GE D30D00HCHF8AH6AM6BP8BX7A, D30 Instruction Manual

IISO 9001

G

N

E

I

L

M

I

U

T

L

T

E

S

I

R

G

E

E

D

R

837767A2.CDR

GE

LISTED

52TL

IND.CONT. EQ.

E83849

Digital Energy

D30 Line Distance Protection

System

UR Series Instruction Manual

D30 revision: 7.0x

Manual P/N: 1601-0116-Y4 (GEK-113664C)

GE Digital Energy
650 Markland Street
Markham, Ontario
Canada L6C 0M1
Tel: [phone] Fax: [phone]
Internet: http://www.GEDigitalEnergy.com

*1601-0116-Y4*

GE Multilin's Quality Management

System is registered to ISO

9001:2008

QMI # 005094

UL # A3775

Copyright © 2015 GE Multilin Inc. All rights reserved.
D30 Line Distance Protection System UR Series Instruction Manual revision 7.0x.
FlexLogic, FlexElement, FlexCurve, FlexAnalog, FlexInteger, FlexState, EnerVista,

CyberSentry, HardFiber, Digital Energy, Multilin, and GE Multilin are trademarks
or registered trademarks of GE Multilin Inc.

The contents of this manual are the property of GE Multilin Inc. This
documentation is furnished on license and may not be reproduced in whole or in
part without the permission of GE Multilin. The content of this manual is for
informational use only and is subject to change without notice.
Part number: 1601-0116-Y4 (August 2015)

TABLE OF CONTENTS

1. GETTING STARTED 1.1 IMPORTANT PROCEDURES

1.1.1 CAUTIONS AND WARNINGS ...........................................................................1-1

1.1.2 INSPECTION PROCEDURE ............................................................................. 1-2

1.2 UR OVERVIEW

1.2.1 INTRODUCTION TO THE UR ...........................................................................1-3

1.2.2 HARDWARE ARCHITECTURE......................................................................... 1-3

1.2.3 SOFTWARE ARCHITECTURE.......................................................................... 1-5

1.2.4 IMPORTANT CONCEPTS................................................................................. 1-5

1.3 ENERVISTA UR SETUP SOFTWARE

1.3.1 PC REQUIREMENTS ........................................................................................ 1-6

1.3.2 INSTALLATION.................................................................................................. 1-6

1.3.3 CONFIGURING THE D30 FOR SOFTWARE ACCESS.................................... 1-7

1.3.4 USING THE QUICK CONNECT FEATURE.....................................................1-10

1.3.5 CONNECTING TO THE D30 RELAY .............................................................. 1-15

1.4 UR HARDWARE

1.4.1 MOUNTING AND WIRING............................................................................... 1-17

1.4.2 COMMUNICATIONS........................................................................................ 1-17

1.4.3 FACEPLATE DISPLAY.................................................................................... 1-17

1.5 USING THE RELAY

1.5.1 FACEPLATE KEYPAD..................................................................................... 1-18

1.5.2 MENU NAVIGATION .......................................................................................1-18

1.5.3 MENU HIERARCHY ........................................................................................ 1-18

1.5.4 RELAY ACTIVATION....................................................................................... 1-18

1.5.5 RELAY PASSWORDS..................................................................................... 1-19

1.5.6 FLEXLOGIC CUSTOMIZATION ...................................................................... 1-19

1.5.7 COMMISSIONING ........................................................................................... 1-20

2. PRODUCT DESCRIPTION 2.1 INTRODUCTION

2.1.1 OVERVIEW........................................................................................................ 2-1

2.1.2 ORDERING........................................................................................................ 2-3

2.1.3 REPLACEMENT MODULES ............................................................................. 2-8

2.2 SPECIFICATIONS

2.2.1 PROTECTION ELEMENTS ............................................................................. 2-10

2.2.2 USER PROGRAMMABLE ELEMENTS........................................................... 2-14

2.2.3 MONITORING.................................................................................................. 2-15

2.2.4 METERING ......................................................................................................2-15

2.2.5 INPUTS............................................................................................................ 2-16

2.2.6 POWER SUPPLY ............................................................................................2-16

2.2.7 OUTPUTS........................................................................................................ 2-17

2.2.8 COMMUNICATION PROTOCOLS .................................................................. 2-18

2.2.9 INTER-RELAY COMMUNICATIONS............................................................... 2-19

2.2.10 ENVIRONMENTAL .......................................................................................... 2-19

2.2.11 TYPE TESTS ................................................................................................... 2-20

2.2.12 PRODUCTION TESTS .................................................................................... 2-20

2.2.13 APPROVALS ................................................................................................... 2-21

2.2.14 MAINTENANCE ............................................................................................... 2-21

3. HARDWARE 3.1 DESCRIPTION

3.1.1 PANEL CUTOUT ...............................................................................................3-1

3.1.2 REAR TERMINAL LAYOUT............................................................................... 3-7

3.2 WIRING

3.2.1 TYPICAL WIRING.............................................................................................. 3-8

3.2.2 DIELECTRIC STRENGTH................................................................................. 3-9

3.2.3 CONTROL POWER........................................................................................... 3-9

3.2.4 CT/VT MODULES............................................................................................ 3-10

3.2.5 PROCESS BUS MODULES ............................................................................ 3-11

3.2.6 CONTACT INPUTS AND OUTPUTS...............................................................3-12

3.2.7 TRANSDUCER INPUTS/OUTPUTS................................................................3-20

GE Multilin D30 Line Distance Protection System iii

TABLE OF CONTENTS

3.2.8 RS232 FACEPLATE PORT..............................................................................3-22

3.2.9 CPU COMMUNICATION PORTS.....................................................................3-22

3.2.10 IRIG-B...............................................................................................................3-25

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

3.3.1 DESCRIPTION .................................................................................................3-26

3.3.2 FIBER: LED AND ELED TRANSMITTERS ......................................................3-28

3.3.3 FIBER-LASER TRANSMITTERS .....................................................................3-28

3.3.4 G.703 INTERFACE...........................................................................................3-30

3.3.5 RS422 INTERFACE .........................................................................................3-33

3.3.6 RS422 AND FIBER INTERFACE .....................................................................3-35

3.3.7 G.703 AND FIBER INTERFACE ......................................................................3-35

3.3.8 IEEE C37.94 INTERFACE................................................................................3-36

3.3.9 C37.94SM INTERFACE ...................................................................................3-40

4. HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

4.1.1 INTRODUCTION ................................................................................................4-1

4.1.2 CREATING A SITE LIST ....................................................................................4-1

4.1.3 ENERVISTA UR SETUP OVERVIEW................................................................4-1

4.1.4 ENERVISTA UR SETUP MAIN WINDOW..........................................................4-3

4.2 EXTENDED ENERVISTA UR SETUP FEATURES

4.2.1 SETTINGS TEMPLATES ...................................................................................4-5

4.2.2 SECURING AND LOCKING FLEXLOGIC EQUATIONS....................................4-9

4.2.3 SETTINGS FILE TRACEABILITY.....................................................................4-11

4.3 FACEPLATE INTERFACE

4.3.1 FACEPLATE.....................................................................................................4-14

4.3.2 LED INDICATORS............................................................................................4-15

4.3.3 CUSTOM LABELING OF LEDS .......................................................................4-18

4.3.4 DISPLAY...........................................................................................................4-23

4.3.5 KEYPAD ...........................................................................................................4-23

4.3.6 BREAKER CONTROL ......................................................................................4-23

4.3.7 MENUS.............................................................................................................4-24

4.3.8 CHANGING SETTINGS ...................................................................................4-26

5. SETTINGS 5.1 OVERVIEW

5.1.1 SETTINGS MENU ..............................................................................................5-1

5.1.2 INTRODUCTION TO ELEMENTS......................................................................5-4

5.1.3 INTRODUCTION TO AC SOURCES..................................................................5-5

5.2 PRODUCT SETUP

5.2.1 SECURITY..........................................................................................................5-8

5.2.2 CYBERSENTRY SECURITY............................................................................5-12

5.2.3 DISPLAY PROPERTIES ..................................................................................5-19

5.2.4 CLEAR RELAY RECORDS..............................................................................5-21

5.2.5 COMMUNICATIONS ........................................................................................5-22

5.2.6 REAL TIME CLOCK .........................................................................................5-47

5.2.7 FAULT REPORTS............................................................................................5-52

5.2.8 OSCILLOGRAPHY...........................................................................................5-54

5.2.9 USER-PROGRAMMABLE LEDS .....................................................................5-56

5.2.10 USER-PROGRAMMABLE SELF TESTS .........................................................5-59

5.2.11 CONTROL PUSHBUTTONS ............................................................................5-60

5.2.12 USER-PROGRAMMABLE PUSHBUTTONS....................................................5-62

5.2.13 FLEX STATE PARAMETERS ..........................................................................5-68

5.2.14 USER-DEFINABLE DISPLAYS........................................................................5-68

5.2.15 DIRECT INPUTS/OUTPUTS ............................................................................5-71

5.2.16 TELEPROTECTION .........................................................................................5-78

5.2.17 INSTALLATION ................................................................................................5-79

5.3 REMOTE RESOURCES

5.3.1 REMOTE RESOURCES CONFIGURATION....................................................5-80

5.4 SYSTEM SETUP

5.4.1 AC INPUTS.......................................................................................................5-81

iv D30 Line Distance Protection System GE Multilin

TABLE OF CONTENTS

5.4.2 POWER SYSTEM............................................................................................ 5-82

5.4.3 SIGNAL SOURCES ......................................................................................... 5-83

5.4.4 BREAKERS...................................................................................................... 5-86

5.4.5 DISCONNECT SWITCHES ............................................................................. 5-90

5.4.6 FLEXCURVES ................................................................................................5-93

5.5 FLEXLOGIC

5.5.1 INTRODUCTION TO FLEXLOGIC ................................................................ 5-100

5.5.2 FLEXLOGIC RULES...................................................................................... 5-110

5.5.3 FLEXLOGIC EVALUATION ........................................................................... 5-110

5.5.4 FLEXLOGIC EXAMPLE ................................................................................. 5-111

5.5.5 FLEXLOGIC EQUATION EDITOR................................................................. 5-115

5.5.6 FLEXLOGIC TIMERS .................................................................................... 5-115

5.5.7 FLEXELEMENTS........................................................................................... 5-116

5.5.8 NON-VOLATILE LATCHES ........................................................................... 5-121

5.6 GROUPED ELEMENTS

5.6.1 OVERVIEW.................................................................................................... 5-122

5.6.2 SETTING GROUP ......................................................................................... 5-122

5.6.3 LINE PICKUP................................................................................................. 5-123

5.6.4 DISTANCE..................................................................................................... 5-125

5.6.5 POWER SWING DETECT............................................................................. 5-141

5.6.6 LOAD ENCROACHMENT.............................................................................. 5-149

5.6.7 PHASE CURRENT ........................................................................................ 5-151

5.6.8 NEUTRAL CURRENT.................................................................................... 5-161

5.6.9 GROUND CURRENT..................................................................................... 5-168

5.6.10 NEGATIVE SEQUENCE CURRENT ............................................................. 5-171

5.6.11 VOLTAGE ELEMENTS.................................................................................. 5-178

5.7 CONTROL ELEMENTS

5.7.1 OVERVIEW.................................................................................................... 5-186

5.7.2 TRIP BUS....................................................................................................... 5-186

5.7.3 SETTING GROUPS ....................................................................................... 5-188

5.7.4 SELECTOR SWITCH..................................................................................... 5-190

5.7.5 SYNCHROCHECK......................................................................................... 5-196

5.7.6 AUTORECLOSE............................................................................................ 5-200

5.7.7 DIGITAL ELEMENTS..................................................................................... 5-206

5.7.8 DIGITAL COUNTERS .................................................................................... 5-209

5.7.9 MONITORING ELEMENTS ........................................................................... 5-211

5.8 INPUTS AND OUTPUTS

5.8.1 CONTACT INPUTS........................................................................................ 5-221

5.8.2 VIRTUAL INPUTS.......................................................................................... 5-223

5.8.3 CONTACT OUTPUTS.................................................................................... 5-224

5.8.4 VIRTUAL OUTPUTS...................................................................................... 5-226

5.8.5 REMOTE DEVICES....................................................................................... 5-227

5.8.6 REMOTE INPUTS.......................................................................................... 5-228

5.8.7 REMOTE DOUBLE-POINT STATUS INPUTS .............................................. 5-229

5.8.8 REMOTE OUTPUTS...................................................................................... 5-229

5.8.9 RESETTING................................................................................................... 5-230

5.8.10 DIRECT INPUTS AND OUTPUTS................................................................. 5-231

5.8.11 TELEPROTECTION INPUTS AND OUTPUTS..............................................5-234

5.8.12 IEC 61850 GOOSE ANALOGS...................................................................... 5-236

5.8.13 IEC 61850 GOOSE INTEGERS..................................................................... 5-237

5.9 TRANSDUCER INPUTS AND OUTPUTS

5.9.1 DCMA INPUTS .............................................................................................. 5-238

5.9.2 RTD INPUTS.................................................................................................. 5-239

5.9.3 DCMA OUTPUTS .......................................................................................... 5-241

5.10 TESTING

5.10.1 TEST MODE .................................................................................................. 5-245

5.10.2 FORCE CONTACT INPUTS .......................................................................... 5-246

5.10.3 FORCE CONTACT OUTPUTS ...................................................................... 5-247

6. ACTUAL VALUES 6.1 OVERVIEW

6.1.1 ACTUAL VALUES MENU .................................................................................. 6-1

GE Multilin D30 Line Distance Protection System v

TABLE OF CONTENTS

6.2 STATUS

6.2.1 CONTACT INPUTS ............................................................................................6-3

6.2.2 VIRTUAL INPUTS ..............................................................................................6-3

6.2.3 REMOTE INPUTS ..............................................................................................6-3

6.2.4 REMOTE DOUBLE-POINT STATUS INPUTS...................................................6-4

6.2.5 TELEPROTECTION INPUTS.............................................................................6-4

6.2.6 CONTACT OUTPUTS ........................................................................................6-4

6.2.7 VIRTUAL OUTPUTS ..........................................................................................6-5

6.2.8 AUTORECLOSE.................................................................................................6-5

6.2.9 REMOTE DEVICES............................................................................................6-5

6.2.10 DIGITAL COUNTERS.........................................................................................6-6

6.2.11 SELECTOR SWITCHES ....................................................................................6-6

6.2.12 FLEX STATES....................................................................................................6-7

6.2.13 ETHERNET ........................................................................................................6-7

6.2.14 REAL TIME CLOCK SYNCHRONIZING ............................................................6-7

6.2.15 DIRECT INPUTS ................................................................................................6-8

6.2.16 DIRECT DEVICES STATUS ..............................................................................6-9

6.2.17 IEC 61850 GOOSE INTEGERS .........................................................................6-9

6.2.18 TELEPROTECTION CHANNEL TESTS.............................................................6-9

6.2.19 REMAINING CONNECTION STATUS.............................................................6-10

6.3 METERING

6.3.1 METERING CONVENTIONS ...........................................................................6-11

6.3.2 SOURCES ........................................................................................................6-14

6.3.3 SYNCHROCHECK ...........................................................................................6-17

6.3.4 TRACKING FREQUENCY................................................................................6-18

6.3.5 FLEXELEMENTS .............................................................................................6-19

6.3.6 IEC 61580 GOOSE ANALOG VALUES ...........................................................6-19

6.3.7 TRANSDUCER INPUTS/OUTPUTS.................................................................6-20

6.4 RECORDS

6.4.1 FAULT REPORTS............................................................................................6-21

6.4.2 EVENT RECORDS...........................................................................................6-21

6.4.3 OSCILLOGRAPHY...........................................................................................6-22

6.4.4 BREAKER MAINTENANCE .............................................................................6-22

6.5 PRODUCT INFORMATION

6.5.1 MODEL INFORMATION...................................................................................6-23

6.5.2 FIRMWARE REVISIONS..................................................................................6-23

7. COMMANDS AND
TARGETS

7.1 COMMANDS

7.1.1 COMMANDS MENU...........................................................................................7-1

7.1.2 VIRTUAL INPUTS ..............................................................................................7-1

7.1.3 CLEAR RECORDS.............................................................................................7-2

7.1.4 SET DATE AND TIME........................................................................................7-2

7.1.5 RELAY MAINTENANCE.....................................................................................7-3

7.1.6 SECURITY..........................................................................................................7-4

7.2 TARGETS

7.2.1 TARGETS MENU ...............................................................................................7-5

7.2.2 TARGET MESSAGES........................................................................................7-5

7.2.3 RELAY SELF-TESTS .........................................................................................7-5

8. SECURITY 8.1 USER ACCOUNTS

8.1.1 OVERVIEW ........................................................................................................8-1

8.1.2 ENABLING THE SECURITY MANAGEMENT SYSTEM....................................8-1

8.1.3 ADDING A NEW USER......................................................................................8-1

8.1.4 MODIFYING USER PRIVILEGES......................................................................8-2

8.1.5 PASSWORD REQUIREMENTS.........................................................................8-3

8.2 CYBERSENTRY

8.2.1 OVERVIEW ........................................................................................................8-4

8.2.2 SECURITY MENU ..............................................................................................8-6

vi D30 Line Distance Protection System GE Multilin

TABLE OF CONTENTS

9. THEORY OF OPERATION 9.1 DISTANCE ELEMENTS

9.1.1 INTRODUCTION................................................................................................ 9-1

9.1.2 PHASOR ESTIMATION..................................................................................... 9-1

9.1.3 DISTANCE CHARACTERISTICS...................................................................... 9-2

9.1.4 MEMORY POLARIZATION................................................................................ 9-6

9.1.5 DISTANCE ELEMENTS ANALYSIS..................................................................9-7

9.2 PHASE DISTANCE APPLIED TO POWER TRANSFORMERS

9.2.1 DESCRIPTION................................................................................................. 9-11

9.2.2 EXAMPLE ........................................................................................................ 9-14

9.3 GROUND DIRECTIONAL OVERCURRENT

9.3.1 DESCRIPTION................................................................................................. 9-16

9.3.2 EXAMPLE ........................................................................................................ 9-16

9.4 SERIES COMPENSATED LINES

9.4.1 DESCRIPTION................................................................................................. 9-18

9.5 FAULT LOCATOR

9.5.1 FAULT TYPE DETERMINATION..................................................................... 9-21

10. APPLICATION OF

SETTINGS

10.1 APPLICATION GUIDELINES

10.1.1 INTRODUCTION.............................................................................................. 10-1

10.1.2 IMPACT OF MEMORY POLARIZATION......................................................... 10-1

10.1.3 HIGH SET OVERCURRENT ELEMENTS.......................................................10-1

10.2 DISTANCE ELEMENTS (STEPPED DISTANCE SCHEME)

10.2.1 PHASE DISTANCE.......................................................................................... 10-2

10.2.2 GROUND DISTANCE ...................................................................................... 10-3

10.3 SERIES COMPENSATED LINES

10.3.1 INTRODUCTION.............................................................................................. 10-6

10.3.2 DISTANCE ....................................................................................................... 10-6

10.3.3 GROUND DIRECTIONAL OVERCURRENT ................................................... 10-7

10.3.4 HIGH-SET PHASE OVERCURRENT..............................................................10-7

10.4 PHASE DISTANCE THROUGH POWER TRANSFORMERS

10.4.1 PHASE DISTANCE PROTECTION ................................................................. 10-8

10.4.2 EXAMPLE ........................................................................................................10-9

11. MAINTENANCE 11.1 MODULES

11.1.1 REPLACE A MODULE..................................................................................... 11-1

11.2 BATTERIES

11.2.1 REPLACE BATTERY....................................................................................... 11-3

11.2.2 DISPOSE OF BATTERY.................................................................................. 11-4

11.3 UNINSTALL AND CLEAR FILES AND DATA

11.3.1 UNINSTALL AND CLEAR FILES AND DATA.................................................. 11-7

11.4 REPAIRS

11.4.1 REPAIRS ......................................................................................................... 11-8

11.5 STORAGE

11.5.1 STORAGE........................................................................................................ 11-9

11.6 DISPOSAL

11.6.1 DISPOSAL ..................................................................................................... 11-10

A. FLEXANALOG AND

FLEXINTEGER
PARAMETERS

GE Multilin D30 Line Distance Protection System vii

A.1 PARAMETER LISTS

A.1.1 FLEXANALOG ITEMS .......................................................................................A-1

A.1.2 FLEXINTEGER ITEMS .................................................................................... A-10

TABLE OF CONTENTS

B. MODBUS

COMMUNICATIONS

C. IEC 61850

COMMUNICATIONS

B.1 MODBUS RTU PROTOCOL

B.1.1 INTRODUCTION ............................................................................................... B-1

B.1.2 PHYSICAL LAYER ............................................................................................ B-1

B.1.3 DATA LINK LAYER ...........................................................................................B-1

B.1.4 MODBUS RTU CRC-16 ALGORITHM .............................................................. B-2

B.2 MODBUS FUNCTION CODES

B.2.1 SUPPORTED FUNCTION CODES ...................................................................B-4

B.2.2 READ ACTUAL VALUES OR SETTINGS (FUNCTION CODE 03/04H) ...........B-4

B.2.3 EXECUTE OPERATION (FUNCTION CODE 05H)........................................... B-5

B.2.4 STORE SINGLE SETTING (FUNCTION CODE 06H).......................................B-5

B.2.5 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H)................................ B-6

B.2.6 EXCEPTION RESPONSES............................................................................... B-6

B.3 FILE TRANSFERS

B.3.1 OBTAINING RELAY FILES VIA MODBUS........................................................ B-7

B.4 MEMORY MAPPING

B.4.1 MODBUS MEMORY MAP ................................................................................. B-9

B.4.2 DATA FORMATS............................................................................................. B-67

C.1 OVERVIEW

C.1.1 INTRODUCTION ............................................................................................... C-1

C.1.2 COMMUNICATION PROFILES......................................................................... C-1

C.1.3 FILE TRANSFER BY IEC 61850.......................................................................C-2

C.2 SERVER DATA ORGANIZATION

C.2.1 OVERVIEW ....................................................................................................... C-3

C.2.2 GGIO1: DIGITAL STATUS VALUES.................................................................C-3

C.2.3 GGIO2: DIGITAL CONTROL VALUES..............................................................C-3

C.2.4 GGIO3: DIGITAL STATUS AND ANALOG VALUES FROM RECEIVED

GOOSE DATA ................................................................................................... C-3

C.2.5 GGIO4: GENERIC ANALOG MEASURED VALUES.........................................C-3

C.2.6 MMXU: ANALOG MEASURED VALUES .......................................................... C-4

C.2.7 PROTECTION AND OTHER LOGICAL NODES............................................... C-4

C.3 SERVER FEATURES AND CONFIGURATION

C.3.1 BUFFERED/UNBUFFERED REPORTING........................................................C-6

C.3.2 FILE TRANSFER...............................................................................................C-6

C.3.3 TIMESTAMPS AND SCANNING....................................................................... C-6

C.3.4 LOGICAL DEVICE NAME ................................................................................. C-6

C.3.5 LOCATION ........................................................................................................ C-6

C.3.6 LOGICAL NODE NAME PREFIXES.................................................................. C-7

C.3.7 CONNECTION TIMING.....................................................................................C-7

C.3.8 NON-IEC 61850 DATA...................................................................................... C-7

C.3.9 COMMUNICATION SOFTWARE UTILITIES.....................................................C-7

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE

C.4.1 OVERVIEW ....................................................................................................... C-8

C.4.2 GSSE CONFIGURATION..................................................................................C-8

C.4.3 FIXED GOOSE..................................................................................................C-8

C.4.4 CONFIGURABLE GOOSE ................................................................................ C-8

C.4.5 ETHERNET MAC ADDRESS FOR GSSE/GOOSE ........................................ C-11

C.4.6 GSSE ID AND GOOSE ID SETTINGS............................................................C-11

C.5 IEC 61850 IMPLEMENTATION VIA ENERVISTA UR SETUP

C.5.1 OVERVIEW ..................................................................................................... C-12

C.5.2 CONFIGURING IEC 61850 SETTINGS .......................................................... C-13

C.5.3 ABOUT ICD FILES .......................................................................................... C-14

C.5.4 CREATING AN ICD FILE WITH ENERVISTA UR SETUP..............................C-18

C.5.5 ABOUT SCD FILES......................................................................................... C-18

C.5.6 IMPORTING AN SCD FILE WITH ENERVISTA UR SETUP........................... C-21

C.6 ACSI CONFORMANCE

C.6.1 ACSI BASIC CONFORMANCE STATEMENT ................................................C-23

C.6.2 ACSI MODELS CONFORMANCE STATEMENT............................................C-23

C.6.3 ACSI SERVICES CONFORMANCE STATEMENT .........................................C-24

viii D30 Line Distance Protection System GE Multilin

TABLE OF CONTENTS

C.7 LOGICAL NODES

C.7.1 LOGICAL NODES TABLE ...............................................................................C-27

D. IEC 60870-5-104

COMMUNICATIONS

D.1 IEC 60870-5-104 PROTOCOL

D.1.1 INTEROPERABILITY.........................................................................................D-1

D.1.2 POINT LIST........................................................................................................D-9

E. DNP COMMUNICATIONS E.1 DEVICE PROFILE DOCUMENT

E.1.1 DNP V3.00 DEVICE PROFILE ..........................................................................E-1

E.1.2 IMPLEMENTATION TABLE............................................................................... E-4

E.2 DNP POINT LISTS

E.2.1 BINARY INPUT POINTS....................................................................................E-8

E.2.2 BINARY AND CONTROL RELAY OUTPUT......................................................E-9

E.2.3 COUNTERS.....................................................................................................E-10

E.2.4 ANALOG INPUTS............................................................................................E-11

F. MISCELLANEOUS F.1 CHANGE NOTES

F.1.1 REVISION HISTORY ......................................................................................... F-1

F.1.2 CHANGES TO THE MANUAL ...........................................................................F-2

F.2 ABBREVIATIONS

F.2.1 STANDARD ABBREVIATIONS ......................................................................... F-5

F.3 WARRANTY

F.3.1 GE MULTILIN WARRANTY ............................................................................... F-7

GE Multilin D30 Line Distance Protection System ix

TABLE OF CONTENTS

x D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.1 IMPORTANT PROCEDURES

DANGER

WARNING

CAUTION

NOTICE

DANGER

CAUTION

1 GETTING STARTED 1.1IMPORTANT PROCEDURES

Read this chapter to help guide you through the initial setup of your new D30 Line Distance Protection System.

1.1.1 CAUTIONS AND WARNINGS

Before attempting to install or use the device, review all safety indicators in this document to help prevent injury, equipment
damage, or downtime.

The following safety and equipment symbols are used in this document.

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.

