GB SPR300+ User Manual

05/06

From #174-1

OPERATINGINSTRUCTIONS

ACSNAP-AROUNDVOLT-OHM-AMMETER

MODELSPR-300PLUS&SPR-300PLUSA

1) FEATURES

・

UL Listed

・

New range finder symbols give quick and easy locations of all ranges.

・

Three functions, nine ranges

.

・

Large optically clear window gives quick, easy distortion

-

free readings.

・

One AA type battery AWS Part AWS B-1 included.

・

Two fuses(one spare), both included. AWS Part #F-1

.

・

Volt, Ohm and Common terminals are on the front panel.

・

Ohm scale on dial drum

.

・

Industry standard safety shielded banana plugs and recessed input terminals included.

・

Pointer lock device to freeze readings

.

・

1.5 Ampere range for low current equipment.

2) SPECIFICATIONS

Range : AC Current 6/20/60/200/600 Aac

AC Voltage 150/300/600 Vac
Resistance 0-2K/25 ohm mid scale
Accuracy : AC Current ±3% of full scale at 50-60Hz
±6% of full scale except 6A range at 400Hz
10% of full scale on 6A range at 400Hz
AC Voltage ±3% of full scale
Resistance ±3% of arc length
Withstand Voltage : 2,500 V AC for one minute between electrical circuit and

housing case or metal section of transformer jaws

.

LIFETIME LIMITED WARRANTY

The attention to detail of this fine snap-around instrument is further enhanced by
the appl ic at io n of Sp er ry 's unmatche d se rv ice and c on ce rn for de ta il a nd
reliability.
The se S pe rr y snap-around s ar e in ternationally a cc ep te d by craftsma n an d
se rvi cem en for th e ir unm atc hed pe r fo r man ce. Al l S per r y' s sn ap- aro und
instruments are unconditionally warrante d ag ai ns t de fe ct s in m at er ia l an d
workmanship under normal conditions of use and service; our obligations under
this warranty being limited to repairing or replacing, free of charge, at Sperry's
sole option, any such Sperry snap-around instr ument t hat mal functions under
normal operating conditions at rated use.

1

REPLACEMENT PROCEDURE

Securely wrap the instrument and its accessories in a box or mailing bag and
ship prepaid to the address below. Be sure to include your name and address, as
well as the name of the distributor, with a copy of your invoice from whom the
unit was purchased, clearly identifying the model number and date of purchase

.

Sperry Instruments

ATT : Customer Service Dept

.

2150 Joshua's Path, Suite 302,

Hauppauge, NY 1178

8

1

The warranty is not applicable if the instrument has been misused, abused,

subjected to loads in excess of spec

ifications, has had unauthorized repair or has

been improperly assembled or used

.

4.5) HOW TO USE POINTER LOCK & RANGE FINDER
SYMBOLS

(1) Slide the pointer lock button to the left. This allows easy readings in dimly lit

or crowded cable areas (Fig.8).

(2) For quick and easy identi

fication the dial drum is marked with the symbols as

illustrated below (Fig.9).

5) BATTERY & FUSE REPLACEMENT

(1) Remove the screw on the back of the case for battery and fuse replacement

(Fig.10). Replace only with AWS fuse part F-1 or approved equal. 1/2A, 250V,

1/4"×1-1/4" Fast acting High Current interrupting style fuse.
CAUTION : For continued protection against fire, replace only with fuse of the
specified voltage current and rupture speed ratings.

(2) The battery and fuse are installed inside the case (Fig.11).

6) RETURN FOR REPAIR

Before returning your instrument for repair make sure the failure to operate is
not caused by:

1) Weak or de-energized battery

2) Fuse blown

3) Broken test leads

4) Pointer lock closed
If all of these conditions are checked to be

fine and your instrument still does not

operate properly then send it bake freight prepaid to:

Sperry Instruments

2150 Joshua's Path, Suite 302

Hauppauge, NY 11788
Include all accessories and a note explaining what is wrong with the instrument.
Should you require an estimate please indicate ESTIMATE ONLY on your note. Be
certain to include your return address and day time phone number should we
need to contact you.

Ampere
range
to the
right.

Lower
range
to the
left.

Higher
range
to the
right.

Lower
range
to the
left.

Pointer
Lock

Fig.8 Fig.9

Fig.10 Fig.11

Back
Case
Screw

Spare
Fuse

Battery

Fuse

(2) Set the range switch to the highest Vac range position.
(3) Connect the test leads to the circuit under test (Fig.4) and read the voltage

directly on the scale

.

(4) When the reading is less than one half of the scale set the range switch to the

next lower range position. For maximum accuracy, select the lowest range
possible without overranging the meter.

4.4) RESISTANCE MEASUREMENTS

WARNING

!

Attempting resistance measurements on live circuits can cause electrical
shock, damage to the instrument and damage to the equipment under
test. Resistance measurements must be made on de-energized (DEAD)
circuits only for maximum personal safety. The fuse protection installed
in this instrument will reduce the possibility of damage to the instrument
but not necessarily avoid all damage or shock hazard

.

Never jump out the protective fuse. Replace the fuse with AWS Part #F-1 or approved
equal. Only use fuses that are quick acting and have high current interrupting capacities.
(1) Teat the circuit to make sure it is de-energized. Refer to section 4.3 on how

to test for voltage.

(2) Set the range switch to the ohm range position. Insert the red test lead into

the “OHM” terminal and black test lead into the “COM” terminal

(

Fig.

5).

(3) With the test leads open set the pointer over the

“∞”

(

infinit

y)mark at the left

end

of the ohm scale, using the zero adjust screw.

(4) With the test leads shorted set the pointer over the “0”mark at the right end

of the ohm scale, using the ohm zero adjust knob (Fig.6).

