, black and green) with

WKHVWULSSHGHQGVFRPLQJRXWRIWKH$&MXPSHU8VH8/OLVWHG

wire nuts of appropriate size to connect incoming ground to
green, white to white and black to black.

,QVWDOOWKHMXQFWLRQER[FRYHUXVLQJKH[KHDGVFUHZ

Check to be sure that wires are not pinched under the cover.

0DNHVXUHWKDWWKHMXQFWLRQER[FRYHULVUHVWLQJRQWKH

mounting bracket.

• If using a Power Cord Kit, use GE part number WX09X70910
or WX09X70911 and refer to the included instructions.

NOTE: Do not remove the
Junction Box Bracket.

White

Ground
(Green)

AC
Jumper

STEP 19: PRETEST CHECKLIST

Review this list after installing your dishwasher to avoid
charges for a service call that is not covered by your
warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper packaging.

• Locate the Owner’s Manual set aside in Step 1.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not open and
close freely, check for proper routing of spring cable over

SXOOH\,IGRRUGURSVRUFORVHVZKHQUHOHDVHGDGMXVWVSULQJ

tension. See Step 2.

• Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 18.

• Check door alignment with tub. If door hits tub, level
dishwasher. See Step 14.

• Check door alignment with cabinet. If door hits cabinet,
reposition dishwasher. See Step 13.

• Check that door spring does not contact water line, fill hose,
wiring or other components. See Step 13.

• Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise.

• Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be between
120°F and 140°F. A minimum of 120°F temperature is
required for best wash performance. See “Prepare Hot Water
Line,” page 5.

Black

Figure AD

NOTE: All ground screws, brackets and wires must remain

intact.

Ground Screws

Junction Box
Bracket

• Add 1 quart of water to the bottom of the dishwasher to
lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten connections if
needed.

• Remove protective film if present from the control panel and
door.

• Check that tub trim does not contact the door.

13

Dishwasher Installation

STEP 20: DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,
if equipped.

• Select a cycle to run and push the Start button.

• Ensure the door is latched. Dishwasher should start.

• Check to be sure that water enters the dishwasher. If water
does not enter the dishwasher, check to be sure that water
and power are turned on.

• Check for leaks under the dishwasher. If a leak is found, turn
off power at the breaker, and then tighten water connections.
Restore power after leak is corrected.

• Check for leaks around the door. A leak around the door could
be caused by door rubbing or hitting against

DGMDFHQWFDELQHWV5HSRVLWLRQWKHGLVKZDVKHULIQHFHVVDU\

See Step 13.

• Press and hold the Start button for 3 seconds to cancel
the cycle. The unit will begin to drain. Check drain lines. If
leaks are found, turn off power at the breaker and correct
plumbing as necessary. Restore power after corrections are
made. See Steps 7, 8, 9, 10 and 17.

• Open dishwasher door and make sure all of the water has
drained. If not, check that disposer plug has been removed
and/or air gap is not plugged. Also check drain hose to be
sure it is not kinked underneath or behind dishwasher. See
Step 17.

• Press Start button once again and run dishwasher through
another cycle. Check for leaks and correct if required.

STEP 21:

REPLACE FLOOR PROTECT PAN
(on some models)

6OLGHWKHÀRRUSURWHFWSDQXQGHUWKHGLVKZDVKHUXQWLOLWVVLGH

lock slots are close to engaging the side mounting tabs on
the dishwasher.

Floor Protect Pan

Figure AE

• Lift the pan until its lock slots contact the mounting tabs and
push the pan back to engage them.

Mounting Tab

Two on each side

of the dishwasher

Lock Slots

Rear

Two on each side of

the floor protect pan

• Repeat this step as necessary.

Floor Protect Pan

Front

• When properly installed, the top of the lock slots will be over
the mounting tabs.

Mounting
Tab

Lock Slot

• Connect the leak sensor connector to the leak sensor
(on some models).

Leak Sensor

(on some models)

14

Dishwasher Installation

STEP 22: POSITION SOUND INSULATION

PIECE (on some models)

• Locate the sound insulation package inside the dishwasher.

• Stand the parts upright as shown.

Dishwasher
Door

Toekick

Figure AF

• Locate the control box.

Figure AG

• Push insulation block portion under the dishwasher until it is
beneath the control box.

• Push the panel portion up to the front of the block.

Insulation Block

(On some models.)

Control Box

Figure AH

STEP 23: REPLACE TOEKICK

• Place toekick against the legs of the dishwasher.

Toekick

Attachment

Figure AH

• Align the toekick with the bottom edge and make sure it is

DJDLQVWWKHÀRRU

• Insert and tighten the 2 toekick attachment screws. The

WRHNLFNVKRXOGVWD\LQFRQWDFWZLWKWKHÀRRU

Tip: Reduce sound from under the dishwasher. Make sure
toekick is against floor.

Screws

STEP 24: CHECK THE FOLLOWING

• Tub trim does not interfere with the door

• Dishwasher is square and level at both the top and bottom of
the cabinet opening, with no twisting or distortion of the tub
or door

$OOOHJVRIWKHGLVKZDVKHUDUH¿UPO\LQFRQWDFWZLWKWKHÀRRU

• Drain hose is not pinched between the dishwasher and

DGMDFHQWFDELQHWVRUZDOOV

7XEWULPLVIXOO\VHDWHGRQWKHWXEÀDQJH

(on some models)

Push the sides of the insulation behind

the toekick attachment screw holes

• Tuck the sides of the front panel behind the toekick
attachment screw holes.

• Open door all the way, if the door doesn’t stay fully open,

DGMXVWWKHLQVXODWLRQSDQHO

• Align the screw holes with the screw holes on the legs of the
dishwasher.

• Ensure vent opening is not blocked by insulation.

Vent opening

Location and appearance will vary

STEP 25: LITERATURE

• Be sure to leave complete literature package, these
Installation Instructions and product samples and/or coupons
with the consumer.

15