GB KKT316 User Manual

Gardner

Bender

IMPORTANT: RECEIVING INSTRUCTIONS: Visually

inspect all components for shipping damage. If any
shipping damage is found, notify carrier at once.

Shipping damage is NOT covered by warranty. The
carrier is responsible for all repair or replacement costs
resulting from damage in shipment.

Instruction

Sheet

KKT316

KEYWAY

CUTTER

IMPORTANT—USER SAFETY AND PROTECTION: In setting up systems, take care to select the proper

components and design to ensure appropriate integration with your existing operations and equipment. Observe all
safety measures to avoid the risk of personal injury and damage to property and equipment through improper usage.

GB ELECTRICAL CANNOT BE RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY UNSAFE USE,
MAINTENANCE OR APPLICATION OF ITS PRODUCTS. Please contact GB's technical service department for
assistance if you are in doubt as to the proper safety precautions essential to designing and setting up your
particular application.

To prevent injury, keep hands away from
punches, dies and keyway cutting tools.

To avoid equipment damage and personal
injury, do not use the keyway cutting tool on
glass, plastic or wood. These materials
could shatter and produce splinters which
could cause injuries.

NOTE: To ensure smooth assembly, keep all
threads clean and lightly oiled.

When using the keyway cutter with a
hydraulic cylinder, be sure the cutting tool
is fully threaded into the cylinder pull rod to
avoid thread damage.

The keyway cutting tool is designed for use
with a 1” socket drive or a hydraulic
knockout cylinder. Do not use open end
wrenches, pliers or vise grip type tools
which can slip off the nut and cause damage
to the nut drive or personal injury.

!

CAUTION

DESCRIPTION

Keyway cutter tools are designed to punch a 3⁄16” slot in
steel panels up to 10-gauge. The cutter blade is 3⁄16” x 3⁄4”
long, SAE 01 tool steel. A pilot shoulder on the die
surface is 17⁄32” diameter and fits holes produced by a
1 7⁄32” knockout punch (KOM1732). The cutter tool can be
hand operated or attached to a hydraulic knockout
cylinder.

WARRANTY: GB ELECTRICAL, INC. warrants its
products against defects in workmanship and
materials for 1 year from date of delivery to user.
Chain is not warranted. Warranty does not cover
ordinary wear and tear, abuse, misuse, overloading,
altered products or use of improper fluid.

WARRANTY RETURN PROCEDURE: When
question of warranty claim arises, send the unit to the
nearest GB Authorized Service Center for inspection,
transportation prepaid. Furnish evidence of purchase
date. If the claim comes under the terms of our
warranty the Authorized Service Center will REPAIR
OR REPLACE PARTS AFFECTED and return the unit
prepaid.

PARTS AND SERVICE: For quality workmanship and
genuine GB ELECTRICAL parts, select an Authorized
GB Service Center for your repair needs. Only
repairs performed by an Authorized Service Center
displaying the official GB Authorized sign are backed
with full factory warranty. Contact GB Electrical
[phone] for the name of the nearest GB
Authorized Service Center.

REPAIR AND SERVICE INSTRUCTIONS: For repair service and parts contact your nearest GB ELECTRICAL
Service Center. The Service Center will provide complete and prompt service on all GB ELECTRICAL products.

GB Electrical, Inc.

An Applied Power Company

6101 N. Baker Road, Milwaukee, WI 53209
Phone: [phone] FAX [phone]

RPS-0059 Rev. A 03/07

Keyway Cutter with 1” Socket Wrench

1. Loosen the cutter jam nut, 2 or 3 turns. Insert the
cutting tool into the 17⁄32” panel opening until the pilot
shoulder extends into the hole and the die rests against
the panel. (Figure 2)

2. Hand tighten the jam nut to draw the cutter blade
against the panel. Position the alignment notch at the
location where the keyway is required.

3. Install a 1” socket and handle over the jam nut. Turn
the handle until the cutter blade makes a clean cut
through the panel. (Figure 3)

Maintenance

1. Keep all threads clean and lightly oiled to prevent rust
and enable smooth operation.

2. If keyway cutting blade becomes dull or damaged,
replace it immediately.

3. Keyway cutter replacement parts are available from
your closest GB Service Center.

Operation

Prior to using the keyway cutter, a 17⁄32” hole must be made
for the switch or component mounting (KOM1732).

Keyway Cutter Using Hydraulic Knockout Cylinder

1. Remove the punch and die from the punch cylinder.
Remove the cylinder pull stud.

2. Remove the large jam nut from the keyway cutter.

3. Thread the tool into the cylinder pull rod until the cutter
die rests against the cylinder.

4. Insert the cutter tool into the 17⁄32” panel opening until
the pilot shoulder fits into the hole and the die is
against the panel (Figure 1).

5. Turn the cutting tool until the alignment notch is located
where the keyway is desired.

6. Activate the hydraulic pump until the cylinder pulls the
cutter blade through the panel material.

Figure 2

Figure 1

Knockout
Cylinder

Panel

Alignment
Notch

Keyway
Cutter

Figure 3

Socket

Keyway
Cutter

Jam Nut

Alignment
Notch

Cutter Blade

Die