Garmin 821P User Manual

Epson® PowerLite® 821p

Multimedia Projector

User’s Guide

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.

Trademarks

Epson is a registered trademark of Seiko Epson Corporation.

PowerLite, PrivateLine, and Presenters Club are registered trademarks; SizeWise is a trademark; and Epson
Connection, Epson Store, and Extra Care are service marks of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.

© 2005 by Epson America, Inc. 10/05

CPD-18615R1

2

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9

Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10

Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . 13

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting with the VGA Cable . . . . . . . . . . . . . . . . . 16

Connecting with a VGA-5BNC Cable. . . . . . . . . . . . . 18

Connecting the USB Cable for

Remote Mouse Control. . . . . . . . . . . . . . . . . . . . . 19

Connecting an External Monitor . . . . . . . . . . . . . . . . . 20

Playing Sound Through the Projector . . . . . . . . . . . . . 21

Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting a Composite Video Source . . . . . . . . . . . . 23

Connecting an S-video Source . . . . . . . . . . . . . . . . . . . 24

Connecting an RGB Video Source. . . . . . . . . . . . . . . . 25

Connecting a Component Video Source . . . . . . . . . . . 26

Playing Sound Through the Projector . . . . . . . . . . . . . 27

3

2 Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 30

Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 30

Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 32

What To Do If You See a Blank Screen . . . . . . . . . . . . . 33

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Focusing and Zooming Your Image. . . . . . . . . . . . . . . . 36

Adjusting the Height of Your Image . . . . . . . . . . . . . . . 37

Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 38

Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 39

Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 39

Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 39

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 41

3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 43

Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 44

Switching Between Picture Sources . . . . . . . . . . . . . . . . 44

Turning Off the Picture and Sound. . . . . . . . . . . . . . . . 45

Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Changing the Image’s Aspect Ratio . . . . . . . . . . . . . . . . 46

Using the Remote Control as a Wireless Mouse . . . . . . . . . . 47

Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4 Contents

4 Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 49

Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 50

Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 51

Adjusting Colors and Clarity . . . . . . . . . . . . . . . . . . . . . . . . 53

Adjusting the Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 57

Selecting Projector Setup Options . . . . . . . . . . . . . . . . . . . . 59

Viewing Lamp Usage and Other Information. . . . . . . . . . . . 61

Using the Projector’s Security Features . . . . . . . . . . . . . . . . 62

Creating Your Own Screen Logo . . . . . . . . . . . . . . . . . 63

Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Turning On the Password and User’s Logo . . . . . . . . . 65

Starting the Projector with a Password . . . . . . . . . . . . . 66

Disabling the Projector’s Buttons. . . . . . . . . . . . . . . . . 67

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . 68

5 Maintaining and Transporting

the Projector

Cleaning the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . 70

Cleaning and Replacing the Air Filter. . . . . . . . . . . . . . . . . 71

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . 75

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . 76

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

6 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

What To Do When the Lights Flash . . . . . . . . . . . . . . . . . 79

Solving Problems with the Image or Sound . . . . . . . . . . . . 81

Solving Password Problems . . . . . . . . . . . . . . . . . . . . . . . . 89

Solving Problems with the Remote Control . . . . . . . . . . . . 89

Solving Problems with the Projector’s Buttons . . . . . . . . . . 90

Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Telephone Support Services . . . . . . . . . . . . . . . . . . . . . 91

A Technical Specifications . . . . . . . . . . . . . . . . . . . . 93

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Mouse Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Contents 5

Safety and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . . 96

Compatible Computer Display Formats. . . . . . . . . . . . . . . . 97

B Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . 99

Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 101

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 102

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 103

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

6 Contents

-

Welcome

The Epson

®

Lite® 821p is a portable projector that offers up to 2600
ANSI lumens of brightness. From classrooms to boardrooms, your
full-color presentations and videos will be bright and visible even in
ordinary indoor lighting. With its whisper-quiet operation,
ease-of-use, and quick start up and shut down, the PowerLite 821p
ensures that your presentations come off without a hitch.
Additionally, its built-in speaker delivers powerful 5 watt audio,
making it perfect for presentations in large rooms.

Images are displayed at a native resolution of 1024 × 768 pixels. The

PowerLite 821p delivers accurate color, superior color saturation, and
incredibly vivid images and clear text. Support for S-video contributes
to theater-quality performance.

You can connect the projector to a wide range of computers, including

®

IBM

-compatible PCs and notebooks, Apple® Macintosh,® Power

®

Macintosh
computers, and many iMac
patented SizeWise

series (including G3, G4, and G5 systems), PowerBook®

®

and iBook® series systems. With Epson’s

™

technology, the projector supports computer

displays ranging from VGA through UXGA.

You can connect any of the following video sources: HDTV, VCR,

®

DVD player, gaming console (such as Microsoft

®

PlayStation

2, and Nintendo GameCube™), camcorder, digital

Xbox,™ Sony®

camera, or laser disc player. The PowerLite 821p supports NTSC,
PAL, and SECAM video formats.

You can connect up to four devices to the projector at the same time.
The source buttons let you easily switch among them, and a dedicated
audio port for each source lets you automatically switch sound when
you switch video. With the projector’s

Source Search button, you

don’t even have to identify your input source. Just press the button
repeatedly until you see the image you want on the screen.

7

To prevent unauthorized use of your PowerLite 821p, you can assign
a password, create a user logo which is displayed at startup to identify
the projector, and disable the projector’s buttons through the
Operation Lock feature. For more information about security features,
see page 62.

Getting the Most from Your Projector

Depending on your presentation, you can take advantage of any or all
of these options:

■ Connecting to a notebook or other computer

If you want to connect the projector to a notebook or desktop
computer, see page 16. For additional presentation control, you
can connect the USB cable to the projector for running slide
shows, and connect an external monitor to view the presentation
on your computer simultaneously.

■ Connecting to video sources

You can connect a DVD player, VCR, HDTV, camcorder, laser
disc player, digital camera, and other video sources to your
projector. See page 22 for instructions.

8 Welcome

■ Using the remote control

The remote control lets you switch from computer to video
sources, zoom in on part of your image, freeze or mute the
presentation, and adjust many other projector features. For
details, see Chapter 3.

By connecting the USB mouse cable included with your
projector, you can also use the remote control as a wireless mouse.
This lets you click through computer-based presentations (such as
PowerPoint

®

) from up to 20 feet away. For more information, see

page 47.

■ Including sound in your presentation

If your presentation includes sound, you can connect the audio
cable that came with your projector to use the projector’s built-in
speaker. See page 21.

Using Your Documentation

Your documentation includes a Quick Setup sheet, warranty
brochures, and Epson PrivateLine

The Quick Setup sheet gives instructions to quickly set up your
projector and connect it to a notebook, iBook, or PowerBook
computer.

This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:

■ Warnings must be followed carefully to avoid bodily injury.

■ Cautions must be observed to avoid damage to your equipment.

■ Notes contain important information about your projector.

Getting More Information

Need tips on giving presentations? How about quick steps for setting
up your projector? Here’s where you can look for help:

■ www.presentersonline.com

Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club

®

—and it’s free.

®

Support card.

■ built-in help system

Press the Help button on the remote control or projector to get
quick solutions for common problems. See page 77 for details.

■ support.epson.com

Download FAQs (frequently-asked questions) and e-mail your
questions to Epson support.

If you still need help after checking this User’s Guide and the sources
listed above, you can use the Epson PrivateLine Support service to get
help fast. Call [phone] and enter the PIN on your PrivateLine
Support card. See page 91 for more information.

Welcome 9

Registration and Warranty

Your projector comes with a basic carry-in warranty and an
international warranty that let you project with confidence anywhere
in the world. For details, see page 104 and the warranty brochure that
came with your projector.

In addition, Epson offers free Extra Care

SM

Road Service. In the
unlikely event of an equipment failure, you won’t have to wait for
your unit to be repaired. Instead, Epson will ship you a replacement
unit anywhere in the United States or Canada, usually via overnight
delivery. See the Extra Care Road Service brochure for details.

To register, complete the registration form that came with your
projector and mail it to Epson. Or register your product online at:

http://www.epson.com/webreg

Registering also lets you receive special updates on new accessories,
products, and services.

Unpacking the Projector

After unpacking the projector, make sure you have all these items:

Projector

Power cord VGA computer cable

10 Welcome

Remote control and batteries

Audio adapter

Documentation

USB cable

Save all packaging in case you need to ship the projector. Always use
the original packaging (or equivalent) when you need to send the
projector to another location.

Additional Components

Depending on how you plan to use the projector, you may need
additional components:

■ To receive an S-video signal, you need an S-video cable. One is

usually provided with your video device, or you can purchase it
from Epson. See page 12.

■ To receive a component video signal from a VCR or other video

device, you need a D-sub, 15-pin, VGA-to-component video
cable, which is available from Epson. See page 12.

■ Some older PowerBooks and Macintosh desktop models may

need the Macintosh adapter set shown on page 17 (available from
Epson; see page 12). Older iMac systems may need a special
adapter to provide a VGA output port; see your computer dealer.

Welcome 11

note

To purchase a replacement
remote control, call
[phone] (U.S.) or
[phone] (for dealer
referral in Canada).

Optional Accessories

To enhance your use of the projector, Epson provides the following
optional accessories:

Product Product number

Replacement lamp V13H010L30

Air filter replacement set V13H134A06

®

Samsonite

ATA molded hardshell case ELPKS51

Component video cable
S-video cable

Macintosh adapter set ELPAP01

Distribution amplifier ELPDA01

wheeled soft case ELPKS35

ELPKC19
ELPSV01

50-inch portable screen
60-inch portable pop-up screen
80-inch portable pop-up screen

83.6-inch hanging pull-down screen

Image presentation camera
High resolution document camera

®

Kensington

Ceiling mount
False ceiling plate
Suspension adapter
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel

security lock ELPSL01

ELPSC06
ELPSC07
ELPSC08
ELPSC09

V12H162020
V12H064020

ELPMB36
ELPMBFCP
ELPMBAPL
ELPMBSEC
ELPMBACC

You can purchase these accessories from your dealer, by calling
Epson at [phone], or by visiting the Epson Store

SM

at www.epsonstore.com (U.S. sales only). In Canada, please call
[phone] for dealer referral.

12 Welcome

Setting Up the Projector

This chapter tells you how to set up the projector and connect it to a

computer or video source. You can connect up to four devices
simultaneously: four video sources, one computer and three video
sources, or two computers and two video sources.

You’ll find instructions for the following in this chapter:

■ Positioning the projector

■ Connecting to a computer

■ Connecting to video sources

1

13

Positioning the Projector

Before connecting the projector, you
need to decide where to place it. If
you’re setting up the projector yourself
and it isn’t already installed in the
room you’re using, you’ll probably
want to place it on a table in front of
the screen, as shown.

This lets you stand in the front of the room, face the audience, and
remain close enough to the equipment to be able to control it. Try to
leave as much space as possible between the projector and the screen to
get a good-size image.

Place the projector somewhere between 3 and 48 feet from the screen.
Use the figure below to help you determine exactly how far. Image size
increases with distance, but can vary depending on how you’ve
adjusted the optical zoom and other settings.

note

You can download the
Projection Distance
Calculator program from
the Drivers & Downloads
link for your projector at

http://support.epson.com.

14 Setting Up the Projector

29.8 to 48.3 feet 5.8 to 9.5 feet 2.8 to 4.7 feet

Also keep these considerations in mind:

■ Place the projector on a sturdy, level surface.

■ Make sure there is plenty of space for ventilation around and

under the projector. Do not set the projector on top of loose
papers that could block the vents under the projector.

■ Make sure the projector is within 6 feet of a grounded electrical

outlet or extension cord.

Try to place the projector directly in front of the center of the screen,
facing the screen squarely. If the projector isn’t positioned this way,
the image will be “keystone” shaped, instead of square or rectangular.

