PB-31101-035A
Supersedes PB-31101-035
GE Renewal Parts
Use original equipment parts for reliability
PARTS BULLETIN
DRILLING MOTOR
MODEL 5GE752RB3A
SEPTEMBER 10, 1997
E Copyright 1997 General Electric Company. All rights reserved. This copyrighted document may be reproduced free of charge by General
Electric Company customers, if such reproduction is used exclusively in connection with equipment used in that customer's internal operation.
PB-31101-035A
Supersedes PB-31101-035
107,
108,
109,
110
DRILLING MOTOR
MODEL 5GE752RB3A
103,104,105,106
115,116
118
23,24
A
7
6,9
8
94
101
2
63
VIEW AT A
(COMM. END)
82,
83
81
111,112,113,114
98
64
99
91
32,
31
4,5
3
13
12
SEPTEMBER 10, 1997 2
10
11
95
(Representative Illustration)
Ref. 1
FIG. 1
93
89
84
92
DRILLING MOTOR
MODEL 5GE752RB3A
PB-31101-035A
Supersedes PB-31101-035
90
30,
32
25
97 96
16
23,24
17
18
21,22
19
20
85,
86
91
92
87
102
100
88
(Representative Illustration)
FIG. 1 (Cont’d.)
15
14
SEPTEMBER 10, 19973
PB-31101-035A
Supersedes PB-31101-035
DRILLING MOTOR
MODEL 5GE752RB3A
44,45
42,58,59
46,48,49
37
38
33
28
47,
48,
49
51,53
64
39
60
26
31,32
41
64
64
57,58,59
64
43,58,59
26
28
33
40
VIEW AT COMMUTATOR END
(Representative Illustration)
SEPTEMBER 10, 1997 4
FIG. 2
50,
51,
52
34
DRILLING MOTOR
MODEL 5GE752RB3A
54,
55,
56,
57,
58,
59
25
PB-31101-035A
Supersedes PB-31101-035
34
62
25
61
34
26
26
35
30,
32
VIEW OF PINION END
28
25
28
61
36
25
62
(Representative Illustration)
FIG. 2 (Cont’d.)
SEPTEMBER 10, 19975
PB-31101-035A
Supersedes PB-31101-035
68
69
DRILLING MOTOR
MODEL 5GE752RB3A
70
77,
78,
79,
80
68
67
69
66
73
75
70
65
72
71
71
72
75
76
76
74
65
71
Ref. 64
Brush Holder
(Representative Illustration)
SEPTEMBER 10, 1997 6
FIG. 3
DRILLING MOTOR
MODEL 5GE752RB3A
QUANT
REQ.
FIG. REF. COL.
NO. NO. PART NO. A DESCRIPTION
Supersedes PB-31101-035
PB-31101-035A
1 1 5GE752RB3A 1 DRILLING MOTOR
1 2 4732368P1 2 GASKET, 0.021 IN THK
1 3 6739891P2 1 *BEARING CAP
1 4 N22P33048 8 BOLT, HEX HD, 5/8 IN-11, 3 IN LONG
1 5 41B537660P9 8 WASHER, FLAT, 0.725 IN ID, 1 IN OD
1 6 41C635865G2 1 *FRAME HEAD ASSEMBLY
1 7 481A560G1 1 FLASH RING
1 8 N22P29020B13 6 BOLT, HEX HD, 1/2 IN-13, 1 1/4 IN LONG
1 9 N509P2516 1 PIN, SPRING DOWEL, 1/4 IN DIA, 1 IN LONG
1 10 8864951P119 1 ROLLER BEARING
1 11 334B761P1 1 BEARING CAP
1 12 949X47 1 RETAINING NUT WITH SET SCREW
1 13 41A239107P1 2 SCREW, HEX SOC HD, 1/2 IN-13, 3/4 IN LONG
1 14 8864951P167 1 ROLLER BEARING
1 15 4713640P1 1 FLINGER
1 16 6744700P2 1 BEARING CAP, INNER
1 17 41C637314P1 1 FRAME HEAD
1 18 4732906P1 2 GASKET, 0.021 IN THICK
1 19 2739317P2 1 *BEARING CAP
1 20 4732351P1 1 SLEEVE
1 21 N22P33056 8 BOLT, HEX HD, 5/8 IN-11, 3 1/2 IN LONG
1 22 41B537660P9 8 WASHER, FLAT, 0.725 IN ID, 1 IN OD
1 23 N22P39032 11 BOLT, HEX HD, 1 IN-8, 2 IN LONG
1 24 41B537660P21 11 WASHER, FLAT, 1.063 IN ID, 2 IN OD
1 25 8855483G4 4 COIL WITH POLE PIECE, EXCITING
2 26 41C637285G7 2 COIL WITH POLE PIECE, COMMUTATING
DELETED 2 *NOT USED
2 28 41C637285G10 2 COIL WITH POLE PIECE, COMMUTATING
DELETED 2 *NOT USED
1,2 30 N22P45060 12 BOLT, HEX HD, 1 1/4 IN-7, 3 3/4 IN LONG
1,2 31 41A239559P1 12 BOLT, HEX HD, 1 1/4 IN-12, 4 IN LONG
1,2 32 41B537660P22 24 WASHER, FLAT, 1.313 IN ID, 2.500 IN OD
2 33 41C636243G2 2 CABLE ASSEMBLY
2 34 8842961G1 3 CABLE ASSEMBLY
2 35 41B531137G10 1 CABLE ASSEMBLY
2 36 41B531137G7 1 CABLE ASSEMBLY
2 37 41C637562G2 1 CABLE ASSEMBLY
2 38 41C637562G1 1 CABLE ASSEMBLY
2 39 41C637261G1 1 CONNECTION STRAP, INSULATED
2 40 41C637261G5 1 CONNECTION STRAP, INSULATED
2 41 41C637261G2 1 CONNECTION STRAP, INSULATED
2 42 41D735504G7 1 SHUNT ASSEMBLY
* ADDED OR CHANGED SINCE LAST ISSUE.