Indicates practices not related to personal injury.

a) GENERAL CAUTIONS AND WARNINGS

The following general safety precautions and warnings apply.

Ensure that all connections to the product are correct so as to avoid accidental risk of shock
and/or fire, for example such as can arise from high voltage connected to low voltage termi­nals.

Follow the requirements of this manual, including adequate wiring size and type, terminal torque settings, voltage,
current magnitudes applied, and adequate isolation/clearance in external wiring from high to low voltage circuits.

Use the device only for its intended purpose and application.

Ensure that all ground paths are uncompromised for safety purposes during device operation and service.

Ensure that the control power applied to the device, the AC current, and voltage input match the ratings specified
on the relay nameplate. Do not apply current or voltage in excess of the specified limits.

Only qualified personnel are to operate the device. Such personnel must be thoroughly familiar with all safety cau­tions and warnings in this manual and with applicable country, regional, utility, and plant safety regulations.

Hazardous voltages can exist in the power supply and at the device connection to current transformers, voltage
transformers, control, and test circuit terminals. Make sure all sources of such voltages are isolated prior to
attempting work on the device.

Hazardous voltages can exist when opening the secondary circuits of live current transformers. Make sure that
current transformer secondary circuits are shorted out before making or removing any connection to the current
transformer (CT) input terminals of the device.

For tests with secondary test equipment, ensure that no other sources of voltages or currents are connected to
such equipment and that trip and close commands to the circuit breakers or other switching apparatus are iso­lated, unless this is required by the test procedure and is specified by appropriate utility/plant procedure.

When the device is used to control primary equipment, such as circuit breakers, isolators, and other switching
apparatus, all control circuits from the device to the primary equipment must be isolated while personnel are
working on or around this primary equipment to prevent any inadvertent command from this device.

Use an external disconnect to isolate the mains voltage supply.

LED transmitters are classified as IEC 60825-1 Accessible Emission Limit (AEL) Class 1M.
Class 1M devices are considered safe to the unaided eye. Do not view directly with optical
instruments.

This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial
environments. Not to be used near electronic devices rated for Class B levels.

1

GE Multilin D30 Line Distance Protection System 1-1

1.1 IMPORTANT PROCEDURES 1 GETTING STARTED

837805A3.CDR

®

®

Model:
Mods:
Wiring Diagram:
Inst. Manual:
Serial Number:
Firmware:
Mfg. Date:
PO Num:
Item Num:

D30D00HCHF8AH6AM6BP8BX7A
000
See manual
1601-0116
MAZB98000029
D
NOV 26, 2012

600001234.56

Control Power:
Contact Inputs:
Contact Outputs:

88-300V DC @ 35W / 77-265V AC @ 35VA
300V DC Max 10mA
Refer to Instruction Manual

RATINGS:

D30

- M A A B 9 7 0 0 0 0 9 9 -

Line Distance Relay

GE Multilin

- M A A B 9 7 0 0 0 0 9 9 -

LISTED

52TL

IND.CONT. EQ.

E83849

NOTE

1.1.2 INSPECTION PROCEDURE

1

1. Open the relay packaging and inspect the unit for physical damage.

2. View the rear nameplate and verify that the correct model has been ordered and delivered.

Figure 1–1: REAR NAMEPLATE (EXAMPLE)

3. Ensure that the following items are included:

• Instruction manual (if ordered)

• GE EnerVista™ CD (includes the EnerVista UR Setup software and manuals in PDF format)

• Mounting screws

For product information, instruction manual updates, and the latest software updates, visit the GE Digital Energy website at

http://www.gedigitalenergy.com

.

If there is any noticeable physical damage, or any of the contents listed are missing, please contact GE Digital
Energy immediately.

GE DIGITAL ENERGY CONTACT INFORMATION AND CALL CENTER FOR PRODUCT SUPPORT:

GE Digital Energy
650 Markland Street
Markham, Ontario
Canada L6C 0M1

TELEPHONE: Worldwide [phone]

Europe/Middle East/Africa [phone]
North America toll-free 1 800 547 8629

FAX: [phone]
E-MAIL: Worldwide [e-mail]

Europe [e-mail]

HOME PAGE: http://www.gedigitalenergy.com/multilin

1-2 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.2 UR OVERVIEW

827822A3.CDR

Input elements

LAN

Programming

device

Operator
interface

Contact inputs Contact outputs

Virtual inputs

Virtual outputs

Analog inputs

Analog outputs

CT inputs

VT inputs

Input

status

table

Output

status

table

Pickup
Dropout
Operate

Protective elements

Logic Gates

Remote outputs

- IEC 61850

CPU module

Output elements

Remote inputs

Direct inputs Direct outputs

1.2UR OVERVIEW 1.2.1 INTRODUCTION TO THE UR

Historically, substation protection, control, and metering functions were performed with electromechanical equipment. This
equipment was gradually replaced by analog equipment, most of which emulated the single-function approach of their elec­tromechanical precursors. Both technologies required expensive cabling and auxiliary equipment to produce functioning
systems.

Recently, digital electronic equipment has begun to provide protection, control, and metering functions. Initially, this equip­ment was either single function or had very limited multifunction capability, and it did not significantly reduce the cabling and
auxiliary equipment required. However, recent digital relays are multifunctional, reducing cabling and auxiliaries signifi­cantly. These devices also transfer data to central control facilities and software using electronic communications. The
functions performed have become so broad that many users now prefer the term Intelligent Electronic Device (IED).

It is obvious to station designers that the amount of cabling and auxiliary equipment installed can be even further reduced,
to 20% to 70% of levels common in 1990, and achieve large cost reductions. This requires placing even more functions
within the IEDs.

Users of power equipment are also interested in reducing cost by improving power quality and personnel productivity, and
in increasing system reliability and efficiency. These objectives are realized through software that is used to perform func­tions at both the station and supervisory levels. The use of these systems is growing rapidly.

High-speed communication is required to meet the data transfer rates required by modern automatic control and monitoring
systems. Very high speed communications are required to perform protection signaling with a performance target response
time for a command signal between two IEDs, from transmission to reception, of less than 3 milliseconds. This has been
established by the IEC 61850 standard.

IEDs with such capabilities also provide significantly more power system data than was available, enhanced operations and
maintenance, and permit the use of adaptive system configuration for protection and control systems. This new generation
of equipment is easily incorporated into automation systems, at both the station and enterprise levels. The GE Multilin Uni­versal Relay (UR) series meets these goals.

1

a) UR BASIC DESIGN

The UR is a digital-based device containing a central processing unit (CPU) that handles multiple types of input and output
signals. The UR device can communicate over a local area network (LAN) with an operator interface, a programming
device, or another UR device.

The CPU module contains firmware that provides protection elements in the form of logic algorithms, as well as program­mable logic gates, timers, and latches for control features.

Figure 1–2: UR CONCEPT BLOCK DIAGRAM

1.2.2 HARDWARE ARCHITECTURE

GE Multilin D30 Line Distance Protection System 1-3

1.2 UR OVERVIEW 1 GETTING STARTED

827823A3.CDR

Pickup (PKP)
Dropout (DPO)
Operate (OP)

Protective elements

Protection elements
serviced by sub-scan

Read inputs

Solve logic

Set outputs

Input elements accept a variety of analog or digital signals from the field. The UR isolates and converts these signals into
logic signals used by the relay.

1

Output elements convert and isolate the logic signals generated by the relay into digital or analog signals that can be used

to control field devices.

b) UR SIGNAL TYPES

The contact inputs and outputs are digital signals associated with connections to hard-wired contacts. Both ‘wet’ and ‘dry’
contacts are supported.

The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include
signals generated by the local user interface. The virtual outputs are outputs of FlexLogic™ equations used to customize
the device. Virtual outputs can also serve as virtual inputs to FlexLogic equations.

The analog inputs and outputs are signals that are associated with transducers, such as Resistance Temperature Detec-
tors (RTDs).

The CT and VT inputs refer to analog current transformer and voltage transformer signals used to monitor AC power lines.
The UR-series relays support 1 A and 5 A CTs.

The remote inputs and outputs provide a means of sharing digital point state information between remote UR-series
devices. The remote outputs interface to the remote inputs of other UR-series devices. Remote outputs are FlexLogic oper­ands inserted into IEC 61850 GSSE and GOOSE messages.

The direct inputs and outputs provide a means of sharing digital point states between a number of UR-series IEDs over a
dedicated fiber (single or multimode), RS422, or G.703 interface. No switching equipment is required as the IEDs are con­nected directly in a ring or redundant (dual) ring configuration. This feature is optimized for speed and intended for pilot­aided schemes, distributed logic applications, or the extension of the input/output capabilities of a single relay chassis.

c) UR SCAN OPERATION

The UR-series devices operate in a cyclic scan fashion. The device reads the inputs into an input status table, solves the
logic program (FlexLogic equation), and then sets each output to the appropriate state in an output status table. Any result­ing task execution is priority interrupt-driven.

Figure 1–3: UR-SERIES SCAN OPERATION

1-4 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.2 UR OVERVIEW

1.2.3 SOFTWARE ARCHITECTURE

The firmware (software embedded in the relay) is designed in functional modules that can be installed in any relay as
required. This is achieved with object-oriented design and programming (OOD/OOP) techniques.

Object-oriented techniques involve the use of objects and classes. An object is defined as “a logical entity that contains
both data and code that manipulates that data”. A class is the generalized form of similar objects. By using this concept,
one can create a protection class with the protection elements as objects of the class, such as time overcurrent, instanta­neous overcurrent, current differential, undervoltage, overvoltage, underfrequency, and distance. These objects represent
completely self-contained software modules. The same object-class concept can be used for metering, input/output control,
software interface, communications, or any functional entity in the system.

Employing OOD/OOP in the software architecture of the D30 achieves the same features as the hardware architecture:
modularity, scalability, and flexibility. The application software for any UR-series device (for example, feeder protection,
transformer protection, distance protection) is constructed by combining objects from the various functional classes. This
results in a common interface across the UR series.

1.2.4 IMPORTANT CONCEPTS

As described above, the architecture of the UR-series relays differ from previous devices. To achieve a general understand­ing of this device, some sections of Chapter 5 are quite helpful. The most important functions of the relay are contained in
“elements”. A description of the UR-series elements can be found in the Introduction to elements section in chapter 5.
Examples of simple elements, and some of the organization of this manual, can be found in the Control elements section of
chapter 5. An explanation of the use of inputs from CTs and VTs is in the Introduction to AC sources section in chapter 5. A
description of how digital signals are used and routed within the relay is contained in the Introduction to FlexLogic section in
chapter 5.

1

GE Multilin D30 Line Distance Protection System 1-5

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

1.3ENERVISTA UR SETUP SOFTWARE 1.3.1 PC REQUIREMENTS

1

The faceplate keypad and display or the EnerVista UR Setup software can be used to communicate with the relay. The
EnerVista UR Setup software interface is the preferred method to edit settings and view actual values because the com­puter monitor can display more information.

The following minimum requirements must be met for the EnerVista UR Setup software to properly operate on a computer:

• Pentium class or higher processor (Pentium II 300 MHz or higher recommended)

• Windows 95, 98, 98SE, ME, NT 4.0 (Service Pack 4 or higher), 2000, XP

• Internet Explorer 4.0 or higher

• 128 MB of RAM (256 MB recommended)

• 200 MB of available space on system drive and 200 MB of available space on installation drive

• Video capable of displaying 800 x 600 or higher in high-color mode (16-bit color)

•Serial port

• Ethernet port of the same type as one of the UR CPU ports or a LAN connection to the UR

• Internet access or a DVD drive
The following qualified modems have been tested to be compliant with the D30 and the EnerVista UR Setup software:

• US Robotics external 56K FaxModem 5686

• US Robotics external Sportster 56K X2

• PCTEL 2304WT V.92 MDC internal modem

1.3.2 INSTALLATION

After ensuring the minimum requirements for using EnerVista UR Setup are met (previous section), install the EnerVista UR
Setup from the GE EnerVista CD. Or download the UR EnerVista software from http://www.gedigitalenergy.com/multilin
and install it.

If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first
in EnerVista under Maintenance > Update Firmware.

1. Insert the GE EnerVista CD into your CD-ROM drive.

2. Click the Install Now button and follow the installation instructions to install the EnerVista software.

3. When installation is complete, start the EnerVista Launchpad application.

4. Click the IED Setup section of the Launch Pad window.

5. In the EnerVista Launch Pad window, click the Add Product button and select the appropriate product, shown as fol­lows. Select the "Web" option to ensure the most recent software release, or select "CD" if you do not have a web con-

1-6 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

nection, then click the Add Now button to list software items for the product. EnerVista Launchpad then obtains the
software from the Internet or CD and automatically starts the installation program.

6. Select the complete path, including the new directory name, where the EnerVista UR Setup is to be installed.

7. Click on Next to begin the installation. The files are installed in the directory indicated, and the installation program

automatically creates icons and adds EnerVista UR Setup to the Windows start menu.

8. Click Finish to complete the installation. The UR-series device is added to the list of installed IEDs in the EnerVista

Launchpad window, as shown.

1

1.3.3 CONFIGURING THE D30 FOR SOFTWARE ACCESS

a) OVERVIEW

The user can connect remotely to the D30 through the rear RS485 port or the rear Ethernet port with a computer running
the EnerVista UR Setup software. The D30 can also be accessed locally with a computer through the front panel RS232
port or the rear Ethernet port using the Quick Connect feature.

• To configure the D30 for remote access via the rear RS485 port, see the Configuring Serial Communications section.

GE Multilin D30 Line Distance Protection System 1-7

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

• To configure the D30 for remote access via the rear Ethernet port, see the Configuring Ethernet Communications sec-

1

tion.

• To configure the D30 for local access with a computer through either the front RS232 port or rear Ethernet port, see the
Using the Quick Connect Feature section.

b) CONFIGURING SERIAL COMMUNICATIONS

Before starting, verify that the serial cable is properly connected to the RS485 terminal on the back of the device. The face­plate RS232 port is intended for local use and is not described in this section; see the Using the Quick Connect Feature
section.

A computer with an RS232 port and a serial cable is required. To use the RS485 port at the back of the relay, a GE Multilin
F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.

1. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or
online from http://www.gedigitalenergy.com/multilin

2. Connect the computer to the F485 and the F485 to the RS485 terminal on the back of the UR device, or connect
directly the computer to the RS232 port on the front of the relay.

3. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

4. Click the Device Setup button to open the Device Setup window and click the Add Site button to define a new site.

5. Enter a site name in the “Site Name” field. Optionally add a short description of the site along with the display order of
devices defined for the site. In this example, we use “Location 1” as the site name. Click the OK button when complete.
The new site appears in the upper-left list in the EnerVista UR Setup window.

6. Click the Device Setup button, then select the new site to re-open the Device Setup window.

7. Click the Add Device button to define the new device.

8. Enter a name in the "Device Name” field and a description (optional) of the site.

9. Select “Serial” from the Interface drop-down list. This displays a number of interface parameters that must be entered
for serial communications.

). See the Software Installation section if not already installed.

Figure 1–4: CONFIGURING SERIAL COMMUNICATIONS

10. Enter the COM port used by the computer, the baud rate, and parity settings from the front panel

SETUP

 COMMUNICATIONS  SERIAL PORTS menu, and the relay slave address setting from the front panel SETTINGS

1-8 D30 Line Distance Protection System GE Multilin

SETTINGS  PRODUCT

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

 PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL  MODBUS SLAVE ADDRESS menu in their respective

fields.

11. Click the Read Order Code button to connect to the D30 device and upload the order code. If a communications error

occurs, ensure that the EnerVista UR Setup serial communications values entered in the previous step correspond to
the relay setting values.

12. Click the OK button when the relay order code has been received. The new device is added to the Site List window (or

Online window) located in the top left corner of the main EnerVista UR Setup window.

The device has now been configured for RS232 communications. Proceed to the Connecting to the D30 section to begin
communication.

c) CONFIGURING ETHERNET COMMUNICATIONS

Before starting, verify that the Ethernet network cable is properly connected to the Ethernet port on the back of the relay. To
setup the relay for Ethernet communications, you define a Site, then add the relay as a Device at that site.The computer
and UR device must be on the same subnet.

1. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or

online from http://www.gedigitalenergy.com/multilin

2. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

3. Click the Device Setup button to open the Device Setup window, then click the Add Site button to define a new site.

4. Enter the desired site name in the “Site Name” field. If desired, a short description of site can also be entered along

with the display order of devices defined for the site. In this example, we use “Location 2” as the site name. Click the
OK button when complete.

5. The new site appears in the upper-left list in the EnerVista UR Setup window. Click the Device Setup button then

select the new site to re-open the Device Setup window.

6. Click the Add Device button to define the new device.

7. Enter the desired name in the “Device Name” field and a description (optional) of the site.

8. Select “Ethernet” from the Interface drop-down list. This displays a number of interface parameters that must be

entered for proper Ethernet functionality.

). See the Software Installation section for installation details.

1

Figure 1–5: CONFIGURING ETHERNET COMMUNICATIONS

GE Multilin D30 Line Distance Protection System 1-9

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

9. Enter the relay IP address specified in the front panel SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NET-

1

WORK  IP ADDRESS in the “IP Address” field.

10. Enter the relay slave address and Modbus port address values from the respective settings in the front panel SETTINGS

 PRODUCT SETUP  COMMUNICATIONS  MODBUS PROTOCOL menu.

11. Click the Read Order Code button to connect to the D30 device and upload the order code. If an communications
error occurs, ensure that the three EnerVista UR Setup values entered in the previous steps correspond to the relay
setting values.

12. Click OK when the relay order code has been received. The new device is added to the Site List window (or Online
window) located in the top left corner of the main EnerVista UR Setup window.

The Site Device has now been configured for Ethernet communications. Proceed to the Connecting to the D30 section to
begin communications.

1.3.4 USING THE QUICK CONNECT FEATURE

a) USING QUICK CONNECT VIA THE FRONT PANEL RS232 PORT

Before starting, verify that the serial cable is properly connected from the computer to the front panel RS232 port with a
straight-through 9-pin to 9-pin RS232 cable.

1. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or
online from http://www.gedigitalenergy.com/multilin

2. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

3. Click the Quick Connect button to open the Quick Connect dialog box.

). See the Software Installation section if not already installed.

4. Select the Serial interface and the correct COM Port, then click Connect.

5. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named
“Quick Connect” and displays them at the upper-left of the screen. Expand the sections to view data directly from the
D30 device.

Each time that the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communi­cations to the D30 device. This ensures that configuration of the EnerVista UR Setup software matches the D30 model
number.

b) USING QUICK CONNECT VIA THE REAR ETHERNET PORTS

To use the Quick Connect feature to access the D30 from a computer through Ethernet, first assign an IP address to the
relay from the front panel keyboard.

1. Press the MENU key until the SETTINGS menu displays.

2. Navigate to the

3. Enter an IP address, for example “1.1.1.1,” and select the ENTER key to save the value.

4. In the same menu, select the SUBNET IP MASK setting.

5. Enter a subnet IP address, for example “255.0.0.0,” and press the ENTER key to save the value.

SETTINGS  PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting.

1-10 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

842799A1.CDR

END 1 END 2
Pin Wire color Diagram Pin Wire color Diagram

1 White/orange 1 White/green
2 Orange 2 Green

3 White/green 3 White/orange
4 Blue 4 Blue
5 White/blue 5 White/blue
6 Green 6 Orange
7 White/brown 7 White/brown
8 Brown 8 Brown

1

2

3

4

5

6

7

8

Next, use an Ethernet cross-over cable to connect the computer to the rear Ethernet port. In case you need it, the figure
shows the pinout for an Ethernet cross-over cable.

Figure 1–6: ETHERNET CROSS-OVER CABLE PIN LAYOUT

Now, assign the computer an IP address compatible with the relay’s IP address.

1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con-

nections window.

1

2. Right-click the Local Area Connection icon and select Properties.

GE Multilin D30 Line Distance Protection System 1-11

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

3. Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button.

1

4. Click the “Use the following IP address” box.

5. Enter an IP address with the first three numbers the same as the IP address of the D30 relay and the last number dif­ferent (in this example, 1.1.1.2).

6. Enter a subnet mask equal to the one set in the D30 (in this example, 255.0.0.0).

7. Click the OK button to save the values.

Before continuing, test the Ethernet connection.

1. Open a Windows console window by selecting Start > Run from the Windows Start menu and typing “cmd”.

2. Type the following command, substituting the IP address of 1.1.1.1 with yours:

C:\WINNT>ping 1.1.1.1

3. If the connection is successful, the system returns four replies similar to the following:

Pinging 1.1.1.1 with 32 bytes of data:

Reply from 1.1.1.1: bytes=32 time<10ms TTL=255
Reply from 1.1.1.1: bytes=32 time<10ms TTL=255
Reply from 1.1.1.1: bytes=32 time<10ms TTL=255
Reply from 1.1.1.1: bytes=32 time<10ms TTL=255

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

4. Note that the values for time and TTL vary depending on local network configuration.

5. If the following sequence of messages appears when entering the

C:\WINNT>ping 1.1.1.1 command:

1-12 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

Pinging 1.1.1.1 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

verify the physical connection between the D30 and the computer, and double-check the programmed IP address in

PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.

the

6. If the following sequence of messages appears when entering the

Pinging 1.1.1.1 with 32 bytes of data:

Hardware error.
Hardware error.
Hardware error.
Hardware error.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

C:\WINNT>ping 1.1.1.1 command:

verify the physical connection between the D30 and the computer, and double-check the programmed IP address in

PRODUCT SETUP  COMMUNICATIONS  NETWORK  IP ADDRESS setting, then repeat step 2.

the

7. If the following sequence of messages appears when entering the

Pinging 1.1.1.1 with 32 bytes of data:

Destination host unreachable.
Destination host unreachable.
Destination host unreachable.
Destination host unreachable.

Ping statistics for 1.1.1.1:

Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

Approximate round trip time in milliseconds:

Minimum = 0ms, Maximum = 0ms, Average = 0 ms

Pinging 1.1.1.1 with 32 bytes of data:

C:\WINNT>ping 1.1.1.1 command:

verify the IP address is programmed in the local computer by entering the ipconfig command in the command window.

C:\WINNT>ipconfig

Windows 2000 IP Configuration

Ethernet adapter <F4FE223E-5EB6-4BFB-9E34-1BD7BE7F59FF>:

Connection-specific DNS suffix. . :

IP Address. . . . . . . . . . . . : 0.0.0.0

Subnet Mask . . . . . . . . . . . : 0.0.0.0

Default Gateway . . . . . . . . . :

Ethernet adapter Local Area Connection:

Connection-specific DNS suffix . :

IP Address. . . . . . . . . . . . : 1.1.1.2

Subnet Mask . . . . . . . . . . . : 255.0.0.0

Default Gateway . . . . . . . . . :

C:\WINNT>

It can be necessary to restart the computer for the change in IP address to take effect (Windows 98 or NT).

1

GE Multilin D30 Line Distance Protection System 1-13

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

Before using the Quick Connect feature through the Ethernet port, disable any configured proxy settings in Internet
Explorer.

1

1. Start the Internet Explorer software.

2. Select the Tools > Internet Options menu item and click the Connections tab.

3. Click on the LAN Settings button to open the following window.

4. Ensure that the “Use a proxy server for your LAN” box is not checked.

If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been discon­nected from the D30 relay.

1. Start the Internet Explorer software.

2. Select the “UR” device from the EnerVista Launchpad to start EnerVista UR Setup.

3. Click the Quick Connect button to open the Quick Connect dialog box.

4. Select the Ethernet interface and enter the IP address assigned to the D30, then click the Connect button. The
EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick
Connect” and displays them at the upper-left of the screen.

5. Expand the sections to view data directly from the D30 device.

Each time the EnerVista UR Setup software is initialized, click the Quick Connect button to establish direct communica­tions to the D30. This ensures that configuration of the EnerVista UR Setup software matches the D30 model number.

When direct communications with the D30 via Ethernet is complete, make the following changes:

1. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con­nections window.

2. Right-click the Local Area Connection icon and select the Properties item.

3. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button.

1-14 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.3 ENERVISTA UR SETUP SOFTWARE

4. Set the computer to “Obtain a relay address automatically” as shown.

If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been discon­nected from the D30 relay.

AUTOMATIC DISCOVERY OF ETHERNET DEVICES

The EnerVista UR Setup software can automatically discover and communicate to all UR-series IEDs located on an Ether­net network.

Using the Quick Connect feature, a single click of the mouse triggers the software to automatically detect any UR-series
relays located on the network. The EnerVista UR Setup software then proceeds to configure all settings and order code
options in the Device Setup menu. This feature allows the user to identify and interrogate all UR-series devices at a loca­tion.

1

1.3.5 CONNECTING TO THE D30 RELAY

When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the
device.

GE Multilin D30 Line Distance Protection System 1-15

1.3 ENERVISTA UR SETUP SOFTWARE 1 GETTING STARTED

842743A3.CDR

Communications status indicators:

Green = OK
Red = No communications
UR icon = report is open

Quick action hot links

Expand the site list by double-clicking
or selecting the +/– box.

NOTE

1. Open the Display Properties window through the Site List tree as shown. The Display Properties window opens with a
status indicator on the lower left of the EnerVista UR Setup window.

1

2. If the status indicator is red, verify that the Ethernet network cable is properly connected to the Ethernet port on the
back of the relay and that the relay has been properly setup for communications (steps A and B earlier).

If a relay icon appears in place of the status indicator, than a report (such as an oscillography or event record) is open.
Close the report to re-display the green status indicator.

3. The Display Properties settings can now be edited, printed, or changed.

See chapter 4 in this manual or the EnerVista UR Setup Help File for information about the using the EnerVista UR
Setup software interface.

QUICK ACTION HOT LINKS

The EnerVista UR Setup software has several quick action buttons to provide instant access to several functions that are
often performed when using D30 relays. From the online window, users can select the relay to interrogate from a pull-down
window, then click the button for the action they want to perform. The following quick action functions are available:

• View the D30 event record

• View the last recorded oscillography record

• View the status of all D30 inputs and outputs

• View all of the D30 metering values

• View the D30 protection summary

• Generate a service report

1-16 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.4 UR HARDWARE

EnerVista

Ethernet
10/100 Mbps

Regional

control

center

Modem

Remote

communications link
Local
control

Engineer

GE Multilin F485
communications converter

UR-series IED

Troubleshooting
Commissioning
Setting changes

Reports

RS485 115 kbps

RS232

EnerVista

EnerVista

842759A2.CDR

1.4UR HARDWARE 1.4.1 MOUNTING AND WIRING

See Chapter 3: Hardware for mounting and wiring instructions.

1.4.2 COMMUNICATIONS

The EnerVista UR Setup software communicates to the relay via the faceplate RS232 port or the rear panel RS485 / Ether­net ports. To communicate via the faceplate RS232 port, a standard straight-through serial cable is used. The DB-9 male
end is connected to the relay and the DB-9 or DB-25 female end is connected to the computer COM2 port as described in
the CPU communications ports section of chapter 3.