Note : When this adjustment does not bring the pointer over the “0”mark replace the

battery.

(5) Connect the test leads to the circuit under test (Fig.7) and read the resistance

dire

ctly on the scale.

Insulation Protection : 10MΩ min. at 1000 V between electrical circuit and

housing or metal section of transformer jaws.

Overload Protection : AWS Par t # F-1,0.5A, 250V, 1/4"×1-1/4" fus e a nd

diod

e

Frequency Response : 50-400Hz
Conductor Size : Approx. 1.2"(30mm)
Dimensions : 8.7"(L)×3.3"(W)×1.6"(D)

220mm (L) ×83mm (W) ×40mm (D)

Weight : Approx. 13.8 oz. (390g)battery included
Power Source : One 1.5V AA size battery, AWS Part #B-1
Fuse : 1/4"×1-1/4", .5A, 250V FF AWS Part #F-1
Temperature : 5

℃

t o

4 0℃ M ax R H 8 0% to 3 1℃, dec r ea s ing

linearl

y to 50% RH at 40℃

Cleaning : Wipe with a clean dry cloth.
Accessories : (included)

Test Leads Model TL-52 one alligator, one with prod

.

Banana Plugs are shrouded, Battery B-1, AA type 1.5V.

Two 0. 5/ 250 V Fu ses F -1 (spa re fuse i nclud ed ),

durable Case C-53.

     

(optional) Energizer Model E-1, AG -940, TL-5, TL-5-A1, TL6,



TL6- A1 , T L- 39, T L-42, T L-4 4, TL -4 8, TL -4 9 a nd

C-53A Carrying Case.
Instrument complies with insulation category (Overvoltage Category ll). Pollution
Degree 2 in accordance with IEC-664. Indoor use.
If the

equipment is used in a manner not specified, the protection provided by

the equipment may be impaired.

3) SAFETY PRECAUTIONS

The following safety precautions must be observed to insure maximum personal
safety during the operation, service and repair of this meter :

1. R ea d th es e op er ating instr uc ti on s th or oughly and co mp le te ly b ef ore

operatin

g your meter. P ay particular attention to WARNINGS which w ill

in

form you of potentially dangerous procedures. The instruction in these

warnings must be followed.

2. Always insp ect y our m eter, test lead s and acce ssories for any si gn of

da

mage or abnormality before every use. If any abnormal conditions exist

(e

g. b roken test le ads, cracked cases, etc.), do not attem pt to take an y

measurements. Refer to Return for Repair section.

3.

Do not expose the instrument to direct sunlight, extreme temperature or moisture.

4. Never ground yourself when taking electrical measurements. Do not touch

exp os ed metal pi pes, outl et s, fixture s, e tc., whic h might be at ground
potential.

Keep your body isolated from ground by using dry clothing, rubber

shoes, rubber mats, or any approved insulating material.

5. To avoid electric shock use CAUTION when working with Voltages above 40

Vdc or 20 Vac. Such voltages pose a shock hazard.

6.

Never exceed the maximum allowable input value of any function when taking

a measurement. Refer to the specifications on page 1 for maximum inputs

.

7. Never touch exposed wiring, connections or any live circuit when attempting

to take measurements.

8. Do not attempt to operate this instrument in an explosive atmosphere (i. e.

in the presence of flammable gases or fumes, vapor or dust).

9. When testing for the presence of voltage, make sure the voltage function is

ope ra ti n

g p ro pe rl y by r eading a known vo lt ag e in t ha t function befo re

assumin

g that a zero reading indicates a no-voltage condition. Always test

your meter before and after taking measurements on a known live circuit.

10.

Cal ib ra tion and re pa ir of any i ns trument s ho uld only be p erformed by

qualified and trained service technicians.

11.

Do not attempt calibration or service unless trained and another person,

capable of rendering first-aid and resuscitation, is present.

12.

Do not install substitute parts or perform any unauthorized modification of

the instrument.

Return the instrument to Sperry Instruments, Inc. for service

and repair to insure that safety features are maintained.

4) OPERATION

BE F O R E PR O C E E DING W I T H AN Y M E ASUR E M E N T, R E A D THE S A F ETY
PRECAUTIONS

SECTION 3.

4.1) PREPARATION

(1) To ensure greatest accuracy, the pointer should be set exactly to the zero

position

by rotating the zero adjust screw (Fig 1).

(2) Make certain that the pointer lock button is in the open position (Fig. 1).

4.2) AC CURRENT MEASUREMENTS

WARNING

!

This instrument is designed to take current readings on circuits with a
maximum voltage above ground not exceeding 600 V ac. Using it on
circuits above 600 Vac poses a shock hazard to the user.

(1) Set the range switch to the highest 150 Aac range position.
(2)

Press the trigger to open the transformer jaws and clamp onto one conductor
onl

y (Fig. 2). Read the current directly on the scale. It is recommended that the

conductor be placed at the center of the closed jaws for maximum accuracy.

(3) When the reading is less than one third of the scale set the range switch to

the ne

xt lower ran ge position. For maximum accura cy, select the lo west

range possible without overranging the meter.

4.3) AC VOLTAGE MEASUREMENTS

WARNING

!

This instrument is designed to take voltage readings up to a maximum
of 60 0 Vac. Th e “C OM”termin al voltage sh ou ld not ex ce ed 500 V
measured to ground potential. Do not exceed these maximums.

(1) Insert the red te st lead into the “VOLT”t erminal of the instrument and the

black test lead into the “COM” terminal (Fig.3).

Pointer Lock

Zero Adjust

Wrong Corre

ct

Volt

Com

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6 Fig.7

Com

Ohm

Ohm Zero
Adj. Knob