If you place the projector below the level of the screen, you’ll have to
tilt it up by extending the front adjustable foot, as described on
page 37. This also causes the image to lose its rectangular shape, but
the Auto Keystone feature corrects the distortion automatically. If the
image does not regain its rectangular shape, the tilt angle is greater
than 15° or the Auto Keystone feature may have been disabled. To
turn it on, see page 58. To adjust it manually, see page 38.

Other Installations

You can also project from behind the screen or from the ceiling, with
the projector mounted upside-down:

Rear projection (using a
translucent screen)

Rear/ceiling projection (using
a translucent screen)

note

The Auto Keystone feature
corrects vertical distortion
automatically. For more
information, see page 38.

Front/ceiling projection

To project from overhead, you’ll need the optional ceiling mount
hardware. (See page 12 for ordering information.) You’ll also need to

Front/Ceiling or Rear/Ceiling for the Projection option in the

select
Extended menu. To project from the rear, select

Rear. See page 59 for

more information.

Setting Up the Projector 15

Connecting to a Computer

note

If you have an iBook with
an RCA video-out port,
follow the instructions for
connecting to a video device
on page 23.

note

You cannot connect your
computer to the projector
using only a USB cable. To
receive signals from the
computer, you must connect
it with the VGA cable that
came with your projector or a
VGA–5BNC cable.
Connecting the USB cable
lets you use the remote control
as a wireless mouse.

You can connect the PowerLite projector to any computer that has a
standard VGA or BNC monitor port, including PC notebook
computers, Macintosh PowerBooks and iBooks, and hand-held
devices. You can connect two computers at the same time.

Follow the instructions in this section to:

■ Connect the projector to your computer with the VGA cable

included with the projector.

■ Connect the projector to your computer with a

commercially-available VGA–5BNC cable.

After connecting the projector to your computer, you may also
want to:

■ Connect the USB cable that came with your projector so that you

can use the remote control as a wireless mouse; see page 19.

■ Connect a monitor to the projector so you can view your

presentation close-up as well as on-screen (not necessary if you’re
using a notebook); see page 20.

■ Connect a commercially-available computer audio cable to play

computer audio; see page 21.

16 Setting Up the Projector

Connecting with the VGA Cable

Follow these instructions to connect to your computer with the VGA
cable that came with your projector. Before you start, make sure your
computer and the projector are turned off.

1. If you are connecting the projector to a desktop computer,

disconnect the monitor cable from your computer.

2. Locate the VGA computer cable that

came with the projector.

VGA computer cable

3. Connect one end of the cable to the projector’s

Computer1/Component Video1 or the
Computer2/Component Video2 port. If you are going to

connect your computer monitor to the projector for simultaneous
display, use the

Computer1/Component Video1 port.

4. Connect the other end of the cable to your computer’s video-out
or monitor port.

If you’re using a PowerBook or iBook and you can’t connect the
cable, you may need to use the Macintosh desktop adapter as
shown below (available from Epson; see page 12).

To use the adapter, remove its cover as
shown and set its DIP switches according
to the resolution you want to use, such as
16-inch mode. See your Macintosh
documentation for instructions.

Replace the cover and connect the
adapter to the free end of the computer
video cable. Then plug the cable (with
the adapter) into the video port on your
Macintosh.

5. Tighten the screws on the connectors.

If you want to view the display simultaneously on your computer
monitor and the projector screen, see “Connecting an External
Monitor” on page 20.

Setting Up the Projector 17

VGA-5BNC cable

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
button on the projector or the

Comp1 or Comp2 button on the

Source Search

remote control. See page 32.

Connecting with a VGA-5BNC Cable

If your computer provides video output through BNC connectors,
follow these instructions to connect the projector to your computer
with an optional VGA-5BNC cable. Before you start, make sure your
computer and the projector are turned off.

1. Disconnect the monitor cable from your computer.

2. Connect the cable’s VGA connector to the projector’s

Computer1/Component Video1 or the
Computer2/Component Video2 port. If you are going to

connect your computer monitor to the projector for simultaneous
display, use the

Computer1/Component Video1 port.

18 Setting Up the Projector

3. Connect the BNC connectors to your computer’s BNC ports.

4. Tighten the screws on the VGA connector.

If you want to view the display simultaneously on your computer
monitor and the projector screen, see “Connecting an External
Monitor” on page 20.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
button on the projector or the

Comp1 or Comp2 button on the

Source Search

remote control. See page 32.

Connecting the USB Cable for Remote Mouse Control

Using the remote control as a wireless mouse lets you click through
slideshow-style presentations, such as PowerPoint, from up to 20 feet
away. This makes it easy to deliver your presentation, since you won’t
need to stand near your computer.

To use the wireless mouse function, your system must have a USB
port and the full version of one of these operating systems:

Windows

Windows 98SE, 2000, Me, or XP Macintosh OS 8.6 to 9.2, OS X

1. If you are using a desktop computer, disconnect the mouse cable

®

from your computer.

Macintosh

note

You cannot connect your
computer to the projector
using only a USB cable. To
receive signals from the
computer, you must connect it
with the VGA cable that came
with your projector or a
VGA–5BNC cable.
Connecting the USB cable lets
you use the remote control as a
wireless mouse.

For details about using the
remote control as a wireless
mouse, see page 47.

2. Locate the USB mouse cable that came with the projector and
connect the square end of the cable to the projector’s USB
port.

Setting Up the Projector 19

note

Some LCD monitors may
not be able to display the
image correctly. If you have
trouble displaying the
image, connect a multiscan
monitor. Also, make sure the
computer’s refresh rate is set
to 65 Hz or greater.

You cannot display video
images or configuration and
help menus on an external
monitor.

3. Connect the flat end of the cable to any available USB port on
your computer.

4. If necessary, configure your notebook to work with an external
mouse.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

Connecting an External Monitor

If you want to see your presentation close-up as well as on the
projection screen, you can connect an external monitor to the
projector. This lets you view images on your computer monitor while
the projector is in standby mode (plugged in but not turned on) and
check your presentation or switch between picture sources even if
you’ve pressed the
projection on the screen.

Simultaneous display is possible only when the computer is connected
to the projector’s

Make sure the projector and computer are off. Then connect the
monitor’s cable to the projector’s

A/V Mute button on the remote control to turn off

Computer1/Component Video1 port.

Monitor Out port, as shown:

20 Setting Up the Projector

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

Playing Sound Through the Projector

Your computer probably has its own sound system; however, it may
not be adequate for your presentation. If you need more volume, you
can connect a computer audio cable to take advantage of the
projector’s built-in speaker. You can obtain a computer audio cable
(3.5-mm stereo miniplug cable) from a computer or electronics dealer.

1. Connect one end of the audio cable to the

Audio1 jack on the

projector.

2. Connect the other end of the audio cable to your notebook’s
headphone jack or audio-out jack, or your desktop’s

speaker or audio-out port.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

note

If you’ve connected two
computers to the projector,
you can play sound from
both. Connect the audio
cable for the computer
connected to the

Computer 2/Component
Video 2
Audio 2 jack on the

projector. Connect the other
end of the cable to the second
computer.

When you switch sources,
the projector automatically
plays sound from the new
source.

connector to the

Setting Up the Projector 21

note

The projector does not
support TV antenna cable
F connectors. However, you
can project TV images if you
use a VCR as a tuner.

Connecting to Video Sources

You can connect a DVD player, VCR, camcorder, laser disc player,
digital camera, gaming console—such as Microsoft Xbox, Sony
PlayStation 2, or Nintendo GameCube—or any other compatible
video source to your projector. You can connect up to four video
devices at one time.

The projector supports HDTV, SDTV, NTSC, PAL, and SECAM,
and automatically detects the video format. It can receive composite
video, S-video, RGB video, and component video. The type of cable
you need depends on the video source:

■ For composite video, use a commercially-available RCA A/V

cable. See page 23.

■ For S-video, use the S-video cable supplied with your video device

or order one from Epson. See page 24.

■ For RGB video, use the VGA computer cable included with the

projector. See page 25.

■ For component video, you’ll need a component video cable. You

can purchase one from Epson; see page 26.

22 Setting Up the Projector

After connecting your video device to the projector, you may want to
connect an audio cable to play sound from your video equipment
through the projector’s built-in speaker. See page 27 for instructions.

Connecting a Composite Video Source

If you’re connecting a composite video device, use a
commercially-available RCA A/V cable. Before starting, make sure the
projector and your DVD player or other video source are turned off.

1. Connect the yellow RCA plug on one end of the cable to the

projector’s yellow

2. Connect the yellow plug on the other end of the cable to the

video-out port on your video source.

Video jack as shown below.

3. To play sound through the projector, follow the instructions

beginning on page 27.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to the projector, select

Video as

the input source after projection starts. See page 32 for details.

Setting Up the Projector 23

Connecting an S-video Source

If your video source has an S-video jack, you can use it to project a
higher quality video image. You’ll need an S-video cable, which is
usually provided with your video source, or you can purchase one
from Epson. See page 12 for ordering information.

Before starting, make sure the projector and your DVD player or
other video source are turned off.

1. Insert one end of the S-video cable into the projector’s

S-Video

port and the other end into the S-video output port of your video
source.

2. To play sound through the projector, follow the instructions
beginning on page 27.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to the projector, select

S-Video

as the input source after projection starts. See page 32 for details.

24 Setting Up the Projector

Connecting an RGB Video Source

Follow these instructions to connect the projector to a video player or
satellite receiver that has an RGB video output port using the VGA
computer cable that came with the projector.

Before starting, make sure the projector and your DVD player or
other video source are turned off.

1. Connect one end of the VGA computer cable to the

Computer1/Component Video1 or the
Computer2/Component Video2 port on the projector.

2. Connect the other end to the video port on your player.

3. To play sound through the projector, follow the instructions
beginning on page 27.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to the projector, select

Computer 1 (RGB) or Computer 2 (RGB) as the source, depending

on which port you used. See page 32 for details.

Setting Up the Projector 25

Connecting a Component Video Source

If your video source has component video connectors, you can use
them to project a higher quality video image. You’ll need a
component video cable (ELPKC19), which can be purchased from
Epson. See page 12 for ordering information.

Before starting, make sure the projector and your DVD player or
other video device are turned off.

1. Connect the large end of the component video cable to the
projector’s

Computer2/Component Video2 port.

Computer1/Component Video1 or the

26 Setting Up the Projector

2. Insert the three ends of the component video cable into the

R, G, and B ports on your video source.

3. To play sound through the projector, follow the instructions
beginning on page 27.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

If more than one device is connected to your projector, select

Computer 1 (Component Video) or Computer 2 (Component
Video)

as the source, depending on which port you used. See page 32

for details.

Playing Sound Through the Projector

The projector has a built-in speaker with a maximum output of 5 W.
You can play sound from your video equipment through the
projector’s speaker if your video device has an audio output port.

For RCA-Style Audio Output Ports

Most video devices have an RCA-style audio output port. In this case,
use the audio adapter supplied with the projector to connect the
projector to a commercially-available A/V cable, as shown below:

1. Locate the audio adapter that came with your projector.

2. Connect the black audio plug on one end of the adapter to the

Audio jack corresponding to your video source. For example, if

you’ve connected your video device to the projector’s
connect the adapter to the

Audio jack next to it.

Video port,

3. Connect the red and white plugs on the other end of the adapter
to the red and white plugs on the A/V cable.

4. Connect the red or white plug on the other end of the A/V cable
to the corresponding color-coded audio output port on your
video source.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

Audio adapter

note

Each input port has its own
dedicated audio input jack.
To play sound from a source,
you must connect the audio
cable to the correct audio
input jack.

When you switch the video
source, the projector
automatically plays sound
from the new source.

Setting Up the Projector 27

For Stereo Mini-Jack Audio Output Ports

Some video devices, especially camcorders, may have a stereo
mini-jack audio output port. In this case, use a commercially-available
stereo mini jack audio cable to connect to the projector, as shown
below:

note

Each input port has its own
dedicated audio input jack.
To play sound from a source,
you must connect the audio
cable to the correct audio
input jack.

When you switch the video
source, the projector
automatically plays sound
from the new source.