1

Figure 1–7: RELAY COMMUNICATION OPTIONS

To communicate through the D30 rear RS485 port from a computer RS232 port, the GE Multilin RS232/RS485 converter
box is required. This device (catalog number F485) connects to the computer using a straight-through serial cable. A
shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the D30 rear communications port. The converter
terminals (+, –, GND) are connected to the D30 communication module (+, –, COM) terminals. See the CPU communica-
tions ports section in chapter 3 for details. The line is terminated with an R-C network (that is, 120 Ω, 1 nF) as described in
the chapter 3.

All messages are displayed on a backlit liquid crystal display (LCD) to make them visible under poor lighting conditions.
While the keypad and display are not actively being used, the display defaults to user-defined messages. Any high-priority
event-driven message automatically overrides the default message and appears on the display.

1.4.3 FACEPLATE DISPLAY

GE Multilin D30 Line Distance Protection System 1-17

1.5 USING THE RELAY 1 GETTING STARTED

1.5USING THE RELAY 1.5.1 FACEPLATE KEYPAD

1

Display messages are organized into pages under the following headings: actual values, settings, commands, and targets.
The MENU key navigates through these pages. Each heading page is divided further into logical subgroups.

The MESSAGE keys navigate through the subgroups. The VALUE keys increment or decrement numerical setting values
when in programming mode. These keys also scroll through alphanumeric values in the text edit mode. Alternatively, val­ues can be entered with the numeric keypad.

The decimal key initiates and advances to the next character in text edit mode or enters a decimal point.
The HELP key can be pressed at any time for context-sensitive help messages.
The ENTER key stores altered setting values.

1.5.2 MENU NAVIGATION

Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a
header display page menu item. Each press of the MENU key advances through the following main heading pages:

• Actual values

• Settings

• Commands

• Targets

• User displays (when enabled)

1.5.3 MENU HIERARCHY

The setting and actual value messages are arranged hierarchically. The header display pages are indicated by double
scroll bar characters (), while sub-header pages are indicated by single scroll bar characters (). The header display
pages represent the highest level of the hierarchy and the sub-header display pages fall below this level. The MESSAGE
UP and DOWN keys move within a group of headers, sub-headers, setting values, or actual values. Continually pressing
the MESSAGE RIGHT key from a header display displays specific information for the header category. Conversely, contin­ually pressing the MESSAGE LEFT key from a setting value or actual value display returns to the header display.

HIGHEST LEVEL LOWEST LEVEL (SETTING

VALUE )

 SETTINGS
 PRODUCT SETUP

 SETTINGS
 SYSTEM SETUP

The relay is in the default “Not Programmed” state when it leaves the factory. When powered up successfully, the Trouble
LED is on and the In Service LED off. The relay in the “Not Programmed” state blocks signaling of any output relay. These
conditions remain until the relay is explicitly put in the “Programmed” state.

Select the menu message

RELAY SETTINGS:
Not Programmed

SETTINGS  PRODUCT SETUP  INSTALLATION  RELAY SETTINGS

 SECURITY


ACCESS LEVEL:
Restricted

1.5.4 RELAY ACTIVATION

1. To put the relay in the “Programmed” state, press either of the VALUE keys once and then press ENTER. The face­plate Trouble LED turns off and the In Service LED turns on.

1-18 D30 Line Distance Protection System GE Multilin

1 GETTING STARTED 1.5 USING THE RELAY

NOTE

The settings for the relay can be programmed manually (see Chapter 5) via the faceplate keypad or remotely via the
EnerVista UR Setup software (see the EnerVista UR Setup help file).

1.5.5 RELAY PASSWORDS

It is recommended that passwords be set for each security level and assigned to specific personnel. There are two user
security access levels, COMMAND and SETTING.

1. COMMAND

The COMMAND access level restricts the user from making any settings changes, but allows the user to perform the fol­lowing operations:

• Operate breakers via faceplate keypad

• Change state of virtual inputs

• Clear event records

• Clear oscillography records

• Operate user-programmable pushbuttons

2. SETTING

The SETTING access level allows the user to make any changes to any of the setting values.

See the Changing Settings section in Chapter 4 for complete instructions on setting security-level passwords.

1.5.6 FLEXLOGIC CUSTOMIZATION

1

FlexLogic equation editing is required for setting user-defined logic for customizing the relay operations. See the FlexLogic
section in Chapter 5.

GE Multilin D30 Line Distance Protection System 1-19

1.5 USING THE RELAY 1 GETTING STARTED

1.5.7 COMMISSIONING

1

The D30 requires minimal maintenance after it is commissioned into service. Since the D30 is a microprocessor-based
relay, its characteristics do not change over time. As such, no further functional tests are required. Expected service life is
20 years for UR devices manufactured June 2014 or later when applied in a controlled indoors environment and electrical
conditions within specification.

The D30 performs a number of continual self-tests and takes the necessary action in case of any major errors (see the
Relay Self-tests section in chapter 7). However, it is recommended that D30 maintenance be scheduled with other system
maintenance. This maintenance can involve in-service, out-of-service, or unscheduled maintenance.

In-service maintenance:

1. Visual verification of the analog values integrity, such as voltage and current (in comparison to other devices on the
corresponding system).

2. Visual verification of active alarms, relay display messages, and LED indications.

3. LED test.

4. Visual inspection for any damage, corrosion, dust, or loose wires.

5. Event recorder file download with further events analysis.

Out-of-service maintenance:

1. Check wiring connections for firmness.

2. Analog values (currents, voltages, RTDs, analog inputs) injection test and metering accuracy verification. Calibrated
test equipment is required.

3. Protection elements setting verification (analog values injection or visual verification of setting file entries against relay
settings schedule).

4. Contact inputs and outputs verification. This test can be conducted by direct change of state forcing or as part of the
system functional testing.

5. Visual inspection for any damage, corrosion, or dust.

6. Event recorder file download with further events analysis.

7. LED Test and pushbutton continuity check.

Unscheduled maintenance, such as a disturbance causing system interruption:

1. View the event recorder and oscillography or fault report for correct operation of inputs, outputs, and elements.

If it is concluded that the relay or one of its modules is of concern, contact GE Multilin for service.

1-20 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

2 PRODUCT DESCRIPTION 2.1INTRODUCTION 2.1.1 OVERVIEW

The D30 Line Distance Protection System is a microprocessor-based relay intended for use on transmission lines of any
voltage level, without, with, and in the vicinity of series compensation, in three-pole tripping applications. The primary func­tion of the relay consists of five phase and ground distance zones of protection, either mho or quadrilateral as per user
selection. The distance elements are optimized to provide good measurement accuracy with a fast operating time, even
when used with capacitive voltage transformers, and can be supervised by detection of power swings. The relay also pro­vides directional ground overcurrent elements, which are commonly used as part of an overall line protection system.

D30 phase distance zones can be configured to work with voltages and currents fed from VTs and CTs located indepen­dently from one another on either side of a three-phase power transformer. The relay compensates accordingly to preserve
reach and correct target information regardless of the location and type of fault. This feature allows backup protection appli­cations for generators and power transformers.

A close-into-fault (or switch-on-to-fault) function is performed by the line pickup element. Out-of-step tripping, three-pole
autoreclosing, synchrocheck, fault location, and many other functions are also available. In addition, overcurrent and
undervoltage protection, fault diagnostics, power metering, and RTU functions are provided. The D30 provides phase, neu­tral, and ground time overcurrent protection. The time overcurrent functions can be programmed with multiple curve shapes
or FlexCurve™ for optimum coordination.

Voltage, current, and power metering is built into the relay as a standard feature. Current parameters are available as total
waveform RMS magnitude, or as fundamental frequency only RMS magnitude and angle (phasor).

Diagnostic features include an event recorder capable of storing 1024 time-tagged events, oscillography capable of storing
up to 64 records with programmable trigger, content and sampling rate, and data logger acquisition of up to 16 channels,
with programmable content and sampling rate. The internal clock used for time-tagging can be synchronized with an IRIG­B signal, using the Simple Network Time Protocol (SNTP) over the Ethernet port, or using the Precision Time Protocol
(PTP). This precise time stamping allows the sequence of events to be determined throughout the system. Events can also
be programmed (via FlexLogic™ equations) to trigger oscillography data capture which may be set to record the measured
parameters before and after the event for viewing on a personal computer (PC). These tools significantly reduce trouble­shooting time and simplify report generation in the event of a system fault.

Several options are available for communication. A faceplate RS232 port can be used to connect to a computer for the pro­gramming of settings and the monitoring of actual values. The RS232 port has a fixed baud rate of 19.2 kbps. The rear
RS485 port allows independent access by operating and engineering staff. It can be connected to system computers with
baud rates up to 115.2 kbps. All serial ports use the Modbus RTU protocol. The 100Base-FX or 100Base-T Ethernet inter­face provides fast, reliable communications in noisy environments. The Ethernet port supports IEC 61850, Modbus/TCP,
and TFTP protocols, PTP (according to IEEE Std. 1588-2008 or IEC 61588), and allows access to the relay via any stan­dard web browser (D30 web pages). The IEC 60870-5-104 protocol is supported on the Ethernet port, and DNP 3.0 and
IEC 60870-5-104 cannot be enabled at the same time. The Ethernet port also supports the Parallel Redundancy Protocol
(PRP) of IEC 62439-3 (clause 4, 2012) when purchased as an option.

Settings and actual values can be accessed from the front panel or EnerVista software.
The D30 IEDs use flash memory technology which allows field upgrading as new features are added. The following single

line diagram illustrates the relay functionality using ANSI (American National Standards Institute) device numbers.

2

GE Multilin D30 Line Distance Protection System 2-1

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

837764A3.CDR

50N

(2)

51N

(2)

67N/G

(2)

21G

(5)

59P

27P

(3)

59N

(3)

52

79

50P

(2)

50_2

(2)51(2)

51_2

(2)

21P

(5)

67P

(2)

67_2

(2)

68

59X

78

27X

50G

(2)

51G

(2)

50DD

Monitoring

D30 Line Distance Protection System

Close Trip

25 (4)

Transducer

Inputs

Metering

59_2

(3)

Table 2–1: DEVICE NUMBERS AND FUNCTIONS

2

DEVICE
NUMBER

21G Ground Distance 51P Phase Time Overcurrent
21P Phase Distance 51_2 Negative Sequence Time Overcurrent
25 Synchrocheck 52 AC Circuit Breaker
27P Phase Undervoltage 59N Neutral Overvoltage
27X Auxiliary Undervoltage 59P Phase Overvoltage
49 Thermal Overload Protection 59X Auxiliary Overvoltage
50DD Current Disturbance Detector 59_2 Negative Sequence Overvoltage
50G Ground Instantaneous Overcurrent 67N Neutral Directional Overcurrent
50N Neutral Instantaneous Overcurrent 67P Phase Directional Overcurrent
50P Phase Instantaneous Overcurrent 67_2 Negative Sequence Directional Overcurrent
50_2 Negative Sequence Instantaneous Overcurrent 68 Power Swing Blocking
51G Ground Time Overcurrent 78 Out-of-Step Tripping
51N Neutral Time Overcurrent 79 Automatic Recloser

FUNCTION DEVICE

NUMBER

FUNCTION

Figure 2–1: SINGLE LINE DIAGRAM

Table 2–2: OTHER DEVICE FUNCTIONS

FUNCTION FUNCTION FUNCTION

Breaker arcing current (I

Breaker control Fault locator Time synchronization over SNTP
Broken conductor detection FlexElements™ (8) Transducer inputs and outputs
Contact inputs (up to 96) FlexLogic equations Trip bus
Contact outputs (up to 64) IEC 61850 communications (optional) User-definable displays
Control pushbuttons Line pickup User-programmable LEDs
CyberSentry™ security Metering: current, voltage, power, power

Digital counters (8) Modbus communications User-programmable self-tests
Digital elements (48) Modbus user map Virtual inputs (64)

2-2 D30 Line Distance Protection System GE Multilin

2

t) Fault detector and fault report Time synchronization over IRIG-B or

factor, frequency

IEEE 1588

User-programmable pushbuttons

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

NOTE

Table 2–2: OTHER DEVICE FUNCTIONS

FUNCTION FUNCTION FUNCTION

Direct inputs and outputs (32) Non-volatile latches Virtual outputs (96)
Disconnect switches Non-volatile selector switch VT fuse failure
DNP 3.0 or IEC 60870-5-104 protocol Oscillography
Event recorder Setting groups (6)

2.1.2 ORDERING

a) OVERVIEW

The D30 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit and consists of the following mod­ules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications.
Each of these modules can be supplied in a number of configurations specified at the time of ordering. The information
required to completely specify the relay is provided in the following tables (see chapter 3 for full details of relay modules).

Order codes are subject to change without notice. See the GE Multilin ordering page at

http://www.gedigitalenergy.com/multilin/order.htm for the latest options.

The order code structure is dependent on the mounting option (horizontal or vertical) and the type of CT/VT modules
(enhanced diagnostic CT/VT modules or HardFiberTM process bus modules). The order code options are described in the
following sub-sections.

b) ORDER CODES WITH ENHANCED CT/VT MODULES

The order codes for the horizontal mount units are shown below.

Table 2–3: D30 ORDER CODES (HORIZONTAL UNITS)

BASE UNIT D30 | | | | | | | | | | | Base Unit
CPU T | | | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)

D30 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

U | | | | | | | | | | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-F X Ethernet, multimode, SFP with LC
V | | | | | | | | | | RS485 with 3 100Base-T Ethernet, S FP with RJ-45

2

GE Multilin D30 Line Distance Protection System 2-3

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

Table 2–3: D30 ORDER CODES (HORIZONTAL UNITS)

SOFTWARE 00 | | | | | | | | | No Software Options

(CyberSentry Lvl 1)

(IEEE 1588)

(IEEE1588+Cyber Sentry Lvl 1)

MOUNT/COATING H | | | | | | | | Horizontal (19” rack)

FACEPLATE/ DISPLAY C | | | | | | | English display

2

POWER SUPPLY
(redundant supply must
be same type as main supply)

ENHANCED DIAGNOSTIC CT/VT DSP 8L | | | | | Standard 4CT/4VT with enhanced diagnostics
(requires all DSPs to be enhanced diagnostic) 8M | | | | | Sensitive Ground 4CT/4VT with enhanced diagnostics
DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module

TRANSDUCER
INPUTS/OUTPUTS
(select a maximum of 3 per unit)

INTER-RELAY
COMMUNICATIONS
(select a maximum of 1 per unit)

D30 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

03 | | | | | | | | | IEC 61850; not available for Type E CPUs
A0 | | | | | | | | | CyberSentry Lvl 1
A3 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850
B0 | | | | | | | | | IEEE 1588
B3 | | | | | | | | | IEEE 1588 and IEC 61850
D0 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1

D3 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850

A | | | | | | | | Horizontal (19” rack) with harsh environmental coating

D | | | | | | | French display
R | | | | | | | Russian display
A | | | | | | | Chinese display
P | | | | | | | English display wi th 4 small and 12 large programmable pushbuttons
G | | | | | | | French display with 4 small and 12 large progr ammable pushbuttons
S | | | | | | | Russian display wit h 4 small and 12 large programmable pushbuttons
B | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttons
K | | | | | | | Enhanced front panel with English display
M | | | | | | | Enhanced front panel with French display
Q | | | | | | | Enhanced front panel with Russian display
U | | | | | | | Enhanced front panel with Chinese display
L | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | | | Enhanced front panel with Turkish display
Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

H | | | | | | 125 / 250 V AC/DC power supply
H | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supply
L | | | | | | 24 to 48 V (DC only) power supply
L | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply

4A 4A 4A 4A 4A 4 Soli d-State (no mon itoring) MOSFET outputs
4B 4B 4B 4B 4B 4 Soli d-State (voltage with opt ional current) MOSFET outputs
4C 4C 4C 4C 4C 4 Soli d-State (cur rent with optional voltage) MOSFET outputs
4D 4D 4D 4D 4D 16 digital inputs with Auto-Burnishing
4L 4L 4L 4L 4L 14 Form-A (no monitoring) Latching outputs
67 67 67 67 67 8 Form-A (no monitoring) outputs
6A 6A 6A 6A 6A 2 For m-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 6B 6B 6B 6B 2 For m-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 6C 6C 6C 6C 8 For m-C outputs
6D 6D 6D 6D 6D 16 digital inputs
6E 6E 6E 6E 6E 4 For m-C outputs, 8 digital inputs
6F 6F 6F 6F 6F 8 Fast Form-C outputs
6G 6G 6G 6G 6G 4 Form-A (voltage with optional current) outputs, 8 digital inputs
6H 6H 6H 6H 6H 6 For m-A (voltage with optional current) outputs, 4 digital inputs
6K 6K 6K 6K 6K 4 For m-C and 4 Fast Form-C outputs
6L 6L 6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M 6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N 6N 6N 6N 4 For m-A (current with optional voltage) outputs, 8 digital inputs
6P 6P 6P 6P 6P 6 For m-A (current with optional voltage) outputs, 4 digital inputs
6R 6R 6R 6R 6R 2 For m-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S 6S 6S 6S 2 For m-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T 6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U 6U 6U 6U 6 For m-A (no monitoring) outputs, 4 digital inputs
6V 6V 6V 6V 6V 2 For m-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
5A 5A 5A 5A 5A 4 DCmA inp uts, 4 DCmA outputs (only one 5A module is allowed)
5C 5C 5C 5C 5C 8 RTD inputs
5D 5D 5D 5D 5D 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed)
5E 5E 5E 5E 5E 4 RTD inputs, 4 DCmA inputs
5F 5F 5F 5F 5F 8 DCmA inputs

2A C37.94SM, 130 0nm single-mode, ELED, 1 channel single-mode
2B C37.94SM, 130 0nm single-mode, ELED, 2 channel single-mode
2E Bi-ph ase, single channel
2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
72 1550 nm, single-mode, LASER, 1 Channel
73 1550 nm, single-mode, LASER, 2 Channel
74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, mult i-mode, LED, 1 Channel
7B 1300 nm, multi-mode, LED, 1 Channel
7C 1300 nm, single-mode, ELE D, 1 Channel
7D 1300 nm, single-mode, LAS ER, 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 Channels
7I 1300 nm, multi-mode, LED, 2 Channels
7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, LASER, 2 Channels
7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
7R G.703, 1 Channel
7S G.703, 2 Channels
7T RS422, 1 Channel

7W RS422, 2 Channels

2-4 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

The order codes for the reduced size vertical mount units are shown below.

Table 2–4: D30 ORDER CODES (REDUCED SIZE VERTICAL UNITS)

BASE UNIT D30 | | | | | | | | | Base Unit
CPU T | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)

SOFTWARE
(CyberSentry Lvl 1)

(IEEE 1588)

(IEEE1588+Cyber Sentry Lvl 1)

MOUNT/COATING V | | | | | | Vertical (3/4 rack)

FACEPLATE/ DISPLAY F | | | | | English display

POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply

ENHANCED DIAGNOSTIC CT/VT DSP 8L | | | Standard 4CT/4VT with enhanced diagnostics
(requires all DSPs to be enhanced diagnostic) 8M | | | Sensitive Ground 4CT/4VT with enhanced diagnostics
DIGITAL INPUTS/OUTPUTS XX XX XX No Module

TRANSDUCER
INPUTS/OUTPUTS
(select a maximum of 3 per unit)

INTER-RELAY
COMMUNICATIONS
(select a maximum of 1 per unit)
For the last module, slot P is used for digital and transducer
input/output modules; slot R is used for inter-relay
communications modules.

D30 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

U | | | | | | | | RS485 with 1 100Base- T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
V | | | | | | | | RS485 with 3 100Base-T Ethernet, SFP with RJ-45

00 | | | | | | | No Software Options
03 | | | | | | | IEC 61850; not available for Type E CPUs
A0 | | | | | | | CyberSentry Lvl 1
A3 | | | | | | | CyberSentry Lvl 1 and IEC 61850
B0 | | | | | | | IEEE 1588
B3 | | | | | | | IEEE 1588 and IEC 61850
D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D3 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850

B | | | | | | Vertical (3/4 rack) with harsh environmental coating

D | | | | | French display
R | | | | | Russian display
A | | | | | Chinese display
K | | | | | Enhanced front panel with English display
M | | | | | Enhanced front panel with French display
Q | | | | | Enhanced fron t panel with Russian display
U | | | | | Enhanced front panel with Chinese display
L | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | Enhanced front panel with Russian display and user-programmable pushbutt ons
V | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons

W | | | | | Enhanced front panel with Turkish display

Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

L | | | | 24 to 48 V (DC only) power supply

4A 4A 4A 4 Solid-State (no monitoring) MOSFET outputs
4B 4B 4B 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4C 4C 4 Solid-State (current with optional voltage) MOSFET outputs
4D 4D 4D 16 digital inputs with Auto-Burnishing
4L 4L 4L 14 Form-A (no monitoring) Latching outputs
67 67 67 8 Form-A (no monitoring) outputs
6A 6A 6A 2 Form-A (voltage with optional curr ent) and 2 Form-C outputs, 8 digital inputs
6B 6B 6B 2 Form-A (voltage with optional curr ent) and 4 Form-C outputs, 4 digital inputs
6C 6C 6C 8 Form-C outputs
6D 6D 6D 16 digital inputs
6E 6E 6E 4 Form-C outputs, 8 digital inputs
6F 6F 6F 8 Fast Form-C outputs
6G 6G 6G 4 Form-A (voltage with optional current) outp uts, 8 digital inputs
6H 6H 6H 6 Form-A (voltage with optional current) outputs, 4 digital inputs
6K 6K 6K 4 Form-C and 4 Fast Fo rm-C outputs
6L 6L 6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M 6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N 6N 4 Form-A (current with optional voltage) outputs, 8 digital inputs
6P 6P 6P 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 6R 6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S 6S 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T 6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U 6U 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 6V 6V 2 Form-A outputs, 1 Form-C output , 2 Form-A (no monitoring) latching outputs, 8 digital inputs
5A 5A 5A 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed)
5C 5C 5C 8 RTD inputs
5D 5D 5D 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed)
5E 5E 5E 4 RTD inputs, 4 DCmA inputs
5F 5F 5F 8 DCmA inputs

2A C37.94SM, 1 300nm single-mode, ELED, 1 channel single-mode
2B C37.94SM, 1 300nm single-mode, ELED, 2 channel single-mode
2E Bi- phase, single channel

2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
72 1550 nm, single-mode, LASER, 1 Channel
73 1550 nm, single-mode, LASER, 2 Channel
74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, multi-mode, LED, 1 Channel
7B 1300 nm, multi-mode, LED, 1 Channel
7C 1300 nm, single-mode, ELED, 1 Channel
7D 1300 nm, single-mode, LASER , 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 Channels

7I 1300 nm, multi-mode, LED, 2 Channels
7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, LASER, 2 Channels
7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
7R G.703, 1 Channel
7S G.703, 2 Channels
7T RS422, 1 Channel
7W RS422, 2 Channels

2

c) ORDER CODES WITH PROCESS BUS MODULES

The order codes for the horizontal mount units with the process bus module are shown below.

Table 2–5: D30 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS)

BASE UNIT D30 | | | | | | | | | | | Base Unit
CPU T | | | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)

SOFTWARE 00 | | | | | | | | | No Software Options

D30 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

U | | | | | | | | | | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-F X Ethernet, multimode, SFP with LC
V | | | | | | | | | | RS485 with 3 100Base-T Ethernet, S FP with RJ-45

03 | | | | | | | | | IEC 61850; not available for Type E CPUs
A0 | | | | | | | | | CyberSentry Lvl 1
A3 | | | | | | | | | CyberSentry Lvl 1 and IEC 61850
B0 | | | | | | | | | IEEE 1588
B3 | | | | | | | | | IEEE 1588 and IEC 61850
D0 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D3 | | | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850

GE Multilin D30 Line Distance Protection System 2-5

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

Table 2–5: D30 ORDER CODES (HORIZONTAL UNITS WITH PROCESS BUS)

MOUNT/COATING H | | | | | | | | Horizontal (19” rack)

FACEPLATE/ DISPLAY C | | | | | | | English display

2

POWER SUPPLY
(redundant supply must
be same type as main supply)

PROCESS BUS MODULE | 81 | | | | Standard 4CT/4VT
DIGITAL INPUTS/OUTPUTS XX XX XX XX XX No Module

INTER-RELAY
COMMUNICATIONS
(select a maximum of 1 per unit)

D30 - * ** - * * * - F ** - H ** - M ** - P ** - U ** - W/X ** Full Size Horizontal Mount

A | | | | | | | | Horizontal (19” rack) with harsh environmental coating

D | | | | | | | French display
R | | | | | | | Russian display
A | | | | | | | Chinese display
P | | | | | | | English display with 4 small and 12 large programmable pushbuttons
G | | | | | | | French display with 4 small and 12 large programmable pushbuttons
S | | | | | | | Russian display with 4 small and 12 large programmable pushbuttons
B | | | | | | | Chinese display with 4 small and 12 large programmable pushbuttons
K | | | | | | | Enhanced front panel with English display
M | | | | | | | Enhanced front panel with French display
Q | | | | | | | Enhanced front panel with Russian display
U | | | | | | | Enhanced front panel with Chinese display
L | | | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | | | Enhanced front panel with Turkish display
Y | | | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

H | | | | | | 125 / 250 V AC/DC power supply
H | | | | | RH 125 / 250 V AC/DC with redundant 125 / 250 V AC/DC power supply
L | | | | | | 24 to 48 V (DC only) power supply
L | | | | | RL 24 to 48 V (DC only) with redundant 24 to 48 V DC power supply

4A 4A | 4 Solid-State (no monitoring) MOSFET outputs
4B 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
4C 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
4D 4D | 16 digital inputs with Auto-Burnishing
4L 4L | 14 Form-A (no monitoring) Latching outputs
67 67 | 8 Form-A (no monitoring) outputs
6A 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 6C | 8 Form-C outputs
6D 6D | 16 digital inputs
6E 6E | 4 Form-C outputs, 8 digital inputs
6F 6F | 8 Fast Form-C outputs
6G 6G | 4 Form-A (voltage with option al current) outputs, 8 digital inputs
6H 6H | 6 Form-A (voltage with option al current) outputs, 4 digital inputs
6K 6K | 4 Form-C and 4 Fast Form-C outputs
6L 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inputs
6N 6N | 4 Form-A (current w ith optional voltage) outputs, 8 digital inputs
6P 6P | 6 Form-A (current with optional voltage) outputs, 4 digital inputs
6R 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 6T | 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6U | 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs

2A C37.94SM, 130 0nm single-mode, ELED, 1 channel single-mode
2B C37.94SM, 130 0nm single-mode, ELED, 2 channel single-mode
2E Bi-ph ase, single channel

2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels

72 1550 nm, single-mode, LASER, 1 Channel

73 1550 nm, single-mode, LASER, 2 Channel

74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER

75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER

76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel

77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, mult i-mode, LED, 1 Channel
7B 1300 nm, multi-mode, LED, 1 Channel
7C 1300 nm, single-mode, ELE D, 1 Channel
7D 1300 nm, single-mode, LAS ER, 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode

7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 Channels

7I 1300 nm, multi-mode, LED, 2 Channels

7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, LASER, 2 Channels

7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
7R G.703, 1 Channel
7S G.703, 2 Channels

7T RS422, 1 Channel
7W RS422, 2 Channels

The order codes for the reduced size vertical mount units with the process bus module are shown below.

