Page 1
Wireless Motion Sensing
LED Spotlight
User’s Manual
17453-1
Page 2
Page 3
Thank you on your
purchase of the GE
LED Spotlight
Included items:
Spotlight
2 - 25 mm screws and screw anchors
1 - 44 mm screw
The LED Spotlight time setting feature
Time can be set at either 30 seconds or 2 minutes. Unit turns on
when dark and when it detects motion. Unit turns on for the time set
by the switch ( 30 sec. or 2 min.) then turns off if no motion
is detected.
Light Sensor - The LED Spotlight only turns on in the dark to conserve battery life.
Brightness Settings -
1. “Bright” for maximum light output
2. “Dim” for maximum battery life
Remove the front cover by rotating
counter-clockwise. (see photo)
LED Spotlights time setting feature Time can be set at either 30 seconds or two minutes.
1. Setting the LED Spotlights time setting feature:
To set your automatic shut-off time to 30 seconds
or two minutes. Use a pencil to move the switch to
the desired position.
NOTE: The LED Spotlight will stay on as long as there
is motion detected.
2. Setting the brightness - Use a pencil to move the
switch to the desired position. (see photo)
Page 4
3. Inserting batteries - Open the battery compartment
and install 3D batteries, matching the polarity markings.
Replace the battery compartment, make sure
it snaps back into place.
4. Replace battery compartment - put back in the
spotlight compartment. Screw on till the arrows match.
Mounting the LED Spotlight:
Determine which mounting method you need
1. Permanent mounting - Large screw mounting
a. Remove base by removing screw in the side
of the base. (see photo)
b. Pull fixture from base by pulling out the neck
of the base.
c. Position the base in the chosen location and drive
the 44 mm screw through the top of the base
(see photo)
d. Replace the light fixture by pressing the neck back
in to the base and replace the screw snuggly in to
the side of the base.
NOTE: Only tighten finger tight to keep from cracking or breaking
the base. DO NOT OVER TIGHTEN. Replace neck and light and
tighten screw on front of base.
Page 5
7.
2. Hanging Keyhole Type Mounting
NOTE: FOR BEST PERFORMANCE, SPOTLIGHT SHOULD BE
POSITIONED SO MOTION SENSOR IS ON TOP AND LIGHT
IS ON BOTTOM.
First, use included template
to mark the area where the
screws will be inserted.
NOTE: Spotlight can be
rotated 360°, so screws can
be mounted in any position.
We recommend mounting the
screws parallel to the ground if mounting on a vertical
surface. Make sure the screws are precise distance from
each other (2-1/8” apart). (see photo)
If using anchors:
Use 3/16” drill bit to drill
holes and insert anchors.
Drive 25 mm screws into
anchors so that screw
head protrudes 1/8” from
surface (the height of
the screw head) .
If using screws only:
Use 1/8” drill bit to drill holes and insert 25 mm screws so
that screw head protrudes 1/8” from surface( the height
of the screw head).
Hang the mounting base
on the inserted screws and
slide mounting base down
so that the track is securely
held by the screws.
3.
1/8”
Page 6
7.
Reassembling The Unit:
4. Once the base is secure,
insert the neck and fixture
back in to the large hole in the
middle of the base. Tighten the
screw on the base finger tight
so that the neck and fixture
assembly are secured snuggly
within. DO NOT OVER TIGHTEN.
Positioning The Fixture:
5.
The LED Spotlight can be
rotated 360 degrees, up or
down. To adjust the light up
or down; turn winged screw
(see photo) counter clockwise,
move light to desired position
and tighten winged screw by
turning clockwise (see photo). DO NOT OVER TIGHTEN.
To adjust the angle; firmly hold main light area and
twist to desired position.
NOTE: The neck and light will rotate and click
when moving to a different position.
6.
Page 7
X
X
Mounting Template
2-1/8 in.
Center
Page 8
CAUTION
•
Batteries may leak harmful liquids or ignitable
materials or explode causing injury and
product damage
•
Do not mix old and new or other battery types
•
Replace all batteries at the same time
•
Remove batteries if product is to be unused for
extended periods of time
PRECAUCIÓN
• Las pilas pueden desprender líquidos nocivos o
materiales inflamables que pueden causar daño
al usuario o al producto
• No se deben usar juntas pilas nuevas y viejas o
distintos tipos de pilas
• Cambie todas las pilas al mismo tiempo
• Retire las pilas si el producto se va a utilizar
durante largos períodos de tiempo
is a trademark of the General Electric
Company and is used under license to Jasco
Products Company LLC, 10 E. Memorial Road,
Oklahoma City, OK 73114.
This Jasco product comes
with a 1 year limited warranty.
Visit www.jascoproducts.com for details.
17453-1
1/19/10
Loading...