Gastroback 98100 User Manual

®

GASTROBACK

Instructions for use

Pasta Attachment

Accessory Design Stand Mixer Advanced

Art.-Nr. 98100

Read all provided instructions before first usage!

Model and attachments are subject to change

Carefully read all provided instructions before you start running the

appliance and pay regard to the warnings mentioned in these

!

instructions.

Important Instructions

• The appliance is designed for normal household quantities. Do not operate or store
the appliance outdoors or in damp or wet areas.

• Before use, always make sure that the appliance and accessory is properly
and completely assembled. Always IMMEDIATELY unplug the appliance after each
operation and before assembling or disassembling accessories. Always ensure, that the
accessories are engaged firmly before connecting the appliance to the mains power
supply (see ´Operation`). Always handle the entire appliance and the tools with care and
without violence.

• Do not grab into the assembled attachment with your hands or any other objects
when the appliance is connected to the poweroutlet.

• CAUTION: Do not block the ventilation slits on the back of the appliance and do
not use the appliance in continuous operation for more than 10 minutes to avoid overheating.
If processing large quantities of food, regularly interrupt operation and unplug the
appliance for a few minutes, to let the motor cool down.

• ATTENTION: Avoid contact the moving parts. Keep hands, hair, clothing,

as well as spatula and other utensils, away from accessory during
operation to prevent injury and/or damage to the mixer or the attachment.

• IMPORTANT: Speed setting 3 is the highest speed setting you are allowed to
choose, when using the Pasta Attachment. Please note that dough made too dry or
fed through too quickly may cause your Pasta Attachment to break.

• DO NOT immerse the motor housing or power cord in any liquids or spill any
liquids on it.

• Never leave the appliance unattended when in operational mode.
Do not leave the appliance unattended while connected to the power supply. Always
switch ´Off` the appliance and IMMEDIATELY unplug the appliance after operation and
if it is not in use, cleaning and/or assembling or disassembling the processing tools.
Always grasp the plug to disconnect the appliance from the power outlet.

The Pasta Attachment

5

13

6

7

1

1. spanner for the ring nut

2. ring nut

3. spaghetti screen

4. scroll

5. tray

6. housing

7. macaroni screen

8. rigatoni screen

9. tagliatelle screen

2

3

4

12

10

10. lasagne screen

11. large macaroni screen

12. Cleaning tool

13. measuring cup (500 gr)

8

9

11

Pasta Attachment
Operating

Before first use of the Pasta Attachment

Remove all promotional materials and packing as well as any foreign objects, but do
not remove the model label. Before first use and after a long period of storage, clean
the processing tools in warm soapy water (see ´Care and Cleaning`).

Using the Pasta Attachment
WARNING: Always switch ´Off` the appliance, wait until

the motor stops completely and unplug the appliance
before assembling/disassembling the attachment. To turn
the appliance ´Off` you have to turn the speed control
anticlockwise into the ´Off`-position.

Assemble the Pasta Attachment

1. Take the housing into your left hand. The part with the
thread has to face the front and the feed chute has to
face upwards.

2. Take the scroll into your right hand and place it into the
housing. The axis has to face the housing when sliding the
scroll into the housing (picture A).

NOTE: The scroll is correctly located when the scroll is
pushed up all the way inside the housing and the end of
the axis pokes out of the back end of the housing.

3. Fit the desired pasta screen over the axis of the scroll
inside the housing (picture B). Ensuring that the pasta screen
is correctly located. The side of the screen with the round
hole in the middle must face the scroll, the side with the
number in the middle has to face the ring nut.

A

B

C

IMPORTANT: The pasta screen has two gaps which have

to fit into the corresponding lugs of the housing. If necessary
turn the screen a little bit to make it slide into the right position.

NOTE: The screen will not flush with the rim of the housing
when located in the right position.

4. Take the ring nut and screw it onto the thread of the
housing turning it clockwise (picture C). You can use the
spanner to securely tighten the ring nut (picture D).

D