Table 2–6: D30 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS)

BASE UNIT D30 | | | | | | | | | Base Unit
CPU T | | | | | | | | RS485 and Three Multi-mode fiber 100Base-FX (SFP with LC)

SOFTWARE 00 | | | | | | | No Software Options

MOUNT/COATING V | | | | | | Vertical (3/4 rack)

FACEPLATE/ DISPLAY F | | | | | English display

D30 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

U | | | | | | | | RS485 with 1 100Base- T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
V | | | | | | | | RS485 with 3 100Base-T Ethernet, SFP with RJ-45

03 | | | | | | | IEC 61850; not available for Type E CPUs
A0 | | | | | | | CyberSentry Lvl 1
A3 | | | | | | | CyberSentry Lvl 1 and IEC 61850
B0 | | | | | | | IEEE 1588
B3 | | | | | | | IEEE 1588 and IEC 61850
D0 | | | | | | | IEEE 1588 and CyberSentry Lvl 1
D3 | | | | | | | IEEE 1588 and CyberSentry Lvl 1 and IEC 61850

B | | | | | | Vertical (3/4 rack) with harsh environmental coating

D | | | | | French display
R | | | | | Russian display
A | | | | | Chinese display
K | | | | | Enhanced front panel with English display
M | | | | | Enhanced front panel with French display
Q | | | | | Enhanced front panel with Russian display
U | | | | | Enhanced front panel with Chinese display
L | | | | | Enhanced front panel with English display and user-programmable pushbuttons
N | | | | | Enhanced front panel with French display and user-programmable pushbuttons
T | | | | | Enhanced front panel with Russian display and user-programmable pushbuttons
V | | | | | Enhanced front panel with Chinese display and user-programmable pushbuttons
W | | | | | Enhanced front panel with Turkish display
Y | | | | | Enhanced front panel with Turkish display and user-programmable pushbuttons

2-6 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

Table 2–6: D30 ORDER CODES (REDUCED SIZE VERTICAL UNITS WITH PROCESS BUS)

POWER SUPPLY H | | | | 125 / 250 V AC/DC power supply

PROCESS BUS MODULE | 81 | | Standard 4CT/4VT
DIGITAL INPUTS/OUTPUTS XX XX XX No Module

INTER-RELAY
COMMUNICATIONS
(select a maximum of 1 per unit)
For the last module, slot P is used for digital
input/output modules; slot R is used for inter-relay
communications modules.

D30 - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)

L | | | | 24 to 48 V (DC only) power supply

4A 4 Sol id-State (no monitor ing) MOSFET outputs
4B 4 Sol id-State (voltage with opt ional current) MOSFET outputs
4C 4 Solid-State (current with optional voltage) MOSFET outputs
4D 16 digital inputs with Auto-Burnishing
4L 14 Form-A (no monitoring) Latching outputs
67 8 Form-A (no monitoring) outputs
6A 2 For m-A (voltage with optional current) and 2 Form-C outputs, 8 digital inputs
6B 2 For m-A (voltage with optional current) and 4 Form-C outputs, 4 digital inputs
6C 8 Form-C outputs
6D 16 digital inputs
6E 4 For m-C outputs, 8 digital inputs
6F 8 Fast Form-C outputs
6G 4 Form-A (voltage with optional current) outp uts, 8 digital inputs
6H 6 Form-A (voltage with opti onal current) outputs, 4 digital inputs
6K 4 For m-C and 4 Fast Form-C outputs
6L 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 digital inputs
6M 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 digital inpu ts
6N 4 Form-A (current w ith optional voltage) outputs, 8 digital inputs
6P 6 For m-A (current with optional voltage) outputs, 4 digital inputs
6R 2 Form-A (no monitoring) and 2 Form-C outputs, 8 digital inputs
6S 2 For m-A (no monitoring) and 4 Form-C outputs, 4 digital inputs
6T 4 Form-A (no monitoring) outputs, 8 digital inputs
6U 6 Form-A (no monitoring) outputs, 4 digital inputs
6V 2 For m-A outputs, 1 Form-C output, 2 Form-A (no monitoring) latching outputs, 8 digital inputs
2A C37.94SM, 1 300nm single-mode, ELED, 1 channel single-mode
2B C37.94SM, 1 300nm single-mode, ELED, 2 channel single-mode
2E Bi- phase, single channel
2F Bi-phase, dual channel
2G IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel

2H IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
72 1550 nm, single-mode, LASER, 1 Channel

73 1550 nm, single-mode, LASER, 2 Channel
74 Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
75 Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
76 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
77 IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
7A 820 nm, multi-mode, LED, 1 Channel
7B 1300 nm, multi-mode, LED, 1 Channel
7C 1300 nm, single-mode, ELED, 1 Channel
7D 1300 nm, single-mode, LASER, 1 Channel
7E Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
7F Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
7G Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 Channels

7I 1300 nm, multi-mode, LED, 2 Channels
7J 1300 nm, single-mode, ELED, 2 Channels
7K 1300 nm, single-mode, LASER, 2 Channels
7L Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
7M Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
7N Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
7P Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER
7Q Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
7R G.703, 1 Channel
7S G.703, 2 Channels
7T RS422, 1 Channel
7W RS422, 2 Channels

2

GE Multilin D30 Line Distance Protection System 2-7

2.1 INTRODUCTION 2 PRODUCT DESCRIPTION

NOTE

NOTE

2.1.3 REPLACEMENT MODULES

Replacement modules can be ordered separately. When ordering a replacement CPU module or faceplate, provide the
serial number of your existing unit.

Not all replacement modules may be applicable to the D30 relay. Only the modules specified in the order codes are
available as replacement modules.

2

Replacement module codes are subject to change without notice. See the ordering page at

http://www.gedigitalenergy.com/multilin/order.htm

for the latest options.

The replacement module order codes for the horizontal mount units are shown below.

Table 2–7: ORDER CODES FOR REPLACEMENT MODULES, HORIZONTAL UNITS

POWER SUPPLY (redundant supply only available in
horizontal units and must be same type as main
supply) (for redundant supply, must swap both power
supplies when switching from RH to SH)
CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC

FACEPLATE/DISPLAY | 3C | Horizontal faceplate with keypad and English display

CONTACT INPUTS AND OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs

CT/VT MODULES
(NOT AVAILABLE FOR THE C30)

INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode

TRANSDUCER
INPUTS/OUTPUTS

UR - ** - *

| SH A | 125 / 300 V AC/DC

| RL H | 24 to 48 V (DC only)

| U | RS485 with 1 100Base-T Ethernet, SFP RJ-45 + 2 100Base-FX Ethernet, multimode, SFP with LC
| V | RS485 with 3 100Base-T Ethernet, SFP with RJ-45

| 3D | Horizontal faceplate with keypad and French display
| 3R | Horizontal faceplate with keypad and Russian display
| 3A | Horizontal faceplate with keypad and Chinese display
| 3P | Horizontal faceplate with keypad, user-programmable pushbuttons, and English display
| 3G | Horizontal faceplate with keypad, user-programmable pushbuttons, and French display
| 3S | Horizontal faceplate with keypad, user-programmable pushbuttons, and Russian display
| 3B | Horizontal faceplate with keypad, user-programmable pushbuttons, and Chinese display
| 3K | Enhanced front panel with English display
| 3M | Enhanced fro nt panel with French display
| 3Q | Enhanced front panel with Russian display
| 3U | Enhanced front panel with Chinese display
| 3L | Enhanced front panel with English display and user-programmable pushbuttons
| 3N | Enhanced front panel with French display and user-programmable pushbuttons
| 3T | Enhanced front panel with Russian display and user-programmab le pushbuttons
| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons

| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
| 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
| 4D | 16 contact inputs with Auto-Burnishing
| 4L | 14 Form-A (no monitoring) Latching outputs
| 67 | 8 Form-A (no monitoring) outputs
| 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs
| 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs
| 6C | 8 Form-C outputs
| 6D | 16 contact inputs
| 6E | 4 Form-C outputs, 8 contact inputs
| 6F | 8 Fast Form-C outputs
| 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs
| 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs
| 6K | 4 Form-C and 4 Fast Form-C outputs
| 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs
| 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs
| 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs
| 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs
| 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs
| 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs
| 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs
| 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs
| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A ( no monitoring) latching outputs, 8 contact inputs
| 8L | Standard 4CT/4VT with enhanced diagnostics
| 8N | Standard 8CT with enhanced diagnostics
| 8M | Sensitive Ground 4CT/4VT with enhanced diagnostics
| 8R | Sensitive Ground 8CT with enhanced diagnostics

| 2B | C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode
| 2E | Bi-phase, single channel
| 2F | Bi-phase, dual channel
| 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
| 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
| 72 | 1550 nm, single-mode, LASER, 1 Channel
| 73 | 1550 nm, single-mode, LASER, 2 Channel
| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
| 76 | IEEE C37.94, 820 nm, multimode, LED, 1 Channel
| 77 | IEEE C37.94, 820 nm, multimode, LED, 2 Channels
| 7A | 820 nm, multi-mode, LED, 1 Channel
| 7B | 1300 nm, multi-mode, LED, 1 Channel
| 7C | 1300 nm, single-mode, ELED, 1 Channel
| 7D | 1300 nm, single-mode, LASER, 1 Channel
| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
| 7H | 820 nm, multi-mode, LED, 2 Channels
| 7I | 1300 nm, multi-mode, LED, 2 Channels
| 7J | 1300 nm, single-mode, ELED, 2 Channels
| 7K | 1300 nm, single-mode, LASER, 2 Channels
| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
| 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASE R
| 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
| 7R | G.703, 1 Channel
| 7S | G.703, 2 Channels
| 7T | RS422, 1 Channel
| 7W | RS422, 2 Channels
| 5A | 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed)
| 5C | 8 RTD inputs
| 5D | 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed)
| 5E | 4 DCmA inputs, 4 RTD inputs
| 5F | 8 DCmA inputs

2-8 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.1 INTRODUCTION

The replacement module order codes for the reduced-size vertical mount units are shown below.

Table 2–8: ORDER CODES FOR REPLACEMENT MODULES, VERTICAL UNITS

POWER SUPPLY | SH B | 125 / 300 V AC/DC

CPU | T | RS485 with 3 100Base-FX Ethernet, multimode, SFP with LC
FACEPLATE/DISPLAY | 3F | Vertical faceplate with keypad and English display

CONTACT INPUTS/OUTPUTS | 4A | 4 Solid-State (no monitoring) MOSFET outputs

CT/VT MODULES
(NOT AVAILABLE FOR THE C30)
INTER-RELAY COMMUNICATIONS | 2A | C37.94SM, 1300nm single-mode, ELED, 1 channel single-mode

TRANSDUCER
INPUTS/OUTPUTS

UR - ** - *

| RL V | 24 to 48 V (DC only)

| 3D | Vertical faceplate with keypad and French display
| 3R | Vertical faceplate with keypad and Russian display
| 3K | Vertical faceplate with keypad and Chinese display
| 3K | Enhanced front panel with English display
| 3M | Enhanced fro nt panel with French display
| 3Q | Enhanced front panel with Russian display
| 3U | Enhanced front panel with Chinese display
| 3L | Enhanced front panel with English display and user-programmable pushbuttons
| 3N | Enhanced front panel with French display and user-programmable pushbuttons
| 3T | Enhanced front panel with Russian display and user-programmable pushbut tons
| 3V | Enhanced front panel with Chinese display and user-programmable pushbuttons

| 4B | 4 Solid-State (voltage with optional current) MOSFET outputs
| 4C | 4 Solid-State (current with optional voltage) MOSFET outputs
| 4D | 16 contact inputs with Auto-Burnishing
| 4L | 14 Form-A (no monitoring) Latching outputs
| 67 | 8 Form-A (no monitoring) outputs
| 6A | 2 Form-A (voltage with optional current) and 2 Form-C outputs, 8 contact inputs
| 6B | 2 Form-A (voltage with optional current) and 4 Form-C outputs, 4 contact inputs
| 6C | 8 Form-C outputs
| 6D | 16 contact inputs
| 6E | 4 Form-C outputs, 8 contact inputs
| 6F | 8 Fast Form-C outputs
| 6G | 4 Form-A (voltage with optional current) outputs, 8 contact inputs
| 6H | 6 Form-A (voltage with optional current) outputs, 4 contact inputs
| 6K | 4 Form-C and 4 Fast Form-C outputs
| 6L | 2 Form-A (current with optional voltage) and 2 Form-C outputs, 8 contact inputs
| 6M | 2 Form-A (current with optional voltage) and 4 Form-C outputs, 4 contact inputs
| 6N | 4 Form-A (current with optional voltage) outputs, 8 contact inputs
| 6P | 6 Form-A (current with optional voltage) outputs, 4 contact inputs
| 6R | 2 Form-A (no monitoring) and 2 Form-C outputs, 8 contact inputs
| 6S | 2 Form-A (no monitoring) and 4 Form-C outputs, 4 contact inputs
| 6T | 4 Form-A (no monitoring) outputs, 8 contact inputs
| 6U | 6 Form-A (no monitoring) outputs, 4 contact inputs
| 6V | 2 Form-A outputs, 1 Form-C output, 2 Form-A ( no monitoring) latching outputs, 8 contact inputs
| 8L | Standard 4CT/4VT with enhanced diagnostics
| 8N | Standard 8CT with enhanced diagnostics

| 2B | C37.94SM, 1300nm single-mode, ELED, 2 channel single-mode
| 2E | Bi-phase, single channel
| 2F | Bi-phase, dual channel
| 2G | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 1 Channel
| 2H | IEEE C37.94, 820 nm, 128 kbps, multimode, LED, 2 Channels
| 72 | 1550 nm, single-mode, LASER, 1 Channel
| 73 | 1550 nm, single-mode, LASER, 2 Channel
| 74 | Channel 1 - RS422; Channel 2 - 1550 nm, single-mode, LASER
| 75 | Channel 1 - G.703; Channel 2 - 1550 nm, Single-mode LASER
| 76 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 1 Channel
| 77 | IEEE C37.94, 820 nm, 64 kbps, multimode, LED, 2 Channels
| 7A | 820 nm, multi-mode, LED, 1 Channel
| 7B | 1300 nm, multi-mode, LED, 1 Channel
| 7C | 1300 nm, single-mode, ELED, 1 Channel
| 7D | 1300 nm, single-mode, LASER, 1 Channel
| 7E | Channel 1 - G.703; Channel 2 - 820 nm, multi-mode
| 7F | Channel 1 - G.703; Channel 2 - 1300 nm, multi-mode
| 7G | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode ELED
| 7H | 820 nm, multi-mode, LED, 2 Channels
| 7I | 1300 nm, multi-mode, LED, 2 Channels
| 7J | 1300 nm, single-mode, ELED, 2 Channels
| 7K | 1300 nm, single-mode, LASER, 2 Channels
| 7L | Channel 1 - RS422; Channel 2 - 820 nm, multi-mode, LED
| 7M | Channel 1 - RS422; Channel 2 - 1300 nm, multi-mode, LED
| 7N | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, ELED
| 7P | Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASE R
| 7Q | Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER
| 7R | G.703, 1 Channel
| 7S | G.703, 2 Channels
| 7T | RS422, 1 Channel
| 7W | RS422, 2 Channels
| 5A | 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed)
| 5C | 8 RTD inputs
| 5D | 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed)
| 5E | 4 DCmA inputs, 4 RTD inputs
| 5F | 8 DCmA inputs

2

GE Multilin D30 Line Distance Protection System 2-9

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

NOTE

837717A1.CDR

Phase Element ( 21P)

0

5

10

15

20

25

30

0% 10% 20% 30% 40% 50% 60% 70% 80%

Fault Location [%]

OperatingTime [ms]

SIR = 0.1
SIR = 1
SIR = 10
SIR = 20
SIR = 30

2.2SPECIFICATIONSSPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

The operating times include the activation time of a trip rated form-A output contact unless otherwise indicated.
FlexLogic operands of a given element are 4 ms faster. Take this into account when using FlexLogic to interconnect
with other protection or control elements of the relay, building FlexLogic equations, or interfacing with other IEDs or

2

power system devices via communications or different output contacts. If not specified, operate times are given
here for a 60 Hz system at nominal system frequency. Operate times for a 50 Hz system are 1.2 times longer.

PHASE DISTANCE OPERATING TIME CURVES

The operating times are response times of a microprocessor part

PHASE DISTANCE

Characteristic: mho (memory polarized or offset) or

quad (memory polarized or non-direc­tional), selectable individually per zone

Number of zones: 5

Directionality: forward, reverse, or non-directional per

zone
Reach (secondary Ω): 0.02 to 500.00 Ω in steps of 0.01
Reach accuracy: ±5% including the effect of CVT tran-

sients up to an SIR of 30
Distance:

Characteristic angle: 30 to 90° in steps of 1
Comparator limit angle: 30 to 90° in steps of 1

Directional supervision:

Characteristic angle: 30 to 90° in steps of 1
Limit angle: 30 to 90° in steps of 1

Right blinder (Quad only):

Reach: 0.02 to 500 Ω in steps of 0.01
Characteristic angle: 60 to 90° in steps of 1

Left Blinder (Quad only):

Reach: 0.02 to 500 Ω in steps of 0.01

Characteristic angle: 60 to 90° in steps of 1
Time delay: 0.000 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

Current supervision:

Level: line-to-line current

Pickup: 0.050 to 30.000 pu in steps of 0.001

Dropout: 97 to 98%
Memory duration: 5 to 25 cycles in steps of 1
VT location: all delta-wye and wye-delta transformers
CT location: all delta-wye and wye-delta transformers
Voltage supervision pickup (series compensation applications):

0 to 5.000 pu in steps of 0.001

of the relay. See output contacts specifications for estimation of
the total response time for a particular application. The operating
times are average times including variables such as fault inception
angle or type of a voltage source (magnetic VTs and CVTs).

2.2.1 PROTECTION ELEMENTS

2-10 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

837718A1.CDR

Ground Element (21G)

0

5

10

15

20

25

30

35

0% 10% 20% 30% 40% 50% 60% 70% 80%

Fault Location [%]

Operating Time [ms]

SIR = 0 .1
SIR = 1
SIR = 10
SIR = 20
SIR = 30

GROUND DISTANCE

Characteristic: Mho (memory polarized or offset) or

Quad (memory polarized or non-direc­tional), selectable individually per zone

Reactance polarization: negative-sequence or zero-sequence

current
Non-homogeneity angle: –40 to 40° in steps of 1
Number of zones: 5
Directionality: forward, reverse, or non-directional per

zone
Reach (secondary Ω): 0.02 to 500.00 Ω in steps of 0.01
Distance characteristic angle: 30 to 90° in steps of 1
Distance comparator limit angle: 30 to 90° in steps of 1
Directional supervision:

Characteristic angle: 30 to 90° in steps of 1
Limit angle: 30 to 90° in steps of 1

Zero-sequence compensation

Z0/Z1 magnitude: 0.00 to 10.00 in steps of 0.01
Z0/Z1 angle: –90 to 90° in steps of 1

Zero-sequence mutual compensation

Z0M/Z1 magnitude: 0.00 to 7.00 in steps of 0.01
Z0M/Z1 angle: –90 to 90° in steps of 1

Right blinder (Quad only):

Reach: 0.02 to 500 Ω in steps of 0.01
Characteristic angle: 60 to 90° in steps of 1

Left blinder (Quad only):

Reach: 0.02 to 500 Ω in steps of 0.01

Characteristic angle: 60 to 90° in steps of 1
Time delay: 0.000 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

Current supervision:

Level: neutral current (3I_0)

Pickup: 0.050 to 30.000 pu in steps of 0.001

Dropout: 97 to 98%
Memory duration: 5 to 25 cycles in steps of 1
Voltage supervision pickup (series compensation applications):

0 to 5.000 pu in steps of 0.001

GROUND DISTANCE OPERATING TIME CURVES

The operating times are response times of a microprocessor part
of the relay. See output contacts specifications for estimation of
the total response time for a particular application. The operating
times are average times including variables such as fault inception
angle or type of a voltage source (magnetic VTs and CVTs).

LINE PICKUP

Phase instantaneous overcurrent: 0.000 to 30.000 pu
Undervoltage pickup: 0.000 to 3.000 pu
Overvoltage delay: 0.000 to 65.535 s

PHASE/NEUTRAL/GROUND TOC

Current: Phasor or RMS
Pickup level: 0.000 to 30.000 pu in steps of 0.001
Dropout level: 97% to 98% of pickup
Level accuracy:

0.1 to 2.0 × CT: ±0.5% of reading or ±0.4% of rated
(whichever is greater)

> 2.0 × CT: ±1.5% of reading > 2.0 × CT rating

Curve shapes: IEEE Moderately/Very/Extremely

Inverse; IEC (and BS) A/B/C and Short
Inverse; GE IAC Inverse, Short/Very/
Extremely Inverse; I
(programmable); Definite Time (0.01 s
base curve)

Curve multiplier: Time Dial = 0.00 to 600.00 in steps of

0.01

Reset type: Instantaneous/Timed (per IEEE)
Curve timing accuracy
at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle

(whichever is greater) from pickup to
operate

Voltage restraint: Modifies pickup current for voltage in the

range of 0.1<V<0.9 VT Nominal in a
fixed linear relationship

2

t; FlexCurves™

2

GE Multilin D30 Line Distance Protection System 2-11

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

PHASE/NEUTRAL/GROUND IOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy:

0.1 to 2.0 × CT rating: ±0.5% of reading or ±0.4% of rated
(whichever is greater)

> 2.0 × CT rating ±1.5% of reading

Overreach: <2%

2

Pickup delay: 0.00 to 600.00 s in steps of 0.01
Reset delay: 0.00 to 600.00 s in steps of 0.01
Operate time: <16 ms at 3 × pickup at 60 Hz

Timer accuracy: ±3% of operate time or ±1/4 cycle

(Phase/Ground IOC)
<20 ms at 3 × pickup at 60 Hz
(Neutral IOC)

(whichever is greater)

NEGATIVE SEQUENCE TOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001
Dropout level: 97% to 98% of pickup
Level accuracy: ±0.5% of reading or ±0.4% of rated

Curve shapes: IEEE Moderately/Very/Extremely

Curve multiplier (Time dial): 0.00 to 600.00 in steps of 0.01
Reset type: Instantaneous/Timed (per IEEE) and Lin-

Curve timing accuracy
at 1.03 to 20 x pickup: ±3.5% of operate time or ±½ cycle

(whichever is greater)
from 0.1 to 2.0 x CT rating
±1.5% of reading > 2.0 x CT rating

Inverse; IEC (and BS) A/B/C and Short
Inverse; GE IAC Inverse, Short/Very/
Extremely Inverse; I
(programmable); Definite Time (0.01 s
base curve)

ear

(whichever is greater) from pickup to
operate

2

t; FlexCurves™

NEGATIVE SEQUENCE IOC

Pickup level: 0.000 to 30.000 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy: 0.1 to 2.0 × CT rating: ±0.5% of reading

Overreach: <2%
Pickup delay: 0.00 to 600.00 s in steps of 0.01
Reset delay: 0.00 to 600.00 s in steps of 0.01
Operate time: <20 ms at 3 × pickup at 60 Hz
Timer accuracy: ±3% of operate time or ±1/4 cycle

or ±0.4% of rated (whichever is greater);
> 2.0 × CT rating: ±1.5% of reading

(whichever is greater)

PHASE DIRECTIONAL OVERCURRENT

Relay connection: 90° (quadrature)
Quadrature voltage: ABC phase seq.: phase A (V

B (V

), phase C (VAB); ACB phase

CA

seq.: phase A (V

phase C (V
Polarizing voltage threshold: 0.000 to 3.000 pu in steps of 0.001
Current sensitivity threshold: 0.05 pu
Characteristic angle: 0 to 359
Angle accuracy: ±2°
Operation time (FlexLogic operands):

° in steps of 1

Tripping (reverse load, forward fault):<

12 ms, typically

Blocking (forward load, reverse fault):<

8 ms, typically

BA

CB

)

), phase B (VAC),

), phase

BC

NEUTRAL DIRECTIONAL OVERCURRENT

Directionality: Co-existing forward and reverse
Polarizing: Voltage, Current, Dual
Polarizing voltage: V_0 or VX
Polarizing current: IG
Operating current: I_0
Level sensing: 3 × (|I_0| – K × |I_1|), IG
Restraint, K: 0.000 to 0.500 in steps of 0.001
Characteristic angle: –90 to 90° in steps of 1
Limit angle: 40 to 90° in steps of 1, independent for

forward and reverse
Angle accuracy: ±2°
Offset impedance: 0.00 to 250.00 Ω in steps of 0.01
Pickup level: 0.002 to 30.000 pu in steps of 0.01
Dropout level: 97 to 98%
Operation time: <16 ms at 3 × pickup at 60 Hz

NEGATIVE SEQUENCE DIRECTIONAL OC

Directionality: Co-existing forward and reverse
Polarizing: Voltage
Polarizing voltage: V_2
Operating current: I_2
Level sensing: Zero-sequence:|I_0| – K × |I_1|

Negative-sequence:|I_2| – K × |I_1|
Restraint, K: 0.000 to 0.500 in steps of 0.001
Characteristic angle: 0 to 90° in steps of 1
Limit angle: 40 to 90° in steps of 1, independent for

forward and reverse
Angle accuracy: ±2°
Offset impedance: 0.00 to 250.00 Ω in steps of 0.01
Pickup level: 0.015 to 30.000 pu in steps of 0.01
Dropout level: 97 to 98%
Operation time: <16 ms at 3 × pickup at 60 Hz

2-12 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

PHASE UNDERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001
Dropout level: 102 to 103% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Curve shapes: GE IAV Inverse;

Definite Time (0.1s base curve)

Curve multiplier: Time dial = 0.00 to 600.00 in steps of

0.01
Curve timing accuracy
at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle

(whichever is greater) from pickup to
operate

AUXILIARY UNDERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001
Dropout level: 102 to 103% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Curve shapes: GE IAV Inverse, Definite Time
Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01
Curve timing accuracy
at <0.90 x pickup: ±3.5% of operate time or ±1/2 cycle