SEPTEMBER 10, 19977
PB-31101-035A
Supersedes PB-31101-035
FIG. REF. COL.
NO. NO. PART NO. A DESCRIPTION
DRILLING MOTOR
MODEL 5GE752RB3A
QUANT
REQ.
2 43 41D735504G6 1 SHUNT ASSEMBLY
2 44 481A539P32 2 CABLE BUSHING, 1 7/32 IN ID, RUBBER
2 45 41A216775P1 AR SEALANT, 1/8 BY 3 3/4 IN, 10 FT ROLL
2 46 N22P33028 1 BOLT, HEX HD, 5/8 IN-11, 1 3/4 IN LONG
2 47 N22P33024 1 BOLT, HEX HD, 5/8 IN-11, 1 1/2 IN LONG
2 48 N405P47B13 2 LOCKWASHER, 5/8 IN
2 49 N213P33 2 NUT, HEX, JAM, 5/8 IN-11
2 50 N22P27028B13 2 BOLT, HEX HD, 7/16 IN-14, 1 3/4 IN LONG
2 51 N405P44B13 12 LOCKWASHER, 7/16 IN
2 52 4713845P1 1 BOLTING PLATE
2 53 N22P27020B13 10 BOLT, HEX HD, 7/16 IN-14, 1 1/4 IN LONG
2 54 41A230733P4 8 BOLT W/WASHER, SL HX HD, 1/4 IN-20, 1/2 IN LONG
2 55 8809650P1 8 WASHER, CONCAVE, 1/4 IN, SPR STL
2 56 N203P21B13 8 NUT, HEX, 1/4 IN-20
2 57 41A239176P443 AR SILASTIC PUTTY
2 58 41A239176P133 AR SILICONE TAPE, 0.015 IN THICK, 1 IN WIDE
2 59 41A239176P18 AR *TAPE, MICA, 0.005 IN THK, 0.750 IN WIDE
2 60 41A231281P47 7 BRAZING STRIP
2 61 41A239176P399 AR CORD, 0.073 IN DIA, LINEN
2 62 41A210359P12 2 REDUCING BUSHING, 1 1/2 IN TO 3/4 IN
1 63 41B537963P1 12 CARBON BRUSH
1,2,3 64 41C632667G6 4 BRUSH HOLDER ASSEMBLY
3 65 41B530659G2 12 PRESSURE ARM
3 66 41A231370P2 12 BUSHING, 1.063 IN LONG
3 67 186V831P1 8 SLEEVE
3 68 41A231378P2 4 PIN, 3/8 IN DIA, 6 5/8 IN LONG
3 69 N509P2548 8 PIN, SPRING DOWEL, 1/4 IN DIA, 3 IN LONG
3 70 N509P912 8 PIN, SPRING DOWEL, 3/32 IN DIA, 3/4 IN LONG
3 71 41A230733P7 8 BOLT W/WASHERS, HEX HD SL, 5/16 IN-18, 3/4 IN LONG
3 72 41A231370P6 16 BUSHING, 0.575 IN LONG
3 73 41A330248P1 12 SPRING SEAT
3 74 41A233867G4 12 SPRING SEAT WITH PIN
3 75 41B537844G1 12 SPRING SET ASSEMBLY
3 76 41A233880P1 4 PIN, 7 7/16 IN LONG
3 77 41B535754G28 8 BRUSH HOLDER STUD, MOLDED (0.002 IN OVERSIZE)
3 78 41B535754G29 8 BRUSH HOLDER STUD, MOLDED (0.004 IN OVERSIZE)
3 79 41B535754G30 8 BRUSH HOLDER STUD, MOLDED (0.006 IN OVERSIZE)
3 80 41B535754G31 8 BRUSH HOLDER STUD, MOLDED (0.008 IN OVERSIZE)
1 81 2733755P7 4 BRUSH HOLDER SUPPORT CLAMP
1 82 N22P37052 4 BOLT, HEX HD, 7/8 IN-9, 3 1/4 IN LONG
1 83 41B537660P25 4 WASHER, FLAT, 0.968 IN ID, 1.375 IN OD
1 84 41D735773G1 1 ARMATURE ASSEMBLY
* ADDED OR CHANGED SINCE LAST ISSUE.