1. Connect one end of the audio cable to the

Audio jack

corresponding to your video source. For example, if you’ve
connected your video device to the projector’s
connect the adapter to the

Audio jack next to it.

S-Video port,

2. Connect the other end to your video device’s audio output port.

If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 30 for instructions.

28 Setting Up the Projector

Projecting

Once you’ve set up the projector, you’re ready to turn it on, adjust

the image, and give your presentation.

Although you can operate the projector without it, the remote control
lets you use additional features. See Chapter 3 for instructions on
using the remote. This chapter covers the following:

■ Turning on the projector and other equipment

■ Adjusting the image

■ Adjusting the volume

■ Shutting down the projector

1

29

caution

Do not use the projector with
the lens cap in place. The
heat generated by the lamp
can damage it.

Turning On Your Equipment

Make sure your projector and other equipment are set up and
connected correctly, as described in Chapter 1. Then turn on your
projector, as described below.

If you turn on your connected computer or video equipment before
starting the projector, the projector automatically detects and displays
the image source. If you turn on the projector first, or have multiple
pieces of connected equipment, you may have to select the image
source manually. See page 32.

Turning On the Projector

Follow these steps to plug in and turn on the projector:

1. Push in the tabs and remove the lens cap.

30 Projecting

2. Connect one end of the power cord to the projector’s power inlet.

3. Connect the other end to an electrical outlet.

Power light on top of the projector turns orange, indicating

The
that the projector is receiving power but not yet turned on. Wait
until the light stops flashing but stays orange.

4. Turn on your computer or video source if you have not already.

5. Press the P
(You can also press the P

Power button on top of the projector to turn it on.

Power button on the remote control.)

Power button

note

If you are using the remote
control for the first time, be
sure to insert the batteries as
described on the Quick
Setup sheet.

If the Direct Power ON
feature has been enabled (as
described on page 60), you
don’t need to press the

P

Power button to turn the

projector on. Just plug the
projector into an electrical
outlet. When the
light stops flashing and stays
green, the projector is ready to
use.

Power

Projector

The projector beeps and the

Power light flashes green as the

Remote control

projector warms up. The projector lamp comes on in a few
seconds. When the

Power light stops flashing, you’re ready

to start.

6. If you don’t see your image, press the

Source Search button on

the projector or remote control repeatedly until you see it.

(Windows only: If you see a message saying that Windows has
found a plug-and-play monitor, click

Cancel.)

7. If you are prompted to enter a password, see page 66.

To focus and adjust the image, see page 35. If a projected image fails
to appear even after you press the

Source Search button, see “What

To Do If You See a Blank Screen” on page 33.

warning

Never look into the lens when
the lamp is on. This can
damage your eyes, and is
especially dangerous for
children.

Projecting 31

note

The name of the selected
image source appears in the
upper right corner of the
screen.

When you’re done with your presentation, shut down the projector as
described on page 41. Shutting down the projector correctly prevents
premature lamp failure and possible damage from overheating.

Selecting the Image Source

If you have only one device connected to the projector, the projector
should detect it automatically. If you have more than one device
connected (for example, if you’ve connected both a computer and
DVD player), you may have to switch between image sources. If you
don’t see the image you want, press one of the following buttons on
the remote control:

■ Comp 1

Press this button to move through the following options:

Computer 1 (Auto), Computer 1 (RGB), and Computer 1
(Component Video)

■ Comp 2

Press this button to move through the following options:

Computer 2 (Auto), Computer 2 (RGB), Computer 2
(Component Video)

.

.

32 Projecting

■ S-Video

Press to select S-Video.

■ Video

Press to select Video.

You can also press the

Source Search button on the remote control

or projector repeatedly until the correct image is projected. If a
projected image fails to appear, see the next section for help.

Once you see your image, turn to page 35 for instructions on focusing
and making other image adjustments.

What To Do If You See a Blank Screen

If you see a blank screen or a blue screen with the message No Signal
after turning on your computer or video source, try the following:

■ Make sure the cables are connected correctly, as described in

Chapter 1.

■ Make sure the Power light is green and not flashing and the lens

cap is off.

■ Make sure you’ve selected the correct image source; see page 32.

Allow a few seconds for the projector to sync up after pressing the
button.

■ Check the Signal menu to make sure the correct input source is

selected. See page 55.

If you’re using a PC notebook:

■ Hold down the Fn key and press the function key that lets you

display on an external monitor. It may have an icon such as
or it may be labelled
projector to sync up after pressing it. Check your notebook’s
manual or online help for details.

CRT/LCD. Allow a few seconds for the

On most systems, the or

CRT/LCD key lets you toggle

between the LCD screen and the projector, or display on both at
the same time.

■ If you’re projecting from a notebook and you don’t see the same

image on the projection screen and computer screen, check your
monitor settings to make sure both the LCD screen and the
external monitor port are enabled.

From the Control Panel, open the

Settings tab, then click Advanced. The method for adjusting

the settings varies by brand; you may need to click a

Display utility. Click the

Monitor tab,

then make sure the external Monitor port is set as your primary
display and/or enabled. See your computer’s documentation or
online help for details.

Projecting 33

If you’re using a Macintosh with OS X:

You may need to set up your system to display on the projector screen
as well as the LCD screen. Follow these steps:

1. From the Apple menu, select

System Preferences, then click

Displays.

2. Select VGA Display or Color LCD, click Arrangement or

Arrange, and make sure Mirror Displays is checked.

Click here

Select Mirror
Displays

If you’re using a Macintosh with OS 9.x or earlier:

You may need to set up your system to display on the projector screen
as well as the LCD screen. Follow these steps:

1. From the Apple menu, select

Monitors or Monitors and Sound.

2. Click the Arrange icon.

Control Panels, then click

34 Projecting

Click here

Drag one
monitor icon on
top of the other

3. Drag one monitor icon on top of the other.

If the Arrange option isn’t available, you may need to select one of
the Simulscan resolution settings:

1. Click the

Click here

2. Select a

Monitor icon, if necessary.

Select a
Simulscan
resolution

Simulscan resolution, as shown. (Allow a few seconds

for the projector to sync up after making the selection.)

Adjusting the Image

Once you see your image, you’ll need to make certain adjustments:

■ To focus or zoom your image, see the next section.

■ If the image is too high or too low, you can reposition it.

See page 37.

■ If the image isn’t square, see page 38.

■ To adjust image brightness, see page 39.

■ If a computer image displays incorrectly, see page 39.

■ To change the color mode for your image and surroundings, see

page 39.

You can make many other adjustments to the image—such as
changing the brightness, contrast, and aspect ratio—using the
projector’s menu system. See Chapter 4 for more information.

Projecting 35

Focusing and Zooming Your Image

Rotate the focus ring to sharpen the image.

Focus ring

Rotate the zoom ring to reduce or enlarge the image.

Zoom ring

36 Projecting

You can also change the image size by moving the projector closer to
or farther away from the screen. You can use the

E-Zoom buttons on

the remote control to zoom in on a portion of the image. See page 45
for instructions.

Adjusting the Height of Your Image

If the image is too low, you can raise it by extending the projector’s
front adjustable foot.

1. Stand behind the projector. Press up on the blue foot release
lever and lift the front of the projector to extend the front
adjustable foot.

2. Once the image is positioned where you want, release the lever to
lock the foot in position.

Foot

3. To fine-tune the height of the image,
rotate the feet at the back of the
projector.

If the image is no longer rectangular after
raising it, see the next section.

Projecting 37

Pointer button

Enter button Menu buttton

note

You can also use the buttons
on the projector to access the
menu system:

Menu button ESC button

Adjusting the Image Shape

The projector automatically corrects images that are distorted when
the projector is tilted up or down (up to a 15° tilt). The Keystone
window appears on the screen while the projector makes the
correction. If the projected image still isn’t rectangular or has a
“keystone” shape, do one or more of the following:

■ If your image looks like or , you’ve placed the

projector off to one side of the screen, at an angle. Move it directly
in front of the center of the screen, facing the screen squarely.

■ If your image looks like or , the Auto Keystone feature

may have been disabled or you may need to manually adjust the
keystone correction value. (Auto Keystone is not available when
you’re using ceiling or rear projection.) Follow the directions
below:

■ To turn on Auto Keystone, press the Menu button on the

remote control. Use the pointer button on the remote
control (or the arrow buttons on the projector) to select the

Setting menu, then press Enter. If Auto Keystone is OFF,

use the pointer button to highlight this option and press

Enter. Select ON in the Auto Keystone window that appears

and press
pressing the

■ To manually adjust the keystone correction value, press the

the image. After correction, your image will be slightly
smaller.

Enter to save your changes. Exit the menu by

Menu button.

or buttons on the projector to correct the shape of

Enter button Arrow buttons

38 Projecting

You can also make keystone adjustments using the projector’s Setting
menu. See page 58.

Adjusting the Brightness

The brightness of an image depends on the source you are projecting
and the amount of light in the room. If the image is too bright or not
bright enough, here are two ways you can adjust it:

■ Change the Brightness setting in the Image menu. See page 54.

■ Select Low or High for the Brightness Control option in the

Setting menu. (See page 58.) Low brightness mode extends the
life of the lamp and decreases the fan noise.

Correcting Computer Images

If you’ve connected a computer and the image doesn’t look right, or it
doesn’t fit properly on the screen, press the
remote control or the

Enter button on the projector to automatically

Auto button on the

reset the projector’s tracking, sync, resolution, and position settings.
(You must be projecting an image for this button to have any effect.)
The screen turns black for a few seconds, and then the image appears
again. After the image reappears, it takes about three seconds for the
correction to take effect. Don’t press any other buttons while this is
happening.

Adjusting the Color Mode

You may want to adjust the color mode to select a setting that is
appropriate for the image you’re projecting and the environment in
which you’re projecting it.

If you’re projecting computer or RGB video images, the default color
mode is
bright rooms. For other images, the default color mode is
which optimizes video images using natural colors.

Presentation, which is appropriate for presentations in

Dynamic,

note

If the Auto Setup option in
the Signal menu is enabled,
the projector automatically
corrects computer images.
Normally you don’t have to
press the
page 56 for details.

Auto button. See

Color Mode button

Auto button

Projecting 39

The following table lists the six color modes available.

Color mode Description

Dynamic Best for projecting movies with vivid color in bright

rooms. This is the default mode for projecting from
video devices other than RGB video.

Presentation Use when you’re projecting a presentation in a bright

room. This is the default mode when you’re projecting
from a computer or RGB video device.

Theatre Use when projecting movies in a dark room.

Living Room Best for playing video games or watching TV in a

bright room.

sRGB Use when projecting computer or video images

conforming to the sRGB color standard. Make sure
your computer or video device signal is also set to
sRGB.

Blackboard Choose this fixed color mode when you need to

project against a green blackboard. Lets images retain
their natural tints.

40 Projecting

To change the color mode, press the

Color Mode button on the

remote control until you see the mode you want. The currently
selected setting appears in the upper right corner of the screen. You
can also use the projector menu system to change the color mode in
the Image menu (see page 54).

Adjusting the Volume

You can use the buttons on the remote control or projector to increase
or decrease the volume for the projector’s built-in speaker or external
speakers connected to the projector. Press the button to increase
the volume, or the button to decrease it. A volume gauge appears
on the screen while the volume is being adjusted.

note

You can also adjust the
volume using the projector’s
Setting menu. See page 57
for details.

Volume controls

Shutting Down the Projector

When you’ve finished using the projector, follow the recommended
procedure to shut it down. This extends the life of the lamp and
protects the projector from possible overheating.

1. If you’re using a computer, shut it down first.

2. To turn off the projector, press the P
projector or remote control.

You see this confirmation message:
(If you don’t want to turn it off, press
any other button or wait a few
seconds until it disappears.)

Power button on the

You must adjust the volume
separately for each input
source.

caution

Never unplug the
projector without first
turning it off, as described
in this section. If the
Direct Power ON feature
has been enabled (as
described on page 60),
you must still follow the
steps in this section to turn
the projector off.