(whichever is greater) from pickup to
operate

PHASE OVERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0.00 to 600.00 in steps of 0.01 s
Operate time: <30 ms at 1.10 × pickup at 60 Hz
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

NEUTRAL OVERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0.00 to 600.00 s in steps of 0.01 (definite

time) or user-defined curve
Reset delay: 0.00 to 600.00 s in steps of 0.01
Curve timing accuracy
at >1.1 x pickup: ±3.5% of operate time or ±1 cycle

(whichever is greater) from pickup to

operate
Operate time: <30 ms at 1.10 × pickup at 60 Hz

AUXILIARY OVERVOLTAGE

Pickup level: 0.000 to 3.000 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0 to 600.00 s in steps of 0.01
Reset delay: 0 to 600.00 s in steps of 0.01
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)
Operate time: <30 ms at 1.10 × pickup at 60 Hz

NEGATIVE SEQUENCE OVERVOLTAGE

Pickup level: 0.000 to 1.250 pu in steps of 0.001
Dropout level: 97 to 98% of pickup
Level accuracy: ±0.5% of reading from 10 to 208 V
Pickup delay: 0 to 600.00 s in steps of 0.01
Reset delay: 0 to 600.00 s in steps of 0.01
Timer accuracy: ±3% of operate time or ±20 ms, which-

ever is greater

Operate time: <30 ms at 1.10 × pickup at 60 Hz

BREAKER ARCING CURRENT

Principle: accumulates breaker duty (I2t) and mea-

sures fault duration

Initiation: programmable per phase from any Flex-

Compensation for auxiliary relays: 0 to 65.535 s in steps of 0.001
Alarm threshold: 0 to 50000 kA2-cycle in steps of 1
Fault duration accuracy: 0.25 of a power cycle
Availability: 1 per CT bank with a minimum of 2

Logic operand

SYNCHROCHECK

Max voltage difference: 0 to 400000 V in steps of 1
Max angle difference: 0 to 100
Max freq. difference: 0.00 to 2.00 Hz in steps of 0.01
Hysteresis for max. freq. diff.: 0.00 to 0.10 Hz in steps of 0.01
Dead source function: None, LV1 & DV2, DV1 & LV2, DV1 or

° in steps of 1

DV2, DV1 xor DV2, DV1 & DV2
(L = Live, D = Dead)

AUTORECLOSURE

Single breaker applications, 3-pole tripping schemes
Up to 4 reclose attempts before lockout
Independent dead time setting before each shot
Possibility of changing protection settings after each shot with

FlexLogic

POWER SWING DETECT

Functions: Power swing block, Out-of-step trip
Characteristic: Mho or Quad
Measured impedance: Positive-sequence
Blocking / tripping modes: 2-step or 3-step
Tripping mode: Early or Delayed
Current supervision:

Pickup level: 0.050 to 30.000 pu in steps of 0.001

Dropout level: 97 to 98% of pickup
Fwd / reverse reach (sec. Ω): 0.10 to 500.00 Ω in steps of 0.01
Left and right blinders (sec. Ω): 0.10 to 500.00 Ω in steps of 0.01
Impedance accuracy: ±5%
Fwd / reverse angle impedances: 40 to 90° in steps of 1
Angle accuracy: ±2°
Characteristic limit angles: 40 to 140° in steps of 1
Timers: 0.000 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

2

GE Multilin D30 Line Distance Protection System 2-13

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

LOAD ENCROACHMENT

Responds to: Positive-sequence quantities
Minimum voltage: 0.000 to 3.000 pu in steps of 0.001
Reach (sec. Ω): 0.02 to 250.00 Ω in steps of 0.01
Impedance accuracy: ±5%
Angle: 5 to 50° in steps of 1
Angle accuracy: ±2°
Pickup delay: 0 to 65.535 s in steps of 0.001

2

Reset delay: 0 to 65.535 s in steps of 0.001
Timer accuracy: ±3% of operate time or ±1/4 cycle

(whichever is greater)

Operate time: <30 ms at 60 Hz

FLEXLOGIC

Programming language: Reverse Polish Notation with graphical

Lines of code: 512
Internal variables: 64
Supported operations: NOT, XOR, OR (2 to 16 inputs), AND (2

Inputs: any logical variable, contact, or virtual

Number of timers: 32
Pickup delay: 0 to 60000 (ms, sec., min.) in steps of 1
Dropout delay: 0 to 60000 (ms, sec., min.) in steps of 1

visualization (keypad programmable)

to 16 inputs), NOR (2 to 16 inputs),
NAND (2 to 16 inputs), latch (reset-domi­nant), edge detectors, timers

input

FLEXCURVES™

Number: 4 (A through D)
Reset points: 40 (0 through 1 of pickup)
Operate points: 80 (1 through 20 of pickup)
Time delay: 0 to 65535 ms in steps of 1

FLEX STATES

Number: up to 256 logical variables grouped

under 16 Modbus addresses

Programmability: any logical variable, contact, or virtual

input

FLEXELEMENTS™

Number of elements: 8
Operating signal: any analog actual value, or two values in

Operating signal mode: signed or absolute value
Operating mode: level, delta
Comparator direction: over, under
Pickup Level: –90.000 to 90.000 pu in steps of 0.001
Hysteresis: 0.1 to 50.0% in steps of 0.1
Delta dt: 20 ms to 60 days
Pickup & dropout delay: 0.000 to 65.535 s in steps of 0.001

differential mode

THERMAL OVERLOAD PROTECTION

Thermal overload curves: IEC 255-8 curve
Base current: 0.20 to 3.00 pu in steps of 0.01
Overload (k) factor: 1.00 to 1.20 pu in steps of 0.05
Trip time constant: 0 to 1000 min. in steps of 1
Reset time constant: 0 to 1000 min. in steps of 1
Minimum reset time: 0 to 1000 min. in steps of 1
Timer accuracy (cold curve): ±100 ms or 2%, whichever is greater
Timer accuracy (hot curve): ±500 ms or 2%, whichever is greater

< 0.9 × k × Ib and I / (k × Ib) > 1.1

for I

p

TRIP BUS (TRIP WITHOUT FLEXLOGIC)

Number of elements: 6
Number of inputs: 16
Operate time: <2 ms at 60 Hz
Timer accuracy: ±3% or 10 ms, whichever is greater

2.2.2 USER PROGRAMMABLE ELEMENTS

NON-VOLATILE LATCHES

Type: set-dominant or reset-dominant
Number: 16 (individually programmed)
Output: stored in non-volatile memory
Execution sequence: as input prior to protection, control, and

FlexLogic

USER-PROGRAMMABLE LEDs

Number: 48 plus trip and alarm
Programmability: from any logical variable, contact, or vir-

tual input

Reset mode: self-reset or latched

LED TEST

Initiation: from any contact input or user-program-

mable condition
Number of tests: 3, interruptible at any time
Duration of full test: approximately 3 minutes
Test sequence 1: all LEDs on
Test sequence 2: all LEDs off, one LED at a time on for 1 s
Test sequence 3: all LEDs on, one LED at a time off for 1 s

USER-DEFINABLE DISPLAYS

Number of displays: 16
Lines of display: 2 × 20 alphanumeric characters
Parameters: up to 5, any Modbus register addresses
Invoking and scrolling: keypad, or any user-programmable con-

dition, including pushbuttons

CONTROL PUSHBUTTONS

Number of pushbuttons: 7
Operation: drive FlexLogic operands

USER-PROGRAMMABLE PUSHBUTTONS (OPTIONAL)

Number of pushbuttons: 12 (standard faceplate);

16 (enhanced faceplate)
Mode: self-reset, latched
Display message: 2 lines of 20 characters each
Drop-out timer: 0.00 to 60.00 s in steps of 0.05
Autoreset timer: 0.2 to 600.0 s in steps of 0.1
Hold timer: 0.0 to 10.0 s in steps of 0.1

2-14 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

SELECTOR SWITCH

Number of elements: 2
Upper position limit: 1 to 7 in steps of 1
Selecting mode: time-out or acknowledge
Time-out timer: 3.0 to 60.0 s in steps of 0.1
Control inputs: step-up and 3-bit
Power-up mode: restore from non-volatile memory or syn-

chronize to a 3-bit control input or synch/
restore mode

OSCILLOGRAPHY

Maximum records: 64
Sampling rate: 64 samples per power cycle
Triggers: any element pickup, dropout, or operate;

contact input change of state; contact
output change of state; FlexLogic equa­tion

Data: AC input channels; element state; con-

tact input state; contact output state

Data storage: in non-volatile memory

EVENT RECORDER

Capacity: 1024 events
Time-tag: to 1 microsecond
Triggers: any element pickup, dropout, or operate;

contact input change of state; contact
output change of state; self-test events

Data storage: in non-volatile memory

DIGITAL ELEMENTS

Number of elements: 48
Operating signal: any FlexLogic operand
Pickup delay: 0.000 to 999999.999 s in steps of 0.001
Dropout delay: 0.000 to 999999.999 s in steps of 0.001
Timing accuracy: ±3% or ±4 ms, whichever is greater

2.2.3 MONITORING

FAULT LOCATOR

Method: single-ended
Voltage source: wye-connected VTs, delta-connected

VTs and neutral voltage, delta-connected
VTs and zero-sequence current (approxi­mation)

Maximum accuracy if: fault resistance is zero or fault currents

from all line terminals are in phase
Relay accuracy: ±1.5% (V > 10 V, I > 0.1 pu)
Worst-case accuracy:

+ user data

VT

%error

+ user data

CT

%error

Z

Line%error

METHOD
RELAY ACCURACY

+ user data

+ see chapter 8

%error

+ (1.5%)

%error

2

RMS CURRENT: PHASE, NEUTRAL, AND GROUND

Accuracy at

0.1 to 2.0 × CT rating: ±0.25% of reading or ±0.1% of rated
(whichever is greater)

> 2.0 × CT rating: ±1.0% of reading

RMS VOLTAGE

Accuracy: ±0.5% of reading from 10 to 208 V

REAL POWER (WATTS)

Accuracy at 0.1 to 1.5 x
CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading at –1.0 ≤ PF< –0.8

2.2.4 METERING

REACTIVE POWER (VARS)

Accuracy at 0.1 to 1.5 x
CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading at –0.2 ≤ PF ≤ 0.2

APPARENT POWER (VA)

Accuracy at 0.1 to 1.5 x
CT rating and 0.8 to

1.2 x VT rating: ±1.0% of reading

FREQUENCY

Accuracy at

V = 0.8 to 1.2 pu: ±0.01 Hz (when voltage signal is used

for frequency measurement)
I = 0.1 to 0.25 pu: ±0.05 Hz
I > 0.25 pu: ±0.02 Hz (when current signal is used for

frequency measurement)

GE Multilin D30 Line Distance Protection System 2-15

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

2.2.5 INPUTS

AC CURRENT

CT rated primary: 1 to 50000 A
CT rated secondary: 1 A or 5 A by connection
Relay burden: < 0.2 VA at rated secondary
Conversion range:

2

Standard CT: 0.02 to 46 × CT rating RMS symmetrical
Sensitive Ground CT module:

0.002 to 4.6 × CT rating RMS symmetrical

Current withstand: 20 ms at 250 times rated

1 sec. at 100 times rated
continuous 4xInom
Short circuit rating:150000 RMS sym­metrical amperes, 250 V maximum (pri­mary current to external CT)

AC VOLTAGE

VT rated secondary: 50.0 to 240.0 V
VT ratio: 1.00 to 24000.00Relay burden:< 0.25 VA

at 120 V
Conversion range: 1 to 275 V
Voltage withstand: continuous at 260 V to neutral

1 min./hr at 420 V to neutral

FREQUENCY

Nominal frequency setting:25 to 60 Hz
Sampling frequency: 64 samples per power cycle
Tracking frequency range:20 to 70 Hz

CONTACT INPUTS

Dry contacts: 1000 Ω maximum
Wet contacts: 300 V DC maximum
Selectable thresholds: 17 V, 33 V, 84 V, 166 V
Tolerance: ±10%
Contacts per common return: 4
Recognition time: < 1 ms
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Continuous current draw:4 mA (when energized)

CONTACT INPUTS WITH AUTO-BURNISHING

Dry contacts: 1000 Ω maximum
Wet contacts: 300 V DC maximum
Selectable thresholds: 17 V, 33 V, 84 V, 166 V
Tolerance: ±10%
Contacts per common return: 2
Recognition time: < 1 ms
Debounce time: 0.0 to 16.0 ms in steps of 0.5
Continuous current draw:4 mA (when energized)
Auto-burnish impulse current: 50 to 70 mA
Duration of auto-burnish impulse: 25 to 50 ms

DCMA INPUTS

Current input (mA DC): 0 to –1, 0 to +1, –1 to +1, 0 to 5, 0 to 10,

0 to 20, 4 to 20 (programmable)
Input impedance: 379 Ω ±10%
Conversion range: –1 to + 20 mA DC
Accuracy: ±0.2% of full scale
Type: Passive

RTD INPUTS

Types (3-wire): 100 Ω Platinum, 100 & 120 Ω Nickel, 10

Ω Copper

Sensing current: 5 mA
Range: –50 to +250°C
Accuracy: ±2°C
Isolation: 36 V pk-pk

IRIG-B INPUT

Amplitude modulation: 1 to 10 V pk-pk
DC shift: TTL–Compatible
Input impedance: 50 kΩ
Isolation: 2 kV

REMOTE INPUTS (IEC 61850 GSSE/GOOSE)

Input points: 32, configured from 64 incoming bit pairs
Remote devices: 16
Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Remote DPS inputs: 5

DIRECT INPUTS

Input points: 32
Remote devices: 16
Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Ring configuration: Yes, No
Data rate: 64 or 128 kbps
CRC: 32-bit
CRC alarm:

Responding to: Rate of messages failing the CRC
Monitoring message count: 10 to 10000 in steps of 1
Alarm threshold: 1 to 1000 in steps of 1

Unreturned message alarm:

Responding to: Rate of unreturned messages in the ring

configuration

Monitoring message count: 10 to 10000 in steps of 1
Alarm threshold: 1 to 1000 in steps of 1

TELEPROTECTION

Input points: 16
Remote devices: 3
Default states on loss of comms.: On, Off, Latest/Off, Latest/On
Ring configuration: No
Data rate: 64 or 128 kbps
CRC: 32-bit

2.2.6 POWER SUPPLY

LOW RANGE

Nominal DC voltage: 24 to 48 V
Minimum DC voltage: 20 V

Maximum DC voltage: 60 V
Voltage loss hold-up: 20 ms duration at nominal
NOTE: Low range is DC only.

2-16 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

HIGH RANGE

Nominal DC voltage: 125 to 250 V
Minimum DC voltage: 88 V
Maximum DC voltage: 300 V
Nominal AC voltage: 100 to 240 V at 50/60 Hz
Minimum AC voltage: 88 V at 25 to 100 Hz
Maximum AC voltage: 265 V at 25 to 100 Hz
Voltage loss hold-up: 200 ms duration at nominal

FORM-A RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90
Carry continuous: 6 A
Break (DC inductive, L/R = 40 ms):

VOLTAGE CURRENT

24 V 1 A

48 V 0.5 A
125 V 0.3 A
250 V 0.2 A

Operate time: < 4 ms
Contact material: silver alloy

LATCHING RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90
Carry continuous: 6 A as per IEEE C37.90
Break (DC resistive as per IEC61810-1):

VOLTAGE CURRENT

24 V 6 A

48 V 1.6 A
125 V 0.4 A
250 V 0.2 A

Operate time: < 4 ms
Contact material: silver alloy
Control: separate operate and reset inputs
Control mode: operate-dominant or reset-dominant

FORM-A VOLTAGE MONITOR

Applicable voltage: approx. 15 to 250 V DC
Trickle current: approx. 1 to 2.5 mA

ALL RANGES

Volt withstand: 2 × Highest Nominal Voltage for 10 ms
Power consumption: typical = 15 to 20 W/VA

maximum = 50 W/VA
contact factory for exact order code con­sumption

INTERNAL FUSE

RATINGS

Low range power supply: 8 A / 250 V
High range power supply: 4 A / 250 V

INTERRUPTING CAPACITY

AC: 100 000 A RMS symmetrical
DC: 10 000 A

2.2.7 OUTPUTS

FORM-A CURRENT MONITOR

Threshold current: approx. 80 to 100 mA

FORM-C AND CRITICAL FAILURE RELAY

Make and carry for 0.2 s: 30 A as per ANSI C37.90
Carry continuous: 8 A
Break (DC inductive, L/R = 40 ms):

VOLTAGE CURRENT

24 V 1 A

48 V 0.5 A
125 V 0.3 A
250 V 0.2 A

Operate time: < 8 ms
Contact material: silver alloy

FAST FORM-C RELAY

Make and carry: 0.1 A max. (resistive load)
Minimum load impedance:

INPUT

VOLTAGE

250 V DC 20 KΩ 50 KΩ
120 V DC 5 KΩ 2 KΩ

48 V DC 2 KΩ 2 KΩ
24 V DC 2 KΩ 2 KΩ

Note: values for 24 V and 48 V are the same due to a
required 95% voltage drop across the load impedance.

Operate time: < 0.6 ms
Internal Limiting Resistor: 100 Ω, 2 W

2 W RESISTOR 1 W RESISTOR

IMPEDANCE

2

GE Multilin D30 Line Distance Protection System 2-17

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

SOLID-STATE OUTPUT RELAY

Operate and release time: <100 μs
Maximum voltage: 265 V DC
Maximum continuous current: 5 A at 45°C; 4 A at 65°C
Make and carry:

for 0.2 s: 30 A as per ANSI C37.90
for 0.03 s 300 A

Breaking capacity:

2

Operations/
interval

Break
capability
(0 to 250 V
DC)

UL508 Utility

5000 ops /

1s-On, 9s-Off

1000 ops /

0.5 s-On, 0.5 s-Off

3.2 A

L/R = 10 ms

1.6 A

L/R = 20 ms

0.8 A

L/R = 40 ms

application

(autoreclose

scheme)

5ops/

0.2 s-On,

0.2 s-Off
within 1

minute

10 A

L/R = 40 ms

Industrial

application

10000 ops /

0.2 s-On,
30 s-Off

10 A

L/R = 40 ms

CONTROL POWER EXTERNAL OUTPUT
(FOR DRY CONTACT INPUT)

Capacity: 100 mA DC at 48 V DC
Isolation: ±300 Vpk

REMOTE OUTPUTS (IEC 61850 GSSE/GOOSE)

Standard output points: 32
User output points: 32

DIRECT OUTPUTS

Output points: 32

DCMA OUTPUTS

Range: –1 to 1 mA, 0 to 1 mA, 4 to 20 mA
Max. load resistance: 12 kΩ for –1 to 1 mA range

12 kΩ for 0 to 1 mA range
600 Ω for 4 to 20 mA range

Accuracy: ±0.75% of full-scale for 0 to 1 mA range

±0.5% of full-scale for –1 to 1 mA range

±0.75% of full-scale for 0 to 20 mA range
99% Settling time to a step change: 100 ms
Isolation: 1.5 kV
Driving signal: any FlexAnalog quantity
Upper and lower limit for the driving signal: –90 to 90 pu in steps of

0.001

2.2.8 COMMUNICATION PROTOCOLS

RS232

Front port: 19.2 kbps, Modbus RTU

RS485

1 rear port: Up to 115 kbps, Modbus RTU, DNP 3
Typical distance: 1200 m
Isolation: 2 kV, isolated together at 36 Vpk

ETHERNET (FIBER)

PARAMETER FIBER TYPE

100MB MULTI-

MODE

Wavelength 1310 nm
Connector LC
Transmit power –20 dBm
Receiver sensitivity –30 dBm
Power budget 10 dB
Maximum input

power
Typical distance 2 km
Duplex full/half
Redundancy yes

–14 dBm

ETHERNET (10/100 MB TWISTED PAIR)

Modes: 10 MB, 10/100 MB (auto-detect)
Connector: RJ45

SIMPLE NETWORK TIME PROTOCOL (SNTP)

clock synchronization error: <10 ms (typical)

PRECISION TIME PROTOCOL (PTP)

PTP IEEE Std 1588 2008 (version 2)
Power Profile (PP) per IEEE Standard PC37.238TM2011
Slave-only ordinary clock
Peer delay measurement mechanism

OTHER

TFTP, HTTP, IEC 60870-5-104, Ethernet Global Data (EGD)

2-18 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

NOTE

NOTE

NOTE

NOTE

2.2.9 INTER-RELAY COMMUNICATIONS

SHIELDED TWISTED-PAIR INTERFACE OPTIONS

INTERFACE TYPE TYPICAL DISTANCE

RS422 1200 m
G.703 100 m

RS422 distance is based on transmitter power and
does not take into consideration the clock source
provided by the user.

LINK POWER BUDGET

EMITTER,
FIBER TYPE

820 nm LED,
Multimode

1300 nm LED,
Multimode

1300 nm ELED,
Singlemode

1300 nm Laser,
Singlemode

1550 nm Laser,
Singlemode

TRANSMIT

POWER

–20 dBm –30 dBm 10 dB

–21 dBm –30 dBm 9 dB

–23 dBm –32 dBm 9 dB

–1 dBm –30 dBm 29 dB

+5 dBm –30 dBm 35 dB

RECEIVED

SENSITIVITY

POWER

BUDGET

These power budgets are calculated from the manu­facturer’s worst-case transmitter power and worst
case receiver sensitivity.

The power budgets for the 1300 nm ELED are calcu­lated from the manufacturer's transmitter power and
receiver sensitivity at ambient temperature. At
extreme temperatures these values deviate based
on component tolerance. On average, the output
power decreases as the temperature is increased by
a factor 1dB / 5°C.

MAXIMUM OPTICAL INPUT POWER

EMITTER, FIBER TYPE MAX. OPTICAL

820 nm LED, Multimode –7.6 dBm
1300 nm LED, Multimode –11 dBm
1300 nm ELED, Singlemode –14 dBm
1300 nm Laser, Singlemode –14 dBm
1550 nm Laser, Singlemode –14 dBm

INPUT POWER

TYPICAL LINK DISTANCE

EMITTER TYPE CABLE

820 nm LED,
multimode

1300 nm LED,
multimode

1300 nm ELED,
single mode

1300 nm Laser,
single mode

1550 nm Laser,
single-mode

TYPE

62.5/125 μmST 1.65 km
50/125 μmST1.65 km

62.5/125 μmST 4 km
50/125 μmST 4 km
9/125 μm ST 11.4 km

9/125 μm ST 64 km

9/125 μm ST 105 km

CONNECTOR

TYPE

TYPICAL

DISTANCE

Typical distances listed are based on the follow­ing assumptions for system loss. As actual losses
vary from one installation to another, the distance
covered by your system may vary.

CONNECTOR LOSSES (TOTAL OF BOTH ENDS)

ST connector 2 dB

FIBER LOSSES

820 nm multimode 3 dB/km
1300 nm multimode 1 dB/km
1300 nm singlemode 0.35 dB/km
1550 nm singlemode 0.25 dB/km
Splice losses: One splice every 2 km,

at 0.05 dB loss per splice.

SYSTEM MARGIN

3 dB additional loss added to calculations to compensate for
all other losses.

Compensated difference in transmitting and receiving (channel
asymmetry) channel delays using GPS satellite clock: 10 ms

2

2.2.10 ENVIRONMENTAL

AMBIENT TEMPERATURES

Storage temperature: –40 to 85°C
Operating temperature: –40 to 60°C; the LCD contrast can be

impaired at temperatures less than –
20°C

HUMIDITY

Humidity: operating up to 95% (non-condensing) at

55°C (as per IEC60068-2-30 variant 1, 6
days).

OTHER

Altitude: 2000 m (maximum)
Pollution degree: II
Overvoltage category: II
Ingress protection: IP20 front, IP10 back
Noise: 0 dB

GE Multilin D30 Line Distance Protection System 2-19

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

D30 TYPE TESTS

TEST REFERENCE STANDARD TEST LEVEL

Dielectric voltage withstand EN 60255-5 2.2 kV
Impulse voltage withstand EN 60255-5 5 kV

2

Damped oscillatory IEC 61000-4-18 / IEC 60255-22-1 2.5 kV CM, 1 kV DM
Electrostatic discharge EN 61000-4-2 / IEC 60255-22-2 Level 3
RF immunity EN 61000-4-3 / IEC 60255-22-3 Level 3
Fast transient disturbance EN 61000-4-4 / IEC 60255-22-4 Class A and B
Surge immunity EN 61000-4-5 / IEC 60255-22-5 Level 3 and 4
Conducted RF immunity EN 61000-4-6 / IEC 60255-22-6 Level 3
Power frequency immunity EN 61000-4-7 / IEC 60255-22-7 Class A and B
Voltage interruption and ripple DC IEC 60255-11 12% ripple, 200 ms interrupts
Radiated and conducted emissions CISPR11 / CISPR22 / IEC 60255-25 Class A
Sinusoidal vibration IEC 60255-21-1 Class 1
Shock and bump IEC 60255-21-2 Class 1
Seismic IEC 60255-21-3 Class 1
Power magnetic immunity IEC 61000-4-8 Level 5
Pulse magnetic immunity IEC 61000-4-9 Level 4
Damped magnetic immunity IEC 61000-4-10 Level 4
Voltage dip and interruption IEC 61000-4-11 0, 40, 70, 80% dips; 250 / 300 cycle interrupts
Damped oscillatory IEC 61000-4-12 2.5 kV CM, 1 kV DM
Conducted RF immunity, 0 to 150 kHz IEC 61000-4-16 Level 4
Voltage ripple IEC 61000-4-17 15% ripple
Ingress protection IEC 60529 IP40 front, IP10 back
Cold IEC 60068-2-1 –40°C for 16 hours
Hot IEC 60068-2-2 85°C for 16 hours
Humidity IEC 60068-2-30 6 days, variant 1
Damped oscillatory IEEE/ANSI C37.90.1 2.5 kV, 1 MHz
RF immunity IEEE/ANSI C37.90.2 20 V/m, 80 MHz to 1 GHz
Safety UL 508 e83849 NKCR
Safety UL C22.2-14 e83849 NKCR7
Safety UL 1053 e83849 NKCR
Safety IEC 60255-27 Insulation: class 1, Pollution degree: 2, Over

2.2.11 TYPE TESTS

voltage cat II

2.2.12 PRODUCTION TESTS

THERMAL

Products go through an environmental test based upon an

Accepted Quality Level (AQL) sampling process.