SEPTEMBER 10, 1997 8
DRILLING MOTOR
MODEL 5GE752RB3A
QUANT
REQ.
FIG. REF. COL.
NO. NO. PART NO. A DESCRIPTION
Supersedes PB-31101-035
PB-31101-035A
1 85 41C636928G1 1 SHAFT WITH PLUG
1 86 84A204808P1 2 *SET SCREW, HEX SOC HD, 3/8 IN-24, SELF-LOCK
1 87 41B537605P4 1 ARMATURE HEAD
1 88 41A239323G1 1 PUNCHING, END
1 89 41A330418G1 1 PUNCHING, END
1 90 41B537164P1 553 PUNCHING, MAIN
1 91 41B537165P1 26 PUNCHING, STEP BACK
1 92 41B537165P2 14 PUNCHING, STEP BACK
1 93 41B537889G2 1 COMMUTATOR, SEASONED
1 94 189V584P1 1 NUT
1 95 41D735370G5 1 ARMATURE REWIND KIT
1 96 41B537080P1 1 =TEFLON BAND (CONTINUOUS)
1 97 41A330208P10 AR WIRE, 0.072 IN DIA
1 98 41A239176P64 AR GLASS TAPE, 0.014 IN THICK, 3/4 IN WIDE
1 99 41A239176P62 AR GLASS TAPE, 0.014 IN THICK, 3/8 IN WIDE
1 100 41A232821P1 1 SLEEVE
1 101 2766829ADP24 AR #BALANCE WEIGHT, 13 IN OD
1 102 2766829ADP26 AR #BALANCE WEIGHT, 14 3/4 IN OD
1 103 493A204G1 1 INSPECTION COVER, TOP
1 104 493A204P3 2 GASKET, NEOPRENE, 0.250 X 0.750X93/4INLONG
1 105 493A204P4 2 GASKET, NEOPRENE, 0.250 X 0.750 X 11 IN LONG
1 106 497A806P57 AR *CEMENT
1 107 41D732878G4 1 *INSPECTION COVER, LOWER
1 108 41D732878P7 2 *GASKET, 9/16 IN X 11 9/32 IN LONG, 1/4 IN THK
1 109 41D732878P8 2 *GASKET, 9/16 INX91/2INLONG, 1/4 IN THK
1 110 497A806P57 AR *CEMENT
1 111 41A239914G1 1 INSPECTION COVER, HAND HOLE
1 112 41A239914P2 2 GASKET, 9 1/4 IN LONG, 1/4 IN THICK
1 113 41A239914P3 2 GASKET, 8 1/8 IN LONG, 1/4 IN THICK
1 114 497A806P57 AR *CEMENT
1 115 N22P29016B13 12 BOLT, HEX HD, 1/2 IN-13, 1 IN LONG
1 116 N405P45B13 12 LOCKWASHER, 1/2 IN
N5700P63 4 PIPE PLUG, 3/4 IN, CSK SQ HD
1 118 41A239663P2 4 PLUG
493A471P1 1 *HUB, 9.120 IN OD, POWER TAKE-OFF
* ADDED OR CHANGED SINCE LAST ISSUE.
# WELD OR BRAZE IN POSITION.
= ADDITIONAL MATERIAL IS REQUIRED TO INSTALL THE CONTINUOUS LOOP TEFLON BAND. SEE APPLICATION
INSTRUCTIONS, GEK-76278.
- END OF PARTS BULLETIN -
SEPTEMBER 10, 19979
PB-31101-035A
Supersedes PB-31101-035
DRILLING MOTOR
MODEL 5GE752RB3A
SEPTEMBER 10, 1997 10
GE Transportation Systems, Erie, Pennsylvania 16531
PRINTED
IN U.S.A.
E
Loading...