Projecting 41

note

When the projector has not
received any input signals for
30 minutes, it automatically
turns off the projector lamp
and enters “sleep mode.” This
conserves electricity, cools the
projector, and extends the life
of the lamp. If you are done
using the projector, unplug
the power cord. If you want
to start projecting again, press
the P

Power button. You

can turn sleep mode on or off
through the Extended menu.
See page 59.

caution

To avoid damaging the
projector or lamp, never
unplug the power cord
when the Power light is
green or flashing orange.

3. Press the P

Power light flashes orange for about 20 seconds as the projector

Power button again. The lamp turns off, and the

cools down. When the projector has cooled, it beeps twice to
indicate that power is off. The

Power light stays orange and the

exhaust fan shuts off.

If you want to turn the projector on again, wait until the orange
light stops flashing. Then press the P

Power button.

4. Press up on the blue foot release lever and lower the projector to
retract the front adjustable foot, as shown.

5. Replace the lens cap and unplug the power cord.

6. Turn off and disconnect any equipment plugged into the
projector.

42 Projecting

note

Avoid sunlight and
fluorescent light, as these may
interfere with signal
reception.

13

Using the Remote Control

The remote control lets you access your projector’s features from

anywhere in the room—up to 20 feet away. For example, you can turn
the projector on and off, freeze the presentation, zoom in on a portion
of your image, and access the menu system. (The projector menus let
you adjust many projector settings; see Chapter 4.)

If you’re using a computer and you’ve connected the mouse cable
as described in Chapter 1, you can use the remote control as a wireless
mouse.

When using the remote control, stand within 20 feet of the projector.
Point the remote control either at the front or back of the projector or
at the screen (the projector’s front sensor can detect signals bounced
off the screen). Press the button for the function you want to use.

This chapter covers the following information:

■ Controlling the picture and sound

■ Using the remote control as a wireless mouse

■ Replacing the remote control batteries

43

Controlling the Picture and Sound

You can use the remote control to select your source, temporarily turn
off the picture and sound, freeze the action, or zoom in on the picture.
Make sure you have set up your projector and connected any
equipment as described in Chapter 1.

Switching Between Picture Sources

Select a source

Moves through all the
input sources in sequence

If you’ve connected your projector to more than one computer and/or
video source, you can use the buttons on the remote control to switch
between the different sources.

■ Press the Comp1 button to select the computer or video source

connected to the projector’s

Computer1/Component Video1

port.

■ Press the Comp 2 button to select the computer or video source

connected to the projector’s

Computer2/Component Video2

port.

■ Press the S-Video button to select a video source connected to the

projector’s

■ Press the Video button to select a video source connected to the

projector’s

■ Press the Source Search button to move successively through all

S-Video port.

Video port.

of the input sources.

After you select a source, the screen goes dark for a moment before the
image appears. The name of the selected source (such as
or

S-Video) appears briefly on the screen.

Computer1

44 Using the Remote Control

Turning Off the Picture and Sound

Press the A/V Mute button on the remote control to turn off the
image and sound and darken your screen. This is useful if you want to
temporarily re-direct your audience’s attention without the distraction
of a bright screen.

■ To turn off the picture and sound, press the A/V Mute button.

The screen goes dark.

■ To turn the image and sound back on, press the button again, or

Esc.

press

You can create an image, such as a company logo or a picture, to
display on the screen whenever you press the

A/V Mute button. See

page 63 for more information.

Stopping Action

Press the Freeze button to stop the action in your video or computer
image and keep the current image on the screen. The sound will
continue, however. Also, because the source continues to transmit
signals, you won’t resume the action from the point you paused it.

ESC

Zoom in

Zoom out

Press the

Freeze button again or press Esc to restart it.

Zooming Your Image

Follow these steps to zoom in on a portion of the image:

1. Press the

You see a crosshair indicating the center of the zoom-in area.

2. Use the pointer button to position the crosshair in the area you
want to enlarge.

3. Continue pressing the
area up to 4 times.

E-Zoom button on the remote control.

E-Zoom button to enlarge the selected

FreezeA/V Mute

Using the Remote Control 45

4. While the image is enlarged, you can:

■ Use the pointer button to pan about.

■ Press the E-Zoom button to zoom out.

note

You must be projecting
component, composite, or
S-video images to change the
aspect ratio.

You can also change the
aspect ratio using the
projector’s Signal menu. See
page 55 for details.

5. When you’re done, press the

ESC button to return to the original

size.

Changing the Image’s Aspect Ratio

If you’re projecting a widescreen format image, you can use the

Resize button on the remote control to change the aspect ratio.

Follow these steps:

1. Press the
for widescreen format.

2. Press it again to return to 4:3 aspect ratio.

Resize button once to change the aspect ratio to 16:9

46 Using the Remote Control

Using the Remote Control as a Wireless Mouse

When you use the remote control as a wireless mouse, you can control
your computer or click through slideshow-style presentations (such as
PowerPoint) from up to 20 feet away. This gives you more flexibility,
since you don’t need to stand near your computer to change slides.

To control your computer with the remote, make sure you have
connected the USB cable as described on page 19.

■ To display the mouse pointer, press the Pointer button.

■ To move the pointer on the screen, aim the remote at the screen

and use the pointer button.

■ To click (or left-click), press the Enter button.

■ To right-click, press the Esc button.

■ To double-click, press the Enter button twice.

■ To click and drag, press down and hold the Enter button and use

the pointer button to move where you want to drag.

■ To advance slides in a PowerPoint presentation in Slide Show

mode, press the
Press the

Page up or Enter button on the remote control.

Page down or Esc button to go back a slide.

Left-click or
double-click

pointer

Move the
pointer

Right-clickDisplay the

Page UpPage Down

Using the Remote Control 47

note

The remote control
automatically shuts off when
it detects a button being
pressed more than 30 seconds.
This conserves battery life. It
can be helpful, for example,
when the remote is in a
carrying case and the

P

Power button is

accidentally pushed.

caution

When replacing batteries,
take the following
precautions:

■ Replace the batteries as

soon as they run out. If a
battery leaks, wipe away
battery fluid with a soft cloth.
If fluid gets on your hands,
wash them immediately.

■ Do not expose batteries to

heat or flame.

■ Dispose of used batteries

according to local regulations.

■ Remove the batteries if you

won’t be using the remote
control for a long period of
time.

Replacing the Batteries

The remote control uses two AAA alkaline batteries. Follow these
steps when you need to replace them:

1. Press in the tab to remove the battery cover.

2. Remove the old batteries, then insert the new ones as shown.

3. Replace the battery cover. (It should click into place.)

48 Using the Remote Control

Fine-tuning the Projector

You can use the Menu button on the projector or remote control to

access on-screen menus to adjust the image, sound, and other features.
This chapter covers the following information:

■ Using the menu system

■ Adjusting image colors and clarity

■ Adjusting the input signal

■ Customizing projector features

■ Selecting projector setup options

■ Viewing lamp usage and other information

■ Using the projector’s security features

433

■ Restoring the default settings

49

Using the Projector’s Menu System

The six projector menus let you adjust and customize the projector
features:

■ The Image menu lets you modify the colors of the projected

image and fine-tune brightness, contrast, and sharpness.

■ The Signal menu lets you make adjustments to the input signal.

You can select your input source, change the image position and
aspect ratio, and adjust tracking and sync for computer images.

■ The Setting menu lets you customize the way you use the

projector. It allows you to adjust the volume and keystone
correction, set lamp brightness to high or low, select the shape of
the mouse pointer, and disable buttons on the projector while you
are projecting.

■ The Extended menu lets you customize the way you set up the

projector. Among the options, you can select the menu language,
set rear or ceiling projection, and record a custom image or logo
to be displayed as the startup screen or whenever you press the

A/V Mute button on the remote control.

50 Fine-tuning the Projector

■ The Info menu provides information about lamp status and

computer or video settings.

■ The Reset menu lets you restore the projector’s factory default

settings.

Changing Menu Settings

Use the buttons on the remote control to access the menus and change
settings. Follow these steps:

1. Press the

Menu button on the remote control or projector to

display the menu screen:

Menu options

Menus

The six menus are listed on the left, and the options available for
the highlighted menu are shown on the right.

2. Use the pointer button on the remote control or the up and
down arrow buttons on the projector to scroll through the menu
list. When you’ve highlighted the desired menu, press the

Enter

button to select it.

Menu button Esc button

Enter button

Arrow buttons

Pointer button

The highlight moves to the first option for that menu.

3. Use the pointer button or the up and down arrow buttons to
scroll through the list of options. (The options available depend
on which source is selected.)

Esc buttonEnter button

Fine-tuning the Projector 51

4. After highlighting the option you want to adjust, use the
pointer button on the remote control or left or right arrow

buttons on the projector to change the setting. In some cases, you
may have to press the

Enter button to see a sub-screen for

changing the setting.

■ Press the left or right side of the pointer button or the left

or right arrow buttons on the projector to adjust a slider bar.

■ To select from two or more settings, use the pointer

button or arrow buttons to highlight the desired setting, then
press

Enter.

5. Press the

Esc button to return to the previous menu or to close

the menu system if you are at the main menu. Your changes are
saved automatically.

6. Press the

Menu button to exit the menu system.

52 Fine-tuning the Projector

Adjusting Colors and Clarity

The Image menu lets you make adjustments to the colors of the
projected image and fine-tune brightness, contrast, and sharpness.
The options available depend on which image source is selected:

Computer (analog-RGB) and RGB video

Component, composite, and S-video

Follow these steps to adjust the appearance of your image:

1. Press the

2. Press

Menu button. You see the main menu.

Enter to select the Image menu.

Fine-tuning the Projector 53

note

You can also select High or

Low brightness mode in the

Setting menu. See page 58.

3. Use the pointer button (or the up and down arrow buttons)

and press

■ Color Mode

Enter to select any of the following options:

Corrects the vividness of image color. You can select from the
following six settings, and save a different one for each
computer and/or video source:

Dynamic: For projecting movies or playing video games in

vivid color in a bright room (the default when projecting
component, composite, and S-video images).

Presentation: For presentations in bright rooms (the default

when projecting computer or RGB video images).

Theatre: For optimizing movie images with natural color in a

dark room.

Living Room: For playing video games and watching TV in

a bright room.

sRGB: For standard sRGB computer displays.

Blackboard: Fixed color mode for projecting against a green

blackboard.

■ Brightness

Lightens or darkens the overall image.

■ Contrast

Adjusts the difference between light and dark areas.

54 Fine-tuning the Projector

■ Color Intensity (component, composite, and S-video)

Adjusts the depth or intensity of the image colors.

■ Tint (component, composite, and S-video)

Adjusts the balance of green to magenta in the image.

■ Sharpness

Sharpens or softens the image.

■ Color Adjustment

Adjusts the temperature and intensity of red, green, and blue.

4. When the image is set correctly, press

Esc or Menu. Your settings

are automatically saved.

Adjusting the Input Signal

Although the projector normally detects and optimizes the input
signal automatically, you can use the Signal menu to make manual
adjustments. In addition to changing the position of the projected
image, you can correct tracking and sync for computer images, or
change the aspect ratio to widescreen format for video images.

1. Press the

2. Select the

Computer (analog RGB) and RGB video

Component video

Menu button. You see the Image menu.

Signal menu. You see one of the following screens:

Composite video and S-video

Fine-tuning the Projector 55

note

y

If Auto Setup is turned off,

ou can still automatically
adjust tracking and sync for
computer images by pressing
the

Auto button on the

remote control or the
button on the projector’s
control panel.

If you have repositioned your
computer image with the

Position setting or made

changes to the

Sync settings, you can press

the

Auto button on the

remote control to restore the
default settings.

If you’re adjusting tracking
and sync manually, adjust
tracking first for best results.

Enter

Tracking or

3. Press

Enter. Then use the pointer button (or up and down

arrow buttons) and the

Enter button to select any of the

following options:

■ Auto Setup (computer images)

Leave this setting

ON to automatically optimize the computer

image. Turn it off if you want to adjust tracking and sync
manually.