2-20 D30 Line Distance Protection System GE Multilin

2 PRODUCT DESCRIPTION 2.2 SPECIFICATIONS

NOTICE

2.2.13 APPROVALS

APPROVALS

COMPLIANCE APPLICABLE

CE Low voltage directive EN 60255-5

C-UL-US --- UL 508

EAC Machines and

COUNCIL DIRECTIVE

EMC directive EN 60255-26 / EN 50263

Equipment

ACCORDING TO

EN 61000-6-5

UL 1053
C22.2 No. 14
TR CU 010/2011

EAC

The EAC Technical Regulations (TR) for Machines and Equipment
apply to the Customs Union (CU) of the Russian Federation,
Belarus, and Kazakhstan.

ITEM DESCRIPTION

Country of origin Puerto Rico or Canada; see label on

Date of manufacture See label on rear of UR
Declaration of Conformity and/or

Certificate of Conformity

rear of UR

Available upon request

2

MOUNTING

Attach mounting brackets using 20 inch-pounds (±2 inch-pounds)
of torque.

2.2.14 MAINTENANCE

CLEANING

Normally, cleaning is not required; but for situations where dust
has accumulated on the faceplate display, a dry cloth can be used.

To avoid deterioration of electrolytic
capacitors, power up units that are stored
in a de-energized state once per year, for
one hour continuously.

GE Multilin D30 Line Distance Protection System 2-21

2

2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION

2-22 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

17.56”

[446,02 mm]

9.687”

[246,05 mm]

11.016”

[279,81 mm]

7.460

[189,48 mm

6.960”
[176,78 mm]

19.040”

[483,62 mm]

6.995”

[177,67 mm]

842807A1.CDR

3 HARDWARE 3.1DESCRIPTION 3.1.1 PANEL CUTOUT

a) HORIZONTAL UNITS

The D30 Line Distance Protection System is available as a 19-inch rack horizontal mount unit with a removable faceplate.
The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains
additional user-programmable pushbuttons and LED indicators.

The modular design allows the relay to be easily upgraded or repaired by a qualified service person. The faceplate is
hinged to allow easy access to the removable modules, and is itself removable to allow mounting on doors with limited rear
depth.

The case dimensions are shown below, along with panel cutout details for panel mounting. When planning the location of
your panel cutout, ensure that provision is made for the faceplate to swing open without interference to or from adjacent
equipment.

The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator
access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws
supplied with the relay.

3

Figure 3–1: D30 HORIZONTAL DIMENSIONS (ENHANCED PANEL)

GE Multilin D30 Line Distance Protection System 3-1

3.1 DESCRIPTION 3 HARDWARE

18.370”

[466,60 mm]

842808A1.CDR

0.280”
[7,11 mm]
Typ. x 4

4.000”

[101,60 mm]

17.750”

[450,85 mm]

CUT-OUT

19.00”

(482.6 mm)

7.00”
(177.8 mm)

Horizontal front view

Horizontal top view (19”, 4 RU)

17.52”

(445.0 mm)

Brackets
repositioned for
switchgear
mounting

10.90”
(276.8 mm)

9.80”

(248.9 mm)

8.97”

(227.8 mm)

17.75”

(450.8 mm)

7.13”

(181.1 mm)

Cutout

18.37”

(466.6 mm)

4.00”
(101.6 mm)

1.57”
(39.8 mm)

4 × 0.28”
(7.1 mm)
diameter

17.72”

(450.1 mm)

14.52”

(368.8 mm)

9.52”

(241.8 mm)

8 × 0.156 Ø

5.00”

(127.0 mm)

0.375”

(9.5 mm)

0.375”
(9.5 mm)

Remote mounting, view from the rear of the panel

Bezel

outline

0.375” (9.5)

1.875”

(47.6)

0.375” (9.5)

4.875”
(121.5 mm)

6.96”
(176.8 mm)

827704B4.CDR

3

Figure 3–2: D30 HORIZONTAL MOUNTING (ENHANCED PANEL)

Figure 3–3: D30 HORIZONTAL MOUNTING AND DIMENSIONS (STANDARD PANEL)

b) VERTICAL UNITS

The D30 Line Distance Protection System is available as a reduced size (¾) vertical mount unit, with a removable face­plate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate con­tains additional user-programmable pushbuttons and LED indicators.

The modular design allows the relay to be easily upgraded or repaired by a qualified service person. The faceplate is
hinged to allow easy access to the removable modules, and is itself removable to allow mounting on doors with limited rear
depth.

The case dimensions are shown below, along with panel cutout details for panel mounting. When planning the location of
your panel cutout, ensure that provision is made for the faceplate to swing open without interference to or from adjacent
equipment.

The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator
access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws
supplied with the relay.

3-2 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

7.48”

(190.0 mm)

15.00”
(381.0 mm)

13.56”
(344.4 mm)

1.38”
(35.2 mm)

9.58”

(243.4 mm)

7.00”

(177.7 mm)

4.00”

(101.6 mm)

7.10”

(180.2 mm)

13.66”
(347.0 mm)

14.03”
(356.2 mm)

0.20”
(5.1 mm)

1.55”
(39.3 mm)

4 Places

0.213” (5.41 mm)

Front of Panel

Mounting Bracket

Vertical Enhanced Front View

Vertical Enhanced Top View

Vertical Enhanced Mounting Panel

CUTOUT

Front of Panel
Reference only

Terminal Blocks

Front
Bezel

Front of Panel

Mounting Bracket

Vertical Enhanced Side View

843809A2.cdr

3

Figure 3–4: D30 VERTICAL DIMENSIONS (ENHANCED PANEL)

GE Multilin D30 Line Distance Protection System 3-3

3

13.72"

(348.5 mm)

7.00"

(177.8 mm)

13.50"

(342.9 mm)

Front of

panel

Front
bezel

Panel

Mounting bracket

1.57”

(39.9 mm)

4.00

(101.6)

7.13”

(181.1 mm)

0.46”
(11.7 mm)

13.65”
(346.7 mm)

14.40”
(365.8 mm)

0.213" (5.4 mm),
4 places

Vertical front view

Vertical side view

843755A4.CDR

Vertical panel mounting

1.85"

(47.0 mm)

9.00"

(228.6 mm)

7.00"

(177.8 mm)

Terminal blocks

Mounting bracket

Panel shown for
reference only

Vertical bottom view

3.1 DESCRIPTION 3 HARDWARE

Figure 3–5: D30 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL)

For side mounting D30 devices with the enhanced front panel, see the following documents available on the UR DVD and
the GE Digital Energy website:

• GEK-113180: UR-Series UR-V Side-Mounting Front Panel Assembly Instructions

• GEK-113181: Connecting a Remote UR-V Enhanced Front Panel to a Vertical UR Device Instruction Sheet

• GEK-113182: Connecting a Remote UR-V Enhanced Front Panel to a Vertically-Mounted Horizontal UR Device
Instruction Sheet

For side mounting D30 devices with the standard front panel, use the following figures.

3-4 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

3

Figure 3–6: D30 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL)

GE Multilin D30 Line Distance Protection System 3-5

3

CUT-OUT

1.33"
(33.9)

2.83"

(71.9)

6.66"

(169.2)

12.20"

(309.9)

0.159" DIA. (6 PLACES)
(4.0)

0.213" DIA. (5.4)
(4 PLACES)
SEE HOLES MARKED 'X'

INCHES

MILLIMETERS

5.33"

(135.4)

PANEL SHOWN FOR
REFERENCE ONLY
(VIEWED FROM FRONT)

'X' 'X'

'X' 'X'

1.00"
(25.4)

1.00"
(25.4)

10.05

(255.3)

"

0.04
(1.0)

"

0.68"

(17.3)

5.27

(133.8)

"

843753A3.cdr

3.1 DESCRIPTION 3 HARDWARE

Figure 3–7: D30 VERTICAL SIDE MOUNTING REAR DIMENSIONS (STANDARD PANEL)

3-6 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.1 DESCRIPTION

XWVUT S PNML KJ H DGF BR

8

4

7

3

6

2

5

1

b

8

4

7

3

6

2

5

1

a

abc abc

abc

Optional

direct

input/output

module

CPU module

(T module shown)

Optional

contact

input/output

module

CT/VT

module

Power
supply

module

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

837811A3.CDR

4

3

2

1

4

3

2

1

b

a

IN

ACT3

LK3

ACT2

LK2

ACT1

LK1

®

®

Model:
Mods:
Wiring Diagram:
Inst. Manual:
Serial Number:
Firmware:
Mfg. Date:
PO Num:
Item Num:

D30D00HCHF8AH6AM6BP8BX7A
000
See manual
1601-0116
MAZB98000029
D
NOV 26, 2012

600001234.56

Control Power:
Contact Inputs:
Contact Outputs:

88-300V DC @ 35W / 77-265V AC @ 35VA
300V DC Max 10mA
Refer to Instruction Manual

RATINGS:

D30

- M A A B 9 7 0 0 0 0 9 9 -

Line Distance Relay

GE Multilin

- M A A B 9 7 0 0 0 0 9 9 -

LISTED

52TL

IND.CONT. EQ.

E83849

WARNING

NOTICE

3.1.2 REAR TERMINAL LAYOUT

3

The relay follows a convention with respect to terminal number assignments which are three characters long assigned in
order by module slot position, row number, and column letter. Two-slot wide modules take their slot designation from the
first slot position (nearest to CPU module) which is indicated by an arrow marker on the terminal block. See the following
figure for an example of rear terminal assignments.

Figure 3–8: REAR TERMINAL VIEW

Do not touch any rear terminals while the relay is energized!

The small form-factor pluggable ports (SFPs) are pluggable transceivers. Do not use non-validated
transceivers or install validated transceivers in the wrong Ethernet slot, else damage can occur.

Figure 3–9: EXAMPLE OF MODULES IN F AND H SLOTS

GE Multilin D30 Line Distance Protection System 3-7

AC or DC

DC

( DC only )

D30

Line Distance
Protection System

Wet

Ground bus

No. 10AWG

minimum

Module arrangement

Optional

JU

MX

L

WKV

H

T

NGS

P

R

Modules must be

grounded if terminal

is provided

BD

F

837810A3.CDR

Dry

Critical failure

48 V DC output

Control power

HI

LO

Power supply

Filter

Surge

B3a

B1b

B8a

B6b

B8b

B6a

B3b

B1a
B2b

B5b

I

V

I

V

M6a

M8a

M5b

M7b

M8b

M5a

M7a

M6c

M8c

M5c

M7c

6A

M1

M2

M3

M4

M1a

M2b

M1c

M1b

M2c

M2a

M4a

M4c

M3b

M3a

M4b

M3c

Contact input/output modules

Contact input M5a

Contact input M7a

Contact input M5c

Contact input M7c

Contact input M6a

Contact input M8a

Contact input M6c

Contact input M8c

Common M5b

Common M7b

Surge

I

V

I

V

H5c

H8a

H7b

H8b

H5a

H7a

H8c

H5b

H7c

6H

H1

H2

H3

H4

H1a

H2b

H1c

H1b

H2c

H2a

H4a

H4c

H3b

H3a

H4b

H3c

Contact input/output modules

Contact input H7a
Contact input H7c
Contact input H8a
Contact input H8c
Common H7b

Surge

H5

H6c

H6a
H6b

H6

I

V

I

V

I

V

I

V

Fibre
optic

Ground at

remote

device

Shielded

twisted pairs

Co-axial cable

COM

D1a
D2a

D4b

D3a

D4a

IRIG-B input

RS485 COM 2

Port 2

Port 1

CPU T

Tx2

Rx2

Tx1

Rx1

BNC

8

CT/VT

6

Inputs/

outputs

6

Inputs/

outputs

1
Power
supply

9

CPU

Typical configuration.
The AC signal path is configurable.

F7c

F4c

F4a
F4b

F7a

F3c

F1c

F5a

F2b

F6c

F2a

F5c
F6a

F2c

F1a
F1b

F3a
F3b

Current inputs

Type 8F/8G CT/VT module

IA

IG

IC

VC

IB

VA

IA5

IG5

IC5

VB

IB5

VA

IA1

IG1

IC1

VC

IB1

VB

F8c

F8a

VX
VX

Voltage inputs

RS232 (front)

DB-9

D30

Computer

1

TXD RXD
RXD TXD

SGND SGND

1

8
3
2

20

7
6
4
5

22

25-pin
connector

9-pin

connector

22
33
44
55
66
77
88
99

Computer

Contacts shown

with no

control power

TC1

Voltage supervision

Voltage and

current supervision

TC2

A

B

C

Tripping
direction

(5 amp)

Current

polarization

source

A

B

C

52

52

Type 8F/8G CT/VT module

100BaseFX

Tx3

Rx3

100BaseFX

100BaseFX

Port 3

OPEN DELTA

VT CONNECTION (ABC)

F8c

F8a

F5a

F5c

F7c

F6a

F7a

F6c

VX

VA

VB

VC

VOLTAGE INPUTS

VX

VA

VB

VC

F5a

F5c

F7c

F6a

F7a

F6c

VA

VB

VC

VOLTAGE INPUTS

VA

VB

VC

3.2 WIRING 3 HARDWARE

3.2WIRING 3.2.1 TYPICAL WIRING

3

3-8 D30 Line Distance Protection System GE Multilin

Figure 3–10: TYPICAL WIRING DIAGRAM (T MODULE SHOWN FOR CPU)

3 HARDWARE 3.2 WIRING

NOTICE

NOTICE

3.2.2 DIELECTRIC STRENGTH

The dielectric strength of the UR-series module hardware is shown in the following table:

Table 3–1: DIELECTRIC STRENGTH OF UR-SERIES MODULE HARDWARE

MODULE

TYPE

1 Power supply High (+); Low (+); (–) Chassis 2000 V AC for 1 minute
1 Power supply 48 V DC (+) and (–) Chassis 2000 V AC for 1 minute
1 Power supply Relay terminals Chassis 2000 V AC for 1 minute
2 Reserved N/A N/A N/A
3 Reserved N/A N/A N/A
4 Reserved N/A N/A N/A
5 Analog inputs/outputs All except 8b Chassis < 50 V DC
6 Digital contact inputs/

7

8 CT/VT All Chassis 2000 V AC for 1 minute
9 CPU All Chassis 2000 V AC for 1 minute

MODULE FUNCTION TERMINALS DIELECTRIC STRENGTH

FROM TO

outputs

G.703 All except 2b, 3a, 7b, 8a Chassis 2000 V AC for 1 minute

RS422 All except 6a, 7b, 8a Chassis < 50 V DC

Filter networks and transient protection clamps are used in the hardware to prevent damage caused
by high peak voltage transients, radio frequency interference (RFI), and electromagnetic interference
(EMI). These protective components can be damaged by application of the ANSI/IEEE C37.90 spec­ified test voltage for a period longer than the specified one minute.

All Chassis 2000 V AC for 1 minute

(AC)

3

3.2.3 CONTROL POWER

Control power supplied to the relay must be connected to the matching power supply range of the
relay. If voltage is applied to the wrong terminals, damage can occur.

The D30 relay, like almost all electronic relays, contains electrolytic capacitors. These capacitors are
well-known to deteriorate over time if voltage is not applied periodically. Deterioration can be avoided
by powering up the relay at least once a year.

The power supply module can be ordered for two possible voltage ranges, and the UR can be ordered with or without a
redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges are
as shown below (see the Technical specifications section of chapter 2 for additional details):

• Low (LO) range: 24 to 48 V (DC only) nominal.

• High (HI) range: 125 to 250 V nominal.
The power supply module provides power to the relay and supplies power for dry contact input connections.
The power supply module provides 48 V DC power for dry contact input connections and a critical failure relay (see the

Typical wiring diagram earlier). The critical failure relay is a form-C device that is energized once control power is applied
and the relay has successfully booted up with no critical self-test failures. If on-going self-test diagnostic checks detect a
critical failure (see the Self-test errors section in chapter 7) or control power is lost, the relay is de-energize.

For high reliability systems, the D30 has a redundant option in which two D30 power supplies are placed in parallel on the
bus. If one of the power supplies become faulted, the second power supply assumes the full load of the relay without any
interruptions. Each power supply has a green LED on the front of the module to indicate it is functional. The critical fail relay
of the module also indicates a faulted power supply.

GE Multilin D30 Line Distance Protection System 3-9

3.2 WIRING 3 HARDWARE

AC or DC

NOTE:
14 gauge stranded
wire with suitable
disconnect devices
is recommended.

Heavy copper conductor

or braided wire

Switchgear

ground bus

UR-series

protection system

FILTER

SURGE

–

+

LOW

+

HIGH

B8b B8a B6a B6b B5b

CONTROL

POWER

827247A1.CDR

NOTICE

An LED on the front of the control power module shows the status of the power supply:

LED INDICATION POWER SUPPLY

CONTINUOUS ON OK
ON / OFF CYCLING Failure
OFF Failure

3

Figure 3–11: CONTROL POWER CONNECTION

3.2.4 CT/VT MODULES

A CT/VT module can have voltage or current inputs on channels 1 through 4 inclusive, or channels 5 through 8 inclusive.
Channels 1 and 5 are intended for connection to phase A, and are labeled as such in the relay. Likewise, channels 2 and 6
are intended for connection to phase B, and channels 3 and 7 are intended for connection to phase C.

Channels 4 and 8 are intended for connection to a single-phase source. For voltage inputs, these channel are labelled as
auxiliary voltage (VX). For current inputs, these channels are intended for connection to a CT between system neutral and
ground, and are labelled as ground current (IG).

Verify that the connection made to the relay terminals for nominal current of 1 A or 5 A matches the
secondary rating of the connected CTs. Unmatched CTs can result in equipment damage or inade-

quate protection.
To connect the module, size 12 American Wire Gauge (AWG) is commonly used; the maximum size is 10 AWG.
CT/VT modules can be ordered with a standard ground current input that is the same as the phase current input. Each AC

current input has an isolating transformer and an automatic shorting mechanism that shorts the input when the module is
withdrawn from the chassis. There are no internal ground connections on the current inputs. Current transformers with 1 to
50000 A primaries and 1 A or 5 A secondaries can be used.

CT/VT modules with a sensitive ground input are also available. The ground CT input of the sensitive ground modules is 10
times more sensitive than the ground CT input of standard CT/VT modules. However, the phase CT inputs and phase VT
inputs are the same as those of regular CT/VT modules.

The above modules have enhanced diagnostics that can automatically detect CT/VT hardware failure and take the relay
out of service.

CT connections for both ABC and ACB phase rotations are identical as shown in the Typical wiring diagram.
The exact placement of a zero-sequence core balance CT to detect ground fault current is shown as follows. Twisted-pair

cabling on the zero-sequence CT is recommended.

3-10 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

Ground connection to neutral
must be on the source side

UNSHIELDED CABLE

LOAD

ABCN G

Ground
outside CT

Source

LOAD

SHIELDED CABLE

996630A6.CDR

ABC

Source

To ground;
must be on
load side

Stress cone

shields

NOTE

~1a

~1b

~1c

~2a

~2b

~2c

~3a

~4a

~5a

~6a

~7a

~8a

~3b

~4b

~5c

~6c

~7c

~8c

~3c

~4c

Current inputs

8F, 8G, 8L, and 8M modules (4 CTs and 4 VTs)

Voltage inputs

VA

VB

VC

VX

VA

VB

VC

VX

IA

IC

IB

IG

IA5

IC5

IB5

IG5

IA1

IC1

IB1

IG1

842768A2.CDR

Figure 3–12: ZERO-SEQUENCE CORE BALANCE CT INSTALLATION

The phase voltage channels are used for most metering and protection purposes. The auxiliary voltage channel is used as
input for the synchrocheck and volts-per-hertz features.

Substitute the tilde “~” symbol with the slot position of the module in the following figure.

3

Figure 3–13: CT/VT MODULE WIRING

3.2.5 PROCESS BUS MODULES

The D30 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin
HardFiber system, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber merging units,
known as Bricks. The HardFiber system has been designed to integrate seamlessly with the existing UR-series applica­tions, including protection functions, FlexLogic, metering, and communications.

The IEC 61850 process bus system offers the following benefits:

• Reduces labor associated with design, installation, and testing of protection and control applications using the D30 by
reducing the number of individual copper terminations

• Integrates seamlessly with existing D30 applications, since the IEC 61850 process bus interface module replaces the
traditional CT/VT modules

• Communicates using open standard IEC 61850 messaging

For additional details on the HardFiber system, see GE publication GEK-113658: HardFiber Process Bus System Instruc­tion Manual.

GE Multilin D30 Line Distance Protection System 3-11

3.2 WIRING 3 HARDWARE

Load

I

~#a

~#b

~#c

V

827862A4.CDR

+

+

+

+

+

a) Voltage with optional
current monitoring

Voltage monitoring only

Load

I

V

Both voltage and current monitoring

Load

I

V

b) Current with optional
voltage monitoring

Current monitoring only Both voltage and current monitoring

(external jumper a-b is required)

Load

V

Load

c) No monitoring

~#a

~#b

~#c

~#a

~#b

~#c

~#a

~#b

~#c

~#a

~#b

~#c

I

3.2.6 CONTACT INPUTS AND OUTPUTS

Every contact input/output module has 24 terminal connections. They are arranged as three terminals per row, with eight
rows in total. A given row of three terminals can be used for the outputs of one relay. For example, for form-C relay outputs,
the terminals connect to the normally open (NO), normally closed (NC), and common contacts of the relay. For a form-A
output, there are options of using current or voltage detection for feature supervision, depending on the module ordered.
The terminal configuration for contact inputs is different for the two applications.

The contact inputs are grouped with a common return. The D30 has two versions of grouping: four inputs per common
return and two inputs per common return. When a contact input/output module is ordered, four inputs per common is used.
If the inputs must be isolated per row, then two inputs per common return should be selected (4D module).

The tables and diagrams on the following pages illustrate the module types (6A, etc.) and contact arrangements that can be
ordered for the relay. Since an entire row is used for a single contact output, the name is assigned using the module slot
position and row number. However, since there are two contact inputs per row, these names are assigned by module slot

3

position, row number, and column position.
Some form-A / solid-state relay outputs include circuits to monitor the DC voltage across the output contact when it is open,

and the DC current through the output contact when it is closed. Each of the monitors contains a level detector whose out­put is set to logic “On = 1” when the current in the circuit is above the threshold setting. The voltage monitor is set to “On =
1” when there is a voltage across open contact (the detector allows a current of about 1 to 2.5 mA), and the current monitor
is set to “On = 1” when the current flowing through the closed contact exceeds about 80 to 100 mA. The voltage monitor is
intended to check the health of the overall trip circuit, and the current monitor can be used to seal-in the output contact until
an external contact has interrupted current flow. If enabled, the current monitoring can be used as a seal-in signal to ensure
that the form-A contact does not attempt to break the energized inductive coil circuit and weld the output contacts.

Block diagrams are shown as follows for form-A and solid-state relay outputs with optional voltage monitor, optional current
monitor, and with no monitoring. The actual values shown for contact output 1 are the same for all contact outputs. Form-A
contact output with or without a current or voltage monitoring option is not polarity sensitive. The polarity shown in the figure
is required for solid-state contact output connection.

Figure 3–14: FORM-A AND SOLID-STATE CONTACT OUTPUTS WITH VOLTAGE AND CURRENT MONITORING

3-12 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

WARNING

NOTE

NOTE

NOTICE

The operation of voltage and current monitors is reflected with the corresponding FlexLogic operands (CONT OP # VON,

CONT OP # VOFF, and CONT OP # ION) which can be used in protection, control, and alarm logic. The typical application of

the voltage monitor is breaker trip circuit integrity monitoring; a typical application of the current monitor is seal-in of the
control command.

Refer to the Digital elements section of chapter 5 for an example of how form-A and solid-state relay contacts can be
applied for breaker trip circuit integrity monitoring.

Consider relay contacts unsafe to touch when the unit is energized.

USE OF FORM-A AND SOLID-STATE RELAY OUTPUTS IN HIGH IMPEDANCE CIRCUITS

For form-A and solid-state relay output contacts internally equipped with a voltage measuring circuit across the con­tact, the circuit has an impedance that can cause a problem when used in conjunction with external high input
impedance monitoring equipment such as modern relay test set trigger circuits. These monitoring circuits may con­tinue to read the form-A contact as being closed after it has closed and subsequently opened, when measured as
an impedance.

The solution is to use the voltage measuring trigger input of the relay test set, and connect the form-A contact
through a voltage-dropping resistor to a DC voltage source. If the 48 V DC output of the power supply is used as a
source, a 500 Ω, 10 W resistor is appropriate. In this configuration, the voltage across either the form-A contact or
the resistor can be used to monitor the state of the output.

Wherever a tilde “~” symbol appears, substitute with the slot position of the module; wherever a number sign “#”
appears, substitute the contact number

3

When current monitoring is used to seal-in the form-A and solid-state relay contact outputs, the Flex­Logic operand driving the contact output should be given a reset delay of 10 ms to prevent damage
of the output contact (in situations when the element initiating the contact output is bouncing, at val­ues in the region of the pickup value).

