Café™ 30" Single Wall Oven
with Advantium® Technology
CSB9120SJ
FEATURES & BENEFITS
Speedcook oven (120V) – Enjoy oven-quality results two to four times
faster than a conventional oven
Multiple cooking functions – Expand your cooking versatility with an all-in
one oven
Halogen heat – Skip the preheating with nearly instantaneous
halogen heat
Over 175 preprogrammed menu selections – Preprogrammed selections
make meals easy
Custom recipe saver – Conveniently store cooking instructions for up
to 30 dierent recipes
Allows for use with JX2200/2201 storage drawer
Under-the-counter installation flexibility
FEATURES
Cooking Modes
Style Built-In
Control Type Dial; Glass Touch
Interior Oven Light Ye s
Oven Interior Stainless Steel
Microwave Watts (IEC-705) 950
Turntable Size 16 in
Control Features
Cooking Technology Advantium
Oven Rack Features Pedestal Rack
Broil; Speedcook; Convection;
Microwave; Proof, Warm
Back; Cancel/O; Favorite Recipe; Help;
Lock Controls; Options; Power Temp;
Start/Pause; Timer On/O
CAPACITY
Total Capacity (cubic feet) 1.7
POWER / RATINGS
Electrical Input - 120V Amperage 15
Electrical Input - 120V Watts 1800
Volts/Hertz 120V; 60Hz
Broiler Wattage 1200W
WEIGHTS & DIMENSIONS
Approximate Shipping Weight 87 lb
Cavity (W x H x D) 20-1/16 x 8-1/2 x 17 in
Net Weight 77 lb
Overall Height 18-1/8 in
Overall Width 29-3/4 in
Overall Depth 21-1/2 in
Cabinet Width 30 in
ACCESSORIES
Metal Oven Pan Yes
APPEARANCE
Color Appearance Stainless Steel
Handle Stainless Steel; Café
Café™ 30" Single Wall Oven
C
2x4’s or
equivalent
solid floor
4-3/16"
25-1/4"
Cutout width
Junction
box location
17-1/2"
Cutout height
29-3/4"
19"
21-1/2"
Back of Control
Conduit
(48-1/2"
long)
B
30"
5" min.from
floor 1" min.
above toekick
A
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
23-1/2"
Cutout depth
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
3" MIN between cutouts
recommended—2" MIN required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16"
Conduit
(46" long)
Cabinet width
21-1/2"
To back
of Control
19"
29-3/4"
C
C
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
4-3/16"
25-1/4"
Cutout width
Junction
box location
17-1/2"
Cutout height
29-3/4"
19"
21-1/2"
Back of Control
Conduit
(48-1/2"
long)
B
30"
5" min.from
floor 1" min.
above toekick
A
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
23-1/2"
Cutout depth
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
29-3/4"
C
4-3/16"
25-1/4"
Cutout width
Junction
box location
17-1/2"
Cutout height
29-3/4"
19"
21-1/2"
Back of Control
Conduit
(48-1/2"
long)
B
30"
5" min.from
floor 1" min.
above toekick
A
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
23-1/2"
Cutout depth
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
with Advantium® Technology
CSB9120SJ
ADVANTIUM WALL OVEN/GE CAFÉ™ SERIES COOKING TOWER
DIMENSIONS AND CABINET INSTALLATION INFORMATION (IN INCHES)
Note: Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least a 194°F
temperature rating.
Note: 2" minimum between cutouts when installed
above warming drawer or single wall oven.
Installation Information:
Before installing, consult installation instructions
packed with product for current dimensional data.
Note: Advantium wallovens can be installed below
GE/GE Profile Series non-downdraft gas and electric
cooktops. It CANNOT be installed below induction
or Monogram (2GU3841385) gas cooktops.
Note: Advantium wall oven comes with two lower
trim pieces. One is for use above 36-inch height
installations and one is for use below 36-inch
installations. Use of the accessory drawer will
replace the bottom trim piece for applicable
installations. Please see installation instructions for
full details.
For answers to your Café™ product questions, visit our website at cafeappliances.com.
Suitable
bracing
to support
runners
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
C
L
21-5/8"
over centerline
of cabinet
2x4’s or
equivalent
solid floor
Café™ 30" Single Wall Oven
with Advantium® Technology
CSB9120SJ
PREPARATION WITH AN ACCESSORY DRAWER
Prepare the opening
The Advantium 120V can be installed in combination with other
Built-In appliances. Always follow each product's Installation
Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to
the dimensions shown.
* For existing cutouts, a maximum width of 28-1/2" is acceptable. If the
opening is slightly wider, secure a furring strip on each side of the
cutout for securing the oven.
• The unit overlap on the top is 1/2” but allow 5/8" clearance from top
edge of cutout. The unit overlap on each side is 2−1/4" but allow
2−3/8" clearance from side edges of cutout. The unit overlap on the
bottom is 5/8" but allow 3/4" clearance from bottom edge of cutout.
• Oven overlaps will conceal cut edges on all sides of the opening.
Note: PSB9120 series Advantium can be installed below GE/GE
Profile non-downdraft gas and electric cooktops. It CANNOT be
installed below induction or Monogram (2GU3841385) gas cooktops.
Note: PSB9120 series Advantium oven comes with two lower trim
pieces. One is for use above 36-inch height installations and one is
for use below 36-inch installations. Use of the accessory drawer will
replace the bottom trim piece for applicable installations. Please see
installation instructions for full details.
Preparation with a Warming Drawer
When installed over a single oven or a warming drawer, allow at least
2" between the two openings. This separation will provide clearance
for bottom overlap of the Advantium and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min. thick plywood supported
by 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidly mounted, flush with the
bottom edge of the cutout.
Note: Additional clearances between the cutouts may be required.
23-1/2"
25-1/4"
36-3/4" Min.
from floor
1" Min.
above
toekick
30"
21"
Installation over Warming Drawer:
23-1/2"
25-1/4"
Min.
36-3/4" Min.
from floor
1" Min.
above
toekick
30"
21"
Construct base -
Min. 3/8" plywood
supported by 2x4
or 2x2 runners all
four sides.
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
2" Min.
(3" recommended)
Per warming
drawer
requirement
Installation over a BUILT-IN Oven and Warming Drawer:
Note: Additional clearances between the cutouts may be required.
Check to be sure the oven supports above the Warming Drawer
location do not obstruct the required interior depth and height. See
Warming Drawer installation instructions for details.
Caution: For personal safety, the mounting surface must be capable
of supporting the cabinet load, in addition to the added weight of the
oven and drawer, plus additional oven loads.
For answers to your Café™ product questions, visit our website at cafeappliances.com.
Installation over a Wall Oven and Warming Drawer:
45-1/4" Min.
from floor
1" Min.
above
toekick
30"
21"
23-1/2"
Construct solid
bottom - Min. 3/8"
plywood supported
25-1/4"
Min.
Per warming drawer requirement
by 2x4 or 2x2
runners all four
sides
2" Min.
(3" recommended)
Per oven
requirement
2" Min.
© 2020 GE Appliances PC 95219 10/20
Loading...