GE CSB9120, PSB9120, ZSC1201, ZSC1202, CWB7030 Installation Instructions
...
Installation
Instructions
Advantium® 120V
Built-In SpeedCook
and 120V Built-In
Convection Ovens
CSB9120
PSB9120
ZSC1201
ZSC1202
CWB7030
PWB7030
CWB713
MFL59060930_00
31-2000001-6
07-20 GEA
Español
For a Spanish version of this manual, visit
our Website at GEAppliances.com.
Para consultar una version en español de
este manual de instrucciones, visite nuestro
sitio de internet GEAppliances.com.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT
for local inspector’s use.
IMPORTANT
and ordinances.
• Note to Installer — Be sure to leave these
instructions with the Consumer.
• Note to Consumer — Keep these instructions
with your Owner’s Manual for future reference.
• Skill Level — Installation of this appliance
requires basic mechanical and electrical skills.
• Completion Time — 1 Hour.
• Proper installation is the responsibility
of the installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.
NOTE: This oven is only approved to be installed
under the specific models as labeled on this unit.
IMPORTANT
intended purpose. Never use the oven for
warming or heating a room. Prolonged use
of the oven without proper ventilation can be
hazardous.
—
Save these instructions
—
Observe all governing codes
—
Use this oven only for its
CONTENTS
Design Information
Models Available
Product Dimensions and Clearances
Tools Required
Parts Supplied
Advance Planning
Installation Preparation
Electrical Requirements
Preparing the Opening (Standard)
Preparing the Opening (Flush Mount) ..........9-10
Storage Drawer Preparation
Standard
Flush
Installation Instructions
Step 1, Remove Packaging and Parts
Step 2, Door Trim Removal for above 36”
Installation only
Step 3, Slide the Oven into the Cutout
Step 4, Install Bottom Trim
Step 5, Install Bottom Trim with Accessory
Drawer
Step 6, Install Mounting Screws
Step 7, Finalize Installation
.........................................................11
...............................................................11
...........................................................14
...............................................2
................3
..................................................3
...................................................3
.............................................3
....................................4
.................5-8
............12
...............................................13
...........13
..............................14
......................14
.............................14
CAUTION
house fuse or oven circuit breaker before
beginning installation to avoid severe or fatal
shock injury.
CAUTION
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of the oven and drawer, plus additional oven
loads.
CAUTION
Convection 120V Oven below 36Ǝ, you must
use the plastic bottom trim due to burn risk
to children. The plastic trim acts as insulation
and will help prevent burns to children from hot
surfaces.
For personal safety, remove
For personal safety, the
If installing the Advantium/
MODELS AVAILABLE
Profile Models:
PSB9120WW – White*
PSB9120BB – Black
PSB9120SS – Stainless Steel
PSB9120ES – Slate
PWB7030SL – Stainless Steel
PWB7030EL – Slate
PSB9120BL – Black Stainless Steel
Monogram Models:
ZSC1201SS – Stainless Steel
ZSC1202SS – Stainless Steel**
Café Models:
CSB9120SS – Stainless Steel
CWB7030SL – Stainless Steel
CWB713P2NS1 – Stainless Steel
*No color-matched drawer available for this
model.
**This unit cannot be installed with an
accessory storage drawer.
2
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
21-1/2Ǝ
1Ǝ
1Ǝ
1-3/16Ǝ
13Ǝ
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
• #2 Phillips screwdriver
•
Hand-held drill
•
High speed drill bit, 3/32Ǝ diameter
•
3/8Ǝ slot-head screwdriver
•
Level
•
Saw
•
3/8Ǝ min. plywood for floor (if required)
•
Wood screws or other hardware for installing
runner or shelf to support oven (if required)
Safety glasses or goggles
•
FLUSH MOUNT INSTALLATION
(Monogram Only)
This installation method allows for the unit face to
be inline with the cabinet face.
IMPORTANT: HIGH SKILL LEVEL IN
CARPENTRY IS REQUIRED. Non-standard
cabinetry may be required.
Flush installation of the oven will lead to the
exposure of the cabinet face frame edges.
Side cleats may be visible and should be a
finished surface.
29-3/4Ǝ
19Ǝ
ADVANCE PLANNING
•7KHVHRYHQVPD\EHLQVWDOOHGGLUHFWO\LQWRDƎ
wide oven cabinet with standard installation.
•
Cutout height dimensions are different for
installations with an accessory storage drawer.
Make sure to use the correct cutout when
preparing the opening.
• Allow for clearance to adjacent corners, walls,
drawers, etc.
• Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least 194ºF
temperature rating.
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer
must be assembled to the oven prior to
installation into the cabinet. See the Accessory
Storage Drawer Assembly Instructions.
3
Installation Preparation
ELECTRICAL REQUIREMENTS
Single Advantium/Convection 120
Installation:
This product requires a 120-volt, 60 Hz, 15-amp
circuit and draws 1.8 kilowatts. This product must
be connected to a supply circuit of the proper
voltage and frequency.