Table 3–2: CONTACT INPUT AND OUTPUT MODULE ASSIGNMENTS

~6A MODULE ~6B MODULE ~6C MODULE ~6D MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1 Form-A ~1 Form-C ~1a, ~1c 2 Inputs
~2 Form-A ~2 Form-A ~2 Form-C ~2a, ~2c 2 Inputs
~3 Form-C ~3 Form-C ~3 Form-C ~3a, ~3c 2 Inputs

~4 Form-C ~4 Form-C ~4 Form-C ~4a, ~4c 2 Inputs
~5a, ~5c 2 Inputs ~5 Form-C ~5 Form-C ~5a, ~5c 2 Inputs
~6a, ~6c 2 Inputs ~6 Form-C ~6 Form-C ~6a, ~6c 2 Inputs
~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7 Form-C ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8 Form-C ~8a, ~8c 2 Inputs

TERMINAL

ASSIGNMENT

~1Form-C ~1Fast Form-C ~1 Form-A ~1 Form-A

~2Form-C ~2Fast Form-C ~2 Form-A ~2 Form-A

~3Form-C ~3Fast Form-C ~3 Form-A ~3 Form-A

~4Form-C ~4Fast Form-C ~4 Form-A ~4 Form-A
~5a, ~5c 2 Inputs ~5Fast Form-C ~5a,
~6a, ~6c 2 Inputs ~6Fast Form-C ~6a, ~6c 2 Inputs ~6 Form-A
~7a, ~7c 2 Inputs ~7Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

OUTPUT OR

INPUT

~6E MODULE ~6F MODULE ~6G MODULE ~6H MODULE

OUTPUT OR

INPUT

TER MINA L

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT TERMINAL

TERMINAL

ASSIGNMENT

ASSIGNMENT

OUTPUT TERMINAL

OUTPUT OR

INPUT

~5c 2 Inputs ~5 Form-A

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

OUTPUT

INPUT

GE Multilin D30 Line Distance Protection System 3-13

3

3.2 WIRING 3 HARDWARE

~6K MODULE ~6L MODULE ~6M MODULE ~6N MODULE

TERMINAL

ASSIGNMENT

~1 Form-C ~1Form-A ~1Form-A ~1Form-A
~2 Form-C ~2Form-A ~2Form-A ~2Form-A
~3 Form-C ~3Form-C ~3Form-C ~3Form-A
~4 Form-C ~4Form-C ~4Form-C ~4Form-A
~5 Fast Form-C ~5a, ~5c 2 Inputs ~5Form-C ~5a, ~5c 2 Inputs
~6 Fast Form-C ~6a, ~6c 2 Inputs ~6Form-C ~6a, ~6c 2 Inputs
~7 Fast Form-C ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8 Fast Form-C ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

~6P MODULE ~6R MODULE ~6S MODULE ~6T MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1Form-A ~1Form-A ~1Form-A
~2 Form-A ~2Form-A ~2Form-A ~2Form-A
~3 Form-A ~3Form-C ~3Form-C ~3Form-A
~4 Form-A ~4Form-C ~4Form-C ~4Form-A
~5 Form-A ~5a, ~5c 2 Inputs ~5Form-C ~5a, ~5c 2 Inputs
~6 Form-A ~6a, ~6c 2 Inputs ~6Form-C ~6a, ~6c 2 Inputs

~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs

OUTPUT TERMINAL

OUTPUT OR

INPUT

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

TERMINAL

ASSIGNMENT

TERMINAL

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

TER MINA L

ASSIGNMENT

TER MINA L

ASSIGNMENT

OUTPUT OR

INPUT

OUTPUT OR

INPUT

~6U MODULE ~6V MODULE ~67 MODULE ~4A MODULE

TERMINAL

ASSIGNMENT

~1 Form-A ~1 Form-A ~1Form-A ~1Not Used
~2 Form-A ~2 Form-A ~2Form-A ~2 Solid-State
~3 Form-A ~3 Form-C ~3Form-A ~3Not Used
~4 Form-A ~4 2 Outputs ~4Form-A ~4 Solid-State
~5 Form-A ~5a, ~5c 2 Inputs ~5Form-A ~5Not Used
~6 Form-A ~6a, ~6c 2 Inputs ~6Form-A ~6 Solid-State

~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7Form-A ~7Not Used
~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8Form-A ~8 Solid-State

TERMINAL

ASSIGNMENT

~1Not Used ~1 Not Used ~1a, ~1c 2 Inputs ~1 2 Outputs
~2Solid-State ~2 Solid-State ~2a, ~2c 2 Inputs ~2 2 Outputs
~3Not Used ~3 Not Used ~3a, ~3c 2 Inputs ~3 2 Outputs
~4Solid-State ~4 Solid-State ~4a, ~4c 2 Inputs ~4 2 Outputs
~5Not Used ~5 Not Used ~5a, ~5c 2 Inputs ~5 2 Outputs
~6Solid-State ~6 Solid-State ~6a, ~6c 2 Inputs ~6 2 Outputs
~7Not Used ~
~8Solid-State ~8 Solid-State ~8a, ~8c 2 Inputs ~8Not Used

OUTPUT OR

INPUT

~4B MODULE ~4C MODULE ~4D MODULE ~4L MODULE

OUTPUT TERMINAL

TER MINA L

ASSIGNMENT

ASSIGNMENT

7 Not Used ~7a, ~7c 2 Inputs ~72 Outputs

OUTPUT OR

INPUT

OUTPUT TERMINAL

TERMINAL

ASSIGNMENT

ASSIGNMENT

OUTPUT TERMINAL

OUTPUT TERMINAL

ASSIGNMENT

ASSIGNMENT

OUTPUT

OUTPUT

3-14 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

842762A3.CDR

3

Figure 3–15: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2)

GE Multilin D30 Line Distance Protection System 3-15

3

DIGITAL I/O

6K

1b

2b

3b

4b

5b

7b

6b

8b

1a

2a

3a

4a

5a

7a

6a

8a

1c

2c

3c

4c

5c

7c

6c

8c

1

5

7

2

6

8

3

4

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

I

V

I

V

I

V

I

V

I

V

I

V

DIGITAL I/O

6P

1b

2b

3b

4b

5b

6b

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

6c

1

5

2

6

3

4

8a

7b

7a

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

CONTACT IN 7a

CONTACT IN 7c

CONTACT IN 8a

CONTACT IN 8c

COMMON 7b

SURGE

8c

7c

8b

DIGITAL I/O

6U

1b

2b

3b

4b

5b

6b

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

6c

1

5

2

6

3

4

8a

7b

7a

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

CONTACT IN 7a

CONTACT IN 7c

CONTACT IN 8a

CONTACT IN 8c

COMMON 7b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

I

V

I

V

DIGITAL I/O

6M

1b

2b

3b

4b

5b

6b

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

6c

1

5

2

6

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 7c

CONTACT IN 8a

CONTACT IN 8c

COMMON 7b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

DIGITAL I/O

6S

1b

2b

3b

4b

5b

6b

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

6c

1

5

2

6

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 7c

CONTACT IN 8a

CONTACT IN 8c

COMMON 7b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

I

V

I

V

I

V

I

V

DIGITAL I/O

6N

1b

2b

3b

4b

6c

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

5b

1

2

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

DIGITAL I/O

6T

1b

2b

3b

4b

6c

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

5b

1

2

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

I

V

I

V

DIGITAL I/O

6L

1b

2b

3b

4b

6c

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

5b

1

2

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

8c

7c

8b

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

DIGITAL I/O

6R

1b

2b

3b

4b

6c

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

5b

1

2

3

4

8a

7b

7a

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

8c

7c

8b

842763A2.CDR

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

~

DIGITAL I/O

6V

1b

2b

3b

4b

6c

1a

2a

3a

4a

5a

6a

1c

2c

3c

4c

5c

5b

1

2

3

4a

8a

7b

7a

CONTACT IN 7a

CONTACT IN 5a

CONTACT IN 7c

CONTACT IN 5c

CONTACT IN 8a

CONTACT IN 6a

CONTACT IN 8c

CONTACT IN 6c

COMMON 7b

COMMON 5b

SURGE

8c

7c

8b

~

4c

I

V

I

V

NOTICE

3.2 WIRING 3 HARDWARE

3-16 D30 Line Distance Protection System GE Multilin

Figure 3–16: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2)

For proper functionality, observe the polarity shown in the figures for all contact input and output con­nections.

3 HARDWARE 3.2 WIRING

827741A5.CDR

24 to 250 V

(Wet) (Dry)

Contact input 1
Contact input 2
Contact input 3

Surge

Contact input 4

~7a

Common

~7b

~7c
~8a

~8b

~8c

Contact input 1
Contact input 2
Contact input 3

Surge

Contact input 4

~7a

Common

~7b

~7c
~8a

~8b

~8c

Control power

Surge

B5b

Filter

B8b

B6b
B6a
B8a

Critical failure

B1b

48 V DC output

B3b

B1a
B2b
B3a

HI+

LO+

Power supply module

Terminals from type 6B
contact input/output module

Terminals from type 6B
contact input/output module

CONTACT INPUTS

A dry contact has one side connected to terminal B3b. This is the positive 48 V DC voltage rail supplied by the power sup­ply module. The other side of the dry contact is connected to the required contact input terminal. Each contact input group
has its own common (negative) terminal which must be connected to the DC negative terminal (B3a) of the power supply
module. When a dry contact closes, a current of 1 to 3 mA flows through the associated circuit.

A wet contact has one side connected to the positive terminal of an external DC power supply. The other side of this contact
is connected to the required contact input terminal. If a wet contact is used, then the negative side of the external source
must be connected to the relay common (negative) terminal of each contact group. The maximum external source voltage
for this arrangement is 300 V DC.

The voltage threshold at which each group of four contact inputs detects a closed contact input is programmable as
17 V DC for 24 V sources, 33 V DC for 48 V sources, 84 V DC for 110 to 125 V sources, and 166 V DC for 250 V sources.

3

Figure 3–17: DRY AND WET CONTACT INPUT CONNECTIONS

Wherever a tilde “~” symbol appears, substitute with the slot position of the module.

There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recommend
using an external DC supply.

GE Multilin D30 Line Distance Protection System 3-17

3.2 WIRING 3 HARDWARE

842749A1.CDR

50 to 70 mA

3 mA

25 to 50 ms

current

time

CONTACT INPUT 1 AUTO-BURNISH = OFF

= OFFCONTACT INPUT 2 AUTO-BURNISH

CONTACT INPUT 1 AUTO-BURNISH
CONTACT INPUT 2 AUTO-BURNISH

= ON
= OFF

CONTACT INPUT 1 AUTO-BURNISH
CONTACT INPUT 2 AUTO-BURNISH

= OFF
= ON

CONTACT INPUT 1 AUTO-BURNISH
CONTACT INPUT 2 AUTO-BURNISH

= ON
= ON

842751A1.CDR

USE OF CONTACT INPUTS WITH AUTO-BURNISHING

The contact inputs sense a change of the state of the external device contact based on the measured current. When exter­nal devices are located in a harsh industrial environment (either outdoor or indoor), their contacts can be exposed to vari­ous types of contamination. Normally, there is a thin film of insulating sulfidation, oxidation, or contaminates on the surface
of the contacts, sometimes making it difficult or impossible to detect a change of the state. This film must be removed to
establish circuit continuity – an impulse of higher than normal current can accomplish this.

The contact inputs with auto-burnish create a high current impulse when the threshold is reached to burn off this oxidation
layer as a maintenance to the contacts. Afterwards the contact input current is reduced to a steady-state current. The
impulse has a 5 second delay after a contact input changes state.

3

Figure 3–18: CURRENT THROUGH CONTACT INPUTS WITH AUTO-BURNISHING

Regular contact inputs limit current to less than 3 mA to reduce station battery burden. In contrast, contact inputs with auto­burnishing allow currents up to 50 to 70 mA at the first instance when the change of state was sensed. Then, within 25 to
50 ms, this current is slowly reduced to 3 mA as indicated above. The 50 to 70 mA peak current burns any film on the con­tacts, allowing for proper sensing of state changes. If the external device contact is bouncing, the auto-burnishing starts
when external device contact bouncing is over.

Another important difference between the auto-burnishing input module and the regular input modules is that only two con­tact inputs have common ground, as opposed to four contact inputs sharing one common ground (refer to the Contact Input
and Output Module Wiring diagrams). This is beneficial when connecting contact inputs to separate voltage sources. Con­sequently, the threshold voltage setting is also defined per group of two contact inputs.

The auto-burnish feature can be disabled or enabled using the DIP switches found on each daughter card. There is a DIP
switch for each contact, for a total of 16 inputs.

Figure 3–19: AUTO-BURNISH DIP SWITCHES

3-18 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

NOTE

The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the auto­burnish functionality using an oscilloscope.

3

GE Multilin D30 Line Distance Protection System 3-19

3.2 WIRING 3 HARDWARE

NOTE

842764A1.CDR

3.2.7 TRANSDUCER INPUTS/OUTPUTS

Transducer input modules can receive input signals from external DCmA output transducers (DCmA In) or resistance tem­perature detectors (RTDs). Hardware and software are provided to receive signals from these external transducers and
convert these signals into a digital format for use as required.

Transducer output modules provide DC current outputs in several standard DCmA ranges. Software is provided to config­ure virtually any analog quantity used in the relay to drive the analog outputs.

Every transducer input/output module has a total of 24 terminal connections. These connections are arranged as three ter­minals per row with a total of eight rows. A given row can be used for either inputs or outputs, with terminals in column "a"
having positive polarity and terminals in column "c" having negative polarity. Since an entire row is used for a single input/
output channel, the name of the channel is assigned using the module slot position and row number.

Each module also requires that a connection from an external ground bus be made to terminal 8b. The current outputs
require a twisted-pair shielded cable, where the shield is grounded at one end only. The following figure illustrates the trans-

3

ducer module types (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay.

Wherever a tilde “~” symbol appears, substitute with the slot position of the module.

Figure 3–20: TRANSDUCER INPUT/OUTPUT MODULE WIRING

The following figure show how to connect RTDs.

3-20 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

Three-wire shielded cable

RTD terminals

Maximum total lead resistance:
25 ohms for Platinum RTDs

Route cable in separate conduit from
current carrying conductors

RTD

859736A1.CDR

RTD terminals

RTD

RTD

For RTD

RTD

SURGE

~1

~1 &

~2

~2

~8b

~1a

~1b

~2a

Hot

Hot

Return

Comp

Comp

~2c

~1c

3

Figure 3–21: RTD CONNECTIONS

GE Multilin D30 Line Distance Protection System 3-21

3.2 WIRING 3 HARDWARE

NOTE

NOTE

3.2.8 RS232 FACEPLATE PORT

A 9-pin RS232C serial port is located on the D30 faceplate for programming with a computer. All that is required to use this
interface is a computer running the EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is
shown in the following figure for both 9-pin and 25-pin connectors.

The baud rate for this port is fixed at 19200 bps.

3

Figure 3–22: RS232 FACEPLATE PORT CONNECTION

3.2.9 CPU COMMUNICATION PORTS

a) OVERVIEW

In addition to the faceplate RS232 port, the D30 provides a rear RS485 communication port.

The CPU modules do not require a surge ground connection.

3-22 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.2 WIRING

842722A3.CDR

100Base-T

COMMON

+

+

—

—

D1a
D2a
D3a
D4b
D4a

BNC

IRIG-B

input

CPU V

Co-axial cable

Shielded
twisted-pairs

Ground at

remote

device

RS485

COM2

100Base-T

100Base-T

COMMON

+

+

—

—

D1a
D2a
D3a
D4b
D4a

BNC

IRIG-B

input

CPU U

Co-axial cable

Shielded
twisted-pairs

Ground at

remote

device

RS485

COM2

100Base-T

100Base-FX

Port 1

Port 2

100Base-FX

Tx1

Rx1

COMMON

+

+

—

—

D1a
D2a
D3a
D4b
D4a

BNC

IRIG-B

input

CPU T

Co-axial cable

Shielded
twisted-pairs

MM fiber-

optic cable

Ground at

remote

device

RS485

COM2

100Base-FX

100Base-FX

Tx2

Rx2

Tx3

Rx3

Tx1

Rx1

Port 3

Port 1

Port 2

Port 3

Port 1

Port 2

Port 3

100Base-FX

Tx1

Rx1

3

Figure 3–23: CPU MODULE COMMUNICATIONS WIRING

b) RS485 PORTS

RS485 data transmission and reception are accomplished over a single twisted pair with transmit and receive data alternat­ing over the same two wires. Through the use of the port, continuous monitoring and control from a remote computer,
SCADA system, or PLC is possible.

To minimize errors from noise, the use of shielded twisted pair wire is recommended. Correct polarity must also be
observed. For instance, the relays must be connected with all RS485 “+” terminals connected together, and all RS485 “–”
terminals connected together. Though data is transmitted over a two-wire twisted pair, all RS485 devices require a shared
reference, or common voltage. This common voltage is implied to be a power supply common. Some systems allow the
shield (drain wire) to be used as common wire and to connect directly to the D30 COM terminal (#3); others function cor­rectly only if the common wire is connected to the D30 COM terminal, but insulated from the shield.

To avoid loop currents, ground the shield at only one point. If other system considerations require the shield to be grounded
at more than one point, install resistors (typically 100 ohms) between the shield and ground at each grounding point. Each
relay needs to be daisy-chained to the next one in the link. A maximum of 32 relays can be connected in this manner with­out exceeding driver capability. For larger systems, additional serial channels must be added. It is also possible to use com­mercially available repeaters to have more than 32 relays on a single channel. Avoid star or stub connections entirely.

GE Multilin D30 Line Distance Protection System 3-23

3.2 WIRING 3 HARDWARE

SCADA / PLC / computer

Optocoupler

Data

UR-series device

Shield

827757AA.CDR

Last device

Z (*)

T

Z (*) Terminating impedance at

T

each end (typically 120 Ω and 1 nF)

Twisted pair

RS485 +

RS485 –

COMP 485COM

Relay

Relay

Ground shield at SCADA / PLC /

computer only or at

UR-series device only

Data

Optocoupler

Up to 32 devices,

maximum 4000 feet

(1200 m)

Z (*)

T

RS485 +

RS485 –

COMP 485COM

RS485 +
RS485 –

COMP 485COM

COM

NOTE

Lightning strikes and ground surge currents can cause large momentary voltage differences between remote ends of the
communication link. For this reason, surge protection devices are internally provided at both communication ports. An iso­lated power supply with an optocoupled data interface also acts to reduce noise coupling. To ensure maximum reliability, all
equipment should have similar transient protection devices installed.

Terminate both ends of the RS485 circuit with an impedance as shown below.

3

c) 100BASE-FX FIBER OPTIC PORTS

Ensure that the dust covers are installed when the fiber is not in use. Dirty or scratched connectors can lead to high

The fiber optic communication ports allow for fast and efficient communications between relays at 100 Mbps. Optical fiber

losses on a fiber link.

can be connected to the relay supporting a wavelength of 1310 nm in multi-mode.

3-24 D30 Line Distance Protection System GE Multilin

Figure 3–24: RS485 SERIAL CONNECTION

3 HARDWARE 3.2 WIRING

UR-series device

BNC (in)

Receiver

RG58/59 coaxial cable

GPS satellite system

GPS connection

IRIG-B (–)

4A

+

827756A8.CDR

IRIG-B
time code generator

(DC-shift or
amplitude modulated
signal can be used)

4B

IRIG-B (+)

UR-series device

BNC (in)

Receiver

Twisted-pair cable

GPS satellite system

GPS connection

IRIG-B (–)

4A

+

IRIG-B
time code generator

(DC-shift or
amplitude modulated
signal can be used)

4B

IRIG-B (+)

NOTE

3.2.10 IRIG-B

IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The
IRIG-B code allows time accuracies of up to 100 ns. Using the IRIG-B input, the D30 operates an internal oscillator with 1
µs resolution and accuracy. The IRIG time code formats are serial, width-modulated codes that can be either DC level
shifted or amplitude modulated (AM). Third party equipment is available for generating the IRIG-B signal; this equipment
can use a GPS satellite system to obtain the time reference so that devices at different geographic locations can be syn­chronized.

3

Figure 3–25: OPTIONS FOR THE IRIG-B CONNECTION

Using an amplitude modulated receiver causes errors up to 1 ms in event time-stamping.

GE Multilin D30 Line Distance Protection System 3-25

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842006A2.CDR

Tx

Tx

Tx

Tx

UR 1

UR 2

UR 3

UR 4

Rx

Rx

Rx

Rx

842007A3.CDR

Tx1

UR 1

Tx2

Rx1

Rx2

Tx1

UR 2

Tx2

Rx1

Rx2

Tx1

UR 3

Tx2

Rx1

Rx2

Tx1

UR 4

Tx2

Rx1

Rx2

3.3DIRECT INPUT/OUTPUT COMMUNICATIONS 3.3.1 DESCRIPTION

The direct inputs and outputs feature makes use of the type 7 series of communications modules, which allow direct mes­saging between UR devices. These communications modules are outlined in the table later in this section.

The communications channels are normally connected in a ring configuration as shown in the following figure. The trans­mitter of one module is connected to the receiver of the next module. The transmitter of this second module is then con­nected to the receiver of the next module in the ring. This is continued to form a communications ring. The figure illustrates
a ring of four UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to UR4-Rx,
and UR4-Tx to UR1-Rx. A maximum of 16 UR-series relays can be connected in a single ring

3

Figure 3–26: DIRECT INPUT AND OUTPUT SINGLE CHANNEL CONNECTION

The interconnection for dual-channel type 7 communications modules is shown as follows. Two channel modules allow for
a redundant ring configuration. That is, two rings can be created to provide an additional independent data path. The
required connections are: UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1
for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the
second ring.

The following diagram shows the connection for three UR-series relays using two independent communication channels.
UR1 and UR3 have single type 7 communication modules; UR2 has a dual-channel module. The two communication chan­nels can be of different types, depending on the type 7 modules used. To allow the direct input and output data to cross-
over from channel 1 to channel 2 on UR2, the
forces UR2 to forward messages received on Rx1 out Tx2, and messages received on Rx2 out Tx1.

3-26 D30 Line Distance Protection System GE Multilin

Figure 3–27: DIRECT INPUT AND OUTPUT DUAL CHANNEL CONNECTION

DIRECT I/O CHANNEL CROSSOVER setting should be “Enabled” on UR2. This

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

842013A2.CDR

Channel 1

Channel 2

Tx1

UR 2

Tx2

Rx1

Rx2

Tx

UR 1

Rx

Tx

UR 3

Rx

NOTE

Figure 3–28: DIRECT INPUT AND OUTPUT SINGLE/DUAL CHANNEL COMBINATION CONNECTION

The interconnection requirements are described in further detail in this section for each specific variation of type 7 commu­nications module. These modules are listed in the following table. All fiber modules use ST type connectors.

Not all the direct input and output communications modules outlined in the table are applicable to the D30. Use your
order code with the tables in chapter 2 to determine applicable options.

3

Table 3–3: CHANNEL COMMUNICATION OPTIONS (Sheet 1 of 2)

MODULE SPECIFICATION

2A C37.94SM, 1300 nm, single-mode, ELED, 1 channel single-mode
2B C37.94SM, 1300 nm, single-mode, ELED, 2 channel single-mode
2E Bi-phase, 1 channel
2F Bi-phase, 2 channel
2G IEEE C37.94, 820 nm, 128 kbps, multi-mode, LED, 1 channel
2H IEEE C37.94, 820 nm, 128 kbps, multi-mode, LED, 2 channels
72 1550 nm, single-mode, laser, 1 channel
73 1550 nm, single-mode, laser, 2 channels
74 Channel 1 - RS422; channel 2 - 1550 nm, single-mode, laser
75 Channel 1 - G.703; channel 2 - 1550 nm, single-mode, laser
76 IEEE C37.94, 820 nm, 64 kbps, multi-mode, LED, 1 channel
77 IEEE C37.94, 820 nm, 64 kbps, multi-mode, LED, 2 channels
7A 820 nm, multi-mode, LED, 1 channel
7B 1300 nm, multi-mode, LED, 1 channel
7C 1300 nm, single-mode, ELED, 1 channel
7D 1300 nm, single-mode, laser, 1 channel
7E Channel 1: G.703, Channel 2: 820 nm, multi-mode
7F Channel 1: G.703, Channel 2: 1300 nm, multi-mode
7G Channel 1: G.703, Channel 2: 1300 nm, single-mode ELED
7H 820 nm, multi-mode, LED, 2 channels
7I 1300 nm, multi-mode, LED, 2 channels
7J 1300 nm, single-mode, ELED, 2 channels
7K 1300 nm, single-mode, LASER, 2 channels
7L Channel 1: RS422, channel: 820 nm, multi-mode, LED
7M Channel 1: RS422, channel 2: 1300 nm, multi-mode, LED
7N Channel 1: RS422, channel 2: 1300 nm, single-mode, ELED
7P Channel 1: RS422, channel 2: 1300 nm, single-mode, laser

GE Multilin D30 Line Distance Protection System 3-27

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

7A, 7B, and

7C modules

7H, 7I, and

7J modules

1 channel 2 channels

Rx1

Rx1

Rx2

Tx1 Tx1

Tx2

831719A3.CDR

1 channel 2 channels

Rx1 Rx1

Rx2

Tx1 Tx1

Tx2

831720A5.CDR

72 and 7D

modules

73 and 7K

modules

Table 3–3: CHANNEL COMMUNICATION OPTIONS (Sheet 2 of 2)

MODULE SPECIFICATION

7Q Channel 1: G.703, channel 2: 1300 nm, single-mode, laser
7R G.703, 1 channel
7S G.703, 2 channels
7T RS422, 1 channel
7V RS422, 2 channels, 2 clock inputs
7W RS422, 2 channels

3.3.2 FIBER: LED AND ELED TRANSMITTERS

The following figure shows the configuration for the 7A, 7B, 7C, 7H, 7I, and 7J fiber-only modules.

3

Figure 3–29: LED AND ELED FIBER MODULES

3.3.3 FIBER-LASER TRANSMITTERS

The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser module.

Figure 3–30: LASER FIBER MODULES

3-28 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

CAUTION

NOTICE

Observing any fiber transmitter output can injure the eye.

When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the
maximum optical input power to the receiver.

3

GE Multilin D30 Line Distance Protection System 3-29

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

NOTE

842773A3.CDR

~8a
~8b

7S

Rx +

Tx +

Shield
Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

~2b

~6a

~7a

~1b

~1a

~3a

~6b

~7b

~2a

~3b

G.703
channel 2

G.703
channel 1

Surge

Surge

X8a
X8b

7S

Rx +

Tx +

Shield
Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

X2b

X6a

X7a

X1b

X1a

X3a

X6b

X7b

X2a

X3b

G.703
channel 2

G.703
channel 1

Surge

Surge

831727A5.CDR

X8a
X8b

7S

Rx +

Tx +

Shield
Tx –

Shield

Rx –

Tx –

Rx +

Tx +

Rx –

G.703 communications

X2b

X6a

X7a

X1b

X1a

X3a

X6b

X7b

X2a

X3b

G.703
channel 2

G.703
channel 1

Surge

Surge

NOTE

3.3.4 G.703 INTERFACE

a) DESCRIPTION

The following figure shows the 64K ITU G.703 co-directional interface configuration.

The G.703 module is fixed at 64 kbps. The SETTINGS > PRODUCT SETUP > DIRECT I/O > DIRECT I/O DATA
RATE setting is not applicable to this module.

AWG 24 twisted shielded pair is recommended for external connections, with the shield grounded only at one end. Con­necting the shield to pin X1a or X6a grounds the shield since these pins are internally connected to ground. Thus, if pin X1a
or X6a is used to ground the shield at one end, do not ground the shield at the other end. This interface module is protected
by surge suppression devices.

3

The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical arrange­ment of these pins, see the Rear terminal assignments section earlier in this chapter. All pin interconnections are to be
maintained for a connection to a multiplexer.

b) G.703 SELECTION SWITCH PROCEDURES

1. With the power to the relay off, remove the G.703 module (7R or 7S) as follows. Record the original location of the

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes.

6. Replace the top cover and the cover screw.

3-30 D30 Line Distance Protection System GE Multilin

Figure 3–31: G.703 INTERFACE CONFIGURATION

Figure 3–32: TYPICAL PIN INTERCONNECTION BETWEEN TWO G.703 INTERFACES

Pin nomenclature can differ from one manufacturer to another. Therefore, it is not uncommon to see pinouts num­bered TxA, TxB, RxA and RxB. In such cases, it can be assumed that “A” is equivalent to “+” and “B” is equivalent
to “–”.

module to help ensure that the same or replacement module is inserted into the correct slot.

module for removal.

