Gastroback 98101 User Manual

®

GASTROBACK

Instructions for use

Meat Grinder / Cookie Attachment

Accessory Design Stand Mixer Advanced

Art.-Nr. 98101

Read all provided instructions before first usage!

Model and attachments are subject to change

Carefully read all provided instructions before you start running the

appliance and pay regard to the warnings mentioned in these

!

instructions.

Important Instructions

• The appliance is designed for normal household quantities. Do not operate or store
the appliance outdoors or in damp or wet areas.

• Before use, always make sure that the appliance and accessory is properly and
completely assembled. Always IMMEDIATELY unplug the appliance after each operation
and before assembling or disassembling accessories. Always ensure, that the accessories
are engaged firmly before connecting the appliance to the mains power supply (see
´Operation`). Always handle the entire appliance and the tools with care and without
violence.

• Do not grab into the assembled attachment with your hands or any other objects
when the appliance is connected to the poweroutlet.

• CAUTION: Do not block the ventilation slits on the back of the appliance and do
not use the appliance in continuous operation for more than 10 minutes to avoid overheating.
If processing large quantities of food, regularly interrupt operation and unplug the
appliance for a few minutes, to let the motor cool down.

• ATTENTION: Avoid contact the moving parts. Keep hands, hair, clothing,

as well as spatula and other utensils, away from accessory during
operation to prevent injury and/or damage to the mixer or the attachment.

• DO NOT immerse the motor housing or power cord in any liquids or spill any
liquids on it.

• Never leave the appliance unattended when in operational mode.
Do not leave the appliance unattended while connected to the power supply. Always
switch ´Off` the appliance and IMMEDIATELY unplug the appliance after operation and
if it is not in use, cleaning and/or assembling or disassembling the processing tools.
Always grasp the plug to disconnect the appliance from the power outlet.

The Meat Grinder Attachment

10

9

8

7

3

1

1. spanner for the ring nut

2. ring nut

3. fine screen

4. coarse screen

5. scrape

6. scroll

7. housing

8. tray

9. food pusher

2

6

5

4

12

11

10. 2 litre storage container can be used as
dust protection while storing the
attachment or as meat tray when
processing meat.

11. cookie attachment holder

12. multi-shaped cookie blade

Meat Grinder Attachment
Operating

Before first use of the Meat Grinder Attachment

Remove all promotional materials and packing as well as any foreign objects, but do
not remove the model label. Before first use and after a long period of storage, clean
the processing tools in warm soapy water (see ´Care and Cleaning`).

Using the Meat Grinder Attachment

WARNING: Always switch ´Off` the appliance, wait until the motor stops completely

and unplug the appliance before assembling/disassembling the attachment. To turn the
appliance ´Off` you have to turn the speed control anticlockwise into the ´Off`-position.

Assemble the Meat Grinder Attachment

1. Take the housing into your left hand. The part with the
thread has to face the front and the feed chute has to
face upwards.

2. Take the scroll into your right hand and place it into the
housing. The axis has to face the housing when sliding the
scroll into the housing (picture A).

A

NOTE: The scroll is correctly located when the scroll is

pushed up all the way inside the housing and the end of
the axis pokes out of the back end of the housing.

3. Fit the scrape over the square end of the drive shaft
ensuring that it is correctly located. The rounded side of the
knife must face the scroll, the smooth side is in contact with
the screen (picture B).

NOTE: Meat will not be minced if the knife is mounted
the wrong way round.

IMPORTANT: Failure to correctly position the scrape over
the end of the drive shaft may cause permanent damage to
your attachment.

4. Select the desired screen and place against the scrape.
IMPORTANT: Make sure that the notch in the screen fits

over the protrusion of the housing (picture B/C). The
scrape does not flush 100 %with the rim of the housing
when correctly located.

B

protrusion

C

notch

5. Take the ring nut and screw it onto the thread of the housing
turning it clockwise. You can use the spanner to securely tighten
the ring nut (picture D/E).

NOTE: Do not tighten the ring nut too much to avoid overwinding
the thread.

The Meat Grinder Attachment is now assembled and can be
attached to the Design Standmixer Advanced.

D

6. Prop up the attachment access (picture F).

7. Press down the attachment ejector (picture G) and slide the
Meat Grinder Attachment into the opening. Release the attachment
ejector and turn the Meat Grinder Attachment slightly so that the
shaft engages in the socket with pin of the access opening located
in the hole of the attachment.

8. Place the tray cover on top of the feed chute in a convenient
position (picture H).

You can place the storage container beneath the outlet to collect
the food.

The Meat Grinder Attachment is now ready for use.

To operate the Meat Grinder Attachment
WARNING: For the case that liquid runs over the appliance

while operating turn the appliance ´Off` immediately and pull
the plug. Clean and dry the appliance according to the
instructions ´Care and cleaning`.

TIP: If you use special mince-recipes you can mix the ingredients
(for example steamed onions or spices) with the meat before
mincing. This way the ingredients get mixed really well.

E

F

G

IMPORTANT: The appliance can not mince hard or stingily

ingredients (for example: bones, nuts, ginger). If you use hard
ingredients like onions or carrots, you have to steam them before
adding them to the meet. Place a dry towel beside the appliance
to dry off overrunning liquids.

1. Cut the meat into pieces of 2,5 cm square size and remove
hard parts like bones, shells or stems.

2. Assemble the Meat Grinder Attachment as described, attach
it to the Design Standmixer Advanced and place a plate or dish
(for example the provided storage container) in front of the outlet.

H