• Wire size must conform to the requirements of
the National Electrical Code or the prevailing local
code for this kilowatt rating.
• The power supply cord and plug should be
brought to a separate 15 or 20 ampere branch
circuit single grounded receptacle. The outlet box
should be located within reach of the 48” power
cord.
ELECTRICAL LOCATION
6”
GROUNDING
INSTRUCTIONS
This appliance must be grounded. In the event of
an electrical short circuit, grounding reduces the
risk of electric shock by providing an escape wire
for electric current. This appliance is equipped
with a cord having a grounding wire with a
grounding plug. The plug must be plugged into
an outlet that is properly installed and grounded.
9”
Locate outlet box in the shaded area
Install a recessed electrical outlet in the back
wall of the opening within 6Ǝ of either side and
at least 9Ǝ above the cutout floor.
WARNING
Improper use of the
grounding plug can result in a risk of
electric shock.
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped with
a three-prong (grounding) plug that mates with a
standard three-prong grounding wall receptacle
to minimize the possibility of electric shock.
Consult a qualified electrician or serviceman if
the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the consumer to have it replaced with
a properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
DO NOT USE AN EXTENSION CORD. If the
power supply cord is too short, have a qualified
electrician or serviceman install an outlet near the
appliance.
4
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING
The Advantium/Convection 120 can be installed
in combination with other Built-In Appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium/Convection 120
Installation:
Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
30”
17-1/2”
36-3/4”
Min.
23-1/2”
25-1/4”
Construct
solid bottom
- Min. 3/8”
plywood
supported
on all four
sides. Must
be able to
support
weight of
oven and
contents.
PREPARE THE OPENING (CONT.)
Installation over a Warming Drawer:
30”
17-1/2”
36-3/4”
Min.
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location does
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
23-1/2”
25-1/4”
Construct
solid bottom
- Min. 3/8”
plywood
supported
on all four
sides. Must be
able to support
weight of oven
and contents.
2” Min.
(3” Recommended)
Per Warming
Drawer
Requirement
•
Allow the following clearances
around the cutout on the front surface of the
FDELQHW´IURPWKHWRSí´IURPWKH
VLGHHGJHVDQGí´IURPWKHERWWRP1RWH
these refer to minimum clearances required for
installation and do not reflect actual product
dimensions.)
Oven overlaps will conceal cut edges on all
•
sides of the opening.
When installed over a single oven or a
warming drawer, allow at least 2” between
the two openings. This separation will provide
clearance for bottom overlap of the Advantium/
Convection 120 and the other appliance
overlaps.
The support must be level and rigidly mounted,
•
flush with the bottom edge of the cutout.
5
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING (CONT.)
Installation over a Wall Oven:
Construct
30”
23-1/2”
25-1/4”
17-1/2”
45-1/4”
Min.
* If you are replacing an electric double oven
with the combined installation of an Advantium/
Convection 120 and a single oven, use the
dimensions shown. The middle rail separating
the two openings may need to be larger than
the 2” minimum shown.
solid bottom
- Min. 3/8”
plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
2” Min.
(3” Recommended)
Per Oven
Requirement
PREPARE THE OPENING (CONT.)
Installation over a Wall Oven and
Warming Drawer:
30”
23-1/2”
25-1/4”
17-1/2”
45-1/4”
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
location does not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Construct
solid bottom Min. 3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
2” Min.
(3” Recommended)
Per Oven
Requirement
2” Min.
(3” Recommended)
Per Warming
Drawer
Requirement
CAUTION
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of the oven and drawer, plus additional oven
loads.
6
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING (cont.)
Installation over another Built-In
SpeedCook Oven:
30Ǝ
17-1/2Ǝ
17-1/2Ǝ
23-1/2Ǝ
25-1/4Ǝ
Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
2Ǝ Min.
(3Ǝ Recommended)
PREPARE THE OPENING (cont.)
Installation under a Microwave Oven and
over a Warming Drawer:
Construct
30Ǝ
Per Microwave
Oven Requirement
17-1/2Ǝ
Per Warming
Drawer
Requirement
23-1/2Ǝ
25-1/4Ǝ
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.
3.5Ǝ Min.
(4.5Ǝ Recommended)
2Ǝ Min.
(3Ǝ Recommended)
•
If you are mounting a Built-In
over another, use the dimensions
SpeedCook Oven
shown. The
middle rail separating the two openings may
need to be larger than the 2Ǝ minimum shown.
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming Drawer
locatio n d o not obstruct the required interior
depth and height. See War m in g Dr aw e r
installation instructions for details.
CAUTION
For personal safety, the
mounting surface must be capable of supporting
the cabinet load, in addition to the added weight
of the oven and drawer, plus additional oven
loads.
7
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING (cont.)
