GB CS400 User Manual

IMPORTANT: RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any

shipping damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier
is responsible for all repair or replacement costs resulting from damage in shipment.

Gardner

Bender

Instruction

Sheet

IMPORTANT USER SAFETY AND PROTECTION: In setting up systems to fit your operations, care must

be taken to select the proper components and design to insure appropriate integration with your operations
and existing equipment and that all safety measures have been taken to avoid the risk of personal injury
and property damage from your application or system.

The CS400 Cylinder Support is used only with the
Ultra Eegor™ models B400L and B400DL when
mounting them on the BE400 Table Assembly.

Weight of the B400L Cylinder and
Frame is approximately 125 lbs. Make
sure help or equipment is available to
lift the unit 3 ft high.

1. The B400L and B400DL bender assembly is
mounted to the top of the BE400 table. Position
the bender on the table; make sure the cylinder
is at the wheel end of the table. Slide the conduit
support extension under the cylinder. Raise the
extension up to support the cylinder during
assembly installation. Figure 1.

2. Remove the double anchor pin. Push on the
cylinder assembly to slide the cylinder and block
forward. Align the block with the holes marked
4” - 3

1

⁄2”. Install the anchor pin. Figure 2.

3. Slide the front stabilizer bar over the side of the
table so the mounting bolts can be removed.
Leave the stabilizer in position. Move the cylinder
end of the bender to gain access to mounting
bolts connecting the round pads under the frame.
Remove each bolt. Position the lower frame and
pads over the holes in the table top.

GB ELECTRICAL, INC. CANNOT BE HELD RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY
UNSAFE USE, MAINTENANCE OR APPLICATION OF ITS PRODUCTS. Please contact GB's technical

service department for assistance if you are in doubt as to the proper safety precautions essential to
designing and setting up your particular application.

CS400

Cylinder Support

For Ultra EegorsTMB400L and B400DL

Fig. 1

Fig. 2

WARRANTY: GB ELECTRICAL, INC. warrants its
products against defects in workmanship and
materials for 1 year from date of delivery to user.
Chain is not warranted. Warranty does not cover
ordinary wear and tear, abuse, misuse, overloading,
altered products or use of improper fluid.

WARRANTY RETURN PROCEDURE: When question
of warranty claim arises, send the unit to the nearest
GB Authorized Service Center for inspection,
transportation prepaid. Furnish evidence of purchase
date. If the claim comes under the terms of our
warranty the Authorized Service Center will REPAIR
OR REPLACE PARTS AFFECTED and return the unit
prepaid.

PARTS AND SERVICE: For quality workmanship and
genuine GB ELECTRICAL parts, select an Authorized
GB Service Center for your repair needs. Only
repairs performed by an Authorized Service Center
displaying the official GB Authorized sign are backed
with full factory warranty. Contact GB Electrical
[phone] for the name of the nearest GB
Authorized Service Center.

REPAIR AND SERVICE INSTRUCTIONS: For repair service and parts contact your nearest GB ELECTRICAL
Service Center.The Service Center will provide complete and prompt service on all GB ELECTRICAL products.

GB Electrical, Inc.

An Applied Power Company

6101 N. Baker Road, Milwaukee, WI 53209
Phone: [phone] FAX [phone]

RPS-0130 Rev. A 03/07

4. Fasten the lower frame and stabilizer bar to the
table. Use two 1⁄2- 13 UNC x 13⁄4” long bolts
installed from the underside of the table. Do not
fully tighten the bolts. Figure 3 & 4.

5. Position the two legs of the cylinder support
under the cylinder end of the table. Align the
holes in the table and fasten the support,
mounting pads and lower frame with two

1

⁄2- 13

UNC x 1

3

⁄4” long hex head bolts.

6. Tighten all four bender-to-frame mounting bolts.

7. Adjust the cylinder support “V” block until the
cylinder is firmly supported and level. Figure 5.

Fig. 3

Fig. 5

Fig. 4