■ Tracking (computer images)

Removes unwanted vertical lines from a computer image by
matching the projector’s internal clock to various computer
signals. See page 87 for more information about adjusting the
tracking.

■ Sync (computer images)

Corrects fuzziness or screen flicker by synchronizing the
projector with the tracking signal sent from the computer.
See page 87 for more information about adjusting the sync
setting.

■ Position

Use the pointer button or arrow buttons to move the
image on the screen left, right, up, or down.

■ Computer 1 Input

Selects the signal from equipment connected to the

Computer1/Component Video1 port. If your image colors

look wrong, try changing this setting from
following:

Component Video 1 for component video sources.

or

Computer 1 for computer or RGB video sources,

Auto to one of the

56 Fine-tuning the Projector

■ Computer 2 Input

Selects the signal from equipment connected to the

Computer2/Component Video2 port. If your image colors

look wrong, try changing this setting from
following:

Component Video 2 for component video sources.

or

Computer 2 for computer or RGB video sources,

Auto to one of the

■ Video Signal (composite and S-video)

Leave this setting at
system (select

■ Resize (video)

Auto unless you are using a 60-Hz PAL

PAL60).

Sets the image’s aspect ratio (ratio of width to height) to
for letterbox video content and to

16:9 for widescreen video

content.

4:3

4. When you’re finished adjusting the signal settings, press

Menu.

Esc or

Customizing Projector Features

The Setting menu lets you customize the way you use the projector,
from adjusting lamp brightness and speaker volume to changing the
shape of the mouse pointer.

1. Press the

2. Select the

Menu button.

Setting menu.

Fine-tuning the Projector 57

note

If your image is still distorted
after you perform keystone
correction, decrease the

Sharpness setting in the

Image menu.

To cancel the Operation
Lock function from the
projector, press the
button for about seven
seconds.

Enter

3. Press

Enter. Then use the pointer button (or up and down

arrow buttons) and the

■ Keystone

Adjusts a distorted image from a trapezoid shape to
rectangular. (The corrected image will be smaller.)

■ Auto Keystone

Automatically adjusts a distorted image from a trapezoid
shape to rectangular when the projector’s foot is extended or
retracted. (Not available when you’re projecting from the
ceiling or using rear projection.) Select

■ Operation Lock

When turned on, this function disables all projector buttons
except the P
effect after you restart the projector. (After you turn off the
projector, wait for the
before turning it on again.)

■ Pointer Shape

Lets you select from three different pointer shapes.

■ Brightness Control

Select Low lamp brightness when the projection is too bright
for the room. The
consumption and fan noise. Select
maximum brightness. (Also check the
the Image menu; see page 54.)

Enter button to set the following options:

ON or OFF.

Power button. Changes to this setting take

Power light to turn a steady orange

Low setting also reduces electricity

High to project the

Brightness setting in

58 Fine-tuning the Projector

■ Volume

Adjusts the volume for the projector’s speaker.

4. When you’re finished, press

Esc or Menu.

Selecting Projector Setup Options

Use the Extended menu to customize the way you set up the
projector. You can configure the projector for rear and/or ceiling
projection, change the language for the menus and messages, set the
screen background color, capture and store a custom image or logo for
the startup screen, and set up the projector for network use.

1. Press the

2. Select the

Menu button.

Extended menu. You see the features and their settings

on the right side:

3. Press

Enter. Then use the pointer button (or the up and down

arrow buttons) and the

■ Display

Message:

Background Color: Sets the screen background to Black,
Blue, or Logo when the A/V Mute button is pressed.

Startup Screen: Enables or disables display of the startup

screen when the projector is turned on. Either the Epson logo
or your own logo (if you’ve created one, as described on
page 63) appears.

■ User’s Logo

Let’s you record your own user’s logo. See page 63 for more
information.

Enter button to set the following options:

Lets you turn screen messages on or off.

note

The Startup Screen option
must be turned on if you
want to display a user’s logo.

A user’s logo cannot be created
and the
option cannot be turned off if
the
feature has been turned on.
See page 65.

Startup Screen

User’s Logo Protect

Fine-tuning the Projector 59

note

When Direct Power
is turned on, turn the
projector off as you would
normally. See page 41 for
instructions.

When

Direct Power is

enabled, it’s a good idea to
unplug the projector after
turning it off. Otherwise the
projector will turn on
automatically when power is
restored after a power failure.

■ Projection

Projector is in front of the screen.

Front:

Front/Ceiling: Projector is in front of the screen, mounted

upside-down from the ceiling.

Rear: Projector is behind the screen.

Rear/Ceiling: Projector is behind the screen, mounted

upside-down from the ceiling.

■ Operation

Direct Power:

When this feature is enabled, projection starts

as soon as you plug in the power cord. You don’t have to
press the P

Sleep Mode: When this feature is enabled, the projector

Power button.

lamp automatically turns off when the projector has not
received any input signals for 30 minutes. This conserves
electricity, cools the projector, and extends the life of the
lamp. To resume projecting, press the P

■ Standby Mode

Power button.

Set to Network ON to monitor your projector over a
network and perform other network functions when the
projector is in standby mode.

60 Fine-tuning the Projector

■ COM Port

Normally you don’t have to change this setting. Both USB

RS-232C let you use the remote control as a wireless

and
mouse.

RS-232C is also used for ASCII control codes and to

control the projector from a computer with the EMP
Link 21L software, which can be downloaded from

www.support.epson.com. If you change the setting, turn

the projector off and then on again to enable it.

■ Language

Select the language to be used for projector menus and
messages.

4. When you’re finished, press

Esc or Menu.

Viewing Lamp Usage and Other Information

Use the Info menu to view information about the display settings of
your computer and the number of hours the lamp has been used.

1. Press the
the following menus:

Computer (analog RGB, digital RGB, RGB
Video/Component video

■ Lamp Hours

Menu button and select the Info menu. You see one of

Video (Composite video, S-Video)

Displays the number of hours the lamp has been used. The
life span of the lamp ranges from about 2000 hours in
brightness mode to about 3000 hours in

Low brightness

High

mode. If the number shown is close to 2000 or the
information is displayed in red, make sure you have a spare
lamp handy.

note

You can make changes to
many of the signal settings on
the Signal menu. See page 55
for details.

note

The lamp usage timer doesn’t
register until you’ve used the
lamp for at least 10 hours.

■ Source

Displays the input source currently being projected.

■ Input Signal (computer, RGB video, and component video)

Displays the input signal setting.

■ Resolution (computer, RGB video, and component video)

Displays the input resolution.

■ Video Signal (composite and S-video)

Displays the video signal format.

Fine-tuning the Projector 61

■ Refresh Rate (computer, RGB video, and component video)

Displays the refresh rate.

■ Sync Info (computer, RGB video, and component video)

Provides information that may be needed by the service
technician.

2. When you’re finished, press

Esc or Menu.

Using the Projector’s Security Features

To prevent unauthorized use of the projector, you can do the
following:

■ Create an identifying user logo that is displayed at startup and/or

when the

■ Assign a password; this can be disabled for a set period if you want

to loan the projector to someone

■ Disable the projector’s buttons; this is useful, for example, if

you’re projecting in a classroom and you want to ensure that no
one touches the projector’s buttons while you’re using the remote
control

If you create a user’s logo for the projector, you can lock the logo on so
it is displayed as the startup screen and/or AV/Mute screen.
Unauthorized users cannot turn it off or change it. This feature is
intended to discourage theft and provides a way to identify the
projector should it be stolen.

A/V Mute button is pressed

62 Fine-tuning the Projector

If you assign the projector a password, a screen appears requesting the
password whenever the projector is turned on. If you enter the
password incorrectly three times in succession, the projector’s
operation is locked and you’ll need to disconnect the power cord, then
reconnect it to redisplay the password screen. If you enter the
incorrect password 30 times in succession, the projector is locked and
you’ll need to contact Epson to unlock it. See “Where To Get Help”
on page 91.

If someone else will be using the projector for awhile but you want to
make sure that person returns it by a certain time, you can temporarily
disable the password for a set period. When that time has elapsed, the
password is reactivated and must be entered before the projector can
be used.

When you enable the Operation Lock feature, all of the projector’s
buttons are disabled except the P

Power button.

Creating Your Own Screen Logo

You can transfer any image on your computer to the projector, and
then use it as the startup screen and/or the screen that is displayed
when you press the A/V Mute button. The image can be a company
logo, slogan, photograph, or any other image you want to use. The
projector considers this image the “User’s Logo.”

note

If you enable the password
before you set one and you
see the prompt to enter the
password, enter the default
password 0000 to proceed.

Follow these steps to capture the image and transfer it to the projector:

1. Display the image you want to use on the projector. You can use
an image from either a computer or video source, such as a VCR.

2. Press the

Menu button and select the Extended menu.

note

If the User’s Logo Protect
option is ON, you see a
message that the logo cannot
be recorded. You’ll need to
disable the

Protect

can create or change the
user’s logo. See page 65.

Fine-tuning the Projector 63

User’s Logo

option before you

3. Use the pointer button (or the down arrow button) and press

Enter to select User’s Logo.

4. When you see a message asking if you want to use the present
image as a user’s logo, select

Yes and press Enter. A selection box

displays over the image.

5. Use the pointer button on the remote control or the arrow
buttons on the projector to select the area of the image you want
to use. Once you have selected the area, press

Enter.

note

The default setting for the

Startup Screen option in

the

Display menu is ON. If

the

Startup Screen is set to

OFF, the logo will not

display at startup.

If the

User’s Logo Protect

option has been set to
the

Background Color

setting cannot be changed.
You need to turn the protect
function off first. See page 65
for details.

Once you’ve saved a user’s
logo, you cannot reset the logo
setting to its factory default
(no logo).

ON,

6. When you see the message
press

Enter. If you want to change the area selected, select No,

press

Enter and repeat steps 4 through 6.

Select this image?, choose Yes and

7. When you see this screen, select a zoom rate (display size), and
then press

8. When you see the message

Yes and press Enter. Saving the logo takes a few seconds. Do not

Enter.

Save image as user’s logo?, select

use the projector or other sources (computer, video, etc.) while
the logo is being saved.

9. When you see the message

Completed, press Esc.

10. To display the logo as the background screen when the A/V Mute
button is press, select the

11. Select

Background Color and press Enter. Then select Logo and

Enter.

press

Display menu and press Enter.

64 Fine-tuning the Projector

12. When you’re finished, press

Menu to exit the menus.

Setting a Password

1. Press the Freeze button on the remote control for about 5 seconds
until you see the Password Protect menu:

note

If a password has already
been set, you see the
Password Protect Release
screen. See “Starting the
Projector with a Password”
on page 66.

2. Select

3. Select

4. Hold down the

Password and press Enter. You see the message Change

the password?

Yes and press Enter.

Num key on the remote control and use the

numeric keypad to enter a 4-digit password.

The password will be displayed as

****. After you enter the last

digit, a confirmation screen appears. Enter the password again.

5. After you finish setting the password, press the

Esc button to

return to the Password Protect menu.

Make a note of the password and keep it in a safe place in case you
forget it.

Turning On the Password and User’s Logo

1. To enable the password, press the Freeze button on the remote
control for about 5 seconds until you see the Password Protect
menu

2. Select

Power ON Protect and press Enter.

Hold down this button to
activate the numeric
keypad

3. Select

ON and press Enter. Then press Esc.

Use these buttons like a
numeric keypad to enter
the password

Fine-tuning the Projector 65

note

If you make a mistake
entering the time, press the

Esc button and enter the

time again.

4. If you want to disable the password temporarily, select
press

Enter. Then hold down the Num button while you use the

numeric keypad to enter the number of hours (from 0 to 9999)
that you want the password feature disabled. If you want the
projector to request the password every time it is turned on, set
the timer to

0H. Press Enter when you’re done.

The countdown for the elapsed time begins as soon as you close
the Password Protect menu. (You can check the elapsed time in
this menu next to

Time elapsed.)

Timer and

5. To enable your screen logo, select

Enter. Select ON and press Enter.