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

7. Re-insert the G.703 module. Take care to ensure that the correct module type is inserted into the correct slot position.
The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged position as
the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis, engage the
clips simultaneously. When the clips have locked into position, the module is fully inserted.

3

Figure 3–33: G.703 TIMING SELECTION SWITCH SETTING

Table 3–4: G.703 TIMING SELECTIONS

SWITCHES FUNCTION

S1 OFF → octet timing disabled

S5 and S6 S5 = OFF and S6 = OFF → loop timing mode

ON → octet timing 8 kHz

S5 = ON and S6 = OFF → internal timing mode
S5 = OFF and S6 = ON → minimum remote loopback mode
S5 = ON and S6 = ON → dual loopback mode

c) G.703 OCTET TIMING

If octet timing is enabled (ON), this 8 kHz signal is asserted during the violation of bit 8 (LSB) necessary for connecting to
higher order systems. When D30s are connected back-to-back, octet timing is disabled (OFF).

d) G.703 TIMING MODES

There are two timing modes for the G.703 module: internal timing mode and loop timing mode (default).

• Internal Timing Mode: The system clock is generated internally. Therefore, the G.703 timing selection should be in
the internal timing mode for back-to-back (UR-to-UR) connections. For back-to-back connections, set for octet timing
(S1 = OFF) and timing mode to internal timing (S5 = ON and S6 = OFF).

• Loop Timing Mode: The system clock is derived from the received line signal. Therefore, the G.703 timing selection
should be in loop timing mode for connections to higher order systems. For connection to a higher order system (UR­to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 =
OFF).

GE Multilin D30 Line Distance Protection System 3-31

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

842752A2.CDR

Internal timing mode

Loop timing mode

(factory default)

DMR

DMX

G7X

G7R

DMR = Differential Manchester Receiver
DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver

842774A1.CDR

DMR

DMX

G7X

G7R

DMR = Differential Manchester Receiver
DMX = Differential Manchester Transmitter
G7X = G.703 Transmitter
G7R = G.703 Receiver

842775A1.CDR

The switch settings for the internal and loop timing modes are shown below:

e) G.703 TEST MODES

3

In minimum remote loopback mode, the multiplexer is enabled to return the data from the external interface without any
processing to assist in diagnosing G.703 line-side problems irrespective of clock rate. Data enters from the G.703 inputs,
passes through the data stabilization latch which also restores the proper signal polarity, passes through the multiplexer
and then returns to the transmitter. The differential received data is processed and passed to the G.703 transmitter module
after which point the data is discarded. The G.703 receiver module is fully functional and continues to process data and
passes it to the differential Manchester transmitter module. Since timing is returned as it is received, the timing source is
expected to be from the G.703 line side of the interface.

In dual loopback mode, the multiplexers are active and the functions of the circuit are divided into two with each receiver/
transmitter pair linked together to deconstruct and then reconstruct their respective signals. Differential Manchester data
enters the Differential Manchester receiver module and then is returned to the differential Manchester transmitter module.
Likewise, G.703 data enters the G.703 receiver module and is passed through to the G.703 transmitter module to be
returned as G.703 data. Because of the complete split in the communications path and because, in each case, the clocks
are extracted and reconstructed with the outgoing data, in this mode there must be two independent sources of timing. One
source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface.

Figure 3–34: G.703 MINIMUM REMOTE LOOPBACK MODE

Figure 3–35: G.703 DUAL LOOPBACK MODE

3-32 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

~

~

~

~

~

~

~

~

~

~

~

~

~

~

Shield

Shield

COM

Tx +

Tx +

Tx –

Tx –

Rx –

Rx –

Rx +

Rx +

3b

5b

2a

4a

6a

7b

8b

Clock

RS422

channel 1

RS422

channel 2

Surge

3a

5a

4b

6b

7a

2b
8a

Inter-relay communications 7W

842776A3.CDR

Dual-channel RS422 module

~

~

~

~

~

Shield

Tx +

Tx –

Rx –

Rx +

3b

2a

6a

RS422

3a

4b

~

~

~

~

COM

8b

Clock

Surge

7a

2b
8a

Inter-relay comms. 7T

Single-channel RS422 module

~ indicates the slot position

831728A5.CDR

W8a

7T

Shield

Tx –
Rx –
Tx +
Rx +

RS422 communications

W4b

W3a

W3b

W6a

W2a

RS422
channel 1

Surge

+
–

W7a
W8b

Clock

Common

W2b

COM

W8a

7T

Shield

Tx –
Rx –
Tx +
Rx +

RS422 communications

W4b

W3a

W3b

W6a

W2a

RS422
channel 1

Surge

+

–

W7a
W8b

Clock

Common

W2b

COM

+

–

64 or 128 kbps

3.3.5 RS422 INTERFACE

a) DESCRIPTION

There are two RS422 inter-relay communications modules available: single-channel RS422 (module 7T) and dual-channel
RS422 (module 7W). The modules can be configured to run at 64 kbps or 128 kbps. AWG 20-24 twisted shielded pair cable
is recommended for external connections. These modules are protected by optically-isolated surge suppression devices.

The shield pins (6a and 7b) are internally connected to the ground pin (8a). Proper shield termination is as follows:

• Site 1: Terminate shield to pins 6a or 7b or both.

• Site 2: Terminate shield to COM pin 2b.

Match the clock terminating impedance with the impedance of the line.

3

The following figure shows the typical pin interconnection between two single-channel RS422 interfaces installed in slot W.
All pin interconnections are to be maintained for a connection to a multiplexer.

b) TWO-CHANNEL APPLICATION VIA MULTIPLEXERS

The RS422 interface can be used for single channel or two channel applications over SONET/SDH or multiplexed systems.
When used in single-channel applications, the RS422 interface links to higher order systems in a typical fashion observing
transmit (Tx), receive (Rx), and send timing (ST) connections. However, when used in two-channel applications, certain cri­teria must be followed since there is one clock input for the two RS422 channels. The system functions correctly when the
following connections are observed and your data module has a terminal timing feature. Terminal timing is a common fea­ture to most synchronous data units that allows the module to accept timing from an external source. Using the terminal
timing feature, two channel applications can be achieved if these connections are followed: The send timing outputs from
the multiplexer (data module 1), connects to the clock inputs of the UR–RS422 interface in the usual fashion. In addition,
the send timing outputs of data module 1 is also paralleled to the terminal timing inputs of data module 2. By using this con­figuration, the timing for both data modules and both UR–RS422 channels are derived from a single clock source. As a
result, data sampling for both of the UR–RS422 channels is synchronized via the send timing leads on data module 1 as
shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a
viable option that does not impose timing restrictions.

GE Multilin D30 Line Distance Protection System 3-33

Figure 3–36: RS422 INTERFACE CONNECTIONS

Figure 3–37: TYPICAL PIN INTERCONNECTION BETWEEN TWO RS422 INTERFACES

3

Data module 1

Data module 2

Signal name

Signal name

SD(A) - Send data

TT(A) - Terminal timing

TT(B) - Terminal timing

SD(B) - Send data

RD(A) - Received data

RD(A) - Received data

SD(A) - Send data

SD(B) - Send data

RD(B) - Received data

RD(B) - Received data

RS(A) - Request to send (RTS)

RS(A) - Request to send (RTS)

RT(A) - Receive timing

CS(A) - Clear To send

CS(A) - Clear To send

RT(B) - Receive timing

CS(B) - Clear To send

CS(B) - Clear To send

Local loopback

Local loopback

Remote loopback

Remote loopback

Signal ground

Signal ground

ST(A) - Send timing

ST(A) - Send timing

ST(B) - Send timing

ST(B) - Send timing

RS(B) - Request to send (RTS)

RS(B) - Request to send (RTS)

831022A3.CDR

W

7a

W

2b

W

8a

7W

Shld.

Shld.

Tx1(+)

Tx2(+)

Tx1(-)

Tx2(-)

Rx1(+)

Rx2(+)

+

com

Rx1(-)

Rx2(-)

–

INTER-RELAY COMMUNICATIONS

W

3a

W

5b

W

5a

W

3b

W

2a

W

6a

W

6b

W

7b

W

8b

W

4b

W

4a

RS422

CHANNEL 1

RS422

CHANNEL 2

CLOCK

SURGE

Tx Clock

Tx Data

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Figure 3–38: TIMING CONFIGURATION FOR RS422 TWO-CHANNEL, 3-TERMINAL APPLICATION

Data module 1 provides timing to the D30 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides
timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been
omitted in the figure above since they vary by manufacturer.

c) TRANSMIT TIMING

The RS422 interface accepts one clock input for transmit timing. It is important that the rising edge of the 64 kHz transmit
timing clock of the multiplexer interface is sampling the data in the center of the transmit data window. Therefore, it is impor­tant to confirm clock and data transitions to ensure proper system operation. For example, the following figure shows the
positive edge of the Tx clock in the center of the Tx data bit.

d) RECEIVE TIMING

The RS422 interface utilizes NRZI-MARK modulation code and; therefore, does not rely on an Rx clock to recapture data.
NRZI-MARK is an edge-type, invertible, self-clocking code.

3-34 D30 Line Distance Protection System GE Multilin

Figure 3–39: CLOCK AND DATA TRANSITIONS

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

NOTICE

Tx2

Rx2

842777A2.CDR

~8a

7L, 7M, 7N,

7P, and 74

Shield

Tx –
Rx –
Tx +
Rx +

RS422

communications

~4b

~3a

~3b

~6a

~2a

RS422
channel 1

Surge

+
–

~7a
~8b

Clock
channel 1

Common

~2b

COM

Fiber
channel 2

NOTICE

Rx2

Tx2

842778A2.CDR

~3b

75, 7E, 7F, 7G,

and 7Q

Rx +

Shield
Tx –
Rx –
Tx +

G.703

communications

~2b

~1b

~1a

~3a

~2a

G.703
channel 1

Surge

Fiber
channel 2

To recover the Rx clock from the data-stream, an integrated DPLL (digital phase lock loop) circuit is utilized. The DPLL is
driven by an internal clock, which is 16-times over-sampled, and uses this clock along with the data-stream to generate a
data clock that can be used as the SCC (serial communication controller) receive clock.

3.3.6 RS422 AND FIBER INTERFACE

The following figure shows the combined RS422 plus fiberoptic interface configuration at 64K baud. The 7L, 7M, 7N, 7P,
and 74 modules are used in two-terminal with a redundant channel or three-terminal configurations where channel 1 is
employed via the RS422 interface (possibly with a multiplexer) and channel 2 via direct fiber.

AWG 20-24 twisted shielded pair is recommended for external RS422 connections and ground the shield only at one end.
For the direct fiber channel, address power budget issues properly.

When using a LASER Interface, attenuators can be necessary to ensure that you do not exceed
maximum optical input power to the receiver.

3

Figure 3–40: RS422 AND FIBER INTERFACE CONNECTION

Connections shown above are for multiplexers configured as DCE (data communications equipment) units.

3.3.7 G.703 AND FIBER INTERFACE

The figure below shows the combined G.703 plus fiberoptic interface configuration at 64 kbps. The 7E, 7F, 7G, 7Q, and 75
modules are used in configurations where channel 1 is employed via the G.703 interface (possibly with a multiplexer) and
channel 2 via direct fiber. AWG 24 twisted shielded pair is recommended for external G.703 connections connecting the
shield to pin 1a at one end only. For the direct fiber channel, address power budget issues properly. See previous sections
for additional details on the G.703 and fiber interfaces.

When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the
maximum optical input power to the receiver.

Figure 3–41: G.703 AND FIBER INTERFACE CONNECTION

GE Multilin D30 Line Distance Protection System 3-35

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

UR-series

device

IEEE C37.94
fiber interface

up to 2 km

842755A2.CDR

Digital
multiplexer,
IEEE C37.94

compliant

UR-series

device

up to 2 km

IEEE C37.94

converter

RS422

interface

842756A2.CDR

IEEE C37.94

fiber interface

Digital

multiplexer

with EIA-422

interface

3.3.8 IEEE C37.94 INTERFACE

The UR-series IEEE C37.94 communication modules (modules types 76, and 77) are designed to interface with IEEE
C37.94 compliant digital multiplexers or an IEEE C37.94 compliant interface converter for use with direct input and output
applications. The IEEE C37.94 standard defines a point-to-point optical link for synchronous data between a multiplexer
and a teleprotection device. This data is typically 64 kbps, but the standard provides for speeds up to 64n kbps, where n =
1, 2,…, 12. The UR-series C37.94 communication modules are either 64 kbps (with n fixed at 1) for 128 kbps (with n fixed
at 2). The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from the stand­point of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit rate of
2048 kbps.

The specifications for the module are as follows:.

• IEEE standard: C37.94 for 2 × 64 kbps optical fiber interface (for 76 and 77 modules)

• Fiber optic cable type: 50 nm or 62.5 µm core diameter optical fiber

3

• Fiber optic mode: multi-mode

• Fiber optic cable length: up to 2 km

• Fiber optic connector: type ST

• Wavelength: 820 ±40 nm

• Connection: as per all fiber optic connections, a Tx to Rx connection is required
The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports

the IEEE C37.94 standard as shown below.

The UR-series C37.94 communication module can be connected to the electrical interface (G.703, RS422, or X.21) of a
non-compliant digital multiplexer via an optical-to-electrical interface converter that supports the IEEE C37.94 standard, as
shown below.

In 2008, GE Digital Energy released revised modules 76 and 77 for C37.94 communication to enable multi-ended fault
location functionality with firmware 5.60 release and higher. All modules 76 and 77 shipped since the change support this
feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60
and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of D30 communi­cation for two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For
customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed.

3-36 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

842753A2.CDR

Internal timing mode

Loop timing mode

(factory default)

The UR-series C37.94 communication module has six switches that are used to set the clock configuration. The functions
of these control switches are shown below.

For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be
internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.

For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection
should be in loop timing mode for connections to higher order systems.

The IEEE C37.94 communications module cover removal procedure is as follows:

1. With power to the relay off, remove the IEEE C37.94 module (type 76 or 77 module) as follows. Record the original
location of the module to help ensure that the same or replacement module is inserted into the correct slot.

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the
module for removal.

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).

6. Replace the top cover and the cover screw.

7. Re-insert the IEEE C37.94 module. Take care to ensure that the correct module type is inserted into the correct slot
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged posi­tion as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

3

GE Multilin D30 Line Distance Protection System 3-37

3

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Figure 3–42: IEEE C37.94 TIMING SELECTION SWITCH SETTING

3-38 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

CH1 Link/Activity LED

CH2 Link/Activity LED

COMMS

2B

C37.94SM
1300nm single-mode
ELED
2 channel

Technical support:
Tel: [phone]
Fax: [phone]

(NORTH AMERICA)

1 800 547-8629

Made in Canada

GE Multilin

REV. D

CH1 Clock Configuration LED
CH2 Clock Configuration LED

FRONT VIEW REAR VIEW

842837A1.cdr

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the follow­ing figure.

3

Figure 3–43: STATUS LEDS

The clock configuration LED status is as follows:

• Flashing green — loop timing mode while receiving a valid data packet

• Flashing yellow — internal mode while receiving a valid data packet

• Solid red — (switch to) internal timing mode while not receiving a valid data packet

The link/activity LED status is as follows:

• Flashing green — FPGA is receiving a valid data packet

• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"

• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

GE Multilin D30 Line Distance Protection System 3-39

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

UR-series

device

C37.94SM

fiber interface

up to 10 km

842757A2.CDR

Digital

multiplexer

C97.94SM

UR-series

device with

C37.94SM

module

C37.94SM

fiber interface

up to 10 km

UR-series

device with

C37.94SM

module

842758A2.CDR

3.3.9 C37.94SM INTERFACE

The UR-series C37.94SM communication modules (2A and 2B) are designed to interface with modified IEEE C37.94 com­pliant digital multiplexers or IEEE C37.94 compliant interface converters that have been converted from 820 nm multi-mode
fiber optics to 1300 nm ELED single-mode fiber optics. The IEEE C37.94 standard defines a point-to-point optical link for
synchronous data between a multiplexer and a teleprotection device. This data is typically 64 kbps, but the standard pro­vides for speeds up to 64n kbps, where n = 1, 2,…, 12. The UR-series C37.94SM communication module is 64 kbps only
with n fixed at 1. The frame is a valid International Telecommunications Union (ITU-T) recommended G.704 pattern from
the standpoint of framing and data rate. The frame is 256 bits and is repeated at a frame rate of 8000 Hz, with a resultant bit
rate of 2048 kbps.

The specifications for the module are as follows:

• Emulated IEEE standard: emulates C37.94 for 1 × 64 kbps optical fiber interface (modules set to n = 1 or 64 kbps)

• Fiber optic cable type: 9/125 μm core diameter optical fiber

3

• Fiber optic mode: single-mode, ELED compatible with HP HFBR-1315T transmitter and HP HFBR-2316T receiver

• Fiber optic cable length: up to 11.4 km

• Fiber optic connector: type ST

• Wavelength: 1300 ±40 nm

• Connection: as per all fiber optic connections, a Tx to Rx connection is required
The UR-series C37.94SM communication module can be connected directly to any compliant digital multiplexer that sup-

ports C37.94SM as shown below.

It can also can be connected directly to any other UR-series relay with a C37.94SM module as shown below.

In 2008, GE Digital Energy released revised modules 2A and 2B for C37.94SM communication to enable multi-ended fault
location functionality with firmware 5.60 release and higher. All modules 2A and 2B shipped since the change support this
feature and are fully backward compatible with firmware releases below 5.60. For customers using firmware release 5.60
and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of D30 communi­cation for two and three terminal applications. Failure to use it at all ends results in intermittent communication alarms. For
customers using firmware revisions below 5.60, it is not required to match the revision of the modules installed.

3-40 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

842753A2.CDR

Internal timing mode

Loop timing mode

(factory default)

The UR-series C37.94SM communication module has six switches that are used to set the clock configuration. The func­tions of these control switches are shown below.

For the internal timing mode, the system clock is generated internally. Therefore, the timing switch selection should be
internal timing for relay 1 and loop timed for relay 2. There must be only one timing source configured.

For the looped timing mode, the system clock is derived from the received line signal. Therefore, the timing selection
should be in loop timing mode for connections to higher order systems.

The C37.94SM communications module cover removal procedure is as follows:

1. With power to the relay off, remove the C37.94SM module (modules 2A or 2B) as follows. Record the original location
of the module to help ensure that the same or replacement module is inserted into the correct slot.

2. Simultaneously pull the ejector/inserter clips located at the top and at the bottom of each module in order to release the
module for removal.

3. Remove the module cover screw.

4. Remove the top cover by sliding it towards the rear and then lift it upwards.

5. Set the timing selection switches (channel 1, channel 2) to the desired timing modes (see description above).

6. Replace the top cover and the cover screw.

7. Re-insert the C37.94SM module. Take care to ensure that the correct module type is inserted into the correct slot
position. The ejector/inserter clips located at the top and at the bottom of each module must be in the disengaged posi­tion as the module is smoothly inserted into the slot. Once the clips have cleared the raised edge of the chassis,
engage the clips simultaneously. When the clips have locked into position, the module is fully inserted.

3

GE Multilin D30 Line Distance Protection System 3-41

3

Cover screw

Top cover

Bottom cover

Ejector/inserter clip

Ejector/inserter clip

Timing selection

switches

Channel 1

Channel 2

FRONT

REAR

831774A3.CDR

Tx1

Tx2

Rx1

Rx2

Tx1

Tx2

CH1 Link/Activity LED

CH2 Link/Activity LED

COMMS

2B

C37.94SM
1300nm single-mode
ELED
2 channel

Technical support:
Tel: [phone]
Fax: [phone]

(NORTH AMERICA)

1 800 547-8629

Made in Canada

GE Multilin

REV. D

CH1 Clock Configuration LED
CH2 Clock Configuration LED

FRONT VIEW REAR VIEW

842837A1.cdr

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

Figure 3–44: C37.94SM TIMING SELECTION SWITCH SETTING

Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the follow­ing figure.

The clock configuration LED status is as follows:

Figure 3–45: STATUS LEDS

• Flashing green — loop timing mode while receiving a valid data packet

3-42 D30 Line Distance Protection System GE Multilin

3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS

• Flashing yellow — internal mode while receiving a valid data packet

• Solid red — (switch to) internal timing mode while not receiving a valid data packet

The link/activity LED status is as follows:

• Flashing green — FPGA is receiving a valid data packet

• Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit"

• Solid red — FPGA is not receiving a valid packet or the packet received is invalid

3

GE Multilin D30 Line Distance Protection System 3-43

3

3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS 3 HARDWARE

3-44 D30 Line Distance Protection System GE Multilin

4 HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

4 HUMAN INTERFACES 4.1ENERVISTA UR SETUP SOFTWARE INTERFACE 4.1.1 INTRODUCTION

The EnerVista UR Setup software provides a graphical user interface (GUI) as one of two human interfaces to a UR device.
The alternate human interface is implemented via the device’s faceplate keypad and display (see the Faceplate interface
section in this chapter).

The EnerVista UR Setup software provides a single facility to configure, monitor, maintain, and troubleshoot the operation
of relay functions, connected over local or wide area communication networks. It can be used while disconnected (offline)
or connected (online) to a UR device. In offline mode, settings files can be created for eventual downloading to the device.
In online mode, you can communicate with the device in real-time.

The EnerVista UR Setup software is provided with every D30 relay and runs on Microsoft
and XP. This chapter provides a summary of the basic EnerVista UR Setup software interface features. The EnerVista UR
Setup Help File provides details for getting started and using the EnerVista UR Setup software interface.

To start using the EnerVista UR Setup software, site and device definition are required. See the EnerVista UR Setup Help
File or refer to the Connecting EnerVista UR Setup with the D30 section in Chapter 1 for details.

Windows 95, 98, NT, 2000, ME,

4.1.2 CREATING A SITE LIST

4.1.3 ENERVISTA UR SETUP OVERVIEW

a) ENGAGING A DEVICE

The EnerVista UR Setup software can be used in online mode (relay connected) to directly communicate with the D30
relay. Communicating relays are organized and grouped by communication interfaces and into sites. Sites can contain any
number of relays selected from the UR-series of relays.

b) USING SETTINGS FILES

The EnerVista UR Setup software interface supports three ways of handling changes to relay settings:

• In offline mode (relay disconnected) to create or edit relay settings files for later download to communicating relays

• While connected to a communicating relay to directly modify any relay settings via relay data view windows, and then
save the settings to the relay

• You can create/edit settings files and then write them to the relay while the interface is connected to the relay

Settings files are organized on the basis of file names assigned by the user. A settings file contains data pertaining to the
following types of relay settings:

• Device definition

• Product setup

• System setup

• FlexLogic

• Grouped elements

• Control elements

• Inputs/outputs

• Testing

Factory default values are supplied and can be restored after any changes.
The following communications settings are not transferred to the D30 with settings files.

Modbus Slave Address
Modbus TCP Port Number
RS485 COM2 Baud Rate
RS485 COM2 Parity
COM2 Minimum Response Time

4

GE Multilin D30 Line Distance Protection System 4-1

4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4 HUMAN INTERFACES

COM2 Selection
RRTD Slave Address
RRTD Baud Rate
IP Address
IP Subnet Mask
Gateway IP Address
Ethernet Sub Module Serial Number
Network Address NSAP
IEC61850 Config GOOSE ConfRev

When a settings file is loaded to a D30 that is in-service, the following sequence occurs:

1. The D30 takes itself out of service.

2. The D30 issues a

3. The D30 closes the critical fail contact.

c) CREATING AND EDITING FLEXLOGIC

You create or edit a FlexLogic equation in order to customize the relay. You can subsequently view the automatically gener­ated logic diagram.

4

d) VIEWING ACTUAL VALUES

You can view real-time relay data such as input/output status and measured parameters.

UNIT NOT PROGRAMMED major self-test error.

e) VIEWING TRIGGERED EVENTS

While the interface is in either online or offline mode, you can view and analyze data generated by triggered specified
parameters, via one of the following:

• Event recorder

The event recorder captures contextual data associated with the last 1024 events, listed in chronological order from
most recent to oldest.

• Oscillography

The oscillography waveform traces and digital states are used to provide a visual display of power system and relay
operation data captured during specific triggered events.

f) FILE SUPPORT

• Execution: Any EnerVista UR Setup file that is opened launches the application or provides focus to the already
opened application. If the file was a settings file (has a URS extension) that had been removed from the Settings List
tree menu, it is added back to the Settings List tree menu.

• Drag and Drop: The Site List and Settings List control bar windows are each mutually a drag source and a drop target
for device-order-code-compatible files or individual menu items. Also, the Settings List control bar window and any
Windows Explorer directory folder are each mutually a file drag source and drop target.

New files that are dropped into the Settings List window are added to the tree, which is automatically sorted alphabeti­cally with respect to settings file names. Files or individual menu items that are dropped in the selected device menu in
the Site List window are automatically sent to the online communicating device.

g) FIRMWARE UPGRADES

The firmware of a D30 device can be upgraded, locally or remotely, via the EnerVista UR Setup software. The correspond­ing instructions are provided by the EnerVista UR Setup Help file under the topic “Upgrading Firmware”.

If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first
in EnerVista under Maintenance > Update Firmware.

4-2 D30 Line Distance Protection System GE Multilin

4 HUMAN INTERFACES 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE

NOTE

Before backing up settings and upgrading, set the Settings > Product Setup > Security > Dual Permission Security
Access > Remote Setting Authorized and Local Setting Authorized settings to "ON." Otherwise, the upgrade is blocked

and results in an "Unable to put relay in flash mode" message.

Modbus addresses assigned to firmware modules, features, settings, and corresponding data items (that is, default
values, minimum/maximum values, data type, and item size) can change slightly from version to version of firm­ware. The addresses are rearranged when new features are added or existing features are enhanced or modified.

EEPROM DATA ERROR message displayed after upgrading/downgrading the firmware is a resettable, self-test

The
message intended to inform users that the Modbus addresses have changed with the upgraded firmware. This
message does not signal any problems when appearing after firmware upgrades.

4.1.4 ENERVISTA UR SETUP MAIN WINDOW

The EnerVista UR Setup software main window supports the following primary display components:

1. Title bar that shows the pathname of the active data view

2. Main window menu bar

3. Main window tool bar

4. Site list control bar window

5. Settings list control bar window

6. Device data view windows, with common tool bar

7. Settings file data view windows, with common tool bar

8. Workspace area with data view tabs

9. Status bar

10. Quick action hot links

4

GE Multilin D30 Line Distance Protection System 4-3

4

1

2

3

4

5

6

7

8

9

842786A2.CDR

10

4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4 HUMAN INTERFACES

Figure 4–1: ENERVISTA UR SETUP SOFTWARE MAIN WINDOW

4-4 D30 Line Distance Protection System GE Multilin