Installation beside another Built-in
Speedcook Oven:
• If you are mounting a
another, use the dimensions shown. The
middle rail separating the two openings may
need to be larger than the 4-1/2Ǝ minimum
shown.
SpeedCook Oven
beside
PREPARE THE OPENING (cont.)
17-1/2Ǝ
25-1/4Ǝ
23-1/2Ǝ
25-1/4Ǝ
17-1/2Ǝ
4-1/2Ǝ Min.
(5-1/2Ǝ Recommended)
Installation under a 30Ǝ or 36Ǝ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the
cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate,
properly grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply.
Use a 36Ǝ or wider base cabinet.
1-1/2Ǝ Min.
25Ǝ
36Ǝ
Countertop
Height
Ǝ
Cooktop height including depth
of electrical box on some
models. Refer to cooktop
installation instructions.
No minimum clearance required
between cooktop and oven.
23-1/2
4Ǝ High
Toekick
Cooktop
Cooktop
17-1/2
25-1/4Ǝ
Ǝ
NOTE: The oven is only approved to be installed
under the specific models as labeled on the unit.
8
Flush Mount Installation Preparation (Monogram Only)
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE INTERIOR
Cut and install side cleats:
• Cut side wood cleats to height of cabinet
opening and approx. 2-1/2” in depth. Install,
on each side, Dim. E from the front face of the
cabinet.
Cut and install bottom cleat:
• Cut bottom wood cleat to a height of 1-1/8”, a
depth of the cabinet minus Dim. E and a width
of 25-1/4” to fit between side cleats. Install
onto the cabinet floor between the side cleats,
push it all the way back against cabinet wall
and make sure its front face aligns with the front
faces of the side cleats (Dim. E gap from the
front cabinet face).
A
A
PREPARE THE OPENING
The Advantium 120 can be installed in
combination with other Built-In appliances.
Always follow each product’s Installation
Instructions to complete the installation.
Single Advantium 120 Installation:
Cut the opening in a cabinet to the dimensions
shown.
*See table
below for
desired reveals
on sides.
**19-1/4”
23-1/2” min.
F *
Oven or
warming
drawer
Construct
solid bottom
- Min. 3/8”
plywood
supported on
all four sides.
Must be able to
support weight
of oven and
contents.
2” Min.
Per
appliance
specs.
C
B
Side and top cleats depth 2-1/2” min.
A
Bottom cleat height 1-1/8”
B
Bottom cleat depth Cabinet depth minus
C
Bottom cleat width 25-1/4”
D
All four cleats inset depth 1 3/16”
E
D
E
Dim. E”
D
C
TOP
VIEW
A A
36-3/4”
Min.
• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.
Approved Flush Installation
Single Advantium 30” 30-1/4”
Over Warming Drawer 30” 30Over Oven
Over Oven and Warming Drawer
Over Built-in Speedcook Oven
Double Advantium (side by side)
Under Cooktop or Countertop See page 10
Dimension F
1/8” Reveal 1/4” Reveal
1
/4”
30” 30-1/4”
30” 30-1/4”
30” 30-1/4”
See page 10
** Top and bottom reveals are set to 1/8”.
Front Face of Cabinet
EE
9
Flush Mount Installation Preparation (Monogram Only)
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or
combined installation unless plastic trim is installed.
PREPARE THE OPENING
The Advantium/Convection 120 can be installed beside
another Advantium/Convection 120 in a side-by-side
combination.
Double Advantium/Convection 120
Installation:
Cut the opening in a cabinet to the dimensions shown.
• Center divider acts as cleat for side of each respective
unit. Only one additional side cleat needed per oven
cutout.
• The support must be level and rigidly mounted, flush
with the bottom edge of the cutout.
*See table for desired reveals on sides and
between unit.
Dimension 1/8” Reveal 1/4” Reveal
G 59-7/8” 60-1/4”
H 5-1/8” 5-1/4”
I 27-3/8” 27-1/2”
23-1/2” min.
G*
H*
I*
I*
19-1/4”
1-3/16”
36-3/4”
Min.
Construct solid bottom - Min. 3/8”
plywood supported on all four
sides. Must be able to support
weight of oven and contents.
Installation under a 30Ǝ or 36Ǝ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size.
See the label on top of the oven for approved cooktop models. This oven requires a separate from the cooktop,
properly grounded 15-Amp, 120-Volt, 60Hz power supply. Use a 36Ǝ or wider base cabinet.
1-1/2Ǝ Min.
25Ǝ
36Ǝ
Countertop
Height
Cooktop height including depth of electrical box on some
models. Refer to cooktop installation instructions.
No minimum clearance required between cooktop and
oven.
*See table for desired reveals on sides.
Dimension 1/8”
Reveal
J 30” 30-1/4”
1/4”
Reveal
23-1/2
4Ǝ High
Toekick
Cooktop
Cooktop
19-1/4”
J*
Ǝ
NOTE: The oven is only approved to be
installed under the specific models as
labeled on the unit.
10
Loading...