User’s Logo Protect and press

When this feature is on the logo appears whenever the projector is
turned on (if the

Startup Screen is enabled in the Extended

menu; see page 59) and as the A/V Mute screen (if you selected
the

Logo as the Background Color in the Extended menu).

None of the User’s Logo features can be changed when the User’s
Logo Protect function is enabled.

6. Press

Menu to close the Password Protect menu.

If you lose the remote control, you will not be able to enter the
password, so keep the remote control in a safe place at all times.

When the period defined in the
the password is entered correctly, the elapsed time will be reset to

Time-elapsed setting has passed, and

0

and the countdown will start again. Remember to disable or change
this setting when you need to.

Starting the Projector with a Password

When the password function is enabled, you see this screen when you
turn on the projector:

66 Fine-tuning the Projector

Press down the Num button on the remote control as you use the
numeric keypad buttons to enter the password. Once you have
entered the password correctly, the password screen closes, and
projection begins.

If the password is not correct, you see the message

Please try again.

succession, you see the message

locked. Request code xxxxx

If you enter an incorrect password three times in

The projector’s operation will be

and the projector switches to standby

Wrong password.

mode for approximately 5 minutes. Write down the request code.
Then disconnect the projector’s power cord from the electrical outlet,
reconnect it, and turn the projector back on.

When you see the Password Protect Release screen again, you can try
to enter the correct password.

If you have forgotten the password, contact Epson with the request
code number that appears in the Password Protect Release screen for
assistance. See “Where To Get Help” on page 91.

If you enter an incorrect password 30 times in succession, the
projector remains locked and you must contact Epson to unlock it.

Disabling the Projector’s Buttons

When you enable the Operation Lock function, all the projector’s
buttons are disabled except for the P

1. Press the

2. Select the

Menu button.

Setting menu and press Enter.

Power button.

note

To cancel Operation Lock,
press the projector’s
button for seven seconds.

Enter

3. Use the pointer button (or up and down arrow buttons) to
select

Operation Lock and press the Enter button.

4. Select

5. Select

6. Press the

ON and press Enter.

Yes and press Enter to confirm the setting.

Menu button.

Fine-tuning the Projector 67

note

The input signal, Video

Signal, User’s Logo, and
Language settings do not

return to their defaults when
you select
the input signal or video
signal, use the
on the Signal menu; see
page 55 for details. To reset
the

Language settings, use

the
Extended menu; see page 59
for details.

Reset All. To reset

Reset option

User’s Logo and

Reset option on the

Restoring the Default Settings

The Reset menu lets you return most projector menu settings to their
default values. It also lets you reset the lamp hours to their inital
default value; see page 75 for instructions on resetting the lamp timer.

To reset most projector menu settings, select

Enter button to display the confirmation screen. Select Yes to reset all

the default settings or

No to cancel.

Reset All and press the

68 Fine-tuning the Projector

warning

Before you clean any
part of the projector,
turn it off and unplug
the power cord. Never
open any cover on the
projector, except the
lamp and filter covers.
Dangerous electrical
voltages in the projector
can injure you severely.
Do not try to service
this product yourself,
except as specifically
explained in this User’s
Guide. Refer all other
servicing to qualified
service personnel.

5

Maintaining and Transporting the Projector

Your projector needs little maintenance. All you need to do on a

regular basis is keep the lens clean. Any dirt or smears on the lens may
show up on your projected image.

You also need to periodically clean the air filter and the air intake and
exhaust vents. A clogged air filter or air vent can block ventilation
needed to cool the projector and cause overheating.

The only parts you should replace are the lamp and air filter. If any
other part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

■ Cleaning the lens

■ Cleaning the projector case

■ Cleaning and replacing the air filter

■ Replacing the lamp

■ Resetting the lamp timer

■ Transporting the projector

69

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface.

■ Use a canister of compressed air to remove dust.

caution

The lens is easily
damaged. Do not use
glass cleaner to clean
the lens. Never rub
the lens or use paper
or rough material to
clean it. Handle the
projector carefully to
avoid subjecting the
lens to shocks.

■ To remove dirt or smears on the lens, use lens-cleaning paper. If

necessary, moisten a soft cloth with lens cleaner and gently wipe
the lens surface.

Cleaning the Projector Case

Before you clean the case, first turn off the projector and unplug the
power cord.

■ To remove dirt or dust, wipe the case with a soft, dry, lint-free

cloth.

■ To remove stubborn dirt or stains, moisten a soft cloth with water

and a mild detergent. Then wipe the case.

■ Do not use wax, alcohol, benzene, paint thinner, or other

chemical detergents. These can damage the case.

70 Maintaining and Transporting the Projector

Cleaning and Replacing the Air Filter

Clean the air filter and air intake and exhaust vents on the bottom and
rear of the projector after every 100 hours of use. If they are not
cleaned periodically, they can become clogged with dust, preventing
proper ventilation. This can cause overheating and damage the
projector. When the filter and vents are clogged, the projector displays
the message

The projector is overheated.

To clean the air filter and air vents, follow these steps:

1. Press the P

Power button twice to turn off the projector. When

you hear the projector beep twice, unplug the power cord.

2. Clean the air vent on the back of the projector.

3. Carefully turn the projector upside-down and clean the filter and
air intake vents on the base of the projector.

To clean the filter and air vents, Epson recommends using a small
vacuum cleaner designed for computers and other office
equipment. If you don’t have one, gently clean them using a very
soft brush (such as an artist’s brush).

Air vent

Air vents

note

You may also need to clean
the vents and filter if the

Temp light on top of the

projector is red or flashing
orange. See page 80 for
details about the projector
lights.

Air filter

If the dirt is difficult to remove or if the filter is torn or bent,
replace it. Contact your dealer or call Epson at [phone] to
obtain a new one. The air filter set (part number V13H134A06)
contains two filters. In Canada, please call [phone] to
locate a dealer.

Maintaining and Transporting the Projector 71

4. If you need to replace the filter, slide it off, as shown.

p

5. Align the new filter carefully as you slide it into place. It should
click into place.

note

You can check to see how
many hours the lamp has
been used. See page 61.

Turn the projector off when
not in use. Continuous
24-hour-a-day use may
reduce the overall life of this

roduct.

72 Maintaining and Transporting the Projector

Replacing the Lamp

The projection lamp typically lasts for about 2000 hours of use
(in high brightness mode) or 3000 hours (in low brightness mode). It
is time to replace the lamp when:

■ The projected image gets darker or starts to deteriorate.

■ The lamp light is flashing orange.

■ The message Replace the Lamp appears on the screen when the

lamp comes on. Replace the lamp as soon as possible. If you
continue to use the lamp after you see this message, there is a
greater possibility of the lamp breaking.

Contact your dealer or call Epson at [phone] in the United
States for a replacement lamp. Request part number V13H010L30.
In Canada, please call [phone] to locate a dealer.

Follow these steps to replace the lamp:

1. Press the P

Power button twice to turn off the projector. When

you hear the projector beep twice, unplug the power cord.

2. If the projector has been on, allow it to cool down for at least an
hour (or until the lamp is cool).

3. Use the screwdriver that came with the lamp to loosen the screw
holding the lamp cover.

4. Slide the cover out, then lift it off.

warning

Let the lamp cool before
replacing it. If the lamp
breaks, handle the shards
carefully to avoid injury.

caution

Never touch the lamp with
your bare hands. The
invisible residue left by the oil
on your hands may shorten
the lamp life. Use a cloth or
gloves to handle the new
lamp.

5. Use the screwdriver to loosen the two screws holding the lamp in
place. (You can’t remove the screws.)

Maintaining and Transporting the Projector 73

note

The lamp(s) in this
product contain mercury.
Please consult your state and
local regulations regarding
disposal or recycling. Do not
put in the trash.

caution

Do not touch the glass
portion of the lamp assembly.
Touching the glass could
result in premature lamp
failure.

6. Hold the lamp as shown and pull it straight out.

7. Gently insert the new lamp. If it doesn’t fit easily, make sure it’s
facing the correct way.

8. Once the lamp is fully inserted, tighten its screws.

9. Lower the lamp cover into place. (The opening should be almost
covered, and the top of the cover should be flush with the top of

note

Be sure to seat the lamp fully
and secure the lamp cover. If
the lamp is not properly
installed or the cover is loose,
the lamp will not turn on.

the projector.) Then slide the cover closed and tighten the screw.

10. Reset the lamp timer as described in the next section.

74 Maintaining and Transporting the Projector

Resetting the Lamp Timer

You must reset the lamp timer after replacing the lamp to clear the

Replace the Lamp warning message. Follow these steps:

1. Connect the power cable and turn on the projector.

2. Press the
select the

3. Select the

Menu button on the remote control or projector and

Reset menu. Then press Enter. You see the following:

Lamp-Hours Reset option and press Enter. You see

the following:

note

Do not reset the lamp timer if
you have not replaced the
lamp. If you do, the

Hours will not accurately

reflect the number of hours
that the lamp has been used.

Lamp

Esc button

4. Select

5. Press

Yes and press Enter.

Esc to return to the main menu or the Menu button to exit

the menu system.

Enter button Menu buttton

Menu button Esc button

Enter button

Maintaining and Transporting the Projector 75

note

Epson shall not be liable for
any damages incurred during
transportation.

Transporting the Projector

The projector contains many glass and precision parts. If you need to
transport it, please follow these packing guidelines to prevent damage
to the projector:

■ When shipping the projector for repairs, use the original

packaging material if possible. If you do not have the original
packaging, use equivalent materials, placing plenty of cushioning
around the projector.

■ When transporting the projector as freight or checked luggage,

first put it in a carrying case, then pack it in a firm box, using
cushioning around the case.

76 Maintaining and Transporting the Projector

Solving Problems

This chapter helps you solve problems with your projector, and tells

you how to contact technical support for problems you can’t solve
yourself. This chapter explains the following:

■ Using the projector’s on-screen help system

■ What to do when the projector’s status lights flash

■ Solving problems with the image or sound

■ Solving password problems

■ Solving problems with the remote control

■ Solving problems with the projector’s buttons

■ Contacting technical support

6

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can
get help by pressing the
control. The following choices are available:

■ Problems with image

■ Problems with sound

■ Problems with [Source Search]

■ Language change

? Help button on the projector or remote

77

Press to
return to the
last menu

Press to confirm
selection

Use to select
a problem or
solution

Help button

Follow these steps to get help:

1. Press the

? Help button on the remote control or projector. You

see the help menu.

Press to confirm selection

Press to return
to the last menu

Help button

Press one of these buttons
to select a problem or solution

2. Use the pointer button on the remote control or the up and
down arrow buttons on the projector to select an option. Then
press the

Enter button to select it.

3. Use the pointer button on the remote control or the up and
down arrow buttons on the projector to highlight the problem
you want to solve. Then press the

Enter button to view the

solution(s).

78 Solving Problems

4. Highlight a solution (if this choice is available). Then press the

Enter button to select the solution.

Press the

Esc button if you need to back up.

If the solution is to adjust one of the settings, use the pointer
button on the remote control or the left and right arrow buttons
on the projector to adjust it.

5. To exit the Help system, press the

? Help button.

If none of the suggestions solves your problem, see additional
solutions to problems in the following sections.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status and
let you know when a problem occurs.

Power light

Lamp light

Temperature light

If the projector is not working correctly, first turn it off and unplug it.
Then plug the power cord back in and turn on the projector. If this
does not solve the problem, check the status lights on top of the
projector and try the solutions recommended in the following table.

Solving Problems 79

Power
light

Red Flashing red Flashing red There is an internal error in the projector. Turn the

Red Off Flashing red There is a problem with the fan or a sensor. Turn

Red Flashing red Off The lamp is burned out, broken, or not installed

— Flashing orange Off Replace the lamp with a new one as soon as

Red Off Red The projector has overheated and turned itself

Lamp
light

Temperature
light Description

projector off and unplug it. Contact Epson for
help.

the projector off and unplug it. Contact Epson for
help.

correctly; or the lamp cover is open. Close the
cover or replace or reseat the lamp, if necessary,
as described on page 72. If these suggestions
don’t work, contact Epson.

possible; see page 72 for instructions. If you
continue to use the lamp, there is a risk it may
break.

off. Let it cool for about five minutes, then turn it
back on. Make sure there is plenty of space
around and under the projector for ventilation.
Also clean the air filter and air exhaust vents. See
page 71. If it continues to overheat, you may
need to replace the air filter.

Flashing red Off Flashing orange The projector is too hot. Make sure the

temperature in the room does not exceed 95
(35 °C) and there is plenty of space around and
under the projector for ventilation. Clean the air
filter and air vents, if necessary. See page 71 for
instructions.

Orange Off Off The projector is in standby or sleep mode. You

can unplug it or press the P Power button to
turn it on.

Flashing
green

Green Off Off The projector is operating normally.

Flashing
orange

Off Off The projector is warming up. Wait for the image

to appear.

Off Off The projector is cooling down. Wait for the light

to stop flashing and remain orange before
unplugging it.

°F

80 Solving Problems

Solving Problems with the Image or Sound

Power does not turn on.

■ Make sure the power cable is connected. Also, connect a lamp to

your power outlet to make sure it’s working.

■ If the projector lights turn off and on when you touch the power

cable, the cable may be defective. Contact Epson as described on
page 91.

No image appears on the screen.

■ Check that the Power light is green, not flashing, and the lens

cap is off.

■ Make sure that the projector is securely connected to your

computer or video source.

■ The projector may be in standby or sleep mode. If the projector

has not received any input signal for 30 minutes, it turns off the
lamp to conserve the lamp life and save energy. If the
is orange, press the P

Power button to turn the projector on.

Power light

■ Press the A/V Mute button to make sure the picture has not been

turned off temporarily.

■ If the power was switched off and then on again, the projector

may still be cooling down. Wait until the
flashing and remains orange; then press the P

Power light stops

Power button

again.

■ Check the Video Signal or Computer 1 Input or Computer 2

Input

setting in the Signal menu to make sure it is correct for the

selected source. See page 55 for more information.

■ Have messages been turned off in the Display setting of the

Extended menu? See page 59 for details.

■ Adjust the Brightness setting on the Image menu or select High

for the

Brightness Control setting in the Setting menu. See

page 54 or page 58.

Solving Problems 81

■ The attached computer may be in sleep mode or displaying a

black screen saver. Try pressing a key on the computer.

■ If you’re projecting from a video source, press the Play button on

your video equipment.

Nothing appears on the external monitor.

■ Make sure the VGA computer cable is connected to your

computer’s video port and the projector’s

Computer1/Component Video1 port. It will not work if you

connected the computer cable to the projector’s

Computer2/Component Video2 port.

■ Make sure the cable from your monitor is connected to the

projector’s

Monitor Out port.

You see a blue screen with the message No Signal displayed.

■ Make sure the cables are connected correctly, as described in

Chapter 1.

■ Make sure the power to your computer or video source is

turned on.

82 Solving Problems

■ If you’ve connected a computer and one or more video sources,

you may need to press the
projector, or the

Comp 1, Comp 2, S-video, or Video button

Source Search button on the

on the remote control to select the correct source. Allow a few
seconds for the projector to sync up after pressing the button.

■ If you’ve connected a notebook computer, make sure it’s set to

display on an external monitor. See page 33.

If you’re using a PC notebook:

■ Hold down the Fn key and press the function key that lets you

display on an external monitor. It may have an icon such as

, or it may be labelled
the projector to sync up after pressing it. Check your notebook’s
manual or online help for details.

CRT/LCD. Allow a few seconds for

On most systems, the or

CRT/LCD key lets you toggle

between the LCD screen and the projector, or display on both at
the same time.

■ Depending on your computer’s video card, you might need to use

the Display utility in the Control Panel to make sure that both the
LCD screen and external monitor port are enabled. See your
computer’s documentation or online help for details.

If you’re using a PowerBook or iBook with
Macintosh OS X:

1. From the Apple menu, select System Preferences, then click

Display.

2. Select

VGA Display or Color LCD, click Arrange or
Arrangement, then select Mirror Displays.

If you’re using a PowerBook or iBook with
Macintosh OS 9.x:

1. From the Apple menu, select Control Panels, then click

Monitors or Monitors and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.

4. If the

5. Select one of the listed

Arrange icon isn’t available, click the Monitor icon.

Simulscan resolutions. (Allow a few

seconds for the projector to sync up after making the selection.)

Solving Problems 83

The message Not Supported is displayed.

■ Make sure your computer’s resolution and frequency are

supported by the projector. See page 97. If necessary, change
your computer’s resolution setting as described below.

■ If you’re projecting from a composite or S-video source, make

sure the correct
page 57. It should be set to
60 Hz PAL video source, in which case it should be set to

Video Signal is selected in the Signal menu. See

Auto unless you are projecting from a

PAL60.

Only part of the computer image is displayed.

■ If you’re projecting from a computer or RGB video device, press

Auto button on the remote control. If this doesn’t work or if

the
you’re projecting from a component, composite, or S-video
device, you may need to adjust the
menu. See page 56 for more information.

■ If you’ve enlarged part of the image using the E-Zoom button

on the remote control, press the
and return to full display.

■ Try pressing the Resize button on the remote control to select a

different aspect ratio (ratio of length to height).

Position setting in the Signal

Esc button to cancel zooming

84 Solving Problems

■ Make sure your computer’s resolution setting is correct. Ideally,

it should be 1024

× 768 to match the projector’s native

resolution. If this option isn’t available, select one of the
supported display formats listed on page 98.

■ Windows:

Right-click the desktop, select

Properties, click the Settings

tab, and select a different resolution.

■ Macintosh OS X:

On the Apple menu, choose
click

Display (or Displays for OS X 10.3). Select a different

System Preferences, then

resolution.

■ Macintosh OS 9.x:

On the Apple menu, choose

Monitors or Monitors and Sound. Select a different

Control Panels, then click

resolution.

If this option isn’t available, select one of the other compatible
video formats listed on page 96.

■ You may also need to modify existing presentation files if you

created them for a different resolution. See your software
documentation for specific information.

■ If you’ve set up your projector and computer to display the same

image simultaneously, the projector may only project half the
image. Turn off the dual display settings.

The image isn’t rectangular, but trapezoid-shaped.

■ Make sure the projector isn’t placed off to one side of the screen,

at an angle, or the image won’t be rectangular. Place it directly in
front of the center of the screen, facing the screen squarely.

■ If you’ve tilted the projector upward, the image will be broader at

the top. Turn on Auto Keystone correction as described on
page 57 or hold down the or buttons on top of the
projector until the image is rectangular.

The image contains static or noise.

■ If you’re using a computer cable longer than 6 feet, or an

extension cable, the image quality may be reduced.

■ Keep your computer and video cables separated from the power

cord as much as possible to prevent interference.

■ The video signal may be split between the computer and the

projector. If you notice a decline in the projected image quality
when the image is displayed simultaneously on your notebook
computer and the projector, turn off the notebook’s LCD display.

Solving Problems 85

note

f

If you turn on Auto

Keystone

menu (see page 58) or change
the
Image menu (see page 54),
you may have trouble
adjusting the focus using the

ocus ring. Reset these settings
to their default values if you
want to use the focus ring; see
page 68.

in the Setting

Sharpness setting in the

■ If you’re projecting from a composite or S-video source, check the

Video Signal setting in the Signal menu. In most cases, leave it

Auto. If you’re using a 60-Hz PAL video source, change this

set at
setting to

■ Make sure the cables are securely connected at both ends.

■ If you’re projecting from a computer, select the correct resolution;

PAL60. See page 57 for details.

see “Compatible Computer Display Formats” on page 97.

■ If you’re projecting from a computer, press the Auto button on

the remote control or the

Enter button on the projector to adjust

tracking and sync automatically. If that doesn’t work, try
adjusting the

Sync and Tracking settings in the Signal menu. See

page 56.

The image is blurry.

■ Adjust the focus using the focus ring.

■ Make sure the lens cap is off.

■ There may be dirt or smears on the lens. Clean the lens as

described on page 70.

■ Make sure the lens is not fogged by condensation. You may need

to wait before using the projector after moving it from a cold
environment.

■ Make sure the projection distance is within the range described on

page 14.

■ Adjust the Sharpness setting on the Image menu (see page 54).

You should be able to see the effect on the screen immediately.

■ Adjust the Brightness and Contrast settings in the image menu;

see page 54.

86 Solving Problems

You see vertical stripes, flickering, or the image still looks
blurry after trying the solutions in the previous section.

■ If you’re projecting from a computer and displaying an image that

contains a lot of fine detail, you may notice one or more vertical
stripes or bands, or some of the characters may look heavy or
blurred. Press the
the projector’s tracking and sync settings.

■ If further adjustment is needed, you can fine-tune the Tracking

Sync settings manually using the Signal menu as described

and
on page 56.

1. Fill the screen with an image containing fine detail when
making these adjustments. For example, in Windows you can
select a pattern to appear as your desktop background. Or try
projecting black text on a white background.

Auto button on the remote control. This resets

note

For best results, adjust
tracking before you adjust
sync.

2. Adjust the

3. Adjust the

Tracking to eliminate vertical stripes.

Sync to increase the sharpness of the image or

eliminate flickering or signal interference.

The colors of the image are not right.

■ Make sure the input signal setting on the Signal menu matches

the signal from the connected device. If the image is too purple
and you’ve connected a computer or RGB video device to the

Computer1/Component Video1 or Computer2/Component
Video2

source. If you’ve connected a component video device to one of
these ports, select
If you’re projecting from a composite video or S-video source,
make sure the correct
message. See page 55 for details.

■ Try selecting a different Color Mode. See page 54 for

instructions.

■ If you’re displaying video, adjust the Color Intensity and Tint

settings on the Image menu. See page 54 for instructions.

port, select Computer1 or Computer2 as the input

Component Video1 or Component Video2.

Video Signal is selected on the Signal

note

Because of the different
technologies used, your
projected image may not
exactly match the colors on
your notebook or computer
monitor.

■ Adjust the Brightness and Contrast settings on the Image

menu. See page 54.

Solving Problems 87

■ Try adjusting the Color Adjustment setting on the Image menu.

See page 54.

■ Check your computer display settings to correct the color balance.

■ If the image seems dark, the lamp may be nearing time for

replacement. Check the lamp hours as described on page 61 and
replace it, if necessary, as described on page 72.

There is no sound.

■ Press the button on the remote control or projector to turn up

the volume.

■ If you’ve turned off the picture and sound, press the A/V Mute

button on the remote control to turn them on again.

■ If you’re using a VCR or other video source, make sure its volume

is not turned all the way down or muted. Also, make sure the
cables are connected correctly, as described in Chapter 1.

■ Make sure the audio cable is connected to the correct Audio port.

See page 21.

■ If your presentation includes computer audio, make sure the

volume control on your computer is not turned all the way down
or muted. Make sure the audio cable is securely connected to both
the projector and your computer’s headphone jack or

audio out jack. See page 21.

88 Solving Problems

■ The wrong source may be selected. Press the Source Search

button on the projector—or the Comp 1, Comp 2, S-Video, or

Video button on the remote control—to select the correct source.

Solving Password Problems

You have forgotten the password.

■ Write down the request code that appears in the Password Protect

Release screen and contact Epson. See “Where To Get Help” on
page 91.

■ If you turned on the password protect feature before setting the

password and no password was set before, try using the default
password:

0000.

The remote control is not available.

You must have the remote control to enter the password. If necessary,
you can purchase a replacement remote control from Epson. See
page 91 for details about ordering.

Solving Problems with the Remote Control

The projector doesn’t respond to remote control commands.

■ Make sure you are within 20 feet of the projector, and within

range of the projector’s front or back sensor (approximately 30° to
the left or right and 15° above or below).

■ The remote control batteries may not be installed correctly or may

be low on power. Replace the batteries as described on page 48.

■ Dim the room lights and turn off any fluorescent lights. Make

sure the projector is not in direct sunlight. Strong lighting,
especially fluorescent lights, may affect the projector’s infrared
receivers.

■ Turn off any nearby equipment that emits infrared energy, such

as a radiant room heater.

■ The P Power button is disabled while the Power light is

flashing. Wait for the light to stop flashing.

Solving Problems 89

You have lost the remote control.

You need the remote control to access many projector features. If you
have lost it, you can order another from Epson. See page 91 for details
about ordering.

You can’t control the mouse pointer with the remote
control.

■ Make sure the USB mouse cable is securely connected to both

your computer’s USB port and the projector’s USB port. For
details, see page 19.

■ To use the USB mouse connection on a PC, your system must

have a “clean” installation of Windows 98SE, Windows Me,
Windows XP, or Windows 2000. The connection may not work
correctly if your system was upgraded from Windows 95.

■ If you’re running Windows 98 or Me, you may need to install

USB drivers from your Windows CD-ROM. After you install the
drivers, restart both the computer and the projector to
resynchronize the setup.

■ You can’t use the wireless mouse function while using the

E-Zoom buttons on the remote, adjusting the volume, capturing

a user’s logo, or displaying a configuration or help menu.

90 Solving Problems

Solving Problems with the Projector’s Buttons

The projector’s buttons don’t work.

■ Operation Lock may be enabled. To disable it, press the

projector’s

■ The P Power button is disabled while the Power light is

flashing. Wait for the light to stop flashing.

Enter button for seven seconds.

Where To Get Help

Epson provides technical assistance through electronic support
services 24 hours a day, as listed in the following table.

Service Access

World Wide Web From the Internet, you can reach

Epson’s product support page at
http://support.epson.com. After selecting
your product, you can access troubleshooting
information, download product documentation,
and receive technical advice through e-mail.

Presenters Online Access tips, templates, and training for

developing successful presentations at

http://www.presentersonline.com

Telephone Support Services

To use the Epson PrivateLine Support service, call [phone]
and enter the PIN on the Epson PrivateLine Support card included
with your projector. This is the fastest way to speak to a live
representative, and it’s free. This service is available 6
Pacific Time, Monday through Friday, for the duration of your
warranty period.

AM to 6 PM,

You may also speak with a projector support specialist by dialing one
of these numbers:

■ U.S.: [phone], 6 AM to 6 PM, Pacific Time, Monday

through Friday

■ Canada: [phone], 6 AM to 6 PM, Pacific Time, Monday

through Friday

Toll or long distance charges may apply.

Solving Problems 91

Before you call, please have the following information ready:

■ Product name (PowerLite 821p)

■ Product serial number (located on the bottom of the projector)

■ Computer or video configuration

note

To purchase a replacement
remote control, call
[phone] (U.S.) or
[phone] (for dealer
referral in Canada).

■ Description of the problem

You can purchase screens, carrying cases, or other accessories
from Epson at [phone] or by visiting the Epson Store at
www.epsonstore.com (U.S. sales only). In Canada, please call
[phone] for dealer referral

.

92 Solving Problems

Technical Specifications

General

Type of display Poly-silicon TFT active matrix

Lens F=1.70 to 1.87, f=21.3 to 25.6 mm

Resolution 1024

Color reproduction Full color, 16.8 million colors

Brightness (ANSI) 2600 lumens (High brightness mode)

Contrast ratio 500:1

Image size 30 to 300 inches (0.8 to 7.6 meters)

Projection distance 2.8 to 48.3 feet (0.85 to 14.7 meters)

Projection methods Front, rear, ceiling

Focus adjustment Manual

Zoom adjustment Manual

Internal sound system 5 W monaural

Optical aspect ratio 4:3 (horizontal:vertical)

Zoom ratio 1:1.6

Noise level 36 dB (High brightness mode)

Keystone correction
angle

× 768 pixels

1900 lumens (Low brightness mode)

30 dB (Low brightness mode)

± 15° vertical (maximum)

93

note

Lamp life results vary
depending on
environmental conditions
and usage. Turn the
projector off when not
in use. Continuous
24-hour-a-day use may
reduce the overall life
of the product.

Projection Lamp

Power consumption 200 W

Lamp life About 2000 hours (High brightness);

3000 hours (Low brightness)

Remote Control

Range 20 feet (6 meters)

Operating angle About ± 30° horizontally

About ± 15° vertically

Batteries (2) Alkaline AAA

Mouse Compatibility

Supports USB (Type B)

Dimensions

Height 4.13 to 4.8 inches

(105 to 123 mm)

Width 13.78 inches (350 mm)

94 Technical Specifications

Depth 9.45 inches (272 mm)

Weight 8.9 lb (4.0 kg)

Electrical

Rated frequency 50/60 Hz

Power supply 100 to 120 VAC, 3.2 A

200 to 240 VAC, 1.6 A

Power consumption Operating: 280 W

Standby: 5 W

Environmental

Temperature Operating: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Humidity Operating: 20 to 80% RH,

non-condensing

Storage: 10 to 90% RH,
non-condensing

Operating altitude 0 to 7,500 ft (0 to 2,286 m)

Safety and Approvals

United States FCC 47CFR Part15B Class B (DoC)

UL60950 Third Edition

Canada ICES-003 Class B

CSA C22.2 No. 60950 (cUL)

CE Marking Directive 73/23/EEC, 89/336/EEC

IEC60950 Third Edition
EN 55022, EN 55024
IEC/EN61000-3-2
IEC/EN61000-3-3

Pixelworks
projector.

™

DNX™ ICs are used in this

Technical Specifications 95

Compatible Video Formats

You can use any of the following video sources: VCR, DVD player,
camcorder, digital camera, gaming console, or laser disc player. The
projector supports composite video, S-video, component video, and
RGB video, and it automatically senses the video format (HDTV,
SDTV, NTSC, PAL, or SECAM).

The projector supports these international video standards:

Mode Refresh Rate (Hz)

NTSC
NTSC 4:3
PAL
PAL 4:3
M-PAL
N-PAL
PAL60
SECAM
SECAM 4:3

HDTV (720p)
HDTV (1080i)
SDTV (480i)

SDTV (540i)
SDTV (480p)

60
60
50
50
60
50
60
50
50

60
60
60

50
60

96 Technical Specifications

Compatible Computer Display Formats

You can connect the projector to a wide range of computers, including
PCs and notebooks, Apple Macintosh, Power Macintosh series
(including G3, G4 and G5 systems), PowerBook computers, many
iMac and iBook series systems, and high-end workstations such as the

®

Sun

SPARCstation.

Although images are displayed at the projector’s native resolution of

1024 × 768 pixels, Epson’s patented SizeWise chip supports computer

display formats ranging from VGA through UXGA.

To project images output from a computer, the computer’s external
monitor signal must be set at a refresh rate (vertical frequency) that’s
compatible with the projector; see the following table for compatible
formats. For best results, the computer’s resolution should be set to
match the projector’s native resolution (1024
isn’t available, select one of the other compatible formats:

■ Windows:

Right-click the desktop, select
and select a compatible resolution. (For a notebook displaying
through an external monitor port, you’ll need to click the

Advanced button on the Settings tab, then adjust the resolution

of the external monitor.)

™

× 768). If this resolution

Properties, click the Settings tab,

■ Macintosh OS X:

From the Apple menu, select

Displays. Make sure the VGA Display or Color LCD dialog box

is selected, then click the

System Preferences, then click

Display tab and select a compatible

resolution.

■ Macintosh OS 9.x:

On the Apple menu, choose

Monitors or Monitors and Sound. Click the Monitor tab and

Control Panels, then click

select a compatible resolution for your external monitor.

You may need to modify existing presentation files if you created them
for a different resolution. See your software documentation for details.

Technical Specifications 97

The projector supports these monitor display formats:

Mode Refresh Rate (Hz) Resolution

VGA EGA 70 640 × 350

VGA—60
VESA—60
VESA—72
VESA—75
VESA—85

SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—85

XGA—60
XGA—70
XGA—75
XGA—85

SXGA1—70
SXGA1—75
SXGA1—85

SXGA2—60
SXGA2—75
SXGA2—85

SXGA3—60
SXGA3—75
SXGA3—85

60
60

72
75
85

56
60
72
75
85

60
70
75
85

70
75
85

60
75
85

60
75
85

UXGA—60 60 1600

iMAC VGA
iMAC SVGA
iMAC XGA
MAC13
MAC16
MAC19—60
MAC19
MAC21

SDTV (540i)
SDTV (480i)
SDTV (480p)

HDTV (720p)
HDTV (1080i)

117
95
75
67
75
60
75
75

50
60
60

60
60

640

× 480

640 × 480
640

× 480

640

× 480

640

× 480

800

× 600

800

× 600

800

× 600

800

× 600

800

× 600

1024

× 768

1024

× 768

1024

× 768

1024

× 768

1152

× 864

1152

× 864

1152

× 864

1280

× 960

1280

× 960

1280

× 960

1280

× 1024

1280

× 1024

1280

× 1024
× 1200

640

× 480

800

× 600

1024

× 768

640

× 480

832

× 624

1024

× 768

1024

× 768

1152

× 870

720 × 540
640

× 480

640 × 480

× 720

1280
1920 × 1080

98 Technical Specifications

Notices

This appendix includes safety instructions and other important information

about your Epson PowerLite projector.

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

■ Do not place the projector on an unstable cart, stand, or table.

■ Do not use the projector near water or sources of heat.

■ Use the type of power source indicated on the projector. If you are not

sure of the power available, consult your dealer or power company.

■ Place the projector near a wall outlet where the plug can be easily

unplugged.

Placez l’appareil près d’une prise de courant où la fiche peut être débranchée
facilement.

■ Insert the projector’s three-wire grounding-type plug into a properly

grounded outlet. If you have a two-prong outlet, contact an electrician
to replace it. Do not hold the plug with wet hands.

■ Take the following precautions for the plug. Failure to comply with

these precautions could result in sparks or fire: Do not insert the plug
into an outlet with dust present. Insert the plug firmly into the outlet.

■ Do not overload wall outlets, extension cords, or integral convenience

receptacles. This can cause fire or electric shock.

■ Do not place the projector where the cord can be walked on. This may

result in fraying or damage to the plug.

■ Unplug the projector from the wall outlet before cleaning. Use a damp

cloth for cleaning. Do not use liquid or aerosol cleaners.

■ Do not block the slots and openings in the projector case. They provide

ventilation and prevent the projector from overheating. Do not operate
the projector on a sofa, rug, or other soft surface, or in a closed-in
cabinet unless proper ventilation is provided.

99

■ Never push objects of any kind through the cabinet slots. Never spill

liquid of any kind into the projector.

■ Except as specifically explained in this User’s Guide, do not attempt to

service this product yourself. Refer all servicing to qualified personnel.
Opening or removing covers may expose you to dangerous voltages and
other hazards.

■ Unplug the projector from the wall outlet and refer servicing to qualified

service personnel under the following conditions: When the power cord
or plug is damaged or frayed. If liquid has been spilled into the
projector, or if it has been exposed to rain or water. If it does not operate
normally when you follow the operating instructions, or if it exhibits a
distinct change in performance, indicating a need for service. If it has
been dropped or the housing has been damaged.

■ The lamp(s) in this product contain mercury. Please consult your

state and local regulations regarding disposal or recycling. Do not put in
the trash.

■ Unplug the projector during lightning storms or when it will not

be used for extended periods.

■ Do not place the projector and/or remote control on top of

heat-producing equipment or in a hot location.

■ If you use the projector in a country other than where you purchased it,

use the correct power cord for that country.

■ Do not stand on the projector or place heavy objects on it.

■ Do not use the projector outside of the required temperature range of

41 to 95 °F (5 to 35 °C). Doing so may cause an unstable display and
could lead to projector damage.

■ Do not store the projector outside of the required temperature range of

14 to 140 °F (
time. Doing so may cause damage to the case.

−10 to 60 °C) or in direct sunlight for long periods of

100 Notices

WARNING: This product contains chemicals, including lead, known to the
State of California to cause birth defects or other reproductive harm. Wash